Abstract
Background
For difficult or rare procedures, simulation offers an opportunity to provide education and training. In developing an adequate model to utilize in simulation, 3D printing has emerged as a useful technology to provide detailed, accessible, and high-fidelity models. Nasal osteotomy is an essential step in many rhinoplasty surgeries, yet it can be challenging to perform and difficult to receive adequate exposure to this nuanced portion of the procedure. As it currently stands, there are limited opportunities to practice nasal osteotomy due to the reliance on cadaveric bones, which are expensive, difficult to obtain, and require appropriate facilities and personnel. While previous designs have been developed, these models leave room for improvement in printing efficiency, cost, and material performance. This manuscript aims to describe the methodology for the design of an updated nasal osteotomy training model derived from anatomic data and optimized for printability, usability, and fidelity. Additionally, an analysis of multiple commercially available 3D printing materials and technologies was conducted to determine which offered superior equivalency to bone.
Methods
This model was updated from a first-generation model previously described to include a more usable base and form, reduce irrelevant structures, and optimize geometry for 3D printing, while maintaining the nasal bones with added stabilizers essential for function and fidelity. For the material comparison, this updated model was printed in five materials: Ultimaker Polylactic Acid, 3D Printlife ALGA, 3DXTECH SimuBone, FibreTuff, and FormLabs Durable V2. Facial plastic surgeons tested the models in a blinded, randomized fashion and completed surveys assessing tactile feedback, audio feedback, material limitation, and overall value.
Results
A model optimizing printability while maintaining quality in the area of interest was developed. In the material comparison, SimuBone emerged as the top choice amongst the evaluating physicians in an experience-based subjective comparison to human bone during a simulated osteotomy procedure using the updated model.
Conclusion
The updated midface model that was user-centered, low-cost, and printable was designed. In material testing, Simubone was rated above other materials to have a more realistic feel.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
The need for practicing procedures outside of the operating room and the role of simulation in filling this gap has been increasingly recognized in today’s paradigm of surgical training. The benefits of surgical simulation are numerous including educational, safety, cost, and outcome-based benefits [1]. Three-dimensional (3D) printing allows for rapid development and production of task trainers to create accessible training opportunities, an ideal complement to the traditional surgical training model.
Rhinoplasty is an extremely common and complex operation requiring both thorough knowledge of anatomy and the technical skills necessary to perform it. It is the most common cosmetic surgery done in the United States with 352,555 having been performed in the year 2020, and more being done for functional purposes, reconstruction after trauma, and revision rhinoplasty [2]. While nasal osteotomy is a cornerstone in this procedure, the step is associated with many potential complications including periorbital edema and ecchymosis, mucosal tears, scar formation, and middle vault collapse causing difficulties breathing [3, 4]. Due to the soft tissue envelope covering the important anatomy and reliance on tactile feedback, this step is difficult to teach and learn.
While previous nasal osteotomy task trainers have been described, in this paper we discuss not only our model, but our approach to designing our task trainer [5]. Literature has shown both high and low fidelity models allow for learning experiences, but high fidelity models may have an increased effect on learning [6]. It is for this reason among others, that the authors tested multiple materials to determine which 3D printing material most closely simulated bone in this anatomic region. Our methods may be applied to the creation of task trainers for other difficult procedural steps. There are multiple 3D printing materials now on the market claiming to simulate bone, but limited literature discussing the fidelity of each material’s performance in specific use cases.
Objective
The objective of this study was to develop an updated, quickly produced, user-centered, low-cost, and bone-like 3D training model for nasal osteotomy.
Design
Image segmentation
In the initial round of designing this model, a CT scan ideal for segmenting, with suitable anatomic features, lack of dental artifact, and thin image slices was identified. The imaging had been done using a LightSpeed Pro(16) CT scanner (GE Medical Systems) at 0.625 mm, and approved by three facial plastic surgeons for the use of this model. After deidentification, the information was imported into processing software (Mimics Innovation Suite, Materialise, Belgium). After isolating the bony anatomy from the scan and cropping to focus on the area of interest, all irrelevant internal anatomy was removed (Fig. 1). Additionally, any cavities that would not be utilized for the osteotomies were filled into a solid form decreasing the total print time. The nasal bones were thinned due to feedback that the prior model felt too thick resulting in difficulty performing the osteotomy and smoothed to create a more natural feel.
Computer aided design
The STL file was brought into SolidWorks (SolidWorks, Dassault Systèmes, Massachusetts, USA) to finish the design process. To reduce the amount of material needed, the eye sockets were cut back (Fig. 2). Additionally, a base was added to increase stabilization during simulation exercises. A 10 mm thick block was extruded on the posterior side to create a flat base for the model. A section of the back was removed to allow for a strap to secure plastic skin over the model. A 5 mm by 6 mm lip was added on the superior and inferior sides to provide more stability on the table and act as holdfast points (Fig. 2). The eye sockets were cut down 7 mm to decrease material waste and improve print efficiency while retaining anatomic structures needed for performing a nasal osteotomy.
