Abstract
This review surveys the phenomenon of plastic instabilities occurring in depth-sensing indentation measurements. Investigations presented focus on the characterization of Portevin–Le Châtelier type instabilities observed in different metal alloys during indentation. The effect of some important factors such as solute concentration, the formation of Guinier–Preston zones, and grain size and orientation are described and discussed. The phenomenon of plastic instabilities as serrated flow recently observed in bulk metallic glasses is also briefly reviewed.
Similar content being viewed by others
References
B.R. Lawn and V.R. Howes, J. Mater. Sci. 16, 2745 (1981).
M. Sakai, Acta Metall. Mater. 41, 1751 (1993).
R.F. Cook and G.M. Pharr, J. Hard. Mater. 5, 179 (1994).
A.E. Giannakopoulos, P.L. Larsson, and R. Vestergaard, Int. J. Solids Struct. 31, 2679 (1994).
P.L. Larsson, A.E. Giannakopoulos, E. Söderlund, E. Rowcliffe, and R. Vestergaard, Int. J. Solids Struct. 33, 221 (1996).
Y.T. Cheng and C.M. Cheng, Appl. Phys. Lett. 73, 614 (1998).
T.A. Venkatesh, K.J. Van Vliet, A.E. Giannakopoulos, and S. Suresh, Scr. Mater. 42, 833 (2000).
J.B. Pethica, R. Hutchings, and W.C. Oliver, Philos. Mag. A 48, 593 (1983).
M. Atkinson, J. Mater. Res. 10, 2908 (1995).
J. Mencik and M.V. Swain, J. Mater. Res. 10, 1491 (1995).
W.D. Nix and H. Gao, J. Mech. Phys. Solids 46, 411 (1988).
L.G. Hector and S.R. Schmid, Wear 215, 247 (1998).
S.R. Schmid and L.G. Hector, Wear 215, 257 (1998).
K. Zeng and C-h. Chiu, Acta Mater. 49, 3539 (2001).
A. Krell and S. Schadlich, Mater. Sci. Eng. A 307, 172 (2001).
N.Q. Chinh, F. Csikor, Zs. Kovács, and J. Lendvai, J. Mater. Res. 15, 1037 (2000).
X. Ma, F. Yoshida, and K. Shinbata, Mater. Sci. Eng. A 344, 296 (2003).
F. Fröhlich, P. Grau, and W. Grellmann, Phys. Status Solidi (a) 42, 79 (1977).
J. Gubicza, A. Juhász, P. Tasnádi, P. Arató, and G. Vörös, J. Mater. Sci. 31, 3109 (1996).
J. Gubicza, A. Juhász, and J. Lendvai, J. Mater. Res. 11, 2964 (1996).
J. Gubicza, A. Juhász, P. Arató, P. Szommer, P. Tasnádi, and G. Vörös, J. Mater. Sci. Lett. 15, 2141 (1996).
G.M. Pharr, W.C. Oliver, and F.R. Brotzen, J. Mater. Res. 7, 613 (1992).
W.C. Oliver and G.M. Pharr, J. Mater. Res. 7, 1564 (1992).
F.R. Brotzen, Int. Mater. Rev. 39, 24 (1994).
W.J. Pool, M.F. Ashby, and N.A. Fleck, Scr. Mater. 34, 559 (1996).
J.L. Bucaille, S. Stauss, E. Felder, and J. Michler, Acta Mater. 51, 1663 (2003).
Z. Li, Y.T. Cheng, H.T. Yang, and S. Chandrasekar, Surf. Coat. Technol. 154, 124 (2002).
B. Wolf, M. Swain, M. Kempf, and P. Paufler, J. Mater. Sci. 35, 723 (2000).
G.M. Pharr, W.C. Oliver, and D.R. Clarke, Scr. Metall. 23, 1949 (1989).
D.S. Stone and K.B. Yoder, J. Mater. Res. 9, 2524 (1994).
S.V. Hainsworth, M.R. McGurk, and T.F. Page, Surf. Coat. Technol. 102, 97 (1998).
E.G. Berasategui and T.F. Page, Surf. Coat. Technol. 163–164, 491 (2003).
G. Bérces, N.Q. Chinh, A. Juhász, and J. Lendvai, Acta Mater. 46, 2029 (1998).
G. Bérces, N.Q. Chinh, A. Juhász, and J. Lendvai, J. Mater. Res. 13, 1411 (1998).
N.Q. Chinh, G. Németh, A. Fekete, and J. Lendvai, Alum. Alloys 2, 621 (1998).
N.Q. Chinh, F. Csikor, Gy. Bérces, and J. Lendvai, Alum. Alloys 2, 979 (1998).
N.Q. Chinh, F. Csikor, and J. Lendvai, Mater. Sci. Forum 331–337, 1007 (2000).
Zs. Kovács, N.Q. Chinh, and J. Lendvai, J. Mater. Res. 16, 1171 (2001).
N.Q. Chinh, Gy. Horváth, Zs. Kovács, and J. Lendvai, Mater. Sci. Eng. A 324, 219 (2002).
Zs. Kovács, N.Q. Chinh, J. Lendvai, and G. Vörös, Mater. Sci. Eng. A 325, 255 (2002).
Zs. Kovács, N.Q. Chinh, J. Lendvai, Z. Horita, and T.G. Langdon, Mater. Sci. Forum 396–402, 1073 (2002).
Zs. Kovács, D. Fátay, K. Nyilas, and J. Lendvai, J. Eng. Mater. Technol. 124, 23 (2002).
