Introduction

The campaign against anthropogenic climate change faces society with the challenge of fully defossilizing the energy system [93], including not only power generation, but also the transportation, heat supply, agricultural, and industrial sectors. Technologies that use renewably produced power in other sectors are referred to as power-to-x. Among these concepts, power-to-fuel describes a concept whereby power is utilized to produce substances that can be used as alternative fuels in combustion engines for road transport. As these fuels are produced synthetically, their chemical structure is not restricted to a natural distribution, as it is the case with crude oil. When choosing a synthesis product for use as a transport fuel, the following characteristics should be taken into account:

  • Efficiency and economy of the production process

  • Combustion characteristics inside the engine

  • Compatibility with current handling systems (stationary infrastructure and mobile storage)

  • Ecological aspects (e.g., toxicity, safety, or greenhouse gas potential)

Schemme et al. suggest arranging the possible synthetic transport fuels into the following subgroups [76]:

  • Alkanes by Fischer-Tropsch reactions

  • Hydrocarbons by oligomerization

  • Alcohols

  • Ethers

While all types of fuels exhibit different physical characteristics, all have in common that they can be produced from the two-feed chemicals of hydrogen and carbon dioxide within the power-to-fuel approach. Both substances must be obtained in a sustainable manner, so that the resulting synthetic fuels can contribute to defossilization. Hydrogen can be produced via water electrolysis using renewable power sources such as wind, solar, or hydro [22]. CO2 can be obtained from non-fossil sources, such as the process emissions of industrial plants [6], biomass [88], or even direct air capture [35].

The use of decentralized sources of carbon dioxide and hydrogen is of great importance in a future energy system. Synthesis, storage, and transport are central questions when selecting suitable substances that can be produced on-site and then transported away using a suitable infrastructure. First, it must be clarified whether fuels from biomass and hydrogen can potentially make a significant contribution to the energy transition. In the selection, the basic design of the synthesis and thermodynamic analyses, such as process design, is decisive. The handling of chemicals and gases is of great importance on a farm. Therefore, the socio-economic aspects of the preselected fuels are closely examined.

Potential of fuels from biomass

Numerous studies have estimated global biomass potential. Offermann et al. analyzed and summarized 19 studies [65]. According to their literature review, the global potential was found to range between 0 and 1550 EJ/a for the year 2050. Within their analysis method, the concluded potentials are divided into 200–600 EJ /a for energy plants and 62–325 EJ/a for residual materials [7]. The global biomass potentials are very unequally distributed. Asia, Africa, and South America hold the highest potential, while Europe, North America, and the Pacific only contribute a small extent to the overall potential. To classify these figures, only 49 EJ of the total energy demand of 503 EJ, i.e., 9.74%, were based on biomass in 2007. The share of bio energy has not changed from 2007 to 2016 while the total energy demand worldwide increased about 15%. In 2016, 56 EJ of bio energy contributed to a total demand of 576 EJ, i.e., 9.77% [41]. Estimates vary widely, as there are many uncertainties regarding the use of uncultivated land (0–580 Mha) and congestion externalities. Berndes et al. drew on 17 studies for their analysis [5]. They estimated global biomass potentials to range between 100 and 400 EJ/a, from which 50–240 EJ/a was based on energy crops. The main biomass source is wood. The potentials were estimated at a maximum of 115 EJ/a in 2050, also with a focus of production in Asia, Africa, and South America. Parrika also estimates the potential at 100 EJ/a, with about 41.6 EJ/a for wood [66]. A share of 40 EJ/a of global biomass was found to be used for energy. The focus is also in Asia, with 60%. In Europe, the potential for energy from biomass is 8.9 EJ/a, with a breakdown into 4 EJ/a wood, 2.6 EJ/a energy crops, and 1.6 EJ/a straw and accounting for approximately 10% of the global potential.

Kaltschmitt et al. assess initially biomass potentials and subsequently, the prospects for usage [47]. They break down potentials into 12 segments in which gas was not analyzed. High potential (almost 75%) was identified for wastes and residues, i.e., in the segments of excrement and litter (~ 67%), harvest residues, waste from trade and industry, and organic municipal residues. Regional differences presumably play a large role here. Without the cultivation of energy crops, Kaltschmitt et al. expect a potential of 960–1050 PJ/a, representing 741–770 PJ/a for thermochemical conversion and 219–280 PJ/a for biochemical conversion [47]. The resulting final energy potentials for fuels are 71–145 PJ/a available as straw-like waste and 225–394 PJ/a as woody waste. An additional 111–162 PJ/a also arises from the biochemical conversion of waste where methane is the end product. In addition to the potential of biomass waste, Kaltschmitt et al. estimated a land availability of 2 mil ha for energy crops in Germany [47]. In combination with the cultivation of short-rotation coppice, e.g., poplar trees, a harvest rate of 12 t/ha/a can be achieved leading to 24 Mt wood/ a. Putting the focus on Miscanthus grass, Christian et al. reported an average yield of about 12.8 t/ha [15].

A further focus can be set on wood and straw gasification as part of the 12 segments defined in Kaltschmitt et al. [47]. According to a process analysis from Grube et al., the CHOREN/FT process results in a 200 kg/h fuel mix from 1 t/h wood with a focus on diesel and kerosene (about 154 kg/h) [37]. The resulting final energy potential for this process chain is 206 PJ/a, corresponding to 4.8 Mt fuel/a. Kerdoncuff calculated in 2008 for the evaluation of the BioLiq-process with a fuel production rate of 60–70 kg/h out of 1 t/h of residual wood and 115 kg/h fuel out of 1 t/h of residual straw [48]. Trippe worked with a rate of 106 kg/h out of 1 t/h residual straw for his techno-economic analysis [87]. According to the data of Dahmen and Sauer, the fuel production rate could be increased to 133 kg/h out of 1 t/h residual straw [16]. In turn, combining 2 mio. ha with 12 t biomass /ha and those conversion rates lead to fuel energy potential between 140 and 205 PJ/a corresponding to 3.2–4.8 Mt fuel/a in good accordance with the values of Kaltschmitt et al. [47].

The addition of hydrogen can improve the efficiency of fuel production from biomass. Dietrich et al. [19] combined the biofuel processing with electrofuel production from renewable hydrogen and CO2 within their cost analysis. In comparison, Gale et al. reported a value of 90.6 Mt/a CO2 emissions from bioenergy and fermentation which can be taken into account [30]. This amount can be supplemented by electrofuels with CO2 from industrial sources. Gale et al. listed numerous industrial CO2 sources with average emissions of between 0.58 and 3.94 Mt CO2 per anno and per source, such as fossil-based power plants (mostly coal), cement production, refineries, integrated steel mills, and petrochemical processes for ethylene and ammonia synthesis. Currently, steel makers are considering the reduction of iron by hydrogen while the cement industry still relies on limestone. Furthermore, Billig et al. identified cement industry and biomass fermentation as future CO2 feedstocks for electrofuels [6]. Billig et al. also analyzed the potential of 5.2 Mt CH4 and 11.9 Mt CO2 from about 9000 fermentation plants, including biogas upgrading in Germany, leading to 260 PJ/a. An additional quantity of 4.1 Mt CH4 could be synthesized from CO2, combined with 2.2 Mt hydrogen from wind. The feedstock for such plants will be shifted from energy crops to residual biomass, such as straw and dry and liquid manure and waste streams. Finally, the potential of methane from fermentation could reach 9.3 Mt CH4, directly and indirectly via CO2 methanation, corresponding to 465 PJ/a in 2050. Billig et al. reported a slightly decreasing CO2 foot print in the cement industry, with 15.1 Mt/a in 2050, resulting in 5.5 Mt CH4/a [6]. Finally, the CH4 potential consists of 5.4 Mt/a of bio-methane and, additionally, 9.6 Mt/a via CO2 methanation from CO2 separated from the cement industry and biogas. The H2 demand for both CO2 sources amounts to 4.8 Mt/a in 2050. The total energy of methane adds up to 750 PJ/a.

In order to compare these values, the demand for middle distillates in Europe amounted to 256.7 million t/a diesel and 40.4 million t/a kerosene [29] in 2016. This equates to annual energy volumes of 8.6 EJ for diesel and 2.2 EJ kerosene. In Germany, 37.9 Mt of diesel and 9.2 Mt of jet fuel were consumed in 2016, corresponding to 1630 PJ/a diesel and nearly 400 PJ/a jet fuel [59]. The analyzed amount of potential biogas in Germany—from fermentation and the power-to-gas route of the by-product CO2—could meet a large share of today’s diesel demand if compressed natural gas or liquefied natural gas can be introduced in the mobility sector as widespread fuels.

Unfortunately, the economic aspects of synthetic methane offer poor prospects for widespread market introduction. Different research groups have published techno-economic analyses for power-to-gas and biogas synthesis plants [31, 32, 36, 38, 60, 61]. Gassner and Maréchal designed the operation of their methanation unit to achieve 1.47 €/kg [31, 32]. Meanwhile, Peters et al. analyzed costs of 3.8 €/kg for CO2 from fermentation and H2 from wind energy via electrolysis and 1.8 €/kg for CO2 and H2 from biomass [70]. Brynolf et al. analyzed several studies in a review paper and noted methanation costs by anaerobic digestion in a broad range of 0.13–2.5 €/kg and 1–1.2 €/kg by means of the gasification of lignocellulose [8]. Electricity and/or hydrogen cost assumptions play a crucial role. Tremel et al. reported specific costs of about 0.169 €/kWh, corresponding to 2.34 €/kg at hydrogen costs of 3 €/kg [86], while Peters et al. assumed 5.5 €/kg [70]. The electricity price of 14 $/GJ, taken from Hannula leads to an extremely low hydrogen cost of about 2.7 €/kg H2 for an electrolyzer efficiency of 62% [38]. Hannula reported thermochemical methanation costs of about 0.9 €/kg and 1.85 €/kg for the electrochemical pathway. Approximating these different assumptions led to the conclusion that the cost data fits very well to the gasification and power-to-gas routes. In order to classify these costs, the external gas price without taxes at the German border amounts to 2 €-cent/kWh, corresponding to a value of 0.25 €/kg of natural gas. Finally, there is a large hurdle to switch from fossil fuels to bio-methane or power-to-gas.

Otherwise, the ecological aspects indicate an extremely positive outlook for bio-methane from liquid manure fermentation. As analyzed by Peters et al., the CO2 footprint for the fossil natural gas used in automotive applications increases from 54.8 to 70.2 g CO2/MJf due to methane slip resulting from exploration, transport, storage, and usage in transportation [70]. Renewable pathways such as municipal waste gasification result in 12.1 g CO2/MJf. The fermentation of liquid manure gets high credit if it is not distributed on cultivated land. In combination with hydrogen from wind energy via electrolysis, CO2 methanation can achieve a credit of − 78.1 g CO2/MJf for the entire chain. Todays a feedstock mixture of liquid manure, biomass waste and silage is used for fermentation leading to a mixed value for the CO2 footprint. For a small 75 kWe unit, a mix of 3300 t of cattle manure and 790 t corn silage is proposed on a yearly base [91]. For a larger 500 kWe unit, the relation is shifted toward silage of different sources and cattle manure, i.e., 8700 and 2200 t on a yearly base, respectively.

