Abstract
The fire behavior of a structural masonry building has a positive relationship with the behavior of its constituent materials under high temperatures. Assessing the residual mechanical strength of the structural masonry components is essential, following the exposure to high temperatures. This work proposes to examine the standard for the determination of the mechanical properties (compressive strength and elastic modulus) of concrete blocks under high temperatures. Based on the existing recommendations (RILEM Technical Committee in Mater Struct 40: 841–853, 2007. 10.1617/s11527-007-9285-2, Mater Struct 40: 855–864, 2007. 10.1617/s11527-007-9286-1, Mater Struct 28: 410–414, 1995, Mater Struct 33: 219–223, 2000, Mater Struct 37: 139–144, 2004. 10.1007/bf02486610, Mater Struct 30: 17–21, 1997. 10.1007/bf02539270, Mater Struct 31: 290–295, 1998, Mater Struct 33: 6–13, 2000, Mater Struct 33: 224–228, 2000, Mater Struct 38: 913–919, 2005. 10.1617/14363RILEM Technical Committee (2007), Recommendation of RILEM TC 200-HTC in Mater Struct 40: 449–458, 2007. 10.1617/s11527-006-9203-z), an extensive experimental program was proposed to guide the adaptation of these recommendations to the case of concrete blocks, with emphasis on the heating and cooling rate of the samples. Suggestions of parameters necessary for laboratory evaluation of residual mechanical strength at elevated temperatures are presented for the hollow concrete block (HCB): number of specimens, testing age, storage conditions, rate of temperature rise with the time for heating the samples, suggestions of internal instrumentation of the equipment for the effective control of this rate and guaranteeing uniformity of heating.
Similar content being viewed by others
References
RILEM Technical Committee (2007) Recommendation of RILEM TC 200-HTC: mechanical concrete properties at high temperatures-modelling and applications part 1: introduction-general presentation. Mater Struct 40:841–853. https://doi.org/10.1617/s11527-007-9285-2
RILEM Technical Committee (2007) Recommendation of RILEM TC 200-HTC: mechanical concrete properties at high temperatures-modelling and applications Part 2: Stress-strain relation. Mater Struct 40:855–864. https://doi.org/10.1617/s11527-007-9286-1
RILEM Technical Committee (1995) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 3: compressive strength for service and accident conditions. Mater Struct 28:410–414
RILEM Technical Committee (2000) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 4: tensile strength for service and accident conditions. Mater Struct 33:219–223
RILEM Technical Committee (2004) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 5: modulus of elasticity for service and accident conditions. Mater Struct 37:139–144. https://doi.org/10.1007/bf02486610
RILEM Technical Committee (1997) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 6: thermal strain. Mater Struct 30:17–21. https://doi.org/10.1007/bf02539270
RILEM Technical Committee (1998) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 7: transient creep for service and accident conditions. Mater Struct 31:290–295
RILEM Technical Committee (2000) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 8: steady-state creep and creep recovery for service and accident conditions. Mater Struct 33:6–13
RILEM Technical Committee (2000) RILEM TC 129-MHT: test methods for mechanical properties of concrete at high temperatures - part 9: shrinkage for service and accident conditions. Mater Struct 33:224–228
RILEM Technical Committee (2005) Recommendation of RILEM TC 200-HTC: mechanical concrete properties at high temperatures-Modelling and applications Part 10: Restraint stress. Mater Struct 38:913–919. https://doi.org/10.1617/14363RILEMTechnicalCommittee(2007)
Recommendation of RILEM TC 200-HTC (2007) mechanical concrete properties at high temperatures-modelling and application part 11: relaxation. Mater Struct 40:449–458. https://doi.org/10.1617/s11527-006-9203-z
Harmathy TZ, Allen LW (1972) Thermal performance of concrete masonry walls in fire. Fire Technol 8:142–148. https://doi.org/10.1007/BF02590578
