Abstract
A method for comprehensive assessment of the effectiveness of a cutting tool during its introduction into operation is presented. The method allows not using the monetary equivalent when normalizing the parameters; therefore, all the initial parameters are applied in their natural units of measurement. The obtained partial effects show the advantage of a prototype product in comparison with the base one in terms of a separate property. The combined effect gives the idea of the entire complex of the properties of the product under consideration.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Notes
The specific values of the parameters characterizing objects being assessed are taken as the base point *.
REFERENCES
Pukhal’skii, V.A., Resursosberegayushchaya sistema obespecheniya kachestva produktsii. Monografiya (Resource-Saving System of Product Quality Assurance), Moscow: Spektr, 2016.
Pukhal’skii, V.A., A combined method of product quality assessment, Nadezhnost’ Kontrol’ Kachestva. Metody Menedzhmenta Kachestva, 1999, no. 4, pp. 55–58.
Arsen’ev, Yu.D., Teoriya podobiya v inzhenernykh ekonomicheskikh raschetakh (Similarity Theory in Engineering Economic Calculations), Moscow: Vysshaya Shkola, 1967.
Silin, S.S., Metod podobiya pri rezanii materialov (Similarity Method in Cutting of Materials), Moscow: Mashinostroenie, 1979.
Vorontsov, A.L. and Albagachiev, A.Yu., and Sultan-zade, N.M., Teoreticheskie osnovy obrabotki metallov v mashinostroenii (Theoretical Foundations of Metal Processing in Machinery Manufacture), Staryi Oskol, Belgorod oblast: TNT, 2013.
Albagachiev, A.Yu., Kovalev, A.A., and Krasko, A.S., Selection of a method for strengthening treatment of machine parts in the conditions of automated small-batch production, Probl. Mashinostr. Avtom., 2021, no. 2, pp. 4–12. https://doi.org/10.52261/02346206_2021_2_4
Korzynski, M., Pacana, A., and Cwanek, J., Fatigue strength of chromium coated elements and possibility of its improvement with slide diamond burnishing, Surf. Coat. Technol., 2009, vol. 203, no. 12, pp. 1670–1676. https://doi.org/10.1016/j.surfcoat.2008.12.022
Korhonen, H., Laakkonen, J., Hakala, J., and Lappalainen, R., Improvements in the surface characteristics of stainless steel workpieces by burnishing with an amorphous diamond-coated tip, Mach. Sci. Technol., 2013, vol. 17, no. 4, pp. 593–610. https://doi.org/10.1080/10910344.2013.837351
Giasin, K., Hodzic, A., Phadnis, V., and Ayvar-Soberanis, S., Assessment of cutting forces and hole quality in drilling Al2024 aluminium alloy: Experimental and finite element study, Int. J. Adv. Manuf. Technol., 2016, vol. 87, nos. 5–8, pp. 2041–2061. https://doi.org/10.1007/s00170-016-8563-y
Serebrennikova, A., Nikolaeva, E., Savilov, A., Timofeev, S.A., and Pyatykh, A.S., Research results of stress-strain state of cutting tool when aviation materials turning, J. Phys.: Conf. Ser., 2018, vol. 944, p. 012104. https://doi.org/10.1088/1742-6596/944/1/012104
Kröger, W., Reliability of technical systems. http://webarchiv.ethz.ch/lsa/education/vorl/rts/06_RTS_common_cause.pdf.
Minor, D., Risk preferences and misconduct: Evidence from politicians, Business Research for Business Leaders. https://hbswk.hbs.edu/item/risk-preferences-and-misconduct-evidence-frompoliticians.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors declare no that they have no conflicts of interest.
Additional information
Translated by Sh. Galyaltdinov
About this article
Cite this article
Albagachiev, A.Y., Pukhal’skii, V.A. Analysis of the Peculiarities of Using the Combined Estimation Method. J. Mach. Manuf. Reliab. 51, 872–875 (2022). https://doi.org/10.3103/S1052618822080039
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1052618822080039