A huge advantage of bio fermentation plants is that they already exist, while large-scale gasification for residual wood and straw has not yet left the pilot plant stage. It makes sense to implement these small units into a future renewable energy system. In regard of the negative impact of fertilization with manure on the soil, it makes sense to increase the number of biogas plants or to build-up new larger facilities. Today, only 30% of the manure volume was used in fermentation [3, 89]. An amount of 200 m3 liquid manure from 300 m3 in total is used for fertilization. If the share of biogasification should be increased up to 60%, two related issues come up: (a) Is there a need to increase the amount of silage in parallel or could the mixture be changed towards more manure? (b) What should be made with the higher amount of biogas? In 2016, about 9000 fermentation plants could be found in Germany; only less than 200 offered a biogas upgrade to bio-methane and grid connection [3, 6, 24, 25, 89, 91]. In regard to storage and transport, a liquid fuel is preferred. A techno-economic analysis of methanation is already performed by Peters et al. [70]. It was shown that the economic prospects of a widespread usage in relation to today’s natural gas cost are very difficult for an adequate market introduction. The questions that arise, however, include what else can be synthesized from CH4/CO2-mixtures at reasonable costs? Which plant configuration is best to implement on farm sites?

Decker et al. present a design of a small-scale plant for the production of synthetic fuels, including a transient simulation of the operation and a subsequent economic evaluation of the designed system [18]. Taking the transient nature of the system into account is crucial for its design, as the allocation of both hydrogen and carbon dioxide from biogas is discontinuous. The fuel production pathways that have been evaluated were Fischer-Tropsch and methanol synthesis due to the lower number of process steps compared to other synthesis products [74, 75] and, therefore, favorable economic performances [8]. For a broader implementation, a suitable fuel with high energy density should be chosen that can easily be transported to a central refinement plant for subsequent upgrading steps up to a standardized transport fuel. Alternatively, an intermediate with the same properties can be produced on a farm site and then transported to a central site where the final fuel can be produced.

This paper covers the selection process of the different fuel types in detail. Technical aspects like production, utilization, and handling are evaluated by means of a thermodynamic analysis. Based on this analysis, the ecological and economic aspects will be evaluated to yield a set of recommendations of suitable synthetic transport fuels produced in decentralized plants with CO2 supply from biogas plants.

Basic fuel synthesis design

This section’s basic fuel synthesis design discusses aspects of hydrogen and carbon dioxide provision. Hydrogen will be produced via electrolysis using renewable electricity from wind farms. Carbon dioxide can be separated from biogas plants after the fermentation of biomass. Bio waste and (liquid) manure should preferably be used due to the recent trend in biogas subsidization of waste products in Germany and the debate about food versus fuel.

An alternative could be the implementation routes of bio catalytic activation. A coupling of the power-to-fuel concept directly with such pathways might be useful but is still an open research field for further studies in future.

Hydrogen production from wind turbines via electrolysis

Given the fluctuating nature of wind and solar energy, hydrogen production based on those renewable energy sources follows a highly dynamic provision profile. Electrolysis systems can handle this fluctuating income of electricity sufficiently, but subsequent chemical production processes require constant raw material flows for synthesis reactions. Therefore, hydrogen storage systems must be implemented. The upper part of Fig. 1 shows a general process scheme for hydrogen production and storage from wind energy via electrolysis or from the electric grid. Wind power data were modeled according to data from Decker et al. for the different locations, here shown for Cuxhaven in Germany on the basis of weather data from 2013 [18]. Wind data from Cuxhaven offers about 2818 full load hours, representing a good location for electricity production. The lower part of Fig. 1 shows modeled time-dependent values for electric power generation and hydrogen production as a lower heating value (LHV) for the time period 31.5.–6.6.2013 and underpins the concept of power-to-X solutions: At the beginning of this selected week, some peaks with high electricity output from the wind turbine occur, achieving values of over 3.5 MWe for short time periods. The third day (3648–3672 h) is the best day of this week, with values between 2.5 and 4.1 MWe, but mostly above 3.5 MWe. At the end of the week, only short periods with 2 MWe were achievable. Power-to-x offers different concepts for the management of such complex energy systems, so that the electricity generated from renewables can be used as a reliable pillar in a stable and sustainable energy system, despite its fluctuating character.

Fig. 1
figure 1

General process scheme for hydrogen production and storage from wind energy via electrolysis or from the electric grid. Wind power data were modeled according to data from Decker et al. for different locations, here: Cuxhaven in Germany, based on weather data from 2013 [18]. A Electricity from the grid; B–D electricity from the wind park: only surplus of electricity (B), the load regime for electrolysis between the base load of the grid and curtailment at an upper limit (C) and full spectrum to high electricity generation with curtailment at a lower limit and (D) as off-grid electricity supply

The concept of Decker et al. applies PEM electrolysis for hydrogen production in four different operation modes A–D (see the upper part of Fig. 1) [17, 18].

Mode A

Mode A constantly uses electricity from the grid with a mixed share of renewables and fossil-based primary energy. The blue electric line of mode A in Fig. 1 is chain dotted, i.e., “∙−∙−∙−,” Consequently, CO2 reduction targets are only achievable if the share of renewables for electricity production is high and corresponding storage technologies for re-electrification are implemented. Modes B, C, and D represent the renewable modes and are therefore combined in the general process scheme. The differences between the different modes are explained using the example wind power data presented in the lower part of Fig. 1.

Mode B

Mode B uses only those peaks in the electric grid that occur if the integral renewable electricity is higher than the current demand. Presently, this situation seldom appears with today’s medium share of renewables. The electric line of modes B–D are drawn continuously in blue in Fig. 1.

Mode C

Mode C assumes a well-settled network of wind parks, electrolyzers, hydrogen storage systems, and hydrogen supply by pipeline in Germany for 2050, according to the work of [71]. In such a system, wind turbines produce electricity for the currently occurring demand from the electric grid and above (range C in Fig. 1) for hydrogen production via electrolysis. A curtailment of all of the wind energy was implemented to limit investments in light of a techno-economic assessment.

Mode D

Mode D foresees the small-scale usage of wind energy and an adapted hydrogen storage concept with a curtailment at low loads. Different hydrogen storage concepts can be considered: salt caverns locally used (i); salt caverns inclusive of H2 pipelines for cross-regional transport (ii); liquid organic hydrogen carriers (LOHCs) [85] (iii); liquid hydrogen storage (iv); and, finally, gaseous hydrogen storage (v). In this paper, the small-scale operational mode (D) is combined with the storage option in salt caverns (i) in accordance with the recommendation of Decker et al. [17, 18]. In the following, this setup will be referred to as “D-i.”

CO2 capture from biogas plants

Currently, biogas can be directly burned in a stationary internal combustion engine that is mechanically connected to an electric generator and heat supply for stables and other facilities. If methane is fed into the natural gas grid, CO2 must first be separated from the biogas and then the gas has to be upgraded to natural gas quality.

Szarka et al. reported on a flexible, demand-oriented power supply by means of bio energy [84]. More detailed information on the dynamic operation mode of fermentation can be found in Jacobi and Thrommler [45]. The process of gas production can be controlled among other factors by the feeding times of the biogas plant. Three different substrates lead to fast, medium, or slow digestion and a corresponding time from feeding to manure origination. Figure 2 shows the general process scheme for CO2 provision from liquid manure from biomass fermentation. The dynamic profile for biogas generation for 1 week was sketched in accordance to Jacobi and Thrommler [45]. A constant biogas provision can be guaranteed by implementing a large vessel, while a flexible operation mode allows for a smaller biogas storage vessel. Recently, biogas plants tend more toward a flexible operation; however, the concept that is proposed in this paper prefers constant biogas provision. In combination with the D-i concept for hydrogen production, constant fuel production can be achieved. The local fuel synthesis ideally produces a liquid intermediate that can be further processed at a central fuel production facility. The combination of wind energy and fermentation allows for greater flexibility in system design that is partly caused by different pre-processing units.

Fig. 2
figure 2

General process scheme for CO2 provision from liquid manure by biomass fermentation. Dynamic profile for biogas generation for one week according to [45]

Figure 3 shows the general process scheme for using methane and carbon dioxide from biogas for synthetic fuel production. Carbon dioxide can be separated in front of the combined heat and power plant (CHP) to get pure CO2 for the synthesis process. The option is indicated by a continuous line in Fig. 3. The first system draft combines the separated CO2 with renewable hydrogen that is generated by means of electrolysis using electricity from the wind park to form a fuel according to Eq. (1). Water must also be provided, and partly can be recovered from subsequent process steps such as reverse water gas shift and after appropriate cleaning. A second option is to separate CO2 behind the internal combustion engine (ICE) as post-combustion, whereby the specific effort is more caused by dilution with nitrogen, excess air, and water. This path is indicated by a dotted line.

Fig. 3
figure 3

General process scheme for using methane and carbon dioxide from biogas for synthetic fuel production

The mixture of hydrogen and carbon dioxide is conducted in a synthesis unit (a) that is able to convert CO2 and H2 into certain kinds of fuels, X.

$$ \mathrm{n}\ {\mathrm{CO}}_2+\left(\frac{\mathrm{m}}{2}+2\ \mathrm{n}-\mathrm{l}\right){\mathrm{H}}_2\leftrightarrow {C}_n{\mathrm{H}}_m{\mathrm{O}}_l+\left(2\ \mathrm{n}-\mathrm{l}\right)\ {\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}<0\ \mathrm{kJ}/\mathrm{mol} $$
(1)

Fischer-Tropsch synthesis requires carbon monoxide as an educt:

$$ \mathrm{n}\ \mathrm{CO}+\left(\frac{\mathrm{m}}{2}+\mathrm{n}-\mathrm{l}\right){\mathrm{H}}_2\leftrightarrow {C}_n{\mathrm{H}}_m{\mathrm{O}}_l+\left(\mathrm{n}-\mathrm{l}\right)\ {\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}<0\ \mathrm{kJ}/\mathrm{mol} $$
(2)

Therefore, a reverse water-gas shift reactor must be implemented in front of a synthesis unit B, see Eq. (3). Water must be separated in front of synthesis unit (b).

$$ {\mathrm{CO}}_2+{\mathrm{H}}_2\leftrightarrow \mathrm{CO}+{\mathrm{H}}_2\mathrm{O}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=41.17\ \mathrm{kJ}/\mathrm{mol} $$
(3)

A further option is direct reforming of methane with carbon dioxide according to Eq. (4) (dry reforming).

$$ {\mathrm{CO}}_2+{\mathrm{CH}}_4\leftrightarrow 2\ \mathrm{CO}+2\ {\mathrm{H}}_2\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=246.97\ \mathrm{kJ}/\mathrm{mol} $$
(4)

During direct reforming of methane, no water will be formed. Neglecting the occurrence of the water-gas shift reaction which occurs in reality it is theoretically possible to avoid the implantation of a water condenser.

