Abstract
Background
The primary function of a suspension system is to isolate the vehicle body from road irregularities thus providing the ride comfort and to support the vehicle and provide stability. The suspension system has to perform conflicting requirements; hence, a passive suspension system is replaced by the active suspension system which can supply force to the system. Active suspension supplies energy to respond dynamically and achieve relative motion between body and wheel and thus improves the performance of suspension system.
Methods
This study presents modelling and control optimization of a nonlinear quarter car suspension system. A mathematical model of nonlinear quarter car is developed and simulated for control and optimization in Matlab/Simulink® environment. Class C road is selected as input road condition with the vehicle traveling at 80 kmph. Active control of the suspension system is achieved using FLC and PID control actions. Instead of guessing and or trial and error method, genetic algorithm (GA)based optimization algorithm is implemented to tune PID parameters and FLC membership functions’ range and scaling factors. The optimization function is modeled as a multiobjective problem comprising of frequency weighted RMS seat acceleration, Vibration dose value (VDV), RMS suspension space, and RMS tyre deflection. ISO 26311 standard is adopted to assess the ride and health criterion.
Results
The nonlinear quarter model along with the controller is modeled and simulated and optimized in a Matlab/Simulink environment. It is observed that GAoptimized FLC gives better control as compared to PID and passive suspension system. Further simulations are validated on suspension system with seat and human model. Parameters under observation are frequencyweighted RMS head acceleration, VDV at the head, crest factor, and amplitude ratios at the head and upper torso (AR_h and AR_ut). Simulation results are presented in time and frequency domain.
Conclusion
Simulation results show that GAbased FLC and PID controller gives better ride comfort and health criterion by reducing RMS head acceleration, VDV at the head, CF, and AR_h and AR_ut over passive suspension system.
Similar content being viewed by others
Background
The main function of an automotive suspension system is to support the vehicle weight, to isolate the occupants against the excitations caused by road unevenness and thus providing the ride comfort and better handling, and to keep the contact between tyre and ground. The task of the suspension system is a tradeoff between ride and performance as ride comfort needs soft suspension system whereas to follow track and support vehicle weight stiff suspension system is required.
The primary objective of the active suspension system is to replace the passive suspension system by a controlled system which can supply force to the system. Active suspension supplies energy to respond dynamically and achieve relative motion between the body and the wheel. Thus, to changing road conditions, active suspension system improves the performance of the suspension system such as ride comfort, suspension or rattle space displacement, tyre displacement, and body displacements (Wong 2001). For active control, various control strategies are implemented like optimal control, robust control, nonlinear control, nonlinear control with backstepping, sliding mode control, intelligent control, neural control, and hybrid control. One of the main objectives was to minimize body acceleration to improve ride comfort.
Metered et al. (2015) had implemented particle swarm optimization (PSO) algorithm to tune the PID controller implemented on a semiactive quarter car suspension system. A 2DoF model with MR damper is simulated in a Matlab/Simulink environment with bump and random road inputs. The system was tested in time and frequency domain. It was observed that POS tuned PID controller improves ride comfort and vehicle stability. Kesarkar and Selvaganesan (2015) designed fractional order PID controller using artificial bee colony algorithm with objective functions such as integral absolute error, integral square error, and integral time absolute error implemented to a multimodal complex optimization problem. The authors observed that the results were promising as compared to the conventional PID method. Niu (2014) had implemented GAbased optimization method to tune PID parameters of the active suspension system. Absolute error control is used as an objective function to tune the PID parameters. It was observed that the GAbased optimized PID controller improves the dynamic performance of the active suspension system and improves stability. Gad et al. (2017) implemented a fractional order PID controller to a semiactive seat suspension. PID parameters are tuned using multiobjective GA for a seat suspension system using the 6DoF human body. It is observed that GAbased PID controller improved SEAT value, VDV ratio, and crest factor as compared to the passive system and classical PID controller. Results are obtained in time as well as frequency domain. Tammam et al. (2013) implemented a multiobjective GAbased PID controller to control the load frequency of a single area power system. It is observed that GAbased PID controller is simple and easy to implement and improves system performance effectively. Abdelrassoul et al. (2016) studied the performance of the PV system based on GAoptimized PID controller. Here, PID controller is implemented to enhance PV system output with minimum overshoot and minimum rise time in output voltage with the better response. Chen and Chang (2006) studied GAbased PID tuning for active magnetic bearing. The proposed PID controller shows that the active magnetic bearing had good static and dynamic performance and showed better performance and effectiveness.
It is observed that optimization of PID controller applied to suspension system is carried out in single objective nature (Metered et al. 2015; Niu 2014) whereas (Kesarkar and Selvaganesan 2015) presented a multimodal optimization approach and (Gad et al. 2017) presented dual objective function optimization.
