Abstract
Several copper alloys with the addition of Zn and Sn are taken for the study. In order to determine the effect of severe plastic deformation (SPD) on microstructure formation, these alloys are subjected to severe plastic deformation on a Gleeble-3800 thermomechanical simulator. The study uses a special case of 3D forging—2D forging, using a MaxStrain multi-axis deformation module. Two modes are developed for processing: 10 deformation cycles (20 impacts) at room temperature with a total degree of deformation greater than 7; 20 deformation cycles (40 impacts) at room temperature with a total degree of deformation greater than 17. The results of the analysis of the microstructure of copper alloys after physical modeling are presented in the study.
This is a preview of subscription content, log in via an institution to check access.
REFERENCES
Rudskoy, A.I., Nanostrukturirovannye metallicheskie materialy (Nanostructured Metallic Materials), St. Petersburg: Nauka, 2011.
Rudskoy, A.I., Nanostructured metallic materials, Tsvetnye Met., 2014, no. 4, pp. 22–29.
Parshikov, R.A., Rudskoy, A.I., Zolotov, A.M., and Tolochko, O.V., Analysis of specimen plastic flow features during severe plastic deformation, Rev. Adv. Mater. Sci., 2016, vol. 45, nos. 1–2, pp. 67–75.
Rudskoy, A.I., Bogatov, A.A., Nukhov, D.Sh., and Tolkushkin, A.O., On the development of the new technology of severe plastic deformation in metal forming, Mater. Phys. Mech., 2018, vol. 38, no. 1, pp. 76–81.
Rudskoi, A.I., Zolotov, A.M., and Parshikov, R.A., Severe plastic deformation influence on engineering plasticity of copper, Mater. Phys. Mech., 2018, vol. 38, no. 1, pp. 64–68.
Rudskoy, A.I., Naumov, A.A., and Chernikov, E.V., Friction stir processing of metals is a new method of intensive plastic deformation, Tsvetnye Met., 2014, no. 4, pp. 36–40.
Kolbasnikov, N.G., Zotov, O.G., Duranichev, V.V., Naumov, A.A., Mishin, V.V., and Ringinen, D.A., The influence of the hot severe plastic deformation on microstructure and properties of low carbon steel, Metalloobrabotka, 2009, no. 4, pp. 25–31.
Musabirov, I.I., Safarov, I.M., Galeyev, R.M., Afonichev, D.D., Koledov, V.V., Rudskoi, A.I., and Mulyukov, R.R., Plastic deformation of the Ni–Mn–Ga alloy by multiple isothermal forging, Mater. Phys. Mech., 2017, vol. 33, no. 1, pp. 124–136.
Meyers, M.A., Mishra, A., and Benson, D.J., Mechanical properties of nanocrystalline materials, Prog. Mater. Sci., 2006, vol. 51, no. 4, pp. 427–556. https://doi.org/10.1016/j.pmatsci.2005.08.003
Rudskoy, A.I. and Kodzhaspirov, G.E., Ul’tramelkozernistye metallicheskie materialy (Ultrafine-Grained Metallic Materials), St. Petersburg: S.-Peterb. Gos. Politekh. Univ., 2015.
Funding
This work was supported by ongoing institutional funding. No additional grants to carry out or direct this particular research were obtained.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors of this work declare that they have no conflicts of interest.
Additional information
Translated by A.Kolemesin
Publisher’s Note.
Allerton Press remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Borisov, A.S., Naumov, A.A., Borisova, A.Y. et al. Effect of Severe Plastic Deformation on the Formation of the Nonferrous Metal Alloy Microstructure. Steel Transl. 53, 830–836 (2023). https://doi.org/10.3103/S0967091223100054
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S0967091223100054