In the next section, the thermodynamic conditions will be discussed for reactions (1)–(4). The following research questions arise from the considerations outlined above:

  • What size of equipment should be installed?

  • Which fuel should be preferentially produced?

  • What kind of system must be foreseen as decentralized installation?

To answer these questions, general thermodynamic methods, insights from process analysis, basic economic calculations, and socio-economic aspects must be taken into account.

Thermodynamic analysis

In this section, different thermodynamic analysis methods are compiled to evaluate different process chains for electrofuel production. In the first section, syngas production considers a pre-reaction of hydrogen and carbon dioxide or methane and carbon dioxide in order to form a typical syngas mixture consisting of hydrogen and carbon monoxide. A brief analysis of options for the direct synthesis of electrofuels from hydrogen and carbon dioxide, or from syngas, follows. Considering the claim of a product or intermediate with a high power density prefers the selection of a liquid. Fischer-Tropsch synthesis primarily leads to alkanes with chain lengths up to waxes. Additionally, the process for achieving diesel fuel is fairly complex.

The next section applies a simplified Gibbs energy analysis for the production of octanol and OME3-5 mixtures as optional substitutes for diesel fuel. Subsequently, a process analysis evaluates the complexity of different process chains. Finally, selected electrofuels will be considered for the optimization of synthesis routes. On the basis of this evaluation procedure, selected electrofuels pass to the next evaluation step, i.e., a socio-economic analysis.

Syngas production

The operation parameters for syngas production by reverse water-gas shift reaction, Eq. (3), and dry reforming, Eq. (4), were determined by chemical equilibrium calculations. At high pressures, the ideal gas state relation must be replaced by an equation that describes the real gas behavior. An overview of the development of such equations was given in 1993 by Soave [81]. In this paper, a modification of the original Redlich-Kwong equation is applied for the thermodynamic gas phase description already made by Soave in 1972 [82]. This equation of state is termed in the following sections as the Soave-Redlich-Kwong (SRK) equation of the state or equation of state (EOS) SRK.

Figure 4 shows the chemical equilibrium of the reverse water-gas shift reaction (rWGS) at 1 bar. It is also important to note that a conversion higher than 80% is only achieved at temperatures higher than 1173 K. Unconverted H2/CO2 can be recycled but the recycle loop flow increases strongly with decreasing conversion. For the synthesis of methane, an educt mixture of H2:CO of 3:1 is required, while for butane this ratio amounts to 9:4. The chemical equilibrium at 1473 K for an educt mixture of H2/CO2 = 4 offers a product mixture of 75.6% H2 and 21.6% CO in a dry state, i.e., H2/CO = 3.46. An educt mixture of H2/CO2 = 3 leads to a product mixture of H2/CO = 2.45. In order to avoid carbon deposits, it is practical to give some hydrogen in excess.

Fig. 4
figure 4

Chemical equilibrium of reverse water-gas shift reaction at 1 bar for two educt mixtures H2/CO2 = 4 and H2/CO2 = 3. Red-colored background: low conversion; green colored background: high conversion (goal)

Figure 5 shows the chemical equilibrium of dry reforming at 2 bar. An ideal mixture for a gas fermenter is a gas mixture of methane to carbon dioxide of 1:1. At temperatures of 1073 K, conversion higher than 80% will be achieved. The hydrogen to carbon monoxide ratio in the product gas amounts to 1:1. Finally, after the dry reforming, extra hydrogen must be added to this mixture to fulfill the conditions of fuel synthesis. Biogas mostly offers a surplus of methane, for example 60% (Vol.), leading to a ratio of CH4/CO2 = 1.5. In such cases, conversion drops to values below 65%. It is important to note that the endothermic heat of reaction for the case of dry reforming is high, with values of about 200 MJ/kmol syngas related to 40 MJ/kmol for the reverse water-gas shift reaction, see Fig. 6. For rWGS and dry reforming, educt gases must be heated to above 1000 K, with additional thermal energy supplied under such reaction conditions. The product gas should then be cooled down to the reaction temperature of the synthesis reaction. This allows heat recuperation for pre-heating the educts. With regard to the goal of GHG emissions reduction, no fossil fuel should be burnt.

Fig. 5
figure 5

Chemical equilibrium of dry reforming according to Eq. (4) at 2 bar for two educt mixtures CH4/CO2 = 1.5 and CH4/ CO2 = 1. Red-colored background: low conversion; green-colored background: high conversion (goal)

Fig. 6
figure 6

Comparison of reverse WGS with dry reforming at 2 bar and 1173 K for the educt mixtures H2/CO2 = 4 (left) and CH4/ CO2 = 1 (right)

In the case of a gas fermenter, a part of the biogas can be used or direct electrical heating using renewable electricity from a wind turbine can guarantee a low-CO2 footprint for the concept. The efficiency of syngas production is defined as the lower heating value of the product gas times the amount of produced gas divided by the sum of the lower heating value of the educt gas, times the educt gas amount and the heat input, as shown in Eq. (5):

$$ {\eta}_{PTL}=\frac{{\dot{m}}_{Fuel}\cdotp {H}_{u,K}}{\frac{{\dot{m}}_{H2}\cdotp {H}_{u,H2}}{\eta_{H2}}+{P}_{CO2}+{P}_A} $$
(5)

This efficiency is high for rWGS, i.e., 96% and much lower for dry reforming with 57% due to the high heat of the reaction. The H2 balance of rWGS shows that a high share of 20.8% is lost by the chemical reaction and only 3.9% of the hydrogen can be used for the heat supply if this would be taken into account for delivering the heat of reaction of rWGS. Figure 6 visualizes the above-presented comparison between the two process routes.

From the preceding section, it can be concluded that syngas production for fuel synthesis is favorably performed by the reverse water-gas shift reaction.

Direct synthesis

A more advantageous option would be the direct synthesis from CO2 and H2. In order to check the capability of realizing direct synthesis, Peters [69] developed a method for methanol, dimethyl ether, and polyoxymethylene dimethyl ether (OME) by applying the equations of state by Soave [82] and Peng and Robinson [67] for real gases at high pressures. A simplified check can be done by assuming ideal gas conditions. At standard conditions, i.e., p = 1.013 bar and T = 298.15 K, a first impression of the ability of a chemical reaction can be reached. Catalysts demand an individual ignition temperature to catalyze a chemical reaction. Additionally, a pressure increase enhances the chemical reaction if the number of moles decreases during the chemical reaction, according to the principle of Le Chatelier (see Smith and van Ness [80].

The free enthalpy or Gibbs energy (G) is considered a criterion for the spontaneity of a reaction and is negative for any spontaneous chemical reaction [80]. If a reversible reaction is considered, as is the case for fuel synthesis from CO2 and H2, the Gibbs energy can be used as a measure of the chemical equilibrium; see [69]. The total Gibbs energy (GM) of a mixture is defined by the sum of the chemical potentials of all participating species N [80].

$$ {G}_{\mathrm{M}}=\sum \limits_{\mathrm{j}=1}^{\mathrm{N}}{\mathrm{n}}_{\mathrm{j}}{\upmu}_{\mathrm{j}} $$
(6)

with GT: [J]; ni: molar number of species i [mol]; μi: chemical potential of species i [J/mol]. Gibbs energy can be calculated for each species by the following:

$$ {G}_j={H}_j-T\ {S}_j $$
(7)

The values for enthalpy Hj and entropy Sj were calculated as temperature-dependent expressions by Perry and Green [68]. The resulting Gibbs energy incorporates the stoichiometry of the individual chemical reactions and ideal mixing rules. It is assumed that all chemical reactions would be performed until conversion to the product reached 100%. Restrictions from chemical equilibrium were not considered in the simplified comparison method. Standard temperature and pressure, i.e., 298.15 K and 1 bar was set for the first step. Two cases were analyzed: (a) complete fuel synthesis from CO2/H2; and (b) complete fuel synthesis from CO/H2. This kind of Gibbs energy analysis will be applied to alkanes, ethers, and alcohols of different chain lengths. Figure 7 shows the results of a Gibbs energy analysis for direct synthesis of various fuels from H2/CO2 and H2/CO mixtures at 1 bar. The number of carbon atoms is sketched on the x-axis. If the change in Gibbs energy is near zero—as is the case for methanol synthesis—an equilibrium conversion of roughly around 50% can be expected. In this instance, an accurate determination of the chemical equilibrium under reaction conditions with a real gas model for high pressures must be performed, as reported by Peters [69]. More details and limitations about the simplified comparison method are also published in [69]. Alkanes can be synthesized by the Fischer-Tropsch process. The chain growth, in turn, can be described by a Schulz-Flory model. Details on the possible mechanism and technical realization are presented by Dry [20]. Figure 7 shows that the change in Gibbs energy increases with increasing chain length. From a practical point of view, Fischer-Tropsch processes end up with wax, which must be cracked to shorter hydrocarbons and subsequently distillated to achieve standard cuts, such a naphtha, kerosene, and diesel. Synthesis paths for higher alcohols were analyzed by Schemme et al. [75]. The simplest alcohol methanol can be produced directly from CO2 and CO. However, as stated by Subramani and Gangwal [83] and He [39], the direct pathway via CO2 hydrogenation is already complex for the C2-alcohol ethanol. It suffers from a low selectivity and low conversion rate. Other routes include modified methanol and Fischer-Tropsch processes, such as the Ziegler process of mixed alcohol synthesis and aldol or oxo synthesis [75]. Oxo synthesis adds a syngas with carbon monoxide and hydrogen to an olefin and achieves an aldehyde that will be hydrogenated to corresponding alcohols. This route fits perfectly to the intermediates of today’s chemistry.

Fig. 7
figure 7

Gibbs energy analysis for the direct synthesis of various fuels from H2/CO2 (left) and H2/CO (right) mixtures at 1 bar. Red-colored background: low conversion; green-colored background: high conversion (goal)

The Ziegler process is based on the oligomerization of ethylene, resulting in a broad range of linear alcohols, as stated by Behr and Falbe [4, 26]. As in the case of the modified methanol and Fischer-Tropsch process, the Ziegler process leads to insufficient selectivity.

