Skip to main content
Log in

Synthesis of Ni–B/diamond-Y2O3 binary nano-composite coatings and research on corrosion resistance and wear resistance of coatings with different pulse frequencies

  • Original Paper
  • Published:
Journal of Solid State Electrochemistry Aims and scope Submit manuscript

Abstract

In this article, Ni–B composite electrodeposition was prepared by nanodiamond and Y2O3 nanoparticles. Due to the synergistic strengthening effect of the two reinforcing phase particles on the Ni–B composite coating, the wear and corrosion resistance of the Ni–B/diamond-Y2O3 composite coating is significantly better than that of the single reinforcing material composite coating. In addition, the effect of electrodeposition pulse frequency on Ni–B/diamond-Y2O3 composite coating was studied in detail, and its characterization and performance tests were carried out. The results show that the Ni–B/diamond-Y2O3 nanocomposite coatings prepared with a pulse frequency of 100 Hz have finer grains and no agglomeration. The Ni–B/diamond-Y2O3 nanocomposite coating has the highest impedance under the pulse frequency of 100 Hz, the corrosion inhibition rate is 98.70%, and it has good corrosion resistance. At the same time, in the mechanical property test, the average microhardness is as high as 661.90 HV, the average friction coefficient is only 0.206, and the wear resistance is excellent. In conclusion, the Ni–B/diamond-Y2O3 nanocomposite coatings prepared under 100 Hz pulse have excellent wear and corrosion resistance.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14

Similar content being viewed by others

Data availability

Due to the sensitive nature of the questions asked in this study, survey respondents were assured raw data would remain confidential and would not be shared.

References

  1. Sorensen PA, Kiil S, Dam-Johansen K, Weinell CE (2009) Anticorrosive coatings: a review. J Coat Technol Res 6(2):135–176. https://doi.org/10.1007/s11998-008-9144-2

    Article  CAS  Google Scholar 

  2. Li B, Mei T, Li D, Du S, Zhang W (2019) Structural and corrosion behavior of Ni-Cu and Ni-Cu/ZrO2 composite coating electrodeposited from sulphate-citrate bath at low Cu concentration with additives. J Alloy Compd 804:192–201. https://doi.org/10.1016/j.jallcom.2019.06.381

    Article  CAS  Google Scholar 

  3. Rasooli A, Safavi MS, Babaei F, Ansarian A (2020) Electrodeposited Ni–Fe–Cr2O3 nanocomposite coatings: a survey of influences of Cr2O3 nanoparticles loadings in the electrolyte. J Alloys Comp 822. https://doi.org/10.1016/j.jallcom.2020.153725.

  4. Yildiz RA, Genel K, Gulmez T (2021) Effect of electroless Ni-B and Ni-W-B coatings on the corrosion-fatigue behaviour of 7075 Al alloy. Int J Fatigue 144. https://doi.org/10.1016/j.ijfatigue.2020.106040

  5. Tabish M, Malik MU, Khan MA, Yasin G, Asif HM, Anjum MJ, Khan WQ, Ibraheem S, Nguyen TA, Slimani Y, Nazir MT (2021) Construction of NiCo/graphene nanocomposite coating with bulges-like morphology for enhanced mechanical properties and corrosion resistance performance. J Alloy Compd 867:9. https://doi.org/10.1016/j.jallcom.2021.159138

    Article  CAS  Google Scholar 

  6. Zhang JB, Huang YC, Wu H, Geng SJ, Wang FH (2021) Corrosion protection properties of an environmentally friendly polyvinyl alcohol coating reinforced by a heating treatment and lignin nanocellulose. Prog Org Coat 155:12. https://doi.org/10.1016/j.porgcoat.2021.106224

    Article  CAS  Google Scholar 

  7. Sayyad F, Senanayake R (2021) Experimental investigation on surface roughness of electroless Ni-B-TiO2 nanocomposite coatings. Sadhana-Acad Proc Eng Sci 46(2). https://doi.org/10.1007/s12046-021-01601-8

  8. Wang SJ, Wang YX, Sh, X, Tay S, Gao W, Shakoor RA, Kahraman R (2015) Preparation and property of duplex Ni-B-TiO2/Ni nano-composite coatings. Int J Modern Phys B 29(10–11). https://doi.org/10.1142/s0217979215400226

  9. Kallel M, Masseoud M, Vesco S, Barletta M, Elleuch K (2020) The effects of TiO2 sol concentration on single- and multiple-scratch damage in electroplated Ni-B-TiO2 sol composite coating. Ceram Int 46(3):3767–3776. https://doi.org/10.1016/j.ceramint.2019.10.099

    Article  CAS  Google Scholar 

  10. Radwan AB, Shakoor RA (2020) Aluminum nitride (AlN) reinforced electrodeposited Ni–B nanocomposite coatings. Ceram Int 46(7):9863–9871. https://doi.org/10.1016/j.ceramint.2019.12.261

