Abstract
A major problem with polymeric membranes is low hydrophilicity and consequently a tendency to fouling. Preparing composite membranes is one way to improve the properties and performance of the neat membrane. In the present study, the effects of coagulation-bath temperature (CBT) and the hydrophilic nanoclay concentration of montmorillonite (MMT) on the morphology and performance of asymmetric cellulose acetate butyrate (CAB) membranes were investigated. The membranes were prepared via phase inversion induced by immersion precipitation in a water-coagulation bath. The morphology of the membranes prepared was studied by scanning electron microscopy (SEM). The permeation performance of the membranes prepared was studied by experiments using pure water and bovine serum albumin (BSA) solutions as feeds. The results showed that the membrane thickness and pure water flux (PWF) were increased by adding up to 2 wt.% MMT nanoclay to the casting solution. These two parameters decreased with further addition of MMT, however. In addition, the results obtained in the case of filtration of BSA solution indicated that the addition of MMT in the casting solution increased permeate flux and reduced BSA rejection slightly. Furthermore, increasing the MMT nanoclay concentration in the casting solution increased pure water flux recovery and consequently decreased the fouling. Decreasing the CBT in the presence of MMT during membrane preparation resulted in the formation of a more porous structure and consequently increased the flux and simultaneously decreased the BSA rejection.
Similar content being viewed by others
References
Adoor, S.G., Sairam, M., Manjeshwar, L.S., Raju, K.V.S.N., and Aminabhavi, T.M. (2006) Sodium montmorillonite clay loaded novel mixed matrix membranes of poly(vinyl alcohol) for pervaporation dehydration of aqueous mixtures of isopropanol and 1,4-dioxane. Journal of Membrane Science, 285, 182–195.
Amirilargani, M., Saljoughi, E., Mohammadi, T., and Moghbeli, M.R. (2010) Effects of coagulation bath temperature and Polyvinylpyrrolidone content on flat sheet asymmetric Polyethersulfone membranes. Polymer Engineering & Science, 50, 885–893.
Anadão, P., Sato, L.F., Wiebeck, H., and Diaz, F.R.V. (2010) Montmorillonite as a component of polysulfone nanocom-posite membranes. Applied Clay Science, 48, 127–132.
Anadäo, P., Montesa, R.R., Larocca, N.M., and Pessan, L.A. (2013) Influence of the clay content and the polysulfone molar mass on nanocomposite membrane properties. Applied Surface Science, 275, 110–120.
Fu, X.Y., Sotani, T., and Matsuyama, H. (2008) Effect of membrane preparation method on the outer surface roughness of cellulose acetate butyrate hollow fiber membrane. Desalination, 233, 10–18.
Hajasgarkhani, M.A., Mousavi, S.M., and Saljoughi, E. (2013) Cellulose acetate butyrate membrane containing TiO2 nanoparticle: Preparation, characterization and permeation study. Korean Journal of Chemical Engineering, 30, 1819–1824.
Hashemifard, S.A., Ismail, A.F., and Matsuura, T. (2011) Effects of montmorillonite nano-clay fillers on PEI mixed matrix membrane for CO2 removal. Chemical Engineering Journal, 170, 316–325.
Huang, H.Y., Huang, T.C., Yeh, T.C., Tsai, C.Y., Lai, C.L., Tsaib, M.H., Yeh, J.M., and Chou, Y.C. (2011) Advanced anticorrosive materials prepared from amine-capped aniline trimer-based electroactive polyimide-clay nanocomposite materials with synergistic effects of redox catalytic capability and gas barrier properties. Polymer, 52, 2391–2400.
Liang, C.Y., Uchytil, P., Petrychkovych, R., Lai, Y.C., Friess, K., Sipek, M., Reddya, M.M., and Suen, S.Y. (2012) A comparison on gas separation between PES (polyethersul-fone)/MMT (Na-montmorillonite) and PES/TiO2 mixed matrix membranes. Separation and Purification Technology, 92, 57–63.
Lin, R.Y., Chen, B.S., Chen, G.Y., Wu, J.Y., Chiu, H.C., and Suen, S.Y. (2009) Preparation of porous PMMA/ Na+-montmorillonite cation-exchange membranes for ca-tionic dye adsorption. Journal of Membrane Science, 326, 117–129.
Mansourpanah, Y., Madaeni, S.S., Rahimpour, A., Farhadian, A., and Taheri, A.H. (2009) Formation of appropriate sites on nanofiltration membrane surface for binding TiO2 photo-catalyst: Performance, characterization and fouling-resistant capability. Journal of Membrane Science, 330, 297–306.
Mousavi, S.M., Dehghan, F., Saljoughi, E., and Hosseini, S.A. (2012a) Preparation of modified polyethersulfone membranes using variation in coagulation bath temperature and addition of hydrophilic surfactant. Journal of Polymer Research, 19, 9861–9872.
Mousavi, S.M., Saljoughi, E., Ghasemipour, Z., and Hosseini, S.A. (2012b) Preparation and characterization of modified polysulfone membranes with high hydrophilic property using variation in coagulation bath temperature and addition of surfactant. Polymer Engineering & Science, 52, 2196–2205.