As was mentioned earlier, the direct synthesis of methanol, dimethylether (DME), and methylal (OME1) was analyzed by a thermodynamic model using equations of state (Soave Redlich Kwong [82], Peng Robinson [67], and Gibbs energy analysis by Peters [69]). Methylal can only be synthesized if byproducts such as DME and methanol are suppressed by an applicable catalyst. Reaction conditions are quite unfavorable with 100 bar and 413 K and catalyst activity will not be high at such low temperatures. These results were supported by the relationship between the Gibbs energy change for direct OMEx synthesis with growing chain length x; see Fig. 7. With increasing carbon chain length, the change in Gibbs energy increases. The values are mostly positive, indicating low conversion for direct OMEx synthesis.

All direct synthesis reactions can be forcibly ramped-up by changing the starting educt molecule from CO2 to CO, which is the commonly used carbon carrier in syngas reactions. The disadvantage of using carbon monoxide for synthesis while starting from carbon dioxide is the implementation of rWGS; see also the chemical equilibrium conditions in Fig. 4. Today, Fischer-Tropsch catalysts only exist for syngas that contains CO. Therefore, rWGS is essential for such a system.

Indirect synthesis of diesel substitutes

The power-to-fuel concept incorporates technologies such as carbon capture utilization and storage (CCUS), sector coupling in the energy and mobility sectors, and fosters the expectation that cleaner fuels eliminate emissions in transportation. Schemme et al. analyzed the power-to-fuel concept as a key to sustainable transport systems, especially for diesel fuels [76]. Potential candidates include OME3-5 and octanol. In this contribution, it should be determined whether these fuels are the optimal ones for renewable fuel production at farm sites. If not, the next research question would be which intermediates are better suited for decentralized production and for subsequent processing at a central site.

Burger described different process routes for the formation of mixtures of polyoxymethylene dimethyl ethers [9]. In this contribution, a process route via the intermediates of trioxane and methylal (route B as proposed by Burger [9]) was chosen. Firstly, methanol is formed at 80 bar and 523 K:

$$ {\mathrm{CO}}_2+3\ {\mathrm{H}}_2\leftrightarrow {\mathrm{CH}}_3\mathrm{OH}+{\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-49.2\ \mathrm{kJ}/\mathrm{mol} $$
(8)

An important intermediate is formaldehyde, formed by the partial oxidation of methanol at 1 bar and 903 K:

$$ {\mathrm{CH}}_3\mathrm{OH}+\frac{1}{2}\ {\mathrm{O}}_2\leftrightarrow {\mathrm{CH}}_2\mathrm{O}+{\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-156.7\ \mathrm{kJ}/\mathrm{mol} $$
(9)

Formaldehyde and two molecules of methanol react to methylal at 2 bar and 33 K:

$$ 2\ {\mathrm{CH}}_3\mathrm{O}\mathrm{H}+{\mathrm{CH}}_2\mathrm{O}\leftrightarrow {\mathrm{CH}}_3\mathrm{O}{\mathrm{CH}}_2\mathrm{O}{\mathrm{CH}}_3+{\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-56.1\ \mathrm{kJ}/\mathrm{mol} $$
(10)

In parallel, three molecules of formaldehyde form the intermediate trioxane at 1 bar and 343 K.

$$ 3\ {\mathrm{C}\mathrm{H}}_2\mathrm{O}\leftrightarrow {\mathrm{C}}_3{\mathrm{H}}_6{\mathrm{O}}_3\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-121.2\ \mathrm{kJ}/\mathrm{mol} $$
(11)

Finally, trioxane and methylal form different kinds of OMEx, whereby x = 2 to 8. This is displayed as a gross reaction in Eq. (12) at 1 bar and 343 K:

$$ {\mathrm{C}}_3{\mathrm{H}}_6{\mathrm{O}}_3+{\mathrm{C}\mathrm{H}}_3\mathrm{O}{\mathrm{C}\mathrm{H}}_2\mathrm{O}{\mathrm{C}\mathrm{H}}_3\leftrightarrow {\mathrm{C}\mathrm{H}}_3\mathrm{O}{\left({\mathrm{C}\mathrm{H}}_2\mathrm{O}\right)}_4{\mathrm{C}\mathrm{H}}_3\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-9.0\ \mathrm{kJ}/\mathrm{mol} $$
(12)

This gross reaction can be divided into different reaction steps:

$$ {\mathrm{C}}_3{\mathrm{H}}_6{\mathrm{O}}_3\leftrightarrow 3\ {\mathrm{C}\mathrm{H}}_2\mathrm{O}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=56.1\ \mathrm{kJ}/\mathrm{mol} $$
(13)
$$ {\mathrm{CH}}_2\mathrm{O}+{\mathrm{CH}}_3\mathrm{O}{\mathrm{CH}}_2\mathrm{O}{\mathrm{CH}}_3\leftrightarrow {\mathrm{CH}}_3\mathrm{O}{\left({\mathrm{CH}}_2\mathrm{O}\right)}_2{\mathrm{CH}}_3\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-38.3\ \mathrm{kJ}/\mathrm{mol} $$
(14)
$$ {\mathrm{CH}}_2\mathrm{O}+{\mathrm{CH}}_3\mathrm{O}{\left({\mathrm{CH}}_2\mathrm{O}\right)}_2{\mathrm{CH}}_3\leftrightarrow {\mathrm{CH}}_3\mathrm{O}{\left({\mathrm{CH}}_2\mathrm{O}\right)}_3{\mathrm{CH}}_3\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-44.4\ \mathrm{kJ}/\mathrm{mol} $$
(15)
$$ {\mathrm{CH}}_2\mathrm{O}+{\mathrm{CH}}_3\mathrm{O}{\left({\mathrm{CH}}_2\mathrm{O}\right)}_3{\mathrm{CH}}_3\leftrightarrow {\mathrm{CH}}_3\mathrm{O}{\left({\mathrm{CH}}_2\mathrm{O}\right)}_4{\mathrm{CH}}_3\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-44.4\ \mathrm{kJ}/\mathrm{mol} $$
(16)

Table 1 shows the change in Gibbs energy and enthalpy for different steps on route B toward OME-4 as published by Burger [9]. In the meantime, the same research group prefers a synthesis via formaldehyde and methanol in aqueous solution termed route A; see Schmitz et al. [77]. The calculations for this paper were performed under idealized conditions for route B in order to get an approximation tool without using Aspen Plus® flow sheeting. Gases were approximated as ideal, even at high pressure; liquids were assumed as ideal mixtures. Thermodynamic property data were taken from [68] as a preference dataset. An initial set of information can be gained under standard conditions: all reactions on route B are exothermic. The change in Gibbs energy is strongly negative only for the partial oxidation of methanol into formaldehyde. Methanol synthesis offers a weakly positive value near to zero, indicating a conversion between 40 and 60%, as already determined more accurately by Peters [69]. Both trioxane and methylal synthesis show a weak negative change in Gibbs energy ΔGR, while ΔGR is positive for OME-4 synthesis in the liquid phase.

Table 1 Change in Gibbs energy and enthalpy for different steps on route B towards OME-4 published by Burger [9, 76]. Gases were approximated as ideal gas; liquids assumed as ideal mixtures. Thermodynamic property data were taken from Perry and Green for the ideal gas state and liquid state [68]

Changing pressure and temperature to the reaction conditions improves ΔGR with respect to the product side for nearly all species except methanol. The catalyst used demands a temperature of between 250 and 300 °C to be active, which leads to a more positive ΔGR that must be compensated by a high pressure of about 80 bar. OME-4 synthesis is even more difficult to realize, at a ΔGR of 33.6 MJ/kmol.

The assumptions of an ideal mixture in the liquid phase are strongly misleading for the thermodynamic property relations in OME synthesis. The mixtures of different intermediates such as formaldehyde and methylal form various azeotropes and miscibility gaps with water and methanol. Formaldehyde and water form methylene glycols of different chain lengths, whereas formaldehyde and methanol form hemiformals of different chain lengths.

This attempt was successfully developed by Maurer [56] and continued by Albert et al. [1]. These models were then implemented by Schemme [73] with Aspen Plus® flow sheeting. Accurate model calculations are highly important for the precise design of separation units between products, by-products, and intermediates. A quality check of the implemented models was successfully performed by comparing the modeled separation behavior with the experimental data of Burger et al. [10]. The results of the techno-economic evaluation of different process routes for OME synthesis will be published in the near future; see Schemme [73].

Nevertheless, Table 2 shows that the approximation of ΔGR and ΔHR by idealized models, i.e., an ideal gas phase and ideal liquid mixture behavior, are confirmed by more complex models, applying an equation of state for polar gases at high pressure and the Universal Quasichemical Functional Group Activity Coefficients (UNIFAC) model for a non-ideal liquid mixture. ΔGR changes from step to step in the reaction scheme (row to row) to more negative values, as can be seen in Tables 1 and 2. Considering Gibbs energy analysis, the most extensive step in OME3-5 synthesis is methanol formation with medium conversion in the range 40–60%, given a recycling loop or multi-stage synthesis. The final step in the idealized reaction scheme, the formation of OME4 according to Eq. (12), offers a positive ΔGR, indicating lower conversion. Here, a more detailed process analysis is required.

Table 2 Change in Gibbs energy and enthalpy for different steps on route B towards OME-4, published by Burger [9, 76]. Columns 5 and 6 show gases that were approximated as ideal even at high pressure; liquids were assumed as ideal mixtures (IG: ideal Gas, IM, ideal mixture). Columns 7 and 8 indicate gases that were approximated as real gases (RG) with an equation of state, i.e., polar Soave Redling Kwong, even at high pressure and liquids assumed as real mixtures with UNIFAC as GE model for excess Gibbs energy of mixture

Different pathways for the synthesis of higher alcohols are described by Schemme et al. [75]. Preferred reaction pathways toward 2-butanol and i-octanol are aldol condensation and oxo synthesis.

As was mentioned before, thermodynamic property data for the ideal gas state and pure liquid substances were calculated using formulae listed in [68] if available. Some components, such as crotonaldehyde, are missing from this dataset. Different approximation methods led to noteworthy deviations in certain cases. The enthalpy of formation and Gibbs energy of formation are calculated at − 94.3 kJ/mol and − 36.5 kJ/mol, respectively, with the method of Joback and Reid [46]. Da Silva and Bozelli published a measured value for the enthalpy of formation of about 102.1 ± 0.5 kJ/mol [79]. The National Institute of Standards and Technology (NIST) database contains experimental data of between 100.5 and 109.7 kJ/mol [14]. With the aid of the computational chemistry comparison and benchmark database of NIST, a standard ideal gas entropy of between 312.4 and 323.7 kJ/(mol K) was determined [63]. Assuming a dataset (H;S) at standard temperature and pressure in the ideal gas state of about (− 109.7 kJ/kmol; 314.2 kJ/(kmol K)) leads to a Gibbs energy formation of about − 49.2 kJ/mol—an increase of 35%, corresponding to the Joback method [46], due to the varying enthalpy of formation.

