Skip to main content
SpringerLink
Log in

Prospects for Manufacturing Friction Disks from Cold-Rolled Steel

  • Published:
Steel in Translation Aims and scope

Abstract

Assessment of the influence of design factors on the performance of friction disks is given. The necessity of reduction of warpage of disks and residual stresses in them is shown to increase the operational reliability of friction units of caterpillar and wheeled vehicles. The analysis of the achievable accuracy of manufacturing friction disks is carried out. The technology of manufacturing disks from cold-rolled steel C67S has been studied. To increase the operational reliability of disks, it is proposed to manufacture them using dynamic stabilization, which, while reducing technological costs, provides the specified accuracy of disks in terms of deviation from flatness, a decrease in residual stresses in them, and the tendency of disks to warp.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.
Fig. 7.

REFERENCES

  1. Zhuchkov, M., Korol’kov, R., and Petrov, O., Raschet dolgovechnosti transmissii voennykh gusenichnykh mashin (Longevity Analysis of the Drive Train of Military Tracked Vehicles), Isakov, I.I., Ed., Moscow: TsNII Informatsii, 1987.

  2. Truhanov, V.M., Kryhtin, Yu.F., Krykhtin, Yu.I., and Zheltobryukhov, V.F., Transmissii gusenichnykh i kolesnykh mashin (Drive Trains of Tracked and Wheeled Vehicles), Moscow: Mashinostroenie, 2001.

  3. Antonyuk, V.E., Features of the design and manufacturing techniques of frictional disks of caterpillar and wheel cars, Mekh. Mash., Mekh. Mater., 2016, no. 3, pp. 43–52.

  4. Gupalov, B.A. and Zakuraev, V.V., The analysis of the reasons for loss of geometric accuracy in friction disks, Omskii Nauchn. Vestn., 2012, no. 3, pp. 146–150.

  5. Germanchuk, F.K., Dolgovechnost’ i effektivnost’ tormoznykh ustroistv (Longevity and Efficiency of Braking Devices), Moscow: Mashinostroenie, 1973.

  6. Konoreev, R.V., Malyshko, A.A., and Konovodov, V.V., Method for restoration of friction disks, RF Patent 2210477, 2003.

  7. Konoreev, R.V., Improvement of the technology for restoring disks of friction drives by gas-detonation sputtering (one example of K-700 tractor), Extended Abstract of Cand. Sci. (Eng.) Dissertation, Novosibirsk: Novosibirsk State Agrarian Univ., 2007.

  8. Antonyuk, V.E., Goman, A.M., Zabolotskii, M.M., and Rudyi, V.V., Assessment of the power capacity and heat loading of a multidisk oil-cooled brake, J. Frict. Wear, 2009, vol. 30, no. 5, pp. 329–336. https://doi.org/10.3103/s1068366609050055

    Article  Google Scholar 

  9. Antonyuk, V.E., Design and operation features of friction discs, Mekh. Mash., Mekh. Mater., 2022, no. 2, pp. 40–47. https://doi.org/10.46864/1995-0470-2022-2-59-39-46

  10. Antonyuk, V.E. and Sandomirskii, S.G., Residual stresses in friction disks: Causes of appearance, consequences, diagnostics, and elimination, Aktual’nye voprosy mashinovedeniya. Sb. nauch. tr. (Topical Issues of Mechanical Engineering: Collection of Sci. Papers), Minsk: Ob’’edin. Inst. Mashinostroeniya Nats. Akad. Nauk Belarusi, 2022, vol. 11, pp. 159–159.

    Google Scholar 

  11. Hoerbiger Lamellenhandbuch, Schongau, Germany: Hoerbiger Antriebstechnik, 2004.

  12. Reibbeldge, Miba Frictec Gmb, H., 2023. http://www.miba.com/Reibbelaege,4,de.html. Cited January 3, 2023.

  13. Antonyuk, V.E., Goman, A.M., and Rudyi, V.V., Effect of relative width of friction disks on their operational indicators, Materialy, tekhnologiya i oborudovanie v proizvodstve, remonte i modernizatsii mashin. Sb. nauch. tr. VII mezhdunar. nauch.-tekhn. konf. (Materials, Technologies, and Equipment in Manufacture, Repair, and Modernization of Machines: Proc. 7th Int. Sci.-Tech. Conf.), 2009, vol. 2, pp. 133–136.