Mousavi, S.M., Saljoughi, E., and Sheikhi-Kouhsar, M.R. (2013) Preparation and characterization of nanoporous polysulfone membranes with high hydrophilic property using variation in CBT and addition of tetronic-1107 surfactant. Journal of Applied Polymer Science, 127, 4177–4185.
Nguyen, Q.T. and Baird, D.G. (2006) Preparation of polymer clay nanocomposites and their properties. Advances in Polymer Technology, 25, 270–285.
Picard, E., Vermogen, A., Gérard, J.F., and Espuche, E. (2007) Barrier properties of nylon 6-montmorillonite nanocomposite membranes prepared by melt blending: Influence of the clay content and dispersion state: Consequences on modeling. Journal of Membrane Science, 292, 133–144.
Rahimpour, A., Madaeni, S.S., Taheri, A.H., and Mansourpanah, Y. (2008) Coupling TiO2 nanoparticles with UV irradiation for modification of polyethersulfone ultrafiltration membranes. Journal of Membrane Science, 313, 158–169.
Ray, S.S and Okamoto, M. (2003) Polymer/layered silicate nanocomposites: A review from preparation to processing. Progress in Polymer Science, 28, 1539–1641.
Sabde, A.D., Trivedi, M.K., Ramachandhran, V., Hanra, M.S., and Misra, B.M. (1997) Casting and characterization of cellulose acetate butyrate-based UF membranes. Desalination, 114, 223–232.
Saljoughi, E., Amirilargani, M., and Mohammadi, T. (2009a) Effect of poly(vinyl pyrrolidone) concentration and coagulation bath temperature on the morphology, permeability, and thermal stability of asymmetric cellulose acetate membranes. Journal of Applied Polymer Science, 111, 2537–2544.
Saljoughi, E., Sadrzadeh, M., and Mohammadi, T. (2009b) Effect of preparation variables on morphology and pure water permeation flux through asymmetric cellulose acetate membranes. Journal of Membrane Science, 326, 627–634.
Saljoughi, E., Amirilargani, M., and Mohammadi, T. (2010) Effect of PEG additive and coagulation bath temperature on the morphology, permeability and thermal/chemical stability of asymmetric CA membranes. Desalination, 262, 72–78.
Saljoughi, E., Mousavi, S.M., and Hosseini, S.A. (2013) Polysulfone/Brij-58 blend nanofiltration membranes: preparation, morphology and performance. Polymers for Advanced Technologies, 24, 383–390.
Samanta, H.S., Ray, S.K., Das, P., and Singha, N.R. (2012) Separation of acid-water mixtures by pervaporation using nanoparticle-filled mixed matrix copolymer membranes. Journal of Chemical Technology and Biotechnology, 87, 608–622.
Shekarian, E., Saljoughi, E., and Naderi, A. (2013) Polyacrylonitrile (PAN)/IGEPAL blend asymmetric membranes: Preparation, morphology and performance. Journal of Polymer Research, 20, 1–9.
Shibutani, T., Kitaura, T., Ohmukai, Y., Maruyama, T., Nakatsuka, S., Watabe, T., and Matsuyama, H. (2011) Membrane fouling properties of hollow fiber membranes prepared from cellulose acetate derivatives. Journal of Membrane Science, 376, 102–109.
Soundararajah, Q.Y., Karunaratne, B.S.B., and Rajapakse, R.M.G. (2010) Mechanical properties of poly(vinyl alcohol) montmorillonite nanocomposites. Journal of Composite Materials, 44, 303–311.
Vora, R.H. and Vora, M. (2006) 1,2-Bis(4-aminophenoxy)-benzene based designed fluoro-poly(ether-imide)/MMT clay nanocomposites: synthesis and properties for high performance applications. Materials Science and Engineering B, 132, 90–102.
Wang, Q., Wang, X., Li, X., Cai, Y., and Wei, Q. (2011) Surface modification of PMMA/O-MMT composite micro-fibers by TiO2 coating. Applied Surface Science, 258, 98–102.
Xing, D., He, G., Hou, Z., Ming, P., and Song, S. (2011) Preparation and characterization of a modified montmor-illonite/sulfonated polyphenylether sulfone/PTFE composite membrane. International Journal of Hydrogen Energy, 36, 2177–2183.
Yang, Y. and Wang, P. (2006) Preparation and characterizations of a new PS/TiO2 hybrid membranes by sol-gel process. Polymer, 47, 2683–2688.
Yang, Y., Wang, P., and Zheng, P. (2006) Preparation and properties of polysulfone/TiO2 composite ultrafiltration membranes. Journal of Polymer Science: Part B: Polymer Physics, 44, 879–887.
Yoon, K., Sung, H., Hwang, Y., Noh, S.K., and Lee, D. (2007) Modification of montmorillonite with oligomeric amine derivatives for polymer nanocomposite preparation. Applied Clay Science, 38, 1–8.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hajasgarkhani, M.A., Mousavi, S.M. & Saljoughi, E. Effects of Coagulation-Bath Temperature And Montmorillonite Nanoclay Content on Asymmetric Cellulose Acetate Butyrate Membranes. Clays Clay Miner. 61, 541–550 (2013). https://doi.org/10.1346/CCMN.2013.0610607
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1346/CCMN.2013.0610607