    Article  CAS  Google Scholar 

  11. Waware US, Hamouda AMS, Wasekar NP (2018) Mechanical properties, thermal stability and corrosion behavior of electrodeposited Ni-B/AlN nanocomposite coating. Surf Coat Technol 337:335–341. https://doi.org/10.1016/j.surfcoat.2018.01.028

    Article  CAS  Google Scholar 

  12. Shakoor RA, Kahraman R, Waware US, Wang Y, Gao W (2014) Synthesis and properties of electrodeposited Ni–B–CeO2 composite coatings. Mater Des 59:421–429. https://doi.org/10.1016/j.matdes.2014.03.024

    Article  CAS  Google Scholar 

  13. Gultekin D, Duru E, Akbulut H (2021) Improved wear behaviors of lead-free electroless Ni-B and Ni-B/CeO2 composite coatings. Surface Coat Technol 422. https://doi.org/10.1016/j.surfcoat.2021.127525

  14. Pancrecious JK, Deepa JP, Jayan V, Bill US, Rajan TPD, Pai BC (2018) Nanoceria induced grain refinement in electroless Ni-B-CeO2 composite coating for enhanced wear and corrosion resistance of Aluminium alloy. Surf Coat Technol 356:29–37. https://doi.org/10.1016/j.surfcoat.2018.09.046

    Article  CAS  Google Scholar 

  15. Li D, Li B, Du S, Zhang W (2019) Synthesis of a novel Ni–B/YSZ metal-ceramic composite coating via single-step electrodeposition at different current density. Ceram Int 45(18):24884–24893. https://doi.org/10.1016/j.ceramint.2019.09.121

    Article  CAS  Google Scholar 

  16. Huang CA, Yang SW, Shen CH, Cheng KC, Wang H, Lai PL (2019) Fabrication and evaluation of electroplated Ni–diamond and Ni–B–diamond milling tools with a high density of diamond particles. Int J Adv Manuf Technol 104(5–8):2981–2989. https://doi.org/10.1007/s00170-019-04174-3

    Article  Google Scholar 

  17. Zhang Y, Zhang S, He Y, Li H, He T, Fan Y, Zhang H (2021) Mechanical properties and corrosion resistance of pulse electrodeposited Ni-B/B4C composite coatings. Surface Coat Technol 421:127458. https://doi.org/10.1016/j.surfcoat.2021.127458

  18. Zhang W (2018) Electrochemical properties and XPS analysis of Ni-B/SiC nanocomposite coatings. Int J Electrochem Sci 3516–3526. https://doi.org/10.20964/2018.04.30

  19. Krishnaveni K, Sankara Narayanan TSN, Seshadri SK (2009) Electrodeposited Ni–B–Si3N4 composite coating: preparation and evaluation of its characteristic properties. J Alloys Compd 466(1–2):412–420. https://doi.org/10.1016/j.jallcom.2007.11.104

  20. Ogihara H, Miyamoto K, Udagawa K, Saji T (2011) Electrodeposition of super hard Ni–B/diamond composite coatings. Chem Lett 40(10):1072–1073. https://doi.org/10.1246/cl.2011.1072

    Article  CAS  Google Scholar 

  21. Lekka M, Offoiach R, Lanzutti A, Mughal MZ, Sebastiani M, Bemporad E, Fedrizzi L (2018) Ni-B electrodeposits with low B content: Effect of DMAB concentration on the internal stresses and the electrochemical behaviour. Surf Coat Technol 344:190–196. https://doi.org/10.1016/j.surfcoat.2018.03.018

    Article  CAS  Google Scholar 

  22. Fang X, Jin G, Cui XF, Liu JN (2016) Evolution characteristics of residual stress in metastable Ni-B alloy coatings identified by nanoindentation. Surf Coat Technol 305:208–214. https://doi.org/10.1016/j.surfcoat.2016.08.042

    Article  CAS  Google Scholar 

  23. El-Sherik AM, Shirokoff J, Erb U (2005) Stress measurements in nanocrystalline Ni electrodeposits. J Alloys Compds 389(1):140–143. https://doi.org/10.1016/j.jallcom.2004.08.010

  24. Shakoor R, Waware U, Ali,K, Kahraman R, Popelka A, Yusuf M, Hasan A (2017) Novel electrodeposited Ni-B/Y2O3 composite coatings with improved properties. Coatings 7(10). https://doi.org/10.3390/coatings7100161

  25. Xing S, Wang L, Jiang C, Liu H, Zhu W, Ji V (2020) Influence of Y2O3 nanoparticles on microstructures and properties of electrodeposited Ni–W–Y2O3 nanocrystalline coatings. Vacuum 181. https://doi.org/10.1016/j.vacuum.2020.109665

  26. Zhang R, Li Z, Yu X, Cui G (2018) Characterisation and properties of Ni–W–Y2O3–ZrO2 nanocomposite coating. Surf Eng 35(7):578–587. https://doi.org/10.1080/02670844.2018.1547246

    Article  CAS  Google Scholar 

  27. Zhou XY, Wang YY, Liu XL, Liang ZP, Jin H (2018) Electrodeposition kinetics of Ni/nano-Y2O3 composite coatings. Metals 8(9). https://doi.org/10.3390/met8090669