Kalaivani et al. (2014) studied a fuzzy logicbased active quarter car suspension system. A hybrid differential evolution biogeography based optimization algorithm is used to tune the FLC controller. RMS body acceleration is used as performance index to study the PID and newly proposed FLC controller. It was observed that the proposed controller improves the ride comfort. Taskin et al. (2017) implemented the FLC controller on a quarter car test rig. Time and frequency domain response of sprung mass displacement, acceleration, and suspension space deflection and actuator force are studied and compared with passive suspension system and observed that FLC controller performance better. Huang and Chao (2000) implemented a fuzzy logic controllerbased active suspension system on a quarter car model. Results showed that the control strategy improves ride comfort reducing the oscillations of the body. Salem and Aly (2009) had studied the 2DoF quarter suspension system. FLC is used to control the quarter car active suspension system. Body acceleration is used as a criterion to study the ride comfort of a suspension system, along with handling. FLC and PID controller are studied and observed that FLC performs better compared to the PID controller. Rajendiran and Lakshmi (2016) analyzed active control of 2DoF suspension system using PID control and FLC along with seat and driver model. It was observed that FLC improves ride comfort than that of PID control and passive system. Taskin et al. (2007) studied the FLC controller to enhance ride comfort. From time response of the active system, it is observed that body displacement is minimized without losing suspension working space. Results were obtained in the frequency domain which shows improved ride comfort. From above discussions, it is observed that researchers (Taskin et al. 2017; Huang and Chao 2000; Salem and Aly 2009; Rajendiran and Lakshmi 2016) have successfully implemented the FLC for ride control applications, whereas (Kalaivani et al. 2014) optimized FLC using a single optimization function.
Talib and Darus (2014) implemented a semiactive suspension system using FLC and PID controllers. Performance of both the controllers is optimized by the PSO algorithm for mean square error. Optimized FLC, PID controllers are compared with a passive suspension system for body displacement, acceleration, tyre displacement for bump, and hole disturbances. It is observed that the FLC controller gave better results as compared to the PID controller. Celin and Rajeswari (2012) implemented type2 FLC to the active suspension system. Sprung mass displacement, RMS acceleration, suspension space, and tyre deflection criterions were used to study the FLC and passive suspension system. GAcoded FLC outperforms the FLC and passive suspension system. D’Amato and Viassolo (2000) presented the active suspension system to reduce the body acceleration to improve comfort. FLC is used to control where parameters are tuned by GA optimization. This methodology improves ride comfort thus was effective in case of a quarter car suspension system. Li and Du (2006) presented a GAbased approach to optimize rule base and scaling factors. The parameters were coded into realcoded strings and treated as chromosomes during optimization. The GAbased optimization approach improves the performance of FLC. Liu et al. (2016) had successfully optimized the membership functions of FLC to a maximum power point tracking (MPPT) algorithm using PSO algorithm to improve averaged tracking error and fitness value. Bouarroudj et al. (2017) had presented the comparative analysis of Mamdani FLC with Gaussian membership functions for MPPT of PV system using GA and PSO approach. It was observed that PSO and GA optimized FLC gives better results in terms of performance.
This paper presents the mathematical modelling of a nonlinear quarter car (NLQC) along with a human model. The nonlinear quarter car model consists of quadratic tyre stiffness and cubic stiffness in suspension spring as nonlinearities. PID and FLC are implemented with the control objective to minimize frequency weighted RMS sprung mass acceleration (hereafter called as RMS sprung mass acceleration), VDV, RMS suspension space requirement, and RMS tyre deflection along with RMS optimal control force. The constraints on optimization are maximum control force, maximum sprung mass acceleration, maximum suspension space requirement, and maximum tyre deflection. Due to multiobjective natures of optimal control and conflicting control objectives, the key issue is to select the PID gain values and range of fuzzy input and output membership functions and scaling factors to fulfill the conflicting requirements. Trial and error method and or manual tuning of the PID controller and FLC are cumbersome and timeconsuming. Hence, a GAbased evolutionary optimization technique is used to search the optimum parameters. During optimization, a nonlinear optimal control system is simulated in a Matlab/Simulink® environment where the tuning parameters are selected from the search space. The output of the nonlinear optimal control system is fed to the optimization algorithm to determine the objectives and validate the constraints. The optimization procedure is repeated up to 100 generations. Further, the optimization results are validated on a quarter car with seat and human model. Results are presented in both time domain and frequency domain.
Methods
Mathematical modelling—nonlinear quarter car suspensionseathuman model
A suspension system consists of damper and coil springs. Researchers have used various mathematical models viz. quarter car model having 2DoF, a half car model having 4DoF, and full car model. In this study, a 2DoF quartercar model is implemented for ride and control applications (Metered et al. 2015; Kalaivani et al. 2014; Taskin et al. 2017; Huang and Chao (2000); Salem and Aly 2009; Rajendiran and Lakshmi 2016).
Mathematical modeling is carried out using linear springs and damper by various authors (Kalaivani et al. 2014; Taskin et al. 2017; Huang and Chao (2000); Salem and Aly 2009; Rajendiran and Lakshmi 2016). But it is observed that spring exhibits nonlinear nature so do the tyre (Fuller et al. 1996). Thus, the nonlinearity should be considered during modeling. McGee et al. (2005) studied nonlinearities in the suspension system using a frequency domain technique and are validated experimentally with shaker data. It was observed quadratic and cubic stiffness and Coulomb friction nonlinearities in the suspension system (McGee et al. 2005). A chaotic response was presented by Zhu and Ishitobi (2006). They used a 7DoF model with tyre stiffness and suspension spring stiffness nonlinearities. Bifurcation and chaotic response of 2DoF model with tyre stiffness and suspension spring stiffness nonlinearities were presented by Lixia and Wanxiang (2008).
In the present analysis, a nonlinear quarter car model having quadratic tyre stiffness and cubic stiffness in suspension spring nonlinearities are considered.
A human model suggested by (Boileau and Rakheja 1998) is incorporated further in this study. The model is having 4DoFs consisting of head and neck mass (m_{h}), chest and upper torso mass (m_{ut}), lower torso mass (m_{lt}), and thigh and pelvis mass (m_{t}). The human model considers typical driving conditions such as seated posture with feet support and hands held in driving conditions (refer to Fig. 1).
According to D’Alembert’s principle, the governing equations of motion representing nonlinear quarter car suspensionseathuman model are represented as –
The nonlinear quarter car seatsuspensionhuman model parameters are as follows:

