Abstract
Existing approaches to cutting are analyzed. The advantages and disadvantages of each model are considered in detail.
Similar content being viewed by others
References
Johnson, W. and Mellor, P.B., Engineering Plasticity, New York: Van Nostrand Reinhold, 1973.
Armarego, E.J.A. and Brown, R.H., The Machining of Metals, Englewood Cliffs, NJ: Prentice-Hall, 1969.
Kozhevnikov, D.V. and Kirsanov, D.V., Rezanie materialov (Cutting of Materials), Moscow: Mashinostroenie, 2007.
Petrushin, S.I. and Proskokov, A.V., Theory of constrained cutting: chip formation with a developed plastic-deformation zone, Russ. Eng. Res., 2010, vol. 30, no. 1, pp. 45–50.
Petrushin, S.I. and Proskokov, A.V., Theory of constrained cutting: Calculating the stress-strain state in the cutting zone, Russ. Eng. Res., 2010, vol. 30, no. 2, pp. 133–137.
Vorob’ev, I.A., Quasistatic model of the formation of the zone of primary deformation in the cutting of metals, Cand. Sci. (Eng.) Dissertation, Tula, 2010.
Arshinov, V.A., Rezanie metallov i rezhushchei instrument (Cutting of Metals and Cutting Tools), Moscow: Mashinostroenie, 1976.
Gorelov, V.M., Obrazovanie metallicheskoi struzhki (Formation of Metal Chip), Moscow: Mashgiz, 1962.
Vorontsov, A.L., Albagachiev, A.Yu., and Sultan-Zade, N.M., Teoreticheskie osnovy obrabotki metallov v mashinostroenii (Theoretical Basis of Metal Processing in Machine Engineering), Staryi Oskol: TNT, 2014.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting. 1. Introduction, Russ. Eng. Res., 2008, vol. 28, no. 1, pp. 48–59.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 2. A review of cutting theory, Russ. Eng. Res., 2008, vol. 28, no. 2, pp. 144–155.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting. 3. Current theory of failure with plastic deformation, Russ. Eng. Res., 2008, vol. 28, no. 3, pp. 243–250.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 4. General principles of a new theory of cutting, Russ. Eng. Res., 2008, vol. 28, no. 4, pp. 346–351.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 5. Determining the kinematic, stress, and strain states of the blank, Russ. Eng. Res., 2008, vol. 28, no. 5, pp. 461–471.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 6. Determining the basic parameters of cutting, Russ. Eng. Res., 2008, vol. 28, no. 6, pp. 571–578.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 7. Mathematical description of the formation of different chips, pulsation of the cutting force, and contact parameters of the machined billet surface and the rear cutter surface, Russ. Eng. Res., 2008, vol. 28, no. 7, pp. 674–680.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 8. Chip-breaker design, Russ. Eng. Res., 2008, vol. 28, no. 8, pp. 786–792.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 9. Practical calculations of cutting parameters in turning, Russ. Eng. Res., 2008, vol. 28, no. 9, pp. 878–888.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 10. Planing and broaching, Russ. Eng. Res., 2008, vol. 28, no. 10, pp. 984–986.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 11. Calculation of cylindrical-milling parameters, Russ. Eng. Res., 2008, vol. 28, no. 10, pp. 987–993.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 12. Calculation of complex-milling parameters, Russ. Eng. Res., 2008, vol. 28, no. 11, pp. 1104–1108.
Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 13. Calculation of end-milling parameters, Russ. Eng. Res., 2008, vol. 28, no. 12, pp. 1207–1216.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 1. Basic principles, Russ. Eng. Res., 2010, vol. 30, no. 1, pp. 64–66.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 2. Temperature distribution over the chip thickness, Russ. Eng. Res., 2010, vol. 30, no. 2, pp. 149–151.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 3. Influence of cutter’s front angle on the cutting temperature and influence of preheating of the blank on the cutting force, Russ. Eng. Res., 2010, vol. 30, no. 3, pp. 274–275.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 4. Analysis of the basic thermophysical theories of cutting (Part 1), Russ. Eng. Res., 2010, vol. 30, no. 4, pp. 381–384.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 4. Analysis of the basic thermophysical theories of cutting (Part 2), Russ. Eng. Res., 2010, vol. 30, no. 5, pp. 484–492.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 4. Analysis of the basic thermophysical theories of cutting (Part 3), Russ. Eng. Res., 2010, vol. 30, no. 6, pp. 604–610.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 4. Analysis of the basic thermophysical theories of cutting (Part 4), Russ. Eng. Res., 2010, vol. 30, no. 7, pp. 713–716.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 4. Analysis of the basic thermophysical theories of cutting (part 5), Russ. Eng. Res., 2010, vol. 30, no. 8, pp. 800–806.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 9. Analysis of the basic thermophysical theories of cutting (Part 6), Russ. Eng. Res., 2010, vol. 30, no. 9, pp. 921–927.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 10. Analysis of the basic thermophysical theories of cutting (part 7), Russ. Eng. Res., 2010, vol. 30, no. 10, pp. 1032–1035.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 11. Analysis of the basic thermophysical theories of cutting (Part 8), Russ. Eng. Res., 2010, vol. 30, no. 11, pp. 1141–1149.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 12. General mathematical apparatus of the thermophysics of cutting (Part 1), Russ. Eng. Res., 2010, vol. 30, no. 12, pp. 1241–1247.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 5. General mathematical apparatus of the thermophysics of cutting (Part 2), Russ. Eng. Res., 2011, vol. 31, no. 1, pp. 47–52.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 14. General mathematical apparatus of the thermophysics of cutting (Part 3), Russ. Eng. Res., 2011, vol. 31, no. 2, pp. 147–152.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 15. Determining the temperature fields and contact temperatures in cutting (part 1), Russ. Eng. Res., 2011, vol. 31, no. 3, pp. 258–263.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 16. Determining the temperature fields and contact temperatures in cutting (part 2), Russ. Eng. Res., 2011, vol. 31, no. 4, pp. 369–375.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 17. Determining the temperature fields and contact temperatures in cutting (Part 3), Russ. Eng. Res., 2011, vol. 31, no. 5, pp. 471–478.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 18. Determining the temperature fields and contact temperatures in cutting (part 1), Russ. Eng. Res., 2011, vol. 31, no. 6, pp. 574–581.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 19. Determining the temperature fields and contact temperatures in cutting (part 2), Russ. Eng. Res., 2011, vol. 31, no. 7, pp. 671–678.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 20. Examples of practical calculations of the cutting temperature (part 3), Russ. Eng. Res., 2011, vol. 31, no. 8, pp. 776–784.
Vorontsov, A.L., Sultan-Zade, N.M., Albagachiev, A.Yu., and Savkin, A.I., Development of a new theory of thermal cutting processes: 21. Determining optimal cutting conditions to extend tool life, Russ. Eng. Res., 2011, vol. 31, no. 9, pp. 877–879.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © A.N. Bol’shakov, 2018, published in Vestnik Mashinostroeniya, 2018, No. 3, pp. 70–76.
About this article
Cite this article
Bol’shakov, A.N. Theory of Intermittent Cutting. 2. Existing Approaches. Russ. Engin. Res. 38, 450–456 (2018). https://doi.org/10.3103/S1068798X18060059
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X18060059