Skip to main content
SpringerLink
Log in

Determination of Tool Wear in Finishing

  • Published:
Russian Engineering Research Aims and scope

Abstract

The resultant microcutting trajectory in surface machining on plane-finishing equipment is determined by computer simulation, taking account of the technological, kinematic, and geometric parameters of the machined surfaces and the lap. On that basis, the lap–workpiece contact spot is determined, and the wear of the lap and workpieces is calculated.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Yuan, J., Yao, W., Zhao, P., et al., Kinematics and trajectory of both-sides cylindrical lapping process in planetary motion type, Int. J. Mach. Tools Manuf., 2015, vol. 92, pp. 60–71.

    Article  Google Scholar 

  2. Orlov, P.N., Tekhnologicheskoe obespechenie kachestva detalei metodami dovodki (Technological Support of Quality of the Parts by Finishing), Moscow: Mashinostroenie, 1988.

  3. Muratov, K.R., Influence of rigid and frictional kinematic linkages in tool–workpiece contact on the uniformity of tool wear, Russ. Eng. Res., 2016, 36, no. 4, pp. 321–323. https://doi.org/10.3103/S1068798X16040122

    Article  Google Scholar 

  4. Nekrasov, V.P. and Muratov, R.A., Machines with raster kinematics for finishing surfaces of constant curvature, in Sovremennye organizatsionnye tekhnologicheskie i konstruktorskie metody upravleniya kachestvom: Sbornik nauchnykh trudov (Modern Organizational Technological and Design Methods of Quality Management: Collection of Scientific Papers), Perm: Permsk. Gos. Tekh. Univ., 2006, pp. 96–115.

  5. Muratov, K.R., Gashev, E.A., Ablyaz, T.R., et al., Determining the actual contact area in mutual lapping of surfaces, Russ. Eng. Res., 2021, vol. 41, no. 5, pp. 437–438. https://doi.org/10.3103/S1068798X21050130

    Article  Google Scholar 

  6. Uzunyan, M.D., Almazno-iskrovoe shlifovanie tverdykh splavov (Diamond Spark Grinding of Hard Alloys), Khar’kov: Nats. Tekh. Univ. “Khar’kovsk. Politekh. Inst.”, 2003.

Download references

Funding

Financial support was provided by the Russian Ministry of Science and Higher Education (project FSNM-2020-0028).

Author information

Authors and Affiliations

  1. Perm National Research Polytechnic University, Perm, Russia

    M. S. Permyakov, K. R. Muratov, T. R. Ablyaz & E. A. Gashev

  2. Almetyevsk State Oil Institute, Almetyevsk, Tatarstan, Russia

    A. A. D’yakonov

Authors
  1. M. S. Permyakov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. K. R. Muratov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. A. D’yakonov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. T. R. Ablyaz
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. E. A. Gashev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to M. S. Permyakov, A. A. D’yakonov or T. R. Ablyaz.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Permyakov, M.S., Muratov, K.R., D’yakonov, A.A. et al. Determination of Tool Wear in Finishing. Russ. Engin. Res. 42, 838–840 (2022). https://doi.org/10.3103/S1068798X22080202

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X22080202

Keywords:

Search

Navigation