m_{h} = 5.31; c_{h} = 400; k_{h} = 310,000;

m_{ut} = 28.49; c_{ut} = 4750; k_{h} = 183,000;

m_{lt} = 8.62; c_{lt} = 4585; k_{lt} = 162,800;

m_{t} = 12.78; c_{t} = 2064; k_{t} = 90,000;

m_{c} = 1; c_{c} = 200; k_{c} = 18,000;

m_{f} = 15; c_{f} = 830; k_{f} = 31,000;

m_{s} = 290; c_{s} = 700; k_{s} = 23,500; k_{snl} = 100k_{s} (Lixia and Wanxiang 2008);

m_{us} = 40; k_{t} = 190,000; k_{tnl} = 1.5 k_{t} (Zhu and Ishitobi 2006).
The nonlinear quarter car having quadratic stiffness nonlinearity in the tyre and cubic stiffness in suspension spring is modeled and simulated in Matlab/Simulink®. Further, the simulations are carried out on a quarter car model with seat consisting frame and cushion with a human model.
Control theory—PID control
PID stands for proportional, integral, and derivative and is a classical controller used for several control applications (Metered et al. 2015; Kesarkar and Selvaganesan 2015; Niu 2014; Gad et al. 2017; Tammam et al. 2013; Abdelrassoul et al. 2016; Chen and Chang 2006). The PID controllers are so designed that continuous attention of the operator is eliminated. As the PID controller has designed a derivative nature type, small variation of output can be easily avoided. A PID controller is depicted in Fig. 2. The set point is where the measurement should be. An error is defined as the difference between the set point r(t) and measurement y(t). PID computes the control signal based on the following equations:
The error, e(t), variable being adjusted is called the manipulated variable which usually is equal to the output of the controller. As there is a change in measurement or set point, so is the output of the controller. Generally, ZN tuning or autotuning is used to tune the P, I and D parameters of the controller.
Control theory—fuzzy logic control
FLC uses heuristic information for control applications. The FLC uses rulebase derived through an operator’s experience and thus acts as a humanintheloop controller providing human experience to achieve high performance (Kalaivani et al. 2014; Taskin et al. 2017; Huang and Chao 2000).
Figure 3 represents the structure of a typical FLC implemented for a 2DOF suspension system. Here, two inputs (error e and ec) and one output (force f_{FLC}) FLC with rulebase is implemented. Sprung mass velocity (error e) and acceleration (change in error ec) are used as input, and control force (f_{FLC}) is output. FLC rule base is a linguisticbased rule base which incorporates past human experience. Table 1 represents the rule base for two inputone output rule base for ride comfort. Figure 4 represents the surface plot rule base as stated in Table 1.
Firstly, FLC decomposes the input into fuzzy sets, called as fuzzification, using membership functions (MF). Primarily membership functions map practical space to fuzzy space, known as fuzzification. Here, trapezoidal membership functions are used for input and output variables (refer Figs. 5, 6, and 7). The FLC consists of seven membership functions each, ie., for two inputs (error e and change in error ec) and an output f_{FLC}; these are NL, NM, NS, ZE, PS, PM, PL. Mamdani type fuzzy inference system (FIS) is used. Defuzzification is the process which maps the variables back to practical space from fuzzy space. Centroid defuzzification method is used in this FLC.
Objective functions
One of the key factors in optimization problems is to choose proper objective functions. Here, the control strategies are implemented to improve ride characterized by RMS sprung mass acceleration, VDV, RMS suspension space deflection, RMS tyre deflection, and RMS controller force.
RMS acceleration
As per ISO 26311 (1997), RMS acceleration is given by
A major portion of the vibration experienced by the occupants of an automobile enters the body through the seat (Van Niekerk et al. 2003; Bovenzi 2005). The health risk increases as the exposure time to vibrations increases. Hence, is it necessary to measure the whole body vibrations for ride and health criterion. As per ISO 26311 (1997), VDV is one measure for whole body vibrations. VDV also called as fourth power vibration dose. VDV is the method of assessing the cumulative effect (dose) of the vibration.
Vibration dose value (VDV)
VDV is the fourth power of acceleration time histories. It is expressed as 
Suspension travel
Suspension travel is characterized by the relative travel between the sprung mass and unsprung mass. Due to random input, RMS suspension space travel is taken as one of the objective functions.
Dynamic tyre deflection
Dynamic tyre force is related to tyre deflection. Due to the random nature of input, the RMS of tyre deflection is the next objective function.
Control force is introduced as one of the objective functions, to find optimum control force to achieve ride comfort.
According to Baumal et al. (1998), at least, 125 mm of suspension travel is required, and maximum seat acceleration should not increase 4.5 m/s^{2} to avoid hitting the suspension stop. To minimize dynamic tyre forces, maximum tyre deflection should not increase 0.0508 m. These parameters are included as constraints in the optimization problem.
The formulation of the optimization problem is as follows:
Subject to constraints:
Multiobjective optimization
Researchers have invented several metaheuristic optimization algorithms to optimize the problems in several fields. These algorithms have implemented on several mathematical problems involving single objective optimization to multiobjective optimization and provided excellent results.
The suspension system has to perform several conflicting objectives such as ride comfort, road holding, and suspension/rattle space requirements. Thus, the optimization problem becomes a multiobjective type (consisting of RMS control force, VDV, RMS sprung mass acceleration, RMS suspension space requirement, and RMS dynamic tyre deflection as objective functions) with conflicts. As compared to a single objective optimization problem, a multiobjective optimization (MOO) problem has to satisfy several objectives simultaneously. Hence, multiobjective optimization using a genetic algorithm (GA) (Holland 1992; Holland 1975) is implemented to solve the optimization problem.
In the solution of MOO problems, MOO forms a Pareto optimal front consisting of multiple optimal solutions. GA is implemented to optimize in multiple domains as it handles complex optimization problems with discontinuities, nondifferentials, noisy functions, and functions with multimodality. GA also supports parallel computations with obtaining Pareto front in a single run. Nondominated sort GAII (NSGAII) (Deb et al. 2002) is one of the MOEAs using GA strategy. NSGAII implements nondominated sort algorithm thus reducing the computational complexities. While sorting the parents and children, elitism is introduced in NSGAII. In NSGAII, to preserve the diversity and uniform spread of optimal front, a crowding distance (CD) (Deb et al. 2002) operator is used. Chromosomes with better fitness are assigned highest ranks, and thus, they determine the domination.
