Abstract
Refined and engineering methods of calculating threaded joints subjected to rupture force and a tipping torque are developed, in the case where the contact surface roughness of the flanges is Ra ≥ 1.25 μm, with more than 106 loading cycles.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Birger, I.A. and Iosilevich, G.B., Rez’bovye soedineniya (The Threaded Joints), Moscow: Mashinostroenie, 1973.
Chernavskii, S.A., Snesarev, G.A., Kozintsev, B.S., et al., Proektirovanie mekhanicheskikh peredach: uchebno-spravochnoe posobie dlya vuzov (Design of Mechanical Transmissions: Manual for Higher Education Institutions), Moscow: Mashinostroenie, 1984.
Dunaev, P.F. and Lelikov, O.P., Konstruirovanie uzlov i detalei mashin: uchebnoe posobie dlya stud tekhnicheskikh spetsial’nostei vuzov (Design of Machine Parts: Manual for Technical Higher Education Institutions), Moscow: Akademiya, 2004.
Ponomarev, R.N. and Ishmurzina, N.M., Emergency failures depending on the operation time of submersible centrifugal pumps, Neftegaz. Delo, 2006, vol. 4, no. 1, pp. 221–224.
Smirnov, N.I., Smirnov, N.N., and Mukhamadeev, K.G., Ways of improving working life for immersed centrifugal pumps, Chem. Petrol. Eng., 2000, vol. 36, nos. 3–4, pp. 152–156.
Ivanov, A.S. and Murkin, S.V., Raschet i proektirovanie rez’bovykh soedinenii privodov (Calculation and Design of the Threaded Joints of Drivers), Moscow: Innovatsionnoe Mashinostroenie, 2015.
Murkin, S.V., Ivanov, A.S., and Ermolaev, M.M., Theoretical and experimental study of a group of threaded joints affected by the tear force and overturning moment, Vestn. Mashinostr., 2014, no. 5, pp. 20–28.
Murkin, S.V., Ivanov, A.S., Ermolaev, M.M., Rudnev, S.K., and Kuts, M.S., Position of the skew axis of a threaded joint under the action of a tipping torque, Russ. Eng. Res., 2016, vol. 36, no. 1, pp. 16–19.
Ioselevich, G.B., Detali mashin: uchebnik dlya vuzov (Machine Parts: Manual for Higher Education Institutions), Moscow: Mashinostroenie, 1988.
Reshetov, D.N., Gusenkov, A.P., Drozdov, Yu.N., et al., Mashinostroenie. Entsiklopediya. Tom IV-1. Mashinostroenie. Detali mashin. Konstruktsionnaya prochnost’. Trenie, iznos, smazka (Machine Engineering: Encyclopedia, Vol. IV-1: Machine Engineering. Machine Parts. Construction Durability. Friction, Wearing, and Lubrication), Reshetov, D.N., Ed., Moscow: Mashinostroenie, 1994.
Faskhiev, Kh.A., Improvement of lifetime of the fastening studs of ball-units of the front axle of the car, Gruzovik, 2010, no. 8, pp. 30–36.
Pavlenko, P.D. and Talipova, I.P., The strength of the flange pins joints with crank cases of the car bridges, Vestn. Mashinostr., 2004, no. 6, pp. 21–22.
Kegelradgetriebemotoren 2K, Katalog 7. http://www.bockwoldt.de/downloads/produkte/Kegelradgetriebe/katalog_2k.pdf.
Ivanov, A.S., Smirnov, N.I., Murkin, S.V., and Ermolaev, M.M., Fatigue strength of screws in submersible centrifugal pumps under a tipping torque, Russ. Eng. Res., 2015, vol. 35, no. 10, pp. 724–728.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © A.S. Ivanov, S.V. Murkin, 2016, published in Vestnik Mashinostroeniya, 2016, No. 5, pp. 3–10.
About this article
Cite this article
Ivanov, A.S., Murkin, S.V. Threaded joints in drives. Russ. Engin. Res. 36, 611–619 (2016). https://doi.org/10.3103/S1068798X16080116
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X16080116