The following equations explain the reaction scheme of i-octanol by aldol condensation. The reaction pathway begins with methanol synthesis from CO2 and H2 via Eq. (12). Methanol is the educt for a subsequent synthesis of dimethyl ether (DME) at 80 bar and 523 K:

$$ 2\ {\mathrm{CH}}_3\mathrm{O}\mathrm{H}\leftrightarrow {\mathrm{CH}}_3\mathrm{O}\ {\mathrm{CH}}_3+{\mathrm{H}}_2\mathrm{O}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-24.0\ \mathrm{kJ}/\mathrm{mol} $$
(17)

Other pathways, such as a direct synthesis of DME from CO2 and H2 or parallel chemical reactions (Eqs. (12), (13)) on a bi-functional catalyst, were reported by Krause and Keskinen [50]. For the next step, syngas is required that can be produced by reverse water-gas shift reaction, see Eq. (3). Carbon monoxide and DME form methyl acetate at 140 bar and 478 K.

$$ \mathrm{CO}+{\mathrm{CH}}_3\mathrm{O}\ {\mathrm{CH}}_3\leftrightarrow {\mathrm{CH}}_3\mathrm{COO}\ {\mathrm{CH}}_3\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-117.3\ \mathrm{kJ}/\mathrm{mol} $$
(18)

Ethyl acetate itself decomposes into methanol and ethanol at 140 bar and 478 K:

$$ {\mathrm{C}\mathrm{H}}_3\mathrm{COO}\ {\mathrm{C}\mathrm{H}}_3\leftrightarrow {\mathrm{C}\mathrm{H}}_3\mathrm{OH}+{\mathrm{C}}_2{\mathrm{H}}_5\mathrm{OH}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-24.0\ \mathrm{kJ}/\mathrm{mol} $$
(19)

The direct synthesis of ethanol from CO2 and H2 is less maturate, as Schemme et al. [75] reported. The change in Gibbs energy for direct ethanol synthesis amounts to − 59.3 kJ/mol. Ethanol synthesis via DME offers a value of − 31.2 kJ/mol under real gas conditions, which indicates that this route can also be realized with sufficient conversion.

Afterwards, ethanol is dehydrogenated at 1 bar and 673 K:

$$ {\mathrm{C}}_2{\mathrm{H}}_5\mathrm{OH}\leftrightarrow {\mathrm{C}}_2{\mathrm{H}}_4\mathrm{O}+{\mathrm{H}}_2\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=68.8\ \mathrm{kJ}/\mathrm{mol} $$
(20)

Two ethanol molecules go into the aldol condensation, forming croton aldehyde and water at 70 bar and 493 K.

$$ 2\ {\mathrm{C}}_2{\mathrm{H}}_4\mathrm{O}\leftrightarrow {\mathrm{C}}_4{\mathrm{H}}_6\mathrm{O}+{\mathrm{H}}_2\mathrm{O}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-18.9\ \mathrm{kJ}/\mathrm{mol} $$
(21)

Croton aldehyde is hydrogenated to 1-butanol at 70 bar and 493 K.

$$ {\mathrm{C}}_4{\mathrm{H}}_6\mathrm{O}+2\ {\mathrm{H}}_2\leftrightarrow {\mathrm{C}}_4{\mathrm{H}}_9\mathrm{OH}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^0=-165.1\ \mathrm{kJ}/\mathrm{mol} $$
(22)

Butanol is dehydrogenated to butanal at 70 bar and 493 K.

$$ {\mathrm{C}}_4{\mathrm{H}}_9\mathrm{OH}\leftrightarrow {\mathrm{C}}_4{\mathrm{H}}_8\mathrm{O}+2\ {\mathrm{H}}_2\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^0=67.6\ \mathrm{kJ}/\mathrm{mol} $$
(23)

Two butanal molecules go into the aldol condensation, forming 2-ethylhexen-1-al (IUPAC name [62] and water at 1 bar and 323 K.

$$ 2\ {\mathrm{C}}_4{\mathrm{H}}_8\mathrm{O}\leftrightarrow {\mathrm{C}}_5{\mathrm{H}}_8\left({\mathrm{C}}_2{\mathrm{H}}_5\right)\ \mathrm{CHO}+{\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^0=-24\ \mathrm{kJ}/\mathrm{mol} $$
(24)

2-Ethylhexen-1-al will be hydrogenated to 2-ethylhexan-1-ol at 1 bar and 323 K.

$$ {\mathrm{C}}_5{\mathrm{H}}_8\left({\mathrm{C}}_2{\mathrm{H}}_5\right)\ \mathrm{C}\mathrm{HO}+2\ {\mathrm{H}}_2\leftrightarrow {\mathrm{C}}_5{\mathrm{H}}_{10}\left({\mathrm{C}}_2{\mathrm{H}}_5\right)\ \mathrm{C}{\mathrm{H}}_2\mathrm{OH}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^0=-168.8\ \mathrm{kJ}/\mathrm{mol} $$
(25)

The molecule 2-ethylhexan-1-ol is one type of various isomers of isooctanol and will, for sake of simplicity, be labeled as ethylhexanol in the following sections.

Table 3 shows the change in Gibbs energy and enthalpy for different steps toward 1-butanol and i-octanol as published by Schemme [75]. Gases were approximated as ideal, liquids assumed as ideal mixtures. Thermodynamic property data were taken from Perry and Green for the ideal gas state and liquid state, except for crotonaldehyde, 2-ethyl hexenal, and 2-ethyl hexanol. (H, S, G)-data for crotonaldehyde were based on values given by NIST [63, 64], (H, S, G)-data for 2-ethyl hexenal, and 2-ethyl hexanol were determined using the method of Joback and Reid [46]. Calculated data for 1-octanol and 2-ethyl hexanol offers minor deviations compared to Joback, NIST, and the Korea Thermophysical Properties Data Bank (KDB) data base [14, 46, 64].

Table 3 Change in Gibbs energy and enthalpy for different steps toward 1-butanol and i-octanol as published by Schemme [75]

Table 3 indicates that most processes in the considered octanol synthesis process chain are exothermic, except for the dehydrogenation of ethanol and butanol to ethanal and butanal and for the reverse water gas shift reaction. As can be seen from Eqs. (20) and (23), as well as Table 3, dehydrogenation at standard pressure and temperature is characterized by a positive change in enthalpy and in Gibbs energy. Endothermic reactions should be performed at elevated temperatures. An increase in moles during a chemical reaction is better realized at low pressure. Following the principle of Le Chatelier, the chemical reaction of dehydrogenation is considered at 1 bar and 673 K. Under these assumptions, the changes in Gibbs energy towards the products ethanal and butanal amount to − 18.1 kJ/mol and − 13.7 kJ/ mol, respectively, for the ideal gas state.

The reverse water gas shift reaction is indicated by a positive ΔGR of about 28.6 kJ/ mol, which leads to a conversion of much less than 5% under standard conditions; see Fig. 4.

At 1073 K change in Gibbs energy, ΔGR amounts to 0.8 kJ/kmol, leading to a conversion higher than 80%. According to Eq. (19), high pressure enhances the formation of ethanol and methanol from ethylacetate, which is indicated by an improvement for ΔGR from − 4.7 kJ/mol at standard conditions to − 107 kJ/mol at 140 bar and 478  K. The most difficult step seems to be the formation of croton aldehyde via reaction (21). The formation of ethylhexenal and ethylhexanol are both improved at slightly elevated temperatures of 323 K. ΔGR amounts to − 30.1 kJ/kmol under 70 bar and 493 K.

A heat integration concept can be derived if all duties and heat sources are defined. A more detailed analysis of the complete process chain will be discussed in the next section. The number of required process units will also be graphically indicated.

Process analysis

The aim of this section is to consider the question of which fuels or intermediates are suitable for production from biogas and can be temporarily stored on a farm. With regard to the production of a diesel substitute, the selected pathways toward higher alcohols or ethers should be analyzed. The principle steps in the OME3-5 synthesis on route B, originally proposed by Burger [9], are implemented in Eqs. (8)–(16) and summarized in Table 1 and Table 2. The research group of the Technical University of Munich [10, 11, 40, 77] recently preferred route A, whereby the synthesis of intermediates trioxane and methylal can be avoided. The disadvantage of this route is a wet OME3-5 synthesis process, in combination with a complex separation system. For the synthesis of higher alcohols on the route of aldol condensation reported recently by Schemme et al. [75], chemical reactions, Gibbs energy, and the heat of the reaction data are given in Eqs. (17)–(25) and summarized in Table 3.

In order to elucidate the effort for different fuel synthesis systems, a new scheme was developed. Process units such as heat exchangers, mixers, distillation columns, pumps, compressors, and chemical reactors were sketched on a checkered field in individual positions. On the y-axis, each center line between two rows represents another pure substance or a mixture of educts or products. Pure substances are, for example, water/steam and trioxane, while a mixture is in the liquid state methanol-water or a gaseous mixture H2 and CO2. On the x-axis, each new process unit demanded induces a step to the right. Symbols were always positioned on the intercept points of the grid.

Figure 8 starts in the lower left-hand corner with the compression and mixing of carbon dioxide and hydrogen on lines 1–3. After pre-heating the gaseous educt mixture, a methanol-water mixture was produced over a catalyst in a chemical synthesis reactor. Methanol and water are separated via distillation and fed into two provision/removal pipelines. The required recycling loop with the separation of the non-converted gases from the liquid product phase is only implied by a recycling sign. In the case that a distillation demands two columns, only one step is performed to the right; four columns, i.e., two pairs at different pressures to overcome azeotropes, are indicated by moving two lines to the right.

Fig. 8
figure 8

Principle flow sheet of multi-stage synthesis of OME3-5 via methylal and trioxane, route B; see also Burger [9]. For example: line 2 with molecules H2, CO2 as educts in Eq. (8); line 5 with molecules CH3OH, H2O as products in in Eq. (8). Next example: line 8 with molecules CH3OH, O2 as educts in Eq. (9); line 9 with molecules CH2O, H2O as products in in Eq. (9)

OME3-5 via intermediates methylal and trioxane occupy 17 horizontal and 22 vertical lines in such a sketch. Figure 9 shows the principle flow sheet of the multi-stage synthesis of 2-ethylhexanol via aldol condensation from butanol reported by Schemme et al. [75]. This synthesis route requires 22 horizontal and 19 vertical lines. In turn, ethylhexanol synthesis demands more chemical reaction steps compared to OME3-5 synthesis, resulting in the higher number of horizontal lines. However, the process of OME3-5 synthesis demands more thermal separation units related to alcohol synthesis, resulting in the higher number of vertical lines. The complexity of these separation steps is caused by the non-ideal thermodynamic properties of the different reaction steps in ether synthesis. Details on thermodynamic modeling can be found in Schemme [73].