From the nondominated front, parents are selected by tournament selection and compared to the CD. New offsprings are created using a crossover operator and mutation operator. New offsprings and current population (parents) are combined to generate a new population. Selection is carried out for next generation individuals. The binary tournament selection method is used by NSGAII to handle constraints. For multiobjective optimization, NGPM code (NSGAII Program in Matlab) is used (Song 2011; Song 2015). NGPM is the implementation of NSGAII (nondominated sort genetic algorithm) in Matlab.
Optimization methodology—PID control
During simulation and optimization of PID controller, PID parameters are randomly initialized, and objective functions are determined. Then, optimum PID parameters are iteratively obtained till algorithm stops. The classical PID gains are determined using the ZN method.
Search space for PID controller is as follows 
Optimization methodology—fuzzy logic control
FLC is a typical two inputone output functions controller. In this design, initially, seven trapezoidal membership functions are defined for two inputs and output. The seven membership functions are initialized in the range of [− 1 1] and are then multiplied using respective scale factors. Table 2 represents the initial membership functions in the range of [− 1 1]. Also, error (e), change in error (ec) and control output (f) are scaled using scaling factors ke, kec, and kf respectively and included in the Simulink® model.
During optimization, values are randomly initialized and the model is simulated to determine objective functions. Then, iteratively optimum parameters are obtained from their ranges till the algorithm stops.
The search space for the inputoutput functions and scaling factors is as follows:
NSGAII—population range
In GA, the range of design variable Kp is (15000–2000=) 13,000. Thus, the design variable Kp needs to be divided into 13,000 equal range of size. Hence, 2^{13} = 8192 < 13,000 < 2^{14} = 16,384, i.e., 14 bits are required to store the value of design variable Kp in the chromosome. Similarly, for other design variables, the bit required is tabulated in Table 3.
Hence, the total length of chromosome or gene is 14 + 08 + 16 = 38 bits that are required, where the first 14 bits are required for Kp, the next 08 bits are required for Ki, and the next 16 bits are required for Kd. Population size is selected such that
N_{s} < population size < 2N_{s}, where N_{s} = string length (Alander 1992)
Also, the range of variables for the FLC design variables is small as compare to the PID controller. Thus, selecting population size of 100 (Rosenthal and Borschbach 2014; HernándezDíaz et al. 2008; Nagarkar et al. 2016) and optimization is stopped after 100 generations. Figure 8 explains the flowchart of the GA algorithm implemented for multiobjective optimization.
Results and discussion
Multiobjective optimization of the nonlinear quartercar model is simulated in a Matlab/Simulink® environment using NSGAII algorithm.
The stationary road roughness is effectively described by power spectral density (PSD). When a car moves at a constant velocity v, the road roughness can be viewed as a stationary process in the space domain. The differential equation of road roughness can be expressed as (He et al. 2008; Zhang et al. 2007):
Equation (11) is modeled in the Simulink environment to model the road surface. According to ISO 8608, roads are divided into classes like A, B, C, D, and E. Class A and B represents expressways or motorways, whereas class C road is a typical average road type. Class B and C roads are generally country or district roads. Class C road considers velocities of typical secondary roads ranging from ~ 30 kmph to ~ 60 kmph. The input road condition is modeled as class C road (average road) with a degree of road roughness 512 × 10^{−6} m^{2}/(cycle/m) (Zhang et al. 2007; ISO 8608 1995). Refer to Table 4 for the road roughness classification. The vehicle is traveling with a velocity of 80 kmph. Figure 9 represents the class C road surface.
PID controller
The tradeoff front of 100 different solutions for objective functions satisfying the constraints is obtained after optimization. The tradeoff front is shown in Fig. 10. For ride comfort and health criterion, RMS acceleration and VDV are selected as optimum values. Hence, for PID controller P, D and D parameters’ gain values are selected for minimum valued of RMS acceleration and VDV and simulated further. Refer to Table 7 for the corresponding optimized PID parameters.
It is observed that the RMS acceleration for the GAoptimized PID controller is 0.6178 m/s^{2}, which is a little uncomfortable. In GAPID controlled system, RMS acceleration is reduced by 34% (passive suspension system has RMS acceleration 0.9322 m/s^{2} which is uncomfortable) and is reduced by 10% as compared to the classical PID control. For GA optimized PID controller, VDV is reduced by 33% as compared to the passive suspension system and is reduced by 11% as compared to classical PID control. Also, constraints are not violated in the GA optimized system. The results of RMS optimal control force, RMS sprung mass acceleration, RMS suspension space, RMS tyre deflection, maximum controller force, and maximum sprung mass acceleration are tabulated in Table 5 (refer to Fig. 11 for time domain results).
Further frequency domain analysis is carried out for the PID controlled system and passive system. In frequency analysis, it is observed that the optimized PID controlled system experiences low amplitudes of body accelerations as compared to the passive suspension system (refer to Fig. 12). PID can reduce the amplitude of body accelerations at points 10^{0} and 10^{1} Hz frequencies. Also, it shows better performance over higher amplitude regions > 10 Hz.
Fuzzy logic control
During simulation 2DOF nonlinear active suspension system, it is excited by a random road disturbance. The NSGAIIbased optimization is carried out and results are obtained using a MATLAB/SIMULINK. The velocity and acceleration of sprung mass are selected as an error (e) and change in error (ec) feedback signals for the 2DOF suspension system control.
The tradeoff front of 100 different solutions for objective functions satisfying the constraints is obtained after optimization. The tradeoff front is shown in Fig. 13. For ride comfort and health criterion, the minimum RMS acceleration and VDV are selected as optimum values. Hence, FLC parameters, ke, kc, kf, and scaling factors for inputoutput membership functions are selected having minimum values of RMS acceleration and VDV corresponding to the tradeoff front and are simulated further. Refer to Table 7 for the corresponding optimized FLC parameters.