  14. Antonyuk, V.E., Dinamicheskaya stabilizatsiya v proizvodstve malozhestkikh detalei (Dynamic Stabilization in Manufacture of Low-Stiffness Machine Elements), Minsk: Belaruskaya Navuka, 2017.

  15. Rudyi, V.V., Calculation-experimental justification of the parameters of oil-cooled braking disks in quarry lorries and equipment for their dynamic stabilization, Extended Abstract of Cand. Sci. (Eng.) Dissertation, Minsk: 2012.

  16. Antonyuk, V.E., Sidorenko, A.G., Zabolotskii, M.M., and Rudyi, V.V., Technology for manufacturing disks from cold-rolled steel for multidisk oil-cooled brakes, Aktual’nye voprosy mashinovedeniya. Sb. nauchn. tr. (Topical Issues of Mechanical Engineering: Collection of Sci. Papers), Minsk: Ob’’edin. Inst. Mashinostroeniya Nats. Akad. Nauk Belarusi, vol. 4, pp. 365–369.

  17. Active worldwide for our customers as the global technology leader, Waelzholz, https://www.waelzholz. com/en/company.html. Cited January 3, 2023.

  18. Antonyuk, V.E., Sidorenko, A.G., Sandomirskii, S.G., and Solomina, A.V., Analysis of the effect of the technology for manufacturing friction disks on the uniformity of their magnetic properties, Aktual’nye voprosy mashinovedeniya. Sb. nauchn. tr. (Topical Issues of Mechanical Engineering: Collection of Sci. Papers), Minsk: Ob’’edin. Inst. Mashinostroeniya Nats. Akad. Nauk Belarusi, 2015, vol. 4, pp. 363–364.

    Google Scholar 

  19. Antonyuk, V.E. and Sandomirskii, S.G., Analysis of uniformity of distribution of magnetic properties in thin-walled disks for predicting their shape stability, KhKhII Vseros. konf. po nerazrushayushchemu kontrolyu i tekhnicheskoi diagnostike Transformatsiya nerazrushayushchego kontrolya i tekhnicheskoi diagnostiki v epokhu tsifrovizatsii. Obespechenie bezopasnosti obshchestva v izmenyayushchemsya mire. Sb. trudov (22nd All-Russian Conf. on Nondestructive Testing and Technical Diagnostics Transformation of Nondestructive Testing and Technical Diagnostics in Digitalization Era: Ensuring the Safety of Society in the Changing World: Collection of Papers), Moscow: Spektr, 2020, pp. 141–144.

Download references

Funding

This work was supported by ongoing institutional funding. No additional grants to carry out or direct this particular research were obtained.

Author information

Authors and Affiliations

  1. Joint Institute of Mechanical Engineering, National Academy of Sciences of Belarus, Minsk, Republic of Belarus

    V. E. Antonyuk & S. G. Sandomirski

  2. Belarusian Automobile Plant, Zhodino, Republic of Belarus

    V. V. Rudyi

Authors
  1. V. E. Antonyuk
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. G. Sandomirski
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. V. V. Rudyi
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S. G. Sandomirski.

Ethics declarations

The authors of this work declare that they have no conflicts of interest.

Additional information

Translated by Sh. Galyaltdinov

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Antonyuk, V.E., Sandomirski, S.G. & Rudyi, V.V. Prospects for Manufacturing Friction Disks from Cold-Rolled Steel. Steel Transl. 53, 694–700 (2023). https://doi.org/10.3103/S0967091223080028

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S0967091223080028

Keywords:

Search

Navigation