Fig. 9
figure 9

Principle flow sheet of multi-stage synthesis of 2-ethylhexanol via aldol condensation from butanol as reported by Schemme et al. [75]. For example: line 14 with molecule C2H5OH as educt in Eq. (20); line 15 with molecules H2, C2H4O, as products in in Eq. (20)

Considering an optional cut between the decentralized synthesis of an intermediate at the farm site and centralized fuel synthesis, methanol is definitely the preferred species in the case of OME3-5 synthesis. This is caused by the junction of parallel synthesis pathways for trioxane and methylal, forming the desired product of OMEx in a final step. Therefore, OME3-5 was not considered for process optimization at the farm site. In the case of alcohol synthesis, methanol, ethanol, and butanol are applicable intermediates. DME can only be chosen with a modification of the synthesis pathway. Nevertheless, both process chains toward OME3-5 and 2-ethylhexanol require a large amount of intermediate chemical reaction steps and, for some cases, a fairly complex and extensive separation processes. In the next section, optimization toward process simplification will be discussed.

Process design for optimized synthesis processes

In this section, a series of purely stoichiometric conceivable chemical reactions, starting from biogas, are presented and an estimate of their corresponding chemical and thermodynamic feasibility is given. Generally, this exercise should enable a broader perspective on the possible pathways to be gained. The biogas components of methane and carbon dioxide may react directly to acetic acid, as conveyed in Eq. (26):

$$ {\mathrm{CH}}_4+{\mathrm{CO}}_2\leftrightarrow {\mathrm{H}}_3\mathrm{C}-\mathrm{COOH}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=35.2\ \mathrm{kJ}/\mathrm{mol} $$
(26)

The formed acetic acid could be hydrogenated in a subsequent reaction to form ethanol.

$$ {\mathrm{H}}_3\mathrm{C}-\mathrm{COOH}+2{\mathrm{H}}_2\leftrightarrow {\mathrm{H}}_5{\mathrm{C}}_2\mathrm{O}\mathrm{H}+{\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-44.0\ \mathrm{kJ}/\mathrm{mol} $$
(27)

Figure 10 shows the principle flow sheet for acetic acid synthesis from methane and carbon dioxide in combination with an energy analysis in G,H-diagram under standard ideal gas state conditions (STP).

Fig. 10
figure 10

Principle flow sheet for acetic acid synthesis from methane and carbon dioxide in combination with an energy analysis in G,H-diagram under standard ideal gas state conditions (STP). Symbols see legend in Figs. 8 and 9

Thermodynamic calculations indicate a difference in Gibbs energy for a completed reaction to acetic acid of about 73.7 kJ/mol ethanol. Methane is a stable molecule, due to its tetrahedral structure. As was already shown in Fig. 5, for the dry reforming of methane, high temperatures (and a catalyst) are required to activate the C-H bond in methane for a further chemical reaction.

As a second “option,” carbon monoxide can be formed via reverse water gas shift reaction, as in Eq. (3). Subsequently, methane and carbon monoxide form ethanal (see Eq. (28)), which can be hydrogenated into ethanol.

$$ {\mathrm{CH}}_4+\mathrm{CO}\leftrightarrow {\mathrm{H}}_3\mathrm{C}-\mathrm{HC}=\mathrm{O}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=18.85\ \mathrm{kJ}/\mathrm{mol} $$
(28)

The difference in Gibbs energy for a completed reaction to ethanal amounts to 58 kJ/mol ethanol, as can be seen in Fig. 11. Due to the implementation of a reverse water gas shift reactor, the process scheme includes more elements related to Fig. 10.

Fig. 11
figure 11

Principle flow sheet for ethanol synthesis from methane and carbon monoxide, in combination with an energy analysis in G,H-diagram under standard ideal gas state conditions (STP). Symbols see legend in Figs. 8 and 9

The formation of methyl acetate from dimethyl ether and carbon monoxide is an important reaction step toward ethanol according to Eq. (18). Equation (29) offers a chemical reaction between methanol and carbon monoxide, forming acetic acid. The process was originally developed by BASF in 1960. A corresponding plant was built by Monsanto in Texas that applied an improved catalyst, as reported by Roth [72].

$$ {\mathrm{CH}}_3\mathrm{OH}+\mathrm{CO}\leftrightarrow {\mathrm{H}}_3\mathrm{C}-\mathrm{COOH}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-121.3\ \mathrm{kJ}/\mathrm{mol} $$
(29)

Figure 12 shows the principle flow sheet for acetic acid synthesis from methanol and carbon monoxide, in combination with an energy analysis in G,H-diagram under standard ideal gas state conditions (STP). In comparison to Fig. 9, the number of pure components and mixtures on the y-axis decreases from 14 to 12, while the number of elements decreases from 20 to 17, indicating a slight improvement. A noteworthy disadvantage is the formation of a water-ethanol solution. Its separation requires a second distillation column due the azeotrope in the system. The proposed pathway via DME (see Fig. 9) results in the distillation of ethanol and methanol, which forms no azeotropes.

Fig. 12
figure 12

Principle flow sheet for acetic acid synthesis from methanol and carbon monoxide, in combination with an energy analysis in G,H-diagram under standard ideal gas state conditions (STP). Symbols see legend in Figs. 8 and 9

Figure 12 shows that both reaction steps achieve negative changes in Gibbs energy at standard conditions in the ideal gas state. From a thermodynamic point of view, this approach is very rough because the Monsanto process is performed as a homogeneously catalyzed reaction in the liquid phase at 30–60 bar and 423–473 K applying a Rh-complex catalyst; see [72].

The methanol-to-olefin process offers a further option for producing alcohols. For an olefin CnH2n from methanol, the following synthesis reaction occurs, resulting in various olefins:

$$ \mathrm{n}\ {\mathrm{C}\mathrm{H}}_3\mathrm{OH}\leftrightarrow {\mathrm{C}}_n{\mathrm{H}}_{2n}+\mathrm{n}\ {\mathrm{H}}_2\mathrm{O}\kern0.4em {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}>0\ \mathrm{kJ}/\mathrm{mol} $$
(30)

Kvisle et al. reported on different MTG/methanol to olefins (MTO) technologies. Using different catalysts, product spectra such as 5% C1–C3 paraffins, 50% ethene, 35% propene, and 10% butane and higher hydrocarbons, or 5% C1–C3 paraffins, 8% ethane, 45% propene, and 45% butane and higher hydrocarbons are achievable [52]. A commercial plant from universal oil products (UOP) gains a yield of ~ 50% mass from 3000 t/a with a yearly production of 500 t ethene (17%), 500 t propene (17%), and 167 t butane (5.6%).

Oelfins can also be formed from DME by the following:

$$ \raisebox{1ex}{$\mathrm{n}$}\!\left/ \!\raisebox{-1ex}{$2$}\right.\ {\mathrm{C}\mathrm{H}}_3\mathrm{O}{\mathrm{C}\mathrm{H}}_3\leftrightarrow {\mathrm{C}}_n{\mathrm{H}}_{2n}+\raisebox{1ex}{$\mathrm{n}$}\!\left/ \!\raisebox{-1ex}{$2$}\right.\ {\mathrm{H}}_2\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}>0\ \mathrm{kJ}/\mathrm{mol} $$
(31)

Table 4 shows the change in Gibbs energy and enthalpy for different steps from methanol and DME to olefins. The values for the change in Gibbs energy during the reaction and heat of the reaction differ only slightly between the different models.

Table 4 Change in Gibbs energy and enthalpy for different steps from methanol and DME to olefins. The gases in rows 4-7 were approximated as ideal; the liquids assumed as ideal mixtures. Thermodynamic property data were taken from [68] for ideal gas and liquid states. The real gases in rows 8 and 9 were calculated by Aspen Plus® with a modified EOS SRK for polar components [81]

In a subsequent step, alcohols can be produced from the olefins ethene, propene, and butane; see [23]. Butanol can also be formed from butene via hydration:

$$ {\mathrm{H}}_3\mathrm{C}-\mathrm{C}{\mathrm{H}}_2-\mathrm{C}\mathrm{H}=\mathrm{C}{\mathrm{H}}_2+{\mathrm{H}}_2\mathrm{O}\leftrightarrow {\mathrm{H}}_9{\mathrm{C}}_4\mathrm{OH}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-32.2\ \mathrm{kJ}/\mathrm{mol} $$
(32)

As stated by Latscha et al., water can only be added in the presence of an acid, as water itself is not electrophilic enough [53]. It is important to ensure that an acid is used whose anion is as nucleophobic as possible so that it does not compete with water; otherwise, product mixtures are formed. Sulfuric acid is often used for this purpose. Nevertheless, in the case of longer-chain alkenes, product mixtures may result, as typical carbenium ion side reactions can occur at the carbenium ion stage.

For the product propene, the oxo synthesis with syngas can be performed as follows:

$$ {\mathrm{H}}_3\mathrm{C}-\mathrm{CH}=\mathrm{C}{\mathrm{H}}_2+\mathrm{CO}\leftrightarrow {\mathrm{H}}_3\mathrm{C}-\mathrm{CH}=\mathrm{C}\mathrm{H}-\mathrm{HC}=\mathrm{O}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-18.9\ \mathrm{kJ}/\mathrm{mol} $$
(33)

The formed croton aldehyde is subsequently hydrogenated to butanol according to:

$$ {\mathrm{H}}_3\mathrm{C}-\mathrm{CH}=\mathrm{CH}-\mathrm{HC}=\mathrm{O}+2\ {\mathrm{H}}_2\leftrightarrow {\mathrm{H}}_9{\mathrm{C}}_4\mathrm{OH}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-165.1\ \mathrm{kJ}/\mathrm{mol} $$
(34)

The last main product of the MTO process ethene can react with water to ethanol by hydration.

$$ {\mathrm{H}}_2\mathrm{C}=\mathrm{C}{\mathrm{H}}_2+{\mathrm{H}}_2\mathrm{O}\leftrightarrow {\mathrm{H}}_5{\mathrm{C}}_2\mathrm{O}\mathrm{H}\ {\Delta }_{\mathrm{R}}{\mathrm{H}}^{\mathrm{o}}=-32.2\ \mathrm{kJ}/\mathrm{mol} $$
(35)

Fougret and Hölderich applied metal phosphates (containing aluminum, zircon and cerium) at 300 °C and 50 bar, which were then impregnated with phosphoric acid [27]. Selectivity reaches 99.9% with small amounts of acetaldehyde as a by-product. Via aldol condensation butanol can be gained; see Eqs. (20)–(22). Figure 13 shows a principle flow sheet for butanol synthesis from methanol via the oxo synthesis of propene and carbon monoxide, in combination with an energy analysis in a G,H-diagram under standard ideal gas state conditions (STP). In comparison to Fig. 9, the number of pure components and mixtures on the y-axis remains 14, while the number of elements decreases slightly, from 20 to 19. Both cases of oxo synthesis form either DME or, from methanol, reach the same complexity. An advantage of the process is the good separation of butane and water indicated by the large difference in Gibbs energy for water and butane. According to the change in Gibbs energy, it seems that CO feeding is more difficult to realize than the hydrogenation of crotonaldehyde. Figure 14 shows a principle flow sheet for butanol synthesis from methanol via butene hydration, in combination with an energy analysis in the G,H-diagram under standard ideal gas state conditions (STP). In comparison to Fig. 9, the number of pure components and mixtures on the y-axis decrease from 14 to 9, while the number of elements decreases drastically, from 20 to 12. The change in Gibbs energy for butane hydration amounts to 8 kJ/mol butanol, indicating an equilibrium conversion of about 50% under standard conditions. If the reaction proceeds in the liquid phase, activity coefficients calculated by GE models such as NRTL or UNIFAC should be used [28, 80]. A deeper technological assessment must be worked out to determine which pathway achieves the highest yield on butanol with minimal complexity.