H. Neuhäuser and C. Schwink, in Materials Science and Technology, edited by H. Mughrabi (VCH, Weinheim, Germany, 1993), Vol. 6, p. 191.
Y.J.M. Bréchet, Key Eng. Mater., 103, 21 (1995).
P.G. McCormick, Scr. Metall. 15, 441 (1982).
D. Thevenet, M. Mliha-Touati, and A. Zeghloul, Mater. Sci. Eng. A 266, 175 (1999).
P. Penning, Acta Metall. 20, 1169 (1972).
P.G. McCormick, Acta Metall. 20, 351 (1972).
L.P. Kubin and Y. Estrin, Acta Metall. 38, 697 (1990).
Y. Bréchet and Y. Estrin, Acta Metall. 43, 955 (1995).
S. Kok, M.S. Bharathi, A.J. Beaudoin, C. Fressengeas, G. Ananthakrishna, L.P. Kubin, and M. Lebyodkin, Acta Mater. 51, 3651 (2003).
R. Král, P. Lukác̆, and M. Janec̆ek, Mater. Sci. Forum 217–222, 1025 (1996).
E. Pink and A. Grinberg, Acta Metall. 30, 2153 (1982).
A.H. Cottrell, Philos. Mag. 44, 829 (1953).
A. Van den Beukel, Phys. Status Solidi (a) 30, 197 (1975).
J.M. Robinson and M.P. Shaw, Int. Mater. Rev. 39, 113 (1994).
J.M. Robinson, Int. Mater. Rev. 39, 217 (1994).
L.P. Kubin, K. Chihab, and Y. Estrin, Acta Metall. 36, 2707 (1988).
P.G. McCormick, S. Venkadesan, and C.P. Ling, Scr. Metall. 29, 1159 (1993).
P.G. McCormick and C.P. Ling, Acta Metall. Mater. 43, 1969 (1995).
P. Lukác̆, J. Balík, and F. Chmelík, Mater. Sci. Eng. A 234–236, 45 (1997).
H.M. Zbib and E.C. Aifantis, Scripta Metall. 22, 1331 (1988).
P. Ha¨hner, Mater. Sci. Eng. A 164, 23 (1993).
P.G. McCormick, Acta Metall. 30, 2079 (1982).
C.A. Schuh and T.G. Nieh, Acta Mater. 51, 87 (2003).
M.S. Bobji and S.K. Biswas, in Recent Advances in Metallurgical Processes, edited by D.H. Sastry, E.S. Dwarakadasa, G.N.K. Iyengar, and S. Subramanian, (New Age Int. Publishers, New Delhi, 1977), p. 1223.
W.H. Poisl, W.C. Oliver, and B.D. Fabes, J. Mater. Res. 10, 2024 (1995).
R. Král and P. Lukác̆, Mater. Sci. Eng. A 234–236, 786 (1997).
R.W. Cahn, Physical Metallurgy (American Elsevier Publishing Co. Inc., New York, 1970).
E. Pink, Acta Metall. 37, 1773 (1989).
A. Kalk, A. Nortmann, and Ch. Schwink, Philos. Mag. A 72, 1239 (1995).
Y. Iwahashi, J. Wang, Z. Horita, M. Nemoto, and T.G. Langdon, Scr. Mater. 35, 143 (1996).
M. Furukawa, Y. Iwahashi, Z. Horita, M. Nemoto, and T.G. Langdon, Mater. Sci. Eng. A 257, 328 (1998).
M. Furukawa, Z. Horita, M. Nemoto, and T.G. Langdon, J. Mater. Sci. 36, 2835 (2001).
M. Dao, N. Chollacoop, K.J. Van Vliet, T.A. Venkatesh, and S. Suresh, Acta Mater. 49, 3899 (2001).
R. Vaidyanathan, M. Dao, G. Ravichandran, and S. Suresh, Acta Mater. 49, 3781 (2001).
D. Tabor, Microindentation Techniques in Materials Science and Engineering, ASTM STP 889, edited by P.J. Blau and B.R. Lawn (American Society for Testing and Materials, Philadelphia, PA, 1986), p. 129.
W.J. Wright, R. Saha, and W.D. Nix, Mater. Trans. JIM 42, 642 (2001).
J.J. Kim, Y. Choi, S. Suresh, and A.S. Argon, Science 295, 654 (2002).
Y.I. Golovin, V.I. Ivolgin, V.A. Khonik, K. Kitagawa, and A.I. Tyurin, Scr. Mater. 45, 947 (2001).
C.A. Schuh, T.G. Nieh, and Y. Kawamura, J. Mater. Res. 17, 1651 (2002).
T.G. Nieh, C.A. Schuh, J. Wadsworth, and Y. Li, Intermetallics 10, 1177 (2002).
T. Benameur, K. Hajlaoui, A.R. Yavari, A. Inoue, and B. Rezgui, Mater. Trans. JIM 43, 2617 (2002).
W.H. Jiang and M. Atzmon, J. Mater. Res. 18, 75 (2003).
A. Gouldstone, H.J. Koh, K.Y. Zeng, A.E. Giannakopoulos, and S. Suresh, Acta Mater. 48, 2277 (2000).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Chinh, N.Q., Gubicza, J., Kovács, Z. et al. Depth-sensing indentation tests in studying plastic instabilities. Journal of Materials Research 19, 31–45 (2004). https://doi.org/10.1557/jmr.2004.19.1.31
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/jmr.2004.19.1.31