It is observed that RMS acceleration for the GAoptimized FLC is 0.5057 m/s^{2}, which is a little uncomfortable. In the fuzzy logic control system, RMS acceleration is reduced by 46% as compared to the passive system (passive suspension system has RMS acceleration 0.9322 m/s^{2} which is uncomfortable) and by 18% as compared to GAbased PID controller. Also, VDV for GAbased FLC is reduced by 45% as compared to the passive suspension system and by 18% as compared to the GAbased PID controller. Also, the RMS suspension space and RMS tyre deflection are less for FLC as compared to the GAbased PID controller and passive suspension system. The constraints are not violated in GA optimized FLC. The results of RMS optimal control force, RMS sprung mass acceleration, RMS suspension space, RMS dynamic tyre deflection, and maximum controller force are maximum sprung mass acceleration are tabulated in Table 5 (refer to Fig. 14 for the time domain results). Results are also shown in the bar chart (refer to Fig. 15).
From simulations and Table 5, it is observed that the GAtuned FLC controller performs better as compared to the GAtuned PID controller. In the case of GAtuned FLC controller, VDV and RMS acceleration is reduced by 18.23% and 18.14% as compared to the GAtuned PID controller. Also, RMS suspension space deflection and RMS tyre deflection is less for the GAtuned FLC controller.
Further, the frequency domain analysis is also carried out for the FLC system and passive system. For frequency analysis, it is observed that the FLC system experiences low amplitudes of vibrations over a broader range of frequencies as compared to the passive suspension system (refer to Fig. 16). The FLC can reduce the amplitude of body accelerations at points 10^{0} and 10^{1} Hz frequencies and also shows better performance over higher amplitude regions > 10 Hz.
Further, to study the controller performance, the nonlinear quarter car suspension system is simulated over class C and class D roads with vehicle speed ranging from 20 to 160 kmph. Figure 17 shows performance over class C road type. For class C road, the maximum value of VDV is 1.8385 m/s^{1.75} and is observed at 160 kmph, for GAtuned PID controller. Whereas for the GAbased FLC maximum VDV is 1.7205 m/s^{1.75}. The maximum value of RMS sprung mass acceleration is 0.7910 m/s^{2} for the GAtuned PID controller and 0.7065 m/s^{2} for the GAFLC controller and is observed at 160 kmph. From Fig. 17, it is observed that, for FLC controller, up to 130 kmph speed, the RMS sprung mass acceleration is in a slightly uncomfortable region as per ISO26311:1997. Whereas for the PID controller, the same level is achieved up to 100 kmph. Above these speed limits, the RMS sprung mass acceleration falls under the fairly uncomfortable region. Other parameters like RMS suspension space and RMS tyre deflection are also represented in Fig. 17.
The nonlinear quarter car is also simulated over class D road. Figure 18 shows the performance of the nonlinear quarter car with both controllers over class D road. From the figure, it is observed that FLC and PID controller shows nearly the same performance for the RMS sprung mass acceleration. The VDV value is maximum at 160 kmph for both controllers. The maximum VDV for PID controller is 2.1874 m/s^{1.75} and for FLC controller VDV is on the slightly higher side and is 2.6091 m/s^{1.7}. The maximum RMS sprung mass is the acceleration is observed at 160 kmph for both controllers and is 0.9391 m/s^{2} for the GAtuned PID controller and 0.9586 m/s^{2} for GAFLC controller respectively. From Fig. 18, it is observed that for FLC controller, up to 80 kmph speed, the RMS sprung mass acceleration is in a slightly uncomfortable region whereas for PID controller, the same level is achieved up to 70 kmph as per ISO26311:1997. Above these speed limits, RMS sprung mass acceleration falls under the fairly uncomfortable region.
To check the effect of vibrations on a human body, the suspension system along with the human model is simulated. The nonlinear quarter car along with seat and human model is simulated using PID and FLC system and compared with a passive system. VDV at the head, RMS head acceleration, crest factor, and amplitude ratios are observed.
Crest factor (CF) is defined as the ratio of maximum head acceleration to the RMS head acceleration [26].
The amplitude ratio of head RMS acceleration to seat RMS acceleration (AR_h) is defined as the ratio of the RMS head acceleration to the RMS seat acceleration (Nagarkar et al. 2016).
The amplitude ratio of upper torso RMS acceleration to seat RMS acceleration (AR_ut) is defined as the ratio of the RMS upper torso acceleration to the RMS seat acceleration (Nagarkar et al. 2016).
It is observed that the RMS head acceleration is reduced by 39% in the case of the GAbased FLC and reduced by 46% in the case of the GAbased PID controller as compared to the passive suspension system, whereas VDV at the head is reduced by 39% and 41% for FLC and PID controller as compared to the passive system. CF, AR_h, and AR_ut parameters are reduced for FLC as compared to the PID and passive suspension system. Results are tabulated in Table 6 and are presented in the bar chart (refer to Fig. 19).
From Table 6 and Fig. 19, it is observed that the GAtuned FLC has RMS acceleration of head and VDV at head slightly greater (1.9% and 1% respectively) as compared to the GAtuned PID controller. But, FLC gives better results as compared to the PID controller for CF, AR_h, and, AR_ut (20.75%, 4.98%, and 9.07% less respectively as compared to PID controller).
From frequency domain results, it is observed that the PID controller experiences low amplitude of vibrations at the head as compared to the passive system. FLC also experiences low amplitude of vibrations at a broader range of frequencies. FLC and PID controller improves amplitude of vibrations at head around 10^{0} Hz regions, which is the most sensitive region related to ears and eyes. Refer Figs. 20 and 21 for time domain results and Fig. 22 for frequency domain results.
Conclusions
This paper presents mathematical modelling, control, and multiobjective optimization of an active nonlinear quarter car suspension system. A nonlinear 2DoF nonlinear quarter car model having quadratic nonlinearities in the tyre and cubic nonlinearity in suspension spring is developed and implemented for control applications.
The PID and FLC strategies are implemented on a nonlinear quarter car system. Controller parameters such as P, I, and D parameters of the PID controller and inputoutput membership functions’ range and scaling factors of the FLC are then tuned using NSGAII algorithm (Table 7). In optimization problem comfort and health criterion consisting of VDV, RMS acceleration, along with stability criterions consisting of suspension space and tyre deflection are used as objective functions. ISO 26311 methodology is adopted and successfully implemented. Numerical simulations show that the GAbased FLC active control system minimizes the frequencyweighted RMS acceleration and VDV as compared to the PID and passive suspension system thus improving the ride comfort. Results are also presented in the frequency domain which shows that the active control system experiences less amplitude as compared to the passive one.
Further results are extended on a human model, which shows that the active control system shows minimum RMS head acceleration, VDV at the head, crest factor, and amplitude ratio at the head and amplitude ration at upper torso, thus providing comfort with health criterion.
Abbreviations
 A_{w} :