A 24 mm diameter semicircle channel was cut midsagittal to improve the post processing dissolution of water soluble PVA support material used and a 1 mm septum was added midsagittal to simulate an anatomic marker and act as a support structure. Bilateral support rods were added to support the nasal bones during osteotomy, replacing the soft tissue that keeps them in place during the real procedure. The final SolidWorks part (Fig. 3) was exported as an STL.
Printing
To print the various models for testing we utilized two different 3D printing modalities: material extrusion (ME) and vat photopolymerization (VP). While our model optimization led to decreased printing time for the PLA model, post-processing time remained around 12 hours for the ME models as PVA material was used as supports and dissolve time remained a rate limiting step. The dissolve time can be expedited by physically removing PVA supports before and during dissolution. ME was used for printing polylactic acid (PLA), FibreTuff, SimuBone, and ALGA. Ultimaker Cura V5.1.1 was used for slicing and an Ultimaker S5 for printing. The nasal osteotomy model made from Durable V2 resin was printed on a FormLabs Form 3B printer with slicing done in PreForm. The same STL file was used to prepare all models and the appropriate material profiles were imported from Ultimaker’s marketplace into Cura when necessary. The infill for ME models was set to 20% to minimize material usage in the base since the nasal bone area would be solid regardless of infill due to its thin wall thickness. Notably, due to the high bed temperature necessary for printing FibreTuff, the Ultimaker PVA supports were not adhering properly to the build plate. The temperature was decreased a few degrees for the first layer and returned to the profile-specified temperature for subsequent layers. All modifications to the profiles as well as cost and material usage are detailed in Additional file 1. The default layer height for each profile was used and was within a 0.1mm difference. For ME models, once the prints finished, the models were removed from the build plate, the adhesion brim was removed, and models were placed in a four-liter container of warm tap water with a stir bar for approximately 12 hours to allow PVA supports to dissolve. For the VP models, parts were removed from the build plate, washed, and cured according to material specifications, and then supports were manually removed.
Material testing
Methods
All five materials were tested at random by board certified facial plastic surgeons and a facial plastic fellow blinded to each other’s preferences. After practicing both percutaneous nasal osteotomy and endonasal osteotomy on a model using standard osteotomes and mallets, each tester filled out a survey specific to their experience with that material. They were blinded to the type and cost of material, in addition to any printing details. Questions about overall value and reality of the models were asked (Additional file 2). Survey responses were exported from Google Forms to Google Sheets (Google, California, USA) and statistics were calculated in Microsoft Excel (Microsoft, Washington, USA).
Results
After some optimization in printing, each material was successfully printed with the parameters outlined in the methods section. Print time ranged from 478 minutes to 730 minutes and cost ranged from $4.54 - $50.37 depending on the material (Table 1).
Two attending facial plastic surgeons and one fellow facial plastic surgeon tested the materials and filled out the survey. Performance of the materials in tactile feedback, audio feedback, and material limitation varied greatly between each material and at times depending on the technique used (Table 2). SimuBone’s ratings were best across all categories for both techniques. All the other materials performed well in some categories and not well in others (Tables 2 and 3). While the Durable V2 resin material scored very well when utilized for the endonasal technique, it did not perform nearly as well during the percutaneous portion of testing (Table 2).
SimuBone was chosen as the first material of preference by all 3 surgeons (Table 4). For second preference, there was more variability in responses with Alga, Durable V2 resin, and PLA each earning second preference by one of the surgeons. FibreTuff was the least preferred with two surgeons choosing it as their last choice and one putting it in fourth place.
Discussion
The objective of this study was to create a low cost, high fidelity, and time-efficient for production nasal osteotomy model while testing for the superior, 3D printable, bone-like substitute for cadaveric bone in this procedure. Rhinoplasty is an extremely common procedure and therefore all trainees should ideally graduate residency feeling competent in all of the steps. Yet technical training remains a known challenge with 28% of senior residents and 87% of junior residents feeling insufficiently exposed to rhinoplasty during residency with nasal osteotomy to be the technique they were least confident in performing [7]. This has led to a call for focused, maneuver-specific simulation. Preliminary data from this model has been shown to increase confidence, but further studies must be done [8].
In this study, we used an Ultimaker S5 3D printer with dual extrusion capability and a FormLabs Form 3B, relatively affordable and accessible printers. We chose to utilize the software that the authors were most comfortable with; however there are many free software programs that accomplish similar functions. This model was made for the purpose of simulation and therefore is not personalized nor a surgical guide [9]. All of the materials chosen were commercially available and sourced online. No financial support was obtained from the manufacturers for the purchase of these materials, and they were each purchased via standard publicly available purchasing pathways.
We focused on making our model efficient for 3D printing, resulting in a 52.7% reduction in time printing the new model in PLA compared to the previously published model printed in PLA [6]. Although the updated model took less time to print in PLA, the necessary anatomical structures for the osteotomy procedure were kept intact. Additionally, a channel was added to the design when it was observed that it was difficult to remove all the PVA from the area of interest. Although this increased print time in this material, the channel allowed for water to circulate through the model thus making clearing the PVA away from the region of interest easier.
