Abstract
The sources of defects associated with stability loss of cold-rolled strip coils are established. The influence of the winding-drum structure in cold-rolling mills on the stress–strain state of the coils, both before and after removal from the winding system, is analyzed in detail. The possibility of modifying the stress–strain state of the coils by regulating the rigidity of the winding drum is considered. Recommendations are made regarding the selection of the winding technology for rolled strip.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Mazur, V.L. and Timoshenko, V.I., Stress-deformation state of cold-rolled coils, Izv. Vyssh. Uchebn. Zaved., Chern. Metall., 1979, no. 6, pp. 52–59.
Mazur, V.L. and Timoshenko, V.I., Computation of the stressed state of rolled paper cylinders, Mech. Compos. Mater., 1983, vol. 18, no. 5, pp. 598–603.
Mazur, V.L., Proizvodstvo lista s vysokokachestvennoi poverkhnost’yu (Production of Sheet with High Surface Quality), Kiev: Tekhnika, 1982.
Solov’ev, P.I., Dunaevskii, V.I., and Dornostup, V.S., Analysis of coiling drums of cold rolling mills, Tr. Vseross. Nauchno-Issled. Proektn.-Konstr. Inst. Metall. Mashinostr., 1962, no. 6, pp. 54–87.
Pawelski, O., Rasp, W., and Martin, G., Origin of sticker marks on batch-annealed cold-rolled sheet, Stahl Eisen, 1989, vol. 109, no. 4, pp. 174–184.
Prikhod’ko, I.Yu., Chernov, P.P., Timoshenko, V.I., and Akishin, V.V., Optimization of temperature and stress-strain of coils during cold rolling and bell annealing using digital models, Trudy pyatogo kongressa prokatchikov, g. Cherepovets, 21–24 oktyabrya 2003 g. (Proc. Fifth Congr. of Operators of Rolling Mills, Cherepovets, October 21–24, 2003), Moscow: Chermetinformatsiya, 2004, pp. 124–127.
Prikhod’ko, I.Yu., Timoshenko, V.I., Chernov, P.P., et al., The effect of roughness surface of cold-rolled strips on adhesion conditions of coils during annealing and the formation of surface defects, Metall. Gornorudn. Prom-st, 2002, nos. 8–9, pp. 92–101.
Wendt, P., Frech, W., and Leifgen, U., Cold rolling defect, “stickers” and countermeasures, Heat Process., 2007, vol. 2, pp. 127–135.
Yanabe, S., Takahashi, K., and Yamashita, T., Web winding simulation and wound roll stresses, J. Adv. Mech. Des., Syst., Manuf., 2010, vol. 4, no. 1, pp. 281–289.
Yuen, W.Y.D. and Cozijnsen, M., Optimum tension profiles to prevent coil collapses, SEAISI 2000 Australia Conf. on Improving the Cost Competitiveness of the Iron and Steel Industry, Shah Alam: South East Asia Iron Steel Inst., 2000, vol. 2, pp. 1/1–1/10.
Weiss, M., Abeyrathna, B., Rolfe, B., et al., Effect of coil set shape defects in roll forming steel strip, J. Manuf. Process., 2017, vol. 25, pp. 8–15.
Park, Y.H., Park, K., Won, S.Y., et al., Stress analysis model of strip winding system with a sleeve for a coil of thin stainless steel, J. Iron Steel Res. Int., 2017, vol. 24, pp. 1–7.
Xing, J., Geng, P., and Yang, T., Stress and deformation of multiple winding angle hybrid filament-wound thick cylinder under axial loading and internal and external pressure, Compos. Struct., 2015, vol. 131, pp. 868–877.
Lee, J. and Lee, C., An advanced model for the numerical analysis of the radial stress in center-wound rolls, Int. J. Mech. Sci., 2016, vol. 105, pp. 360–368.
Mazur, V.L., Production of cold-rolled steel coils, Steel Transl., 2011, vol. 41, no. 9, pp. 756–760.
Edwards, W.J. and Boulton, G., The Mystery of Coil Winding, Warrendale: Assoc. Iron Steel Eng., 2001, pp. 24–33.
Wang, Y., Li, L., Yan, X., et al., Modeling of stress distribution during strip coiling process, J. Iron Steel Res. Int., 2012, vol. 19, no. 8, pp. 6–11.
Mazur, V.L., Preventing surface defects in the uncoiling of thin steel sheet, Steel Transl., 2015, vol. 45, no. 12, pp. 959–966.
Mazur, V.L. and Pargamonov, E.A., Formation and prevention of flexure defects at the surface of coldrolled steel strip, Steel Transl., 2016, vol. 46, no. 8, pp. 595–601.
Mazur, V.L. and Nogovitsyn, A.V., Theory and Technology of Thin Sheet Rolling: Numerical Engineering Analysis and Applications, Boca Raton: CRC Press, 2018. http://www.crcpress.com; http://www.cips-publishing. com.
Turley, J.W., Sendzimir controlled collapse winder, Iron Steel Eng., 1974, vol. 51, no. 42, pp. 42–53.
Ataide, A.C., de Oliveria, F.C., de Melo, A.E., et al., Desenvolvimento de uma metodologia para medição do atrio entre tira e mandril da bobinadeira de laminador Sendzimir, Metal. Mater. Rev. Esc. Minas., 2011, vol. 64, no. 3, pp. 335–339.
Brivmanis, R.E and Gaganova, A.K., Namotochnye konstruktsii v elektricheskikh mashinakh i apparatakh (Winding Units in Electric Machines), Moscow: Energiya, 1971.
Feodos’ev, V.I., Soprotivlenie materialov (Strength of Materials), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 1999.
Mazur, V.L. and Timoshenko, V.I., Teoriya i tekhnologiya prokatki (gidrodinamicheskie effekty smazki i mikrorel’ef poverkhnosti) (Theory and Technology of Rolling: Hydrodynamic Effect of Lubrication and Surface Microrelief), Kyiv: ADEF-Ukraina, 2018.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © V.L. Mazur, V.I. Timoshenko, I.Yu. Prikhod’ko, 2018, published in Stal’, 2018, No. 8, pp. 19–26.
About this article
Cite this article
Mazur, V.L., Timoshenko, V.I. & Prikhod’ko, I.Y. Regulating the Coil Stress by Adjusting the Rigidity of the Winding Drum. Steel Transl. 48, 528–535 (2018). https://doi.org/10.3103/S0967091218080090
Received:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S0967091218080090