Abstract
Among various materials used for structures, TRIP steel has attracted the interest of the scientific community because TRIP steel indicates better performances such as formability, toughness and energy absorption as well as strength and ductility than other kinds of advanced high strength steel because of strain-induced martensitic transformation. From a microstructural point of view, two mechanisms are usually considered to explain the high performances: the Magee and the Greenwood-Johnson effects: however, it has not been proven yet. On the other hand, even though TRIP steel shows the excellent energy absorption under the high-speed deformation, the amount of martensite is very small by an influence of the heat generation with plastic transformation. In order to solve this paradox and explain macroscopic performances from the microscopic deformation mechanism, a concept of a spatio-temporal multiscale should be introduced. In this paper, research works done by the one of the authors on the mechanism of high functionalization in TRIP steel from the viewpoint of a spatio-temporal hierarchy are summarized with reviewing some related papers.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Altenbach H, Kolupaev V (2015) Classical and non-classical failure criteria. In: Altenbach H, Sadowski T (eds) Failure and damage analysis of advanced materials, CISM courses and lectures no. 560. Springer, Wien, New York, pp 1–66
Asaro R (1983) Crystal plasticity. Trans ASME J Appl Mech 50:921–934
ASTM Standard E399-90 (2002) Standard test method for plane strain fracture toughness of metallic materials. Annual book of ASTM standards. ASTM International, Baltimore, pp 443–473
Atluri S, Nishioka T, Nakagaki M (1984) Incremental path-independent integrals in inelastic and dynamic fracture mechanics. Eng Frac Mech 20:209–244
Bohme W, Kalthoff J (1982) The behavior of notched bend specimens in impact testing. Int J Fract 20:139–143
Chatterjee S (2006) Transformations in TRIP-assisted steels: microstructure and properties. PhD thesis, Darwin College, University of Cambridge
Cortes J, Tsuta T, Mitani Y, Osakada K (1992) Flow stress and phase transformation analyses in the austenitic stainless steel under cold working (part I, phase transformation characteristics and constitutive formulation by energetic criterion). JSME Int J 35:201–209
Dan W, Zhang W, Li S, Lin Z (2007) A model for strain-induced martensitic transformation of TRIP steel with strain rate. Comp Mater Sci 40:101–107
Delannay L, Lani F, Jacques P (2005) Simulation of deep-drawing of TRIP-assisted multiphase steel based on a micro-macro modelling. In: Boudeau N (ed) 24th international deep-drawing research group Congress, Kluwer, pp 1–10
Fischer F, Reisner G, Werner E, Tanaka K, Cailletaud G, Antretter T (2000) A new view on transformation induced plasticity (TRIP). Int J Plast 16:723–748
Greenwood G, Johnson R (1965) The deformation of metals under small stresses during phase transformation. Proc Roy Soc A 283:403–422
He Y, Sun Q (2010) Rate-dependent domain spacing in a stretched NiTi strip. Int J Solids Struct 47:2775–2783
Hecker S, Stout M, Staudhammer K, Smith L (1982) Effects of strain state and strain rate on deformation-induced transformation in 304 stainless steel: part 1. Magnetic measurements and mechanical behavior. Metall Trans A 13A:619–626
Iwamoto T (2004) Multiscale computational simulation of deformation behavior of TRIP steel with growth of martensitic particles in unit cell by asymptotic homogenization method. Int J Plast 20:841–869
Iwamoto T, Tsuta T (2000) Computational simulation of the dependence of the austenitic grain size on the deformation behavior of TRIP steels. Int J Plast 16:791–804
Iwamoto T, Tsuta T (2002a) Assessment of geometrical orientation of martensitic particles in TRIP steel by Fourier and wavelet transformation image analyses. Key Eng Mater 233–236:627–636
Iwamoto T, Tsuta T (2002b) Computational simulation on deformation behavior of CT specimens of TRIP steels under mode I loading for evaluation of fracture toughness. Int J Plast 18:1583–1606
Iwamoto T, Tsuta T (2003) Assessment geometrical orientation of martensitic particles in TRIP steel by Fourier and wavelet transformation image analysis. Key Eng Mater 233–236:627–636
Iwamoto T, Tsuta T (2004) Finite element simulation of martensitic transformation in single-crystal TRIP steel based on crystal plasticity with cellular automata approach. Key Eng Mater 274–276:679–684
Iwamoto T, Tsuta T, Tomita Y (1998) Investigation on deformation mode dependence of strain-induced martensitic transformation in TRIP steels and modeling of transformation kinetics. Int J Mech Sci 40:173–182
Iwamoto T, Kawagishi Y, Tsuta T, Morita S (2001) Identification of constitutive equation for TRIP steel and its application to improve mechanical properties. JSME Int J Ser A 44:443–452
Iwamoto T, Cherkaoui M, Sawa T (2008) A study on impact deformation and transformation behavior of TRIP steel by finite element simulation and experiment. Int J Mod Phys B 22:5985–5990
Jiang F, Rohatgi A, Vecchio K, Cheney J (2004) Analysis of the dynamic responses for a pre-cracked three-point bend specimen. Int J Fract 127:147–165