  28. Li B, Li D, Zhang J, Chen W, Zhang W (2019) Electrodeposition of Ni-W/TiN-Y2O3 nanocrystalline coating and investigation of its surface properties and corrosion resistance. J Alloy Compd 787:952–962. https://doi.org/10.1016/j.jallcom.2019.02.168

    Article  CAS  Google Scholar 

  29. Li B, Zhang W, Li D, Wang J, Chen W, Liu Y (2019) Preparation of Ni W/TiN Y2O3 composite ceramic coating for metallic parts protection by direct current deposition. Ceram Internat 45(10):13242–13250. https://doi.org/10.1016/j.ceramint.2019.04.010

  30. Li B, Zhang W, Mei T, Miao Y (2020) Fabrication of Ni–B/TiC–Y2O3 nanocomposites by one-step electrodeposition at different duty cycle and evaluation of structural, surface and performance as protective coating. J Alloys Compd 823. https://doi.org/10.1016/j.jallcom.2020.153888

  31. Ogihara H, Hara A, Miyamoto K, Shrestha NK, Kaneda T, Ito S, Saji T (2010) Synthesis of super hard Ni-B/diamond composite coatings by wet processes. Chem Commun (Camb) 46(3):442–444. https://doi.org/10.1039/b914242h

    Article  CAS  Google Scholar 

  32. Monteiro OR, Murugesan S, Khabashesku V (2015) Electroplated Ni–B films and Ni–B metal matrix diamond nanocomposite coatings. Surf Coat Technol 272:291–297. https://doi.org/10.1016/j.surfcoat.2015.03.049

    Article  CAS  Google Scholar 

  33. Li H, He Y, Luo P, Fan Y, Yu H, Wang Y, He T, Li Z, Zhang H (2021) Influence of pulse frequency on corrosion resistance and mechanical properties of Ni-W/B4C composite coatings. Colloids Surfaces A: Physicochem Eng Aspects 629. https://doi.org/10.1016/j.colsurfa.2021.127436

  34. Jiang YC, Xu YH, Feng GT, Yao HC (2016) High-frequency pulse electrodeposition and characterization of Ni-Co/ZrO2 nanocomposite coatings. J Mater Science-Mater Electron 27(8):8169–8176.https://doi.org/10.1007/s10854-016-4820-y

  35. Xu YH, Liu SL, Liu XW (2011) Wear resistance of high frequency pulse electroplating Ni-SiC nano-composite coating. In: 10th China Int Nanosci Technol Symp. Hangzhou, Peoples R China

  36. Xia FF, Tian JY, Ma CY, Potts M, Guo X (2014) Effect of pulse frequency on microstructural, nanomechanical, and wear properties of electrodeposited Ni-TiN composite coatings. J Appl Phys 116(23). https://doi.org/10.1063/1.4904190

  37. Carpenter CR, Shipway PH, Zhu Y, Weston DP (2011) Effective dispersal of CNTs in the fabrication of electrodeposited nanocomposites. Surface Coat Technol 205(20):4832–4837. https://doi.org/10.1016/j.surfcoat.2011.04.070

  38. Doğan F, Uysal M, Duru E, Akbulut H, Aslan S (2020) Pulsed electrodeposition of Ni-B/TiN composites: effect of current density on the structure, mechanical, tribological, and corrosion properties. J Asian Ceram Soc 8(4):1271–1284. https://doi.org/10.1080/21870764.2020.1840704

    Article  Google Scholar 

Download references

Funding

This research was financially supported by Open Fund (PLN161, PLN201806) of State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation (Southwest Petroleum University), the Research Program of Science and Technology Department of Sichuan Province (2018JY0302, 18YYJC0018), the National Natural Science Foundation of China (51774245) and the project of Chengdu Science and Technology Bureau (2018-CY02-00024-GX).

Author information

Authors and Affiliations

Authors

Contributions

Jinxue Song: completed the main experiment; data analysis and related chart making; writing draft. Yihan Zhang: completed the main experiment; data analysis and related chart making; writing draft. Yi He: funding acquisition; project administration; resources. Shihong Zhang: project administration; resources. Hongjie Li: paper review and suggestion for revision. Yuxin Xiang: do some experiments. Yi Fan: paper review and suggestion for revision. Ruxia Song: supervision and proofreading. Bo Liu: supervision and proofreading.

Corresponding authors

Correspondence to Yi He or Shihong Zhang.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary Information

Below is the link to the electronic supplementary material.

Supplementary file1 (DOCX 341 KB)

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Song, J., Zhang, Y., He, Y. et al. Synthesis of Ni–B/diamond-Y2O3 binary nano-composite coatings and research on corrosion resistance and wear resistance of coatings with different pulse frequencies. J Solid State Electrochem 27, 207–221 (2023). https://doi.org/10.1007/s10008-022-05303-x

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10008-022-05303-x

Keywords

Navigation