Frequencyweighted RMS head acceleration (m/s^{2})
 a_{w} :

Frequencyweighted sprung mass acceleration (m/s^{2})
 c:

Damping coefficient (Ns/m)
 c_{h} :

Cervical spine damping (Ns/m)
 c_{lt} :

Lumber spine damping (Ns/m)
 c_{ut} :

Thoracic spine damping (Ns/m)
 f :

Control force (N)
 f_{obj} :

Objective function
 k:

Stiffness (N/m)
 ke, kec, ku:

Scaling factors for error, change in error, and force respectively
 k_{h} :

Cervical spine stiffness (N/m)
 k_{lt} :

Lumber spine stiffness (N/m)
 Kp, Ki, Kd:

PID gains—proportional, integral, and derivative respectively
 k_{snl} :

Nonlinear spring stiffness (N/m^{3})
 k_{t} :

Tyre stiffness (N/m)
 k_{tnl} :

Nonlinear tyre stiffness (N/m2)
 k_{ut} :

Thoracic spine stiffness (N/m)
 m:

Mass (kg)
 n_{o} :

Reference spatial frequency = 0.1(cycles/m)
 Sq(n_{o}):

Coefficient of road roughness
 v:

Velocity (m/s)
 VDV:

Vibration dose value (m/s^{1.75})
 w(t):

White noise signal having PSD = 1
 x, ẋ, ẍ:

Displacement (m), velocity (m/s), and acceleration (m/s^{2})
 x_{r} :

Road profile (m)
 c:

Seat cushion
 f:

Frame
 h:

Head
 lt:

Lower torso
 s:

Sprung
 t:

Thigh and pelvis
 us:

Unsprung
 ut:

