Skip to main content
SpringerLink
Log in

Production of Large Disks from Cylindrical Blanks by Plastic Deformation. 5. Comparison of Theoretical and Experimental Results

  • Published:
Russian Engineering Research Aims and scope

Abstract—Comparison of calculation results and experimental data shows that the model derived for the plastic deformation of large disks or hard-to-deform disks is very precise and reliable. On the basis of the formulas obtained, the deforming forces may be determined and defects (irregularities) associated with plastic deformation may be predicted at the industrial design stage.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 11.
Fig. 12.
Fig. 13.
Fig. 14.
Fig. 15.

Similar content being viewed by others

REFERENCES

  1. Vorontsov, A.L., Plastic deformation of large disks from cylindrical billets. Part 1: Objectives, Vestn. Mashinostr., 2018, no. 3, pp. 61–63.

  2. Vorontsov, A.L., Production of large disks from cylindrical blanks by plastic deformation. 2. Introduction of central punch to create a depression, Russ. Eng. Res., 2019, vol. 39, no. 7, pp. 567–570.

    Article  Google Scholar 

  3. Vorontsov, A.L., Production of large disks from cylindrical blanks by plastic deformation. 3. Final stage of implementation of the central punch, Vestn. Mashinostr., 2019, no. 5, pp. 49–52.

  4. Vorontsov, A.L., Production of large disks from cylindrical blanks by plastic deformation. 4. Deformation of the protrusion of the ring punch, Vestn. Mashinostr., 2019, no. 6, pp. 57–59.

  5. Semenov, E.I., Kovka i ob”emnaya shtampovka (Forging and Bulk Forming), Moscow: Vysshaya Shkola, 1972.

  6. Vorontsov, A.L., Teoriya i raschety protsessov obrabotki metallov davleniem (Theory and Calculations of Metal Forming by Pressure), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2014, vol. 2.

  7. Vorontsov, A.L., New solution of complex variational problems by the example of the description of the shape change of the billet during piercing, Kuznechno-Shtampovochnoe Proizvod.–Obrab. Mater. Davleniem, 2009, no. 10, pp. 3–8.

  8. Vorontsov, A.L., Theory of free drafting of a hollow cylindrical billet, Vestn. Mashinostr., 2006, no. 4, pp. 54–58.

  9. Vorontsov, A.L., Technological calculations of the free drafting of a hollow cylindrical billet, Vestn. Mashinostr., 2006, no. 5, pp. 64–69.

  10. Dmitriev, A.M. and Vorontsov, A.L., Physical patterns and determination of the power parameters of extrusion of hollow cylindrical products, Kuznechno-Shtampovochnoe Proizvod.–Obrab. Mater. Davleniem, 2004, no. 6, pp. 3–8.

Download references

Author information

Authors and Affiliations

  1. Bauman Moscow State Technical University, Moscow, Russia

    A. L. Vorontsov

Authors
  1. A. L. Vorontsov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. L. Vorontsov.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Vorontsov, A.L. Production of Large Disks from Cylindrical Blanks by Plastic Deformation. 5. Comparison of Theoretical and Experimental Results. Russ. Engin. Res. 39, 843–847 (2019). https://doi.org/10.3103/S1068798X19100265

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X19100265

Keywords:

Search

Navigation