Fig. 13
figure 13

Principle flow sheet for butanol synthesis from methanol via oxo synthesis of propene and carbon monoxide, in combination with an energy analysis in a G,H-diagram under standard ideal gas state conditions (STP). Symbols see legend in Figs. 8 and 9

Fig. 14
figure 14

Principle flow sheet for butanol synthesis from methanol via butene hydration, in combination with an energy analysis in a G,H-diagram under standard ideal gas state conditions (STP). Symbols see legend in Figs. 8 and 9

The MTO route offers a narrow spectrum of C2–C4 olefins. With catalyst selection, a focus on propene/butene or ethene/propene mixtures can be set. A hydration step at a farm site would lead to a mixture of various alcohols such as ethanol, 1-propanol, 2-propanol, 1-butanol, and 2-butanol. It must be determined if such a mixture can be used directly in potential applications such as internal combustion engines. Otherwise, downstream processing must be implemented. A target production of pure butanol can be achieved by a combination of different chemical reactions. Firstly, a distillation into different fractions of C2, C3, and C4 alcohols must be performed. The extracted propanol must then be dehydrogenated into propene for the next reaction step. Afterwards, butanol can be gained by means of the aldol condensation of ethanol and by an oxo synthesis of propene. The complexity of this reaction scheme hints at a central production unit.

Considering the production of a liquid at a farm site from H2 and CO2 can be realized at best by methanol synthesis. Subsequently, MTO synthesis is a viable option, in combination with hydration, to achieve a mixture of short-chain alcohols, ranging from ethanol to butanal, and possibly to pentanol.

Socio-economic aspects

The socio-economic aspects that will be discussed in the next three sections are handling and storage at farm sites, economic factors, and an outlook on environmental evaluation. A further selection of preferred production chains can be found at the end of this paper.

Handling and storage at farm sites

Social and economic aspects play an important role in the decision of whether to produce locally at farm sites or to undertake production at a central site. This section evaluates fuels with regard to their characteristics that can influence the production decision.

As mentioned above, applicable intermediates concluded from this study are alcohols and DME. The alcohols investigated are methanol, ethanol, butanol, and octanol. These substances are liquids with characteristic odors that are flammable and have a certain risk of explosion at high temperatures, or when mixed with air. DME, for instance, is an extremely flammable gas. Thus, when handling such substances, certain safety protocols must be observed. In the following, these substances are compared according to their health and safety considerations during handling and their characteristics for storage and transport. Tables 5, 6, and 7 contain important information and help with the comparison. The evaluative remarks are an initial attempt to evaluate the risk of farm-site production and provide recommendations. In the end, the risk estimation and production decision should be made by an authorized assessor.

Table 5 Substance characteristics relevant for health from the [43, 44]
Table 6 Substance characteristics relevant for storage, transport, and safety requirements; if not specified otherwise, data was taken from the [43]
Table 7 Main results from process analysis for methanol, ethanol, 1-butanol, i-octanol, and DME taken from Schemme et al. [74]. Base case: 4.6 €/kg H2, 70 €/t CO2, interst rate: 8%, process steam: 32 €/t, cooling water: 0.1 €/t, operating electricity: 9.76 €ct/kWh

Health risks

All substances evaluated in this study pose acute and chronic health risks. People can be exposed to them by inhalation, ingestion, and through the skin. In particular, inhalation and direct skin contact may be relevant for workers on the farm, as they could be exposed to the vapor or liquid. Although the substances do not have carcinogenic potential, they can cause irritation to the eyes, skin, and respiratory system; see [43]. Furthermore, DME can create cold fog when leaking, which may cause frostbite. Accumulation of the gas in lowered spaces may in turn cause a shortage of oxygen, which poses the risk of suffocation; see [44].

One serious health risk is the effect of all of the substances on the central nervous system, whereby inhalation can cause confusion, fatigue, headache, and lack of concentration and can even cause unconsciousness in the case of methanol, ethanol, and DME. Methanol has especially serious potential consequences on health. Direct and/or delayed effects include blindness [44] and the potential of death when being exposed to a high concentration of the vapors for several hours because of unconsciousness (> 5000 ppm) [42]. The “Institut für Arbeitsschutz der Deutschen Gesetzlichen Unfallversicherung” (IFA) reports blurred vision and/or headaches as the most common disorders after a longer period of exposure in the workplace of approximately 1000 ppm on average [43]. Headaches were also reported for shorter periods. A notable aspect may be that methanol in the air is difficult to smell at concentrations below 2000 ppm (1500 mg/m3) [7]. As the critical workplace value is only 270 mg/m3, it may be difficult to recognize exceedance of this. In general, the critical values allowed in the work place decrease the longer the carbon chain in the alcohol molecule is, resulting in lower amounts of, e.g., butanol and octanol being more irritating compared to methanol and ethanol. Of the alcohols, ethanol is the least toxic (for critical workplace values, compare Table 4). In general, risk estimation is difficult, as critical values and effects are not known to the full extent for all substances [68]. None of the chosen substances can be excluded though and a safety analysis must be performed at each installation site. An official approving authority should then certify the safety measures taken. With regard to the data shown in Table 5, ethanol and butanol are the most suitable.

Handling and storage

Apart from the health risk, another aspect that is relevant for storage on farms is the risk of explosion. Under the UN hazard classification, the alcohols are classified under category 3 as flammable liquids. DME is classified under category 2.1 as a flammable gas (see Table 46). In the air, as vapor or combined with incompatible substances, methanol, ethanol, and DME easily form explosive mixtures. Butanol and octanol are only explosive at 29 °C and 81 °C. Their volatility is medium to low, respectively, while methanol and ethanol are highly volatile. DME is heavier than air. It can form a cold fog that travels along the ground and may ignite from a distance. Indeed, a risk of explosion exists for all of the substances, even though it is very lower for octanol [44].

All substances carry certain risks and require safety regulations, such as the control of critical emission values through the installation of gas sensors and the use of closed, solid gadgets and containers to prevent hazards. Thus, handling and coping with spillages requires some expertise. For the prevention of safety hazards, a closed system is suggested with explosion-proof electrical equipment and ventilation [43].

Due to their high flammability, the handling and storage of methanol, ethanol, butanol, and DME must follow official explosion protection directions (“Explosionsschutz-Richtlinie”). In order to avoid the risk of fire, one should not use compressed air for handling, filling, or discharging (see [43]. Furthermore, the handling of spillages should be carried out in protective clothing and, for all substances but octanol, with the help of a filter respirator for organic vapors and gases. For the storage of butanol and octanol, it is important to consider that they have an effect on materials such as rubber, some plastics, and coatings. Methanol and DME must be stored in a cool place, while DME must also be kept close to the ground [44]. DME tanks should not be exposed to sunlight and the temperature of the substance should be kept below 52 °C [57]. Methanol is safely stored at a pressure of 2–7 bar depending on the ambient temperature [54]. The requirements of a fireproof and well-ventilated place, away from incompatible substances, apply to all intermediates [44]. With regard to the data shown in Table 6, butanol and octanol are the most suitable in terms of handling and storage.

Transport

Handling regulations are also important for transport. It is necessary to consider this aspect when producing intermediates at the farm level. Transport is especially relevant for methanol, ethanol, and, to a certain extent, DME. Methanol is classified in packing group II (medium hazard) and ethanol in between group II/III (medium/low hazard). Verhelst et al. state that methanol, for instance, is easy to handle as it is liquid at room temperature [92]. It only becomes gaseous above its boiling point at 65 °C. The boiling point for other alcohols is even higher, which means that they are likely to remain in liquid form. DME, which is unassigned to a packing group, must be transported in liquid form in low pressure tanks [43]. Pressure tanks must be secured against tipping and handled using a hand truck [57]. Moreover, the transport of DME requires a permit by a local authority (see [43]). In comparison, this makes the transport of DME more expensive and complex than that of the alcohols.

Comparison with other fuels

If the above-mentioned intermediates are compared to other fuels, such as diesel and gasoline, for instance, methanol and ethanol are similar or even less toxic, lethal doses that are generally higher. Furthermore, none of the substances cause cancer [7]. In particular, methanol has been investigated as an alternative fuel in the literature with concern for its safety aspects. In terms of the risk of fire, methanol takes three times longer to ignite compared to gasoline. It also burns with less smoke and a lower temperature, and is easy to extinguish. Therefore, a fire is less likely to occur and if it does, is less damaging. Even the health hazards are considered to be manageable for laymen [13]. Verhelst et al. came to the conclusion that, on the one hand, the storage of methanol is less safe than that of diesel due to its lower flash point [92]. On the other hand, its storage is considered safer than gasoline. Additionally, the vast expansion of the methanol infrastructure in China and the already successful trial case of using fuel in racing cars in California suggests that methanol can be handled safely [7].

Economic aspects

Costs are important for an investment decision on a synthesis plant, especially if the investment must come from an individual such as a farmer. The system must be able to produce fuels at a competitive price. In general, if a synthesis plant is built, costs augment with the size of it; the more process steps are included, the higher the equipment costs. Schemme [73] analyzed power-to-fuel production facilities for much larger capacities between 30 and 300 MWth than for a typically farm size of about 1 MWth. A summary of his results is published in Schemme et al. [74]. Important results for methanol, ethanol, 1-butanol, 1-octanol, and DME are given in Table 7. The comparison shows for example costs between 1.85 €/lDE (DME) up to 2.85 €/lDE (i-octanol). These numbers correspond very good to the results of Brynolf et al. [8] with 1.60–2.09 €/lDE. When looking at responsible cost factors, the highest costs in power-to-fuel production systems occur for the supply of hydrogen. The share of total costs that can be assigned to the H2 supply is between 70 and 80%. Expenses for CO2 were assumed to be at 70 €/t CO2 for these studies. For economic analyses of power-to-fuel concepts, the system efficiency is also an important criteria. Methanol and DME are the best choice in regard to the data in Table 7. If the cost of power production decreases, while the efficiency and carbon conversion increase, the production costs can be minimized [2].