Upper torso
References
Abdelrassoul, R., Ali, Y., & Zaghloul, M. S. (2016). Genetic algorithmoptimized PID controller for better performance of PV system. In Proceedings  2016 world symposium on computer applications and research, WSCAR 2016 (pp. 18–22). https://doi.org/10.1109/WSCAR.2016.14.
Alander, J. T. (1992). On optimal population size of genetic algorithms. In CompEuro 1992 Proceedings computer systems and software engineering (pp. 65–70). https://doi.org/10.1109/CMPEUR.1992.218485.
Amato, F. J. D., & Viassolo, D. E. (2000). Fuzzy control for active suspensions. Mechatronics, 10(8), 897–920. https://doi.org/10.1016/S09574158(99)000793.
Baumal, A. E., McPhee, J. J., & Calamai, P. H. (1998). Application of genetic algorithms to the design optimization of an active vehicle suspension system. Computer Methods in Applied Mechanics and Engineering, 163(1–4), 87–94. https://doi.org/10.1016/S00457825(98)000048.
Boileau, P., & Rakheja, S. (1998). Wholebody vertical biodynamic response characteristics of the seated body biodynamic response under vertical vibration. Journal of Sound and Vibrations, 215(4), 841–862. https://doi.org/10.1016/S01698141(97)000309.
Bouarroudj, N., Boukhetala, D., Djari, A., Rais, Y., & Benlahbib, B. (2017). FLC based Gaussian membership functions tuned by PSO and GA for MPPT of photovoltaic system: a comparative study. In 2017 6th international conference on systems and control, ICSC 2017 (pp. 317–322). https://doi.org/10.1109/ICoSC.2017.7958640.
Bovenzi, M. (2005). Health effects of mechanical vibrations. Giornale Italiano di Medicina del Lavoro ed Ergonomia, 27(1), 58–64.
Celin, P. S., & Rajeswari, K. (2012). GA tuned Type2 fuzzy logic controller for vehicle suspension system. In Proceedings: international conference on computing, electronics and electrical technologies [ICCEET] (pp. 383–388). Kumaracoil. https://doi.org/10.1109/ICCEET.2012.6203863.
Chen, H., & Chang, S. (2006). Genetic algorithms based optimization design of a PID controller for an active magnetic bearing. IJCSNS International Journal of Computer Science and Network Security, 6(12), 95–99.
Deb, K., Pratap, A., Agarwal, S., & Meyarivan, T. (2002). A fast and elitist multiobjective genetic algorithm: NSGAII. IEEE Transactions on Evolutionary Computation, 6(2), 182–197. https://doi.org/10.1109/4235.996017.
Fuller, C. R., Elloit, S. J., & Nelson, P. A. (1996). Active control of vibrations. London: Academic Press.
Gad, S., Metered, H., Bassuiny, A., & Abdel Ghany, A. (2017). Multiobjective genetic algorithm fractionalorder PID controller for semiactive magnetorheologically damped seat suspension. Journal of Vibration and Control, 23(8), 1248–1266. https://doi.org/10.1177/1077546315591620.
He, L., Qin, G., Zhang, Y., & Chen, L. (2008). Nonstationary random vibration analysis of vehicle with fractional damping. 2008 International Conference on Intelligent Computation Technology and Automation (ICICTA), 2, 150–157. https://doi.org/10.1109/ICICTA.2008.348.
HernándezDíaz, A. G., Coello, C. A. C., Pérez, F., Caballero, R., Molina, J., & SantanaQuintero, L. V. (2008). Seeding the initial population of a multiobjective evolutionary algorithm using gradientbased information. In 2008 IEEE congress on evolutionary computation, CEC 2008 (pp. 1617–1624). https://doi.org/10.1109/CEC.2008.4631008.
Holland, J. H. (1975). Adaptation in natural and artificial systems. Michigan: MIT Press.
Holland, J. H. (1992). Genetic algorithms. Scientific American, 267(1), 66–72. https://doi.org/10.1038/scientificamerican079266.
Huang, S. J., & Chao, C. H. (2000). Fuzzy logic controller for a vehicle active suspension system. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 214(1), 1–12. https://doi.org/10.1243/0954407001527178.
ISO 26311 (1997) Mechanical vibration and shock  Evaluation of human exposure to wholebody vibration.
ISO 8608. (1995). Mechanical vibration – Road surface profile – Reporting of measured data (1st ed.).
Kalaivani, R., Lakshmi, P., & Sudhagar, K. (2014). Hybrid (DEBBO) fuzzy logic controller for quarter car model. In Proceedings  UKACC international conference on control (pp. 301–306). Loughborough.
Kesarkar, A. A., & Selvaganesan, N. (2015). Tuning of optimal fractionalorder PID controller using an artificial bee colony algorithm. Systems Science and Control Engineering, 3(1), 99105. https://doi.org/10.1080/21642583.2014.987480.
Li, P., & Du, X. (2006). A GA optimization for FLC with its rule base and scaling factors adjustment. In Proceedings: International Conference on Intelligent ComputingPart II (pp. 1–10). Kunming. https://doi.org/10.1007/11816171_1.
Liu, Y.H., Wang, S.C., & Peng, B.R. (2016). Determining optimal membership functions of a FLCbased MPPT algorithm using the particle swarm optimization method. In Proceedings  2016 5th IIAI international congress on advanced applied informatics, IIAIAAI 2016. https://doi.org/10.1109/IIAIAAI.2016.123.