Harmathy TZ, Allen LW (1973) Thermal properties of selected masonry unit concretes. ACI Mater J 70:132–142. doi: https://doi.org/10.14359/11193
Ayala FRR (2010) Mechanical properties and structural behaviour of masonry at elevated temperatures. Univ Manchester, Fac Engeneering Phys Sci PhD Civil:294
Russo S, Sciarretta F (2013) Masonry exposed to high temperatures: mechanical behaviour and properties - an overview. Fire Saf J 55:69–86. https://doi.org/10.1016/j.firesaf.2012.10.001
Andreini M, Caciolai M, La Mendola S et al (2015) Mechanical behavior of masonry materials at high temperatures. Fire Mater 39:41–57. https://doi.org/10.1002/fam.2229
Neville AM (2016) Propriedades do Concreto, 5th ed. Bookman, Porto Alegre
Kodur VKR, Harmathy TZ (2016) Properties of building materials. In: Hurley M, Gottuk D, Hall JHarada K, et al (eds) SFPE handbook of fire protection engineering, 5th edn. Springer, New York, pp 277–324
Naser MZ (2019) Properties and material models for common construction materials at elevated temperatures. Constr Build Mater 215:192–206. https://doi.org/10.1016/j.conbuildmat.2019.04.182
Pope H, Zalok E (2019) The effect of fire temperatures on the mechanical performance of concrete masonry materials. 13th North American Masonry Conference. TMS, Salt Lake City, pp 252–264
Pope H, Zalok E (2020) Geometry Effects on the Fire Resistance Rating of Masonry. Mason Soc 38:122
American Society for Testing and Materials (2016) ASTM C90–16a: standard specification for loadbearing concrete masonry units
European Committee for Standardization (2011) EN 771–3: Specification for masonry units - part 3: aggregate concrete masonry units. Brussels
Associação Brasileira de Normas Técnicas (2013) ABNT NBR 12118: Blocos vazados de concreto simples para alvenaria - métodos de ensaio. Rio de Janeiro
American Society for Testing and Materials (2021) ASTM C140/C140M: standard test methods for sampling and testing concrete masonry units and related units
European Committee for Standardization (2011) EN 772–1: Methods of test for masonry units - part 1: determination of compressive strength. Blussels
Associação Brasileira de Normas Técnicas (2020) ABNT NBR 16868–3: Alvenaria Estrutural - Parte 3: Métodos de ensaio. Rio de Janeiro
Parsekian GA, Christoforo AL, Mazzú ADE, Dalfré GM (2021) Humidity and specimen preparation procedure: influence on compressive strength of concrete blocks. Rev IBRACON Estruturas e Mater 14:1–10. https://doi.org/10.1590/s1983-41952021000200010
Canadian Standards Association (2014) CS S304: Design of masonry structures. CSA Group
Kleeman PW, Page AW (1989) A study of the in-situ properties of capping materials used in compression tests. Report 040.06.1989. Dept of Civil Engineering & Surveying, Newcastle
Kleeman PW, Page AW (1990) The in-situ properties of packing materials used in compression tests. Mason Int 4:68–74
Page AW, Kleeman PW (1991) The influence of capping material and platen restraint on the failure of hollow masonry units and prisms. In: Proceedings of the Ninth International Brick & Block Masonry Conference. Berlim, pp 662–670
Fortes ES, Pereira IP, Parsekian GA, et al (2013) Evaluating the possibility of using dry materials to replace cement paste capping on concrete block testing. In: 12th Canadian Masonry Symposium. 12th CMS, Vancouver, pp 4–10
Souza AAA, Moreno JRAL (2010) The effect of high temperatures on concrete compression strength, tensile strength and deformation modulus. Rev IBRACON Estruturas e Mater 3:432–448. https://doi.org/10.1590/s1983-41952010000400005
Mehta PK, Monteiro PJM (2014) Concrete: microstructure, properties, and materials, 4th edn. McGraw-Hill Education, New York
American Society for Testing and Materials (2021) ASTM C150/C150M-21: Standard specification for portland cement
Acknowledgements
The authors would like to thank the São Paulo Research Foundation (FAPESP) by the support in the Project No.: 2018/19748-9.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Medeiros, W.A., Parsekian, G.A. & Moreno, A.L. Test methodology for determining the mechanical properties of concrete blocks at high temperatures. Mater Struct 55, 61 (2022). https://doi.org/10.1617/s11527-022-01892-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1617/s11527-022-01892-1