Following the data from FNR in Germany [91], yields between 12 and 17 m3 bio-methane/m3 liquid manure can be achieved. In regard to the majority of cattle in Germany, our group assumes 15.6 m3 bio-methane/m3 liquid manure. Actual prices to remove liquid manure of up to 30 €/m3 offer a bonus of nearly 1 €/m3 biogas, leading to a bonus of about 450 €/t CO2 if 50% of carbon were assigned to CO2.

It must be stated that the specific cost for a small-scale synthesis plant will increase related to the data of Schemme et al. [74] presented partly in Table 7. The average size of biogas plants in Germany at present corresponds to 500 kWe electrical output of a combined heat and power unit (CHP). In a series of publications, the impact of biogas plant size on the overall economic performance has been investigated by the Department of Mechanical Engineering at the University of Alberta [34, 51, 78]. Searcy et al. describe the cost optimal plant size to be a trade-off between the declining capital and operational expenditures on the one hand and increasing costs for feedstock transport on the other hand, as the plant scales increase [78]. In comparison, this approach favors plant sizes of around 200 MWe and more, which is the size at which specific capital expenditure reduction stagnates [78]. The specific cost optimal size is then dependent on the geographical distribution of different types of feedstock [78]. While these considerations are of importance for future operators of biogas plants, the evaluation of optimal plant size will not be subject of the succeeding analyses, but rather the current conditions are taken into account. Finally, this size corresponds well with the process calculation of Schemme et al. [74].

For a small unit with 500 kWe, it is more important to choose the simplest molecule for synthesis and for transport. From this perspective, methanol is the first choice. Finally, a detailed techno-economic analysis for this application is lacking and will be performed as a next step.

Environmental evaluation

The intermediates evaluated in this study have environmental impacts when they are released into the environment. These characteristics should be considered for handling and storage, aside from the above-mentioned health and safety issues. Yet, the intermediates also affect the environment during their production phase. Both aspects should therefore be taken into account when evaluating farm-site production. In this section, only environmental aspects of fuel synthesis, storage, and transport were discussed. A broader approach can consider aspects of waste water cleaning from fermentation and synthesis. Firstly, it is assumed that such a cleaning already exists between fermentation and the gas engine. Additionally, the digestate will be processed to avoid negative impacts on environment. Both items are under research and form the content of a subsequent paper.

The environmental substance characteristics are summarized in Table 6. Methanol is completely soluble in water, but causes water pollution. Therefore, it is classified in WGK 2Footnote 1; see the German Environment Agency [90]. Ethanol, butanol, and DME are also soluble in water, although their water pollution hazard is lower (WGK 1). Octanol shows a very poor solubility in water (see [43]. Yet, its release into the environment should be avoided, as it especially harms aquatic life (see [44]. The alcohols investigated are readily biodegradable, whereas DME’s biodegradation is fairly slow, as reported by [49]. With regard to the water hazard class shown in Table 8, ethanol to octanol is better to use than methanol.

Table 8 Environmental substance characteristics

Figure 15 shows the process chain, including all production steps, from the raw materials to the fuel that can cause environmental impacts. The figure includes the following impact factors: the production and pretreatment of biomass for the fermentation process (which is negligible for liquid manure), the production of hydrogen and storage, the gas separation process, and the potential fabrication and operation of the plant sites. The production steps require energy, e.g., the gas separation process and the production of hydrogen by the electrolyzer. The fabrication of plant sites may be negligible for CO2 production. Biogas upgrading is already carried out at several biogas plants [24]. Moreover, there is already a large existing infrastructure of biogas fermentation plants in Germany (9331 plants, as of 2017), as reported by Fachverband Biogas [25]. This is supported by Mezzullo et al. who note that emissions from plant construction matter just once in the lifetime of the plant, whereas emissions due to plant utilization are reoccurring [58].

Fig. 15
figure 15

Production chain with considerable steps that can cause an environmental impact for local fuel production

An environmental analysis usually gives insight into airborne emissions. For a holistic environmental assessment, the effects on soil and water should also be taken into account. During the production chain, co-products occur, such as digestate from the fermentation that can be reused as fertilizer. The biomass input from the fermentation process absorbs carbon/CO2 while growing and therefore is a carbon sink [58]. As mentioned when evaluating biomass as an energy carrier, one should consider not only its CO2 balance but also other environmental aspects, such as the protection of soil, water, and the countryside [55]. In order to consider the relevant environmental considerations in detail, the process technology must be analyzed and a life cycle assessment (LCA) should be performed to give deeper insights into farm-site production.

A first LCA modeling of a power-to-fuel methanol production process according to Fig. 15 showed interesting results, see Eggemann et al. [21]. The analysis considered exclusively residues, namely liquid manure and residues from feed processing, as feedstock and did not account for capital goods. Results showed that credit from co-products like energy and fertilizer made an important contribution in the system’s emission savings. Negative emissions, i.e., emission savings of − 3.57 kg CO2 eq. for the production of 1 kg of methanol, were achieved. In comparison, conventional methanol production had emissions of 0.74 kg CO2 equivalent. The innovative system also performed better in most of the other impact categories that were investigated and showed emission savings in almost all of them (for more details see Table 9). Only in the case of SO2 emissions, the system was more polluting. A more detailed paper about the analysis will be published in future.

Table 9 LCA modeling results; climate change (GHG), acidification potential (terrestrial) (AP), fossil depletion (FD), photochemical ozone formation (POF), human toxicity (HT), stratospheric ozone depletion (ODP), eutrophication potential (EP)

Evaluative remarks

Safety aspects can be decisive as to which intermediates and which fuel can be produced and stored. Alongside production, storage and transport issues play an important role. With regard to mass transport, liquids offer a higher power density in relation to gases. Liquefied gases such as liquid petroleum gas (LPG), DME, liquid natural gas (LNG, and liquid hydrogen (LH2) bear the effort of the implementation of a refrigeration plant, which seems to be too costly and complex for a small farm site.

Even though methanol can cause health issues, there has been sufficient production and usage of methanol as an alternative fuel to provide handling guidelines. In fact, methanol is one of the most produced chemicals in the world (60 million tonnes in 2012). It is used in a wide range of processes in the chemical industry, as well as for bulk chemicals such as formaldehyde and formic acid [33]. Furthermore, several studies have come to the conclusion that the handling risk is manageable [7, 13, 92]. Compared to diesel and gasoline, the health hazards for methanol and ethanol are similar or lower. Environmental hazards exist for all intermediates though. In summary, alcohols with a longer carbon chain in the alcohol molecule bear less risk of explosion. Transport hazards for all of them are medium to low. The transport of DME, however, requires more effort. From a convenience point of view, it may be easier to transport farm-site methanol to large production sites and centrally produce DME.

As there are other emissions that occur on a farm, farm-site production activities should take that into account. A fuel production site requires safety regulations and a storage concept. It is also important that the fuel production system is closed and at a safe distance from high temperatures or explosives. As long as safety regulations are met and the farm can guarantee safe storage and transport, farm-site production for all intermediates can be considered. However, it depends on the right equipment and acceptance by farm owners. In the end, a safety concept must be permitted by the designated authorities.

Conclusions

Among other possibilities, the production of liquid energy carriers from carbon dioxide and hydrogen can contribute to the sustainability of future energy systems. On one side, the source of hydrogen must be renewable, e.g., produced via water electrolysis using wind or solar electricity. On the other side, the production routes shall not be considered as a possibility to justify the continued operation of fossil-based carbon dioxide emitters, such as coal power plants. In this respect, the carbon dioxide content of the biogas produced in farm sites offers a biogenic carbon dioxide source complementing the renewable nature of the synthetic liquid fuels to be produced.

In order to consider all techno- and socio-economic effects of the farm-site production of synthetic fuels, a deep analysis was performed. The proposed concept foresees the local and distributed small-scale production of a liquid intermediate fuel with elevated power density. This liquid fuel or fuel mixture should be transported to a central site where it is upgraded to a certified fuel.

Firstly, a diesel-like fuel was preferred, leading to substances such as 1-octanol or an OME3-5 mixture. The thermodynamic analysis clearly showed that a syngas pre-processing to convert CO2 into CO would be better performed by a water-gas shift reactor than by dry reforming. Further on, direct synthesis is most often not possible. This is the reason why synthesis of OME3-5 is so complex. Subsequently, process analyses identified the most common route for OME3-5 as being less suitable for implementation on farm sites due to its huge number of intermediates and complex separation tasks.

Considering an optional cut between the decentralized synthesis of an intermediate at the farm site and centralized fuel synthesis, methanol is definitely the preferred species in the case of OME3-5 synthesis. This is caused by the junction of parallel synthesis pathways for trioxane and methylal forming the desired product OMEx in a final step. Therefore, OME3-5 was considered for process optimization at a central site only. In the case of alcohol synthesis, methanol, ethanol, and butanol are applicable intermediates. DME can only be chosen with a modification of the synthesis pathway. Nevertheless, both process chains require a large amount of intermediate chemical reaction steps and, for some cases, fairly complex and extensive separation processes.

Process optimization was based on a combination of a Gibbs energy analysis with a visual method identifying the number of chemical reaction steps and the effort for component separation by counting the required unit operations. Finally, a route via (a) methanol synthesis from hydrogen and carbon dioxide with water separation at the agricultural site and subsequent steps; (b) methanol-to-olefins; (c) hydration of olefins to alcohols; (d) distillation; and (e) down-stream processing for the various alcohols to fuel products at a centralized site seems to be very attractive. A viable option is the realization of steps (b) to (c) at farm sites if the complexity of the latter process units can be reduced.

Handling and safety aspects play an important role in deciding on an intermediate fuel that is suitable for farm-site production. Energy carriers that are liquid at standard conditions are most suitable due to their higher energy densities in relation to gases. Liquefied gases such as LPG, DME, LNG, and LH2 bear the effort of the implementation of a refrigeration plant and/or pressurized tanks that seems to be too costly and complex for a small farm site. Even though methanol can cause health issues, there has been sufficient experience in the production and usage of it as an alternative fuel to provide handling guidelines. Compared to diesel and gasoline, health hazards for methanol and ethanol are similar or lower. Environmental hazards also exist for all intermediates. In summary, alcohols with a longer carbon chain in the molecule bear less risk of explosion. Transport hazards for all of them are medium to low.

The fact that other emissions occur on a farm should also be taken into account when considering farm-site production. A fuel production site requires safety regulations and a storage concept. It is also important that the fuel production system is closed and at a safe distance from high temperature or explosives. As long as safety regulations are met and the farm can guarantee safe storage and transport, farm-site production for all intermediates can be considered. However, it depends on the right equipment and acceptance by farm owners. In the end, a safety concept must be permitted by the designated authorities. Additionally, an extensive risk assessment would be a valuable contribution to the scientific literature.