Abstract
Processing-induced residual stresses play an important role in the production and performance of thermally sprayed coatings. Their precise determination is a key to influence the coating properties by modification of process variables and to understand the processing-structure-property relationship. Among various methods for residual stress measurement, x-ray diffraction holds a specific position as being non-destructive, phase distinctive, localized, and applicable for real parts. The sin2 ω methods is commonly applied for bulk materials as well as coatings. However, the results are often reported without sufficient experimental details and the method is used in its simplified form without justification of certain assumptions.
In this investigation, the sin2 ω x-ray diffraction method was used to measure residual macrostress in plasma sprayed metallic (nickel, NiCrAlY, and molybdenum) and ceramic (ZrO2 + 8% Y2O3) coatings. Reproducibility of the method was tested and the assumptions allowing its use are discussed and experimentally verified. For nickel coatings, a comparison with hole drilling and neutron diffraction measurements is presented. The influence of processing factors such as deposition temperature and coating thickness is studied and the results are discussed.
Similar content being viewed by others
References
T.W. Clyne and S.C. Gill, Residual Stresses in Thermally Sprayed Coatings and Their Effect on Interfacial Adhesion—A Review of Recent Work, J. Therm. Spray Technol., Vol 5 (No. 4), 1996, p 401–418
V. Dolhof, J. Musil, M. Cepera, and J. Zeman, Stress Analysis of Thermal Sprayed Coatings Using a Semi-Destrutive Hole-Drilling Strain Gauge Method, Thermal Spray Science and Technology, C.C. Berndt and S. Sampath, Ed., ASM International, 1995, p 445–449
D.J. Greving, E.F. Rybicki, and J.R. Shadley, Effects of Coating Thickness and Residual Stresses on Bond Strength of C633-79 Thermal Spray Coating Test Specimens, Thermal Spray Industrial Applications, C.C. Berndt and S. Sampath, Ed., ASM International, 1994, p 647–653
E.F. Rybicki, J.R. Shadley, Y. Xiong, and D.J. Greving, In Situ Evaluation of Young’s Modulus and Poisson’s Ratio Using a Cantilever Beam Specimen, Thermal Spray Science and Technology, C.C. Berndt and S. Sampath, Ed., ASM International, 1995, p 409–414
X. Provot, H. Burlet, M. Vardavoulias, M. Jeandin, C. Richard, J. Lu, and D. Manesse, Comparative Studies of Microstructures, Residual Stress Distributions and Wear Properties for HVOF and APS WC-Co Coatings on Ti6Al4V, Thermal Spray: Research, Design and Applications, C.C. Berndt and T.F. Bernecki, Ed., ASM International, 1993, p 159–166
S.C. Gill and T.W. Clyne, Stress Distributions and Material Response in Thermal Spraying of Metallic and Ceramic Deposits, Metall. Trans. B, Vol 21 (No. 2), 1990, p 377–385
O.C. Brandt, Measuring of Residual Stresses in Thermal Sprayed Coatings, Thermal Spray Science and Technology, C.C. Berndt and S. Sampath, Ed., ASM International, 1995, p 451–455
M. Finot, S. Suresh, C. Bull, and S. Sampath, Curvature Changes during Thermal Cycling of a Compositionally Graded Ni-A12O3 Multi-Layered Material, Mat. Sci. Eng. A, Vol 205, 1996, p 59–71
P. Scardi, M. Leoni, and L. Bertamini, Influence of Phase Stability on the Residual Stress in Partially Stabilized Zirconia TBC Produced by Plasma Spray, Surf. Coat. Technol., Vol 76 (No. 1–3), 1995, p 106–112
S. Kuroda and T.W. Clyne, The Quenching Stress in Thermally Sprayed Coatings, Thin Solid Films, Vol 200 (No. 1), 1991, p 49–66
O. Kesler, M. Finot, S. Suresh, and S. Sampath, Determination of Processing-Induced Stresses and Properties of Layered and Graded Coatings: Experimental Method and Results for Plasma-Sprayed Ni-Al2O3, Acta Mater., Vol 45 (No. 8), 1997, p 3123–3134
R. Hamacha, B. Dionnet, A. Grimaud, and F. Nardou, Residual Stress Evolution during the Thermal Cycling of Plasma-Sprayed Zirconia Coatings, Surf. Coat. Technol., Vol. 80 (No. 3), 1996, p 295–302
I. Kraus and V.V. Trofimov, X-Ray Stress Measurement, Academia, Prague, 1988 (in Czech)
H.P. Klug and L.E. Alexander, X-Ray Diffraction Procedures for Polycrystalline and Amorphous Materials, John Wiley & Sons, New York, 1974
H. Zantopulos and C.F. Jatczak, Systematic Errors in X-Ray Diffractometer Stress Measurements Due to Specimen Geometry and Beam Divergence, Adva. X-Ray Anal., Vol 14, 1971, p 91–103
S. Fischer, H.R. Maier, and E. Houtman, High Resolution X-Ray Residual Stress Analysis Based on Tetragonal Zirconia, Proc. Eur. Conf. on Residual Stresses, Frankfurt a. M., Germany, 1992, p 361–367
S. Sampath and H. Herman, Rapid Solidification and Microstructure Development during Plasma Spray Deposition, J. Thermal Spray Tech., Vol 5 (No. 4), 1996, p 445–456