Lixia, J., & Wanxiang, L. (2008). Chaotic vibration of a nonlinear quarter vehicle model. In Proceedings  IEEE vehicle power and propulsion conference (pp. 1–4). Harbin.
McGee, C., Haroon, M., Adams, D., & Luk, Y. (2005). A frequency domain technique for characterizing nonlinearities in a tirevehicle suspension system. Journal of Vibration and Acoustics, 127(1), 61–76. https://doi.org/10.1115/1.1855931.
Metered, H., Elsawaf, A., Vampola, T., & Sika, Z. (2015). Vibration control of MRdamped vehicle suspension system using PID controller tuned by particle swarm optimization. SAE International Journal of Passenger Cars  Mechanical Systems, 8(2), 01–0622. https://doi.org/10.4271/2015010622.
Nagarkar, M. P., Vikhe Patil, G. J., & Zaware Patil, R. N. (2016). Optimization of nonlinear quarter car suspension–seat–driver model. Journal of Advanced Research, 7(6), 991–1007. https://doi.org/10.1016/j.jare.2016.04.003.
Niu, X. (2014). The optimization for PID controller parameters based on genetic algorithm. Applied Mechanics and Materials, 513517, 4102–4105. https://doi.org/10.4028/www.scientific.net/AMM.513517.4102.
Rajendiran, S., & Lakshmi, P. (2016). Simulation of PID and fuzzy logic controller for integrated seat suspension of a quarter car with driver model for different road profiles. Journal of Mechanical Science and Technology, 30(10), 4565–4570. https://doi.org/10.1007/s1220601609276.
Rosenthal, S., & Borschbach, M. (2014). Impact of population size and selection within a customized NSGAII for biochemical optimization assessed on the basis of the average cuboid volume indicator. In Proceedings  Sixth International conference on bioinformatics, biocomputational systems and biotechnologies (pp. 1–7). Chamonix: BIOTECHNO.
Salem, M. M. M., & Aly, A. A. (2009). Fuzzy control of a quartercar suspension system. World Academy of Science, Engineering and Technology, 53, 258–263.
Song, L. (2011). NGPMA NSGAII Program in Matlab  User Manual. Version 4.1 (pp. 1–20).
Song, L. (2015). NGPMA NSGAII Program in Matlab v14. Matlab Code. http://in.mathworks.com/matlabcentral/fileexchange/31166ngpmansgaiiprograminmatlabv14. Accessed on 15 Mar 2015.
Talib, M. H. A., & Darus, I. Z. M. (2014). Development of fuzzy logic controller by particle swarm optimization algorithm for semiactive suspension system using magnetorheological damper. WSEAS Transactions on Systems and Control, 9, 77–85.
Tammam, M. A., Magdy, A. S., Aboelela, M. A., Moustafa, & Seif, A. E. A. (2013). A multiobjective genetic algorithm based PID controller for load frequency control of power systems. International Journal of Emerging Technology and Advanced Engineering, 3(12), 463–467.
Taskin, Y., Hacioglu, Y., & Yagiz, N. (2007). The use of fuzzylogic control to improve the ride comfort of vehicles. Strojniski Vestnik/Journal of Mechanical Engineering, 53(4), 233–240.
Taskin, Y., Hacioglu, Y., & Yagiz, N. (2017). Experimental evaluation of a fuzzy logic controller on a quarter car test rig. Journal of Brazilian Society of Mechanical Science and Engineering, 39(7), 2433–2445. https://doi.org/10.1007/s4043001606370.
Van Niekerk, J. L., Pielemeier, W. J., & Greenberg, J. A. (2003). The use of SEAT effective amplitude transmissibility (SEAT) values to predict dynamic seat comfort. Journal of Sound and Vibration, 260(5), 867–888. https://doi.org/10.1016/S0022460X(02)009343.
Wong, J. Y. (2001). Theory of ground vehicles. NY: Wiley.
Zhang, Y., Chen, W., Chen, L., & Shangguan, W. (2007). Nonstationary random vibration analysis of vehicle with fractional damping. In Proceedings  13th national conference on mechanisms and machines (NaCoMM07) (pp. 171–178). Bangalore.
Zhu, Q., & Ishitobi, M. (2006). Chaotic vibration of a nonlinear fullvehicle model. International Journal of Solids and Structures, 43(3–4), 747–759. https://doi.org/10.1016/j.ijsolstr.2005.06.070.
Acknowledgements
The first author likes to express his deep gratitude towards the management of Ahmednagar Jilha Maratha Vidya Prasarak Smamaj, Ahmednagar, and likes to thank the Principal, SCSMCoE, Ahmednagar, for their encouragement and constant support to carry out this research work. The first author also likes to thank Springer Nature and Springer Nature Waiver team for their generous help and constant support during this work.
Funding
Not applicable.
Availability of data and materials
Not applicable.
Author information
Authors and Affiliations
Contributions
MPN has been involved in the optimization, simulation, and drafting. YJB, GJV, and RNZ have been involved in the drafting of the manuscript and revising it critically for important intellectual content. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare that they have no competing interests.
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Nagarkar, M.P., Bhalerao, Y.J., Vikhe Patil, G.J. et al. GAbased multiobjective optimization of active nonlinear quarter car suspension system—PID and fuzzy logic control. Int J Mech Mater Eng 13, 10 (2018). https://doi.org/10.1186/s4071201800968
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s4071201800968