Abstract
For shaft–seal connections, the dependence is determined and an algorithm for calculating the total deviation from alignment and the total radial runout in the shaft–seal connection is tested. It is recommended that the designers of a manufactured gearbox increase the requirements on the dimensions of the parts forming the dimensional chain that determines the total deviation from alignment.
![](http://media.springernature.com/m312/springer-static/image/art%3A10.3103%2FS1052618821060066/MediaObjects/12001_2021_8258_Fig1_HTML.gif)
Similar content being viewed by others
REFERENCES
Leonov, O.A. and Shkaruba, N.Zh., Calculation of fit tolerance by the parametric joint failure model, J. Mach. Manuf. Reliab., 2020, vol. 49, no. 12, pp. 1027–1032. https://doi.org/10.3103/S1052618820120092
Li, Q., Yang, L., Zhao, W., Shi, Z., and Liu, Z., Design of positioning mechanism fit clearances based on on-orbit re-orientation accuracy, Appl. Sci., 2019, vol. 9, no. 21, p. 4712. https://doi.org/10.3390/app9214712
Leonov, O.A. and Shkaruba, N.Zh., A parametric failure model for the calculation of the fit tolerance of joints with clearance, J. Frict. Wear, 2019, vol. 40, no. 4, pp. 332–336. https://doi.org/10.3103/S1068366619040068
Bodunov, M.A., Bodunov, D.M., and Borodin, I.V., The flow of thin layer of plastic anisotropic material on the surface of elastic half-space, Izv. Mosk. Gos. Tekh. Univ. MAMI, 2013, vol. 3, no. 1, pp. 13–18.
Senin, P.V., Rakov, N.V., Smolyanov, A.V., and Makeikin, A.M., Theoretical analysis of dimension chains when restoring the landing socket for liner sleeve collar in the depth of the engines D-245 and D-260, Inzh. Tekhnol. Sist., 2020, vol. 30, no. 2, pp. 188–199. https://doi.org/10.15507/2658-4123.030.202002.188-199
Galkin, M.G. and Smagin, A.S., Features of analysis of technological dimensional chains by probabilistic method, Vestn. Mashinostr., 2016, no. 4, pp. 13–17.
Galkin, M.G. and Smagin, A.S., Probabilistic calculation of dimensional chains in predicting surface performance, Russ. Eng. Res., 2015, vol. 35, no. 3, pp. 177–180. https://doi.org/10.3103/S1068798X15030065
Bogutskii, V.B., Shron, L.B., Manuilenko, V.M., and Pyankovskaya, M.V., Dimensional analysis as a tool for ensuring operation characteristics of power tools, Izv. Tul. Gos. Univ. Tekh. Nauki, 2016, no. 8-2, pp. 64–70.
Bondareva, G.I., Leonov, O.A., Shkaruba, N.Zh., and Vergazova, Yu.G., Changes in the standard of unified system of tolerances and fits, Traktory Sel’khozmash., 2016, no. 12, pp. 39–42.
Leonov, O.A., Shkaruba, N.Zh., Vergazova, Yu.G., Golinitskiy, P.V., and Antonova, U.Yu., Quality control in the machining of cylinder liners at repair enterprises, Russ. Eng. Res., 2020, vol. 40, no. 9, pp. 726–731. https://doi.org/10.3103/S1068798X20090105
Dunaev, P.F. and Lelikov, O.P., Raschet dopuskov razmerov (Calculation of Dimensional Tolerances), Moscow: Mashinostroenie, 2016.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors declare that they have no conflicts of interest.
Additional information
Translated by E. Oborin
About this article
Cite this article
Erokhin, M.N., Leonov, O.A., Shkaruba, N.Z. et al. Application of Dimensional Analysis for Calculating the Total Misalignment between a Seal and a Shaft. J. Mach. Manuf. Reliab. 50, 524–529 (2021). https://doi.org/10.3103/S1052618821060066
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1052618821060066