S. Leight, “Stereological Investigation of Structure/Property Relationships of Plasma Sprayed Deposits,” Ph.D. thesis, State University of New York, Stony Brook, 1996
R. McPherson, A Review of Microstructure and Properties of Plasma Sprayed Ceramic Coatings, Surf. Coat. Techn., Vol 39–40 (No. 1–3), 1989, p 173–181
J. Ilavsky, A.J. Allen, G.G. Long, H. Herman, and C.C. Berndt, Characterization of the Closed Porosity in Plasma-Sprayed Alumina, J. Mater. Sci., Vol 32 (No. 13), 1997, p 3407–3410
I. Iordanova, K.S. Forcey, B. Gergov, and V. Bojinov, Characterization of Flame-Sprayed and Plasma-Sprayed Pure Metallic and Alloyed Coatings, Surf. Coat. Technol., Vol 72 (No. 1–2), 1995, p 23–29
I. Iordanova, D. Neov, K.S. Forcey, E. Abadjieva, and R. Bezdushnyi, An Analysis of the Influence of Crystallographic Texture on Residual Stress Estimation for Metallic Films and Coatings, Mater. Sci. Forum, Vol 228–231, 1996, p 311–316
R.H. Marion and J.B. Cohen, Anomalies in Measurement of Residual Stress by X-Ray Diffraction, Adv. X-Ray Analysis, Vol 18, 1976, p 466–501
I.C. Noyan and J.B. Cohen, Residual Stress—Measurement by Diffraction and Interpretation, Springer-Verlag, New York, 1987
M. Ceretti, H. Michaud, M. Perrin, and A. Lodini, Residual Stress Measurement in a Plasma Semi-Transferred Arc (PTA) Coating by Neutron and X-ray Diffraction, Exp. Tech., Vol 19 (No. 3), 1995, p 17–21
H. Dolle and J.B. Cohen, Residual Stresses in Ground Steels, Metall. Trans. A, Vol 11A (No. 1), 1980, p 159–164
V.M. Hauk, R.W.M. Oudelhoven, and G.J.H. Vaessen, The State of Residual Stress in the Near Surface Region of Homogeneous and Heterogeneous Materials after Grinding, Metall. Trans. A., Vol 13 (No. 7), 1982, p 1239–1244
I.C. Noyan, Effect of Gradients in Multiaxial Stress States on Residual Stress Measurements with X-Rays, Metall. Trans. A, Vol 14 (No. 2), 1983, p 249–258
P. Gondi, G. Mattogno, R. Montanari, and A. Sili, On the Origin of the Residual Stress psi Splitting, Z. Metallkd., Vol 81 (No. 8,) 1990, p 570–575
H. Furuichi, Unusual Arrangement of the Inclinations of Lattice Planes and psi Splitting, Wear, Vol 113 (No. 3), 1986, p 323–329
M.M. Gola and P. Coppa, Possible Experimental X-Ray Diffractometry Evidence of Couple-Stresses, J. Appl. Mech., Vol 55 (No. 3), 1988, p 539–544
I. Kraus and G. Gosmanová, X-Ray Diffraction Analysis of Macrostresses in Surface Layers of Metallic Materials, Met. Mater., Vol 28 (No. 3), 1990, p 75–79
S. Tobe, H. Misawa, K. Akita, and Y. Kon, Macro- and Microstress in Plasma Sprayed Coatings and Its Stress vs. Strain Behavior, Thermal Spray Industrial Applications, C.C. Berndt and S. Sampath, Ed, ASM International, 1994, p 693–697
S.C. Gill, “Residual Stresses in Plasma Sprayed Deposits,” Ph.D. thesis, University of Cambridge, Cambridge, UK, 1991
J. Dubsky, B. Kolman, P. Ctibor, and F. Kroupa, Structure and Residual Stresses in Thermally Sprayed Steel Coatings, Fifth Int. Symp. on Functionally Graded Materials, Dresden, Germany, 1998
S. Kuroda, T. Fukushima, and S. Kitahara, Significance of the Quenching Stress in the Cohesion and Adhesion of Thermally Sprayed Coatings, Thermal Spray: International Advances in Coatings Technology, C.C. Berndt, Ed., ASM International, 1992, p 903–909
M. Levit, I. Grimberg, and B. Z. Weiss, Residual Stress in Ceramic Plasma-Sprayed Thermal Barrier Coatings: Measurement and Calculation, Mater. Sci. Eng. A, Vol. 206, 1996, p 30–38
P. Scardi, M. Leoni, and L. Bertamini, Residual Stresses in Plasma Sprayed Partially Stabilised Zirconia TBCs: Influence of the Deposition Temperature, Thin Solid Films, Vol 278 (No. 1–2), 1996, p 96–103
S. Sampath, “Rapid Solidification during Plasma Spraying,” Ph.D. thesis, State University of New York, Stony Brook, 1989
J. Matejicek, S. Sampath, and J. Dubsky, Residual Stress Measurement in Plasma Sprayed Coatings by X-Ray Diffraction, Thermal Spray: A United Forum for Scientific and Technological Advances, C.C. Berndt, Ed., ASM International, 1997, p 855–860
Y.C. Tsui and T.W. Clyne, An Analytical Model for Predicting Residual Stresses in Progressively Deposited Coatings, Thin Solid Films, Vol 306 (No. 1), 1997, p 23–61
F. Kroupa, Quenching Residual Stresses in Continuously Thermal Sprayed Coatings and Plates, Acta Tech. CSAV, Vol 42 (No. 5), 1997, p 591–612
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Matejícek, J., Sampath, S. & Dubsky, J. X-ray residual stress measurement in metallic and ceramic plasma sprayed coatings. J Therm Spray Tech 7, 489–496 (1998). https://doi.org/10.1361/105996398770350701
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1361/105996398770350701