Kalthoff J (1985) On the measurement of dynamic fracture toughness—a review of recent work. Int J Fract 27:277–298
Kazanci Z, Bathe K (2012) Crushing and crashing of tubes with implicit time integration. Int J Impact Eng 42:80–88
Keeler S, Kimchi S (2014) Advanced high-strength steels application guidelines version 5.0. Technical report 1–3, World Auto Steel
Kobayashi T, Yamamoto I, Ninomi M (1986) Evaluation of dynamic fracture toughness parameters by instrumented Charpy impact test. Eng Frac Mech 24:773–782
Leblond J, Mottet G, Devaux J (1986) A theoretical and numerical approach to the plastic behavior of steels during phase transformations II: study of classical plasticity for ideal-plastic phases. J Mech Phys Solids 34:411–432
Lichtenfeld J, Tyne C, Mataya M (2006) Effect of strain rate on stress-strain behavior of alloy 309 and 304L austenitic stainless steel. Metall Mater Trans A 37:147–161
Magee C (1966) Transformation kinetics, micro-plasticity and aging of martensite in Fe—31Ni. PhD thesis, Carnegie Institute of Technology, Pittsburgh, PA
Matsumura O, Sakuma Y, Takechi H (1987) Enhancement of elongation by retained austenite in inter critical annealed 0.4 C-1.5 Si-0.8 Mn steel. Trans Iron Steel Inst Jpn 27:570–579
Murr L, Staudhammer K, Hecker S (1982) Effects of strain state and strain rate on deformation-induced transformation in 304 stainless steel: part 2. Microstructural study. Metall Trans A 13A:626–635
Nakayama J (1964) A bending method for direct measurement of fracture energy of brittle material. Jpn J Appl Phys 3:422–423
Nanga S, Pineau A, Tanguy B, Nazé L, Santacreu P (2009) Plasticity and strain induced martensitic transformation in two austenitic stainless steels. In: Olson G, Lieberman D, Saxena A (eds) Proceedings of international conference on martensitic transformations (ICOMAT). Wiley, Hoboken, NJ, pp 341–348
Nemes J, Eftis J (1993) Constitutive modelling on the dynamic fracture of smooth tensile bars. Int J Plast 9:243–270
Olson G, Cohen M (1975) Kinetics of strain-induced martensitic nucleation. Metall Trans A 6A:791–795
Peirce D, Shin C, Needleman A (1984) A tangent modulus method for rate dependent solids. Comp Struct 18:875–887
Sachdev A (1983) Effect of retained austenite on the yielding and deformation behavior of a dual phase steel. Acta Metall 31:2037–2042
Server W, Wullaert R, Sheckherd J (1977) Evaluation of current procedures for dynamic fracture toughness testing. In: Barsom J (ed) Flaw growth and fracture, vol STP 631. ASTM, Philadelphia, pp 446–461
Shi L, Hashimoto S, Iwamoto T (2013) An experimental study on rate sensitivity of \(J\)-integral and its evaluation by small punch test for TRIP steel. Eng Trans 61:119–136
Shin H, Ha T, Chang Y (2001) Kinetics of deformation induced martensitic transformation in a 304 stainless steel. Scr Mater 45:823–829
Stringfellow R, Parks D, Olson G (1992) A constitutive model for transformation plasticity accompanying strain-induced martensitic transformations in metastable austenitic steels. Acta Metall 40:1703–1716
Taleb L, Petit S (2006) New investigations on transformation induced plasticity and its interaction with classical plasticity. Int J Plast 22:110–130
Taleb L, Sidoroff F (2003) A micromechanical modeling of the Greenwood-Johnson mechanism in transformation induced plasticity. Int J Plast 19:1821–1842
Talonen J, Aspegren P, Hanninen H (2014) Comparison of different methods for measuring strain induced \(\alpha ^{\prime }\)—martensite content in austenitic steels. J Mater Sci Tech 20:1506–1512
Tamura I (1982) Deformation-induced martensitic transformation and transformation-induced plasticity in steels. Met Sci 16:245–253
Tomita Y, Iwamoto T (1995) Constitutive modeling of TRIP steel and its application to the improvement of mechanical properties. Int J Mech Sci 37:1295–1305
Tomita Y, Iwamoto T (2001) Computational prediction of deformation behavior of TRIP steels under cyclic loading. Int J Mech Sci 43:2017–2034
Tomita Y, Shibutani Y (2000) Estimation of deformation behavior of TRIP steels-smooth/ringed-notched specimens under monotonic and cyclic loading. Int J Plast 16:769–789
Zackay V, Parker E, Fahr D, Busch R (1967) Enhancement of ductility in high strength steels. ASTM Trans 60:252–259
Zaera R, Rodriguez-Martinez J, Casado A, Fernandez-Saez J, Rusinek A, Pesci R (2012) A constitutive model for analyzing martensite formation in austenitic steels deforming at high strain rates. Int J Plast 29:77–101
Acknowledgments
The authors gratefully acknowledge Professor Nobutada Ohno for his encouragement on our project all the time.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2015 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Iwamoto, T., Pham, H.T. (2015). Review on Spatio-Temporal Multiscale Phenomena in TRIP Steels and Enhancement of Its Energy Absorption. In: Altenbach, H., Matsuda, T., Okumura, D. (eds) From Creep Damage Mechanics to Homogenization Methods. Advanced Structured Materials, vol 64. Springer, Cham. https://doi.org/10.1007/978-3-319-19440-0_7
Download citation
DOI: https://doi.org/10.1007/978-3-319-19440-0_7
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-19439-4
Online ISBN: 978-3-319-19440-0
eBook Packages: EngineeringEngineering (R0)