While many materials are listed as mimicking bone, there is a paucity of literature comparing them or describing their ideal use. This study compares the details of their printing and the performance of the materials when used to print training models for nasal osteotomy. We believe this kind of comparison can be useful for others determining the best material for any medical education simulation project involving bone.
This model was designed to be a simpler version of the previously published design; however, it was still printed with a dual extrusion printer using PVA for soluble support. This limits the number of end users that are able to print the model as most commercially available ME 3D printers use a single extruder. Additionally, a major limitation in the material analysis was the small sample size of three experienced surgeons to conduct testing. Proper evaluation of the tactile and auditory feedback of this device requires surgeons to have performed numerous nasal osteotomies on actual patients which limits the number of people qualified to evaluate the models.
A single preliminary test of printing the unaltered model using PLA material without any PVA support on an Ultimaker S5 printer demonstrated that the model is able to be printed with minimal deformity that should not affect functionality. We elected to utilize supports for optimal quality in this material comparison study and further testing is necessary to evaluate the functional quality of the model printed without support. In the future, we hope to do a full resident training conference day with the SimuBone material to explore the impact that may have on the educational experience.
Conclusion
In this study, we demonstrate the optimization of a previously published nasal osteotomy task trainer using techniques that optimized the design for 3D printing. By creating a model prioritizing printing efficiency and total cost, this new task trainer is more accessible for utilization in simulation of nasal osteotomy in rhinoplasty surgery. Moreover, SimuBone proved to be a more realistic material for simulating the anatomic region of the nasal bone according to our measurement scheme while maintaining accessibility at a relatively low-cost when compared to cadaveric bone. For those with access to a 3D printer and readily accessible supplies, this work allows for high-fidelity and low-cost accessible surgical trainee education.
Availability of data and materials
Data is available by reasonable request to the corresponding author.
Change history
21 August 2023
A Correction to this paper has been published: https://doi.org/10.1186/s41205-023-00188-6
Abbreviations
- 3D:
-
Three-dimensional
- ME:
-
Material Extrusion
- VP:
-
Vat Photopolymerization
- PLA:
-
Polylactic acid
References
Dunkin B, Adrales GL, Apelgren K, Mellinger JD. Surgical simulation: a current review. Surg Endosc. 2007;21(3):357–66.
Plastic Surgery Statistics | American Society of Plastic Surgeons [Internet]. Available from: https://www.plasticsurgery.org/news/plastic-surgery-statistics. [cited 2023 Feb 2].
Zaher MM, Elfeki B, Ismail KA, Ismail TA, Hegazy SA. Early postoperative sequelae after open sky access in nasal osteotomy: A comparative study. Ann Plast Surg. 2022;88(5):480–4.
Camirand A, Doucet J, Harris J. Nose surgery: how to prevent a middle vault collapse–a review of 50 patients 3 to 21 years after surgery. Plast Reconstr Surg. 2004;114(2):527–34.
Ho M, Goldfarb J, Moayer R, Nwagu U, Ganti R, Krein H, et al. Design and Printing of a Low-Cost 3D-Printed Nasal Osteotomy Training Model: Development and Feasibility Study. JMIR Med Educ. 2020;6(2): e19792.
Kim J, Park J-H, Shin S. Effectiveness of simulation-based nursing education depending on fidelity: a meta-analysis. BMC Med Educ. 2016;16:152.
Zammit D, Ponnudurai N, Safran T, Gilardino M. Reevaluating the Current Model of Rhinoplasty Training and Future Directions: A Role for Focused Maneuver-Specific Simulation. Plast Reconstr Surg. 2019;144(4):597e–605e.
Schlegel L, Kumar A, Christopher V, Belko S, Barbarite E, Pugliese R, Krein H, Mutchinson M, Heffelfinger R. Tap-Tap: Learning Endonasal and Percutaneous Nasal Osteotomy Techniques on 3D-Printed Midface Models. Otolaryngol Head Neck Surg. 2023.
Mitsouras D, Liacouras PC, Wake N, Rybicki FJ. RadioGraphics Update: Medical 3D Printing for the Radiologist. Radiographics. 2020;40(4):E21–3.
Acknowledgments
The authors would like to thank MaryEllen Daley and the Health Design Lab for helping to print and process models for this study. Publication made possible in part by support from the Jefferson Open Access Fund.
Funding
The authors received no funding for this manuscript.
Author information
Authors and Affiliations
Contributions
LS, SB, RP, and AK designed the nasal osteotomy model. EM and LS printed the models in different materials. RH, HK, and EB tested the materials. LS and EM conducted formal analysis of the data. LS, EM, and SB wrote the original draft. All authors reviewed and edited the final manuscript.
Corresponding author
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
The original online version of this article was revised: The text “Flex 80A” has been corrected to “Durable V2” in Tables 2, 3 and 4.
Supplementary Information
Additional file 1:
Printing profiles for each material.
Additional file 2:
Material testing questionnaire for nasal osteotomy simulation.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.
About this article
Cite this article
Schlegel, L., Malani, E., Belko, S. et al. Design, printing optimization, and material testing of a 3D-printed nasal osteotomy task trainer. 3D Print Med 9, 20 (2023). https://doi.org/10.1186/s41205-023-00185-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s41205-023-00185-9