Abstract
Energy consumption is an important point which is crucial for green communications in 6G era, especially for those networks with limited life span or affected by dangerous environments where batteries are inconvenient to be changed. Therefore, energy harvesting (EH) has become a very attractive research field in recent years. In this paper, a new type of twoway EH relay beamforming system with two transceivers and many singleantenna relays is designed. All the transmit power of relay nodes is not restricted by the total quota or the personal quota and can be obtained entirely by energy harvesting. We use power splitting (PS) method for EH. We first establish a twoway system model for the amplifyandforward and decodeandforward relaying and then analyze the sum rate, and the gradient descent algorithm is used to solve the nonlinear joint PS factor optimization problem. Finally, the results of our analysis are verified by simulation, and they show that our method can not only optimize the PS factor efficiently, but also the model can improve the performance of the system.
Similar content being viewed by others
1 Introduction
As 5G has been commercially deployed and the intelligent devices are widely used, more and more devices are connected to wireless networks. It is applied to Internet of vehicles, smart home, intelligent reflecting surface (IRS) [1], vehicletovehicle (V2V) [2, 3] and other scenarios. The upcoming 6G wireless communication networks [4] will be designed to provide global coverage like massive Internet of things (IoT), smart cities, unmanned aerial vehicles and other applications. It can enhance energy efficiency, intelligence level and security. In the era of 6G, driven by the exponentially increasing network infrastructures and the number of connected terminals, green communication researches face new challenges such as the statistical properties, data transmission efficiency, mobility, channel modeling and power consumption. [5, 6] study channel modeling and analyze characteristics for nextgeneration communication systems. In particular, power consumption has become critical in many emerging wireless devices and has prompted researchers to reconsider the design of green networks based on energy efficiency. Therefore, green communication has become the hot research topics [7,8,9,10]. [8] provides the survey on base stations energy saving and discusses the energy problem on heterogeneous system and gives a research vision on cognitive radio and cooperative relaying system. The EHbased heterogeneous network (HetNet) in 5G is studied in [9], it gives a survey on resource allocation algorithms for different networks, and the EH technology can be used in HetNets considering energy efficiency. Two new resource allocation algorithms are provided for 6G communications. [10] gives the survey on AIbased green communications in 6G, using AI technique to manage networks and improve energy efficiency. Using wireless multihop relay architecture can extend the range of wireless communication [11], but the power consumption is an important problem if sufficient power supply is not available [12]. Traditional energyharvesting media are greatly affected by nature. Now wireless networks are spreading from ground to air, and it is extremely difficult to use traditional medium to harvest energy for these wireless networks.
Considering that wireless signal can carry and transmit energy and information at the same time, energy harvesting can prolong the service life of relay devices. [13] first introduces the concept of simultaneous wireless information and power transfer (SWIPT). [14] introduces two methods for energy harvesting, PS and time switching (TS). Particularly in TS method, the receiver node separates time to process information and harvest energy, and the TS factor is the ratio; in PS method, the receiver node splits the received signal partly for information processing and partly for the energy harvesting, and the PS factor is the ratio. Many traditional wireless technologies have been applied to EH relay networks such as multiinput multioutput (MIMO) relaying. In [15], EH in AF, DF and hybrid relaying networks with PS and TS methods over fading channel is studied, through maximizing throughput to derive the optimal ratios. Now, EH is also used for IRS wireless network [16], an IRS NOMA IoT network is studied which combines reflected energy with reflected information, and the sum throughput maximization is formulated considering phase shifts and time allocation.
Beamforming in EH relay networks can effectively increase capacity and improve the system performance. It has attracted the attention of researchers (See a survey in [17]). However, most researches focus on a relay with multiantenna network, and the research on a relay with single antenna is relatively small. Considering the limitations of devices, it is inconvenient to work with multiple antennas on a single relay. [18] proposes beamforming networks with and without directly connection from source to destination with the perfect channel state information (CSI), and the power control problem is solved with beamforming weight optimization. In [19], multigroup multicasting SWIPT relay networks are proposed. [20] analyzes the distributed antennas SWIPT system, and beamforming and PS factors are obtained under the max–min SINR constraint, using iterative algorithm by reformulating the nonconvex problem into two convex problems. The robust beamforming SWIPT problem is studied using the worstcase deterministic model in [21]. [22] studies the application of distributed beamforming technology for a dualhop cooperative MIMO DF relay network, which minimizes the probability of pairing errors and keeps the SNR above the threshold of a given relay node. The robust beamforming design in [23] is proposed in an reconfigurable intelligent surfacesaided HetNet system; using iterative method to maximize energy efficiency, the beamforming vectors and phase shifts are jointly optimized.
A twoway wireless network can improve spectrum efficiency and reduce halfduplex loss and loop interference loss in full duplex [24,25,26,27,28,29,30,31,32]. Twoway communication is also used in backscatter communication [24]. In [25], optimal beamforming vectors are attained in twoway beamforming relay network with reciprocal channels and nonreciprocal channels. [26] designs a MIMO twoway EH AF relay network; in order to minimize total meansquareerror, the optimal problem is divided into subproblems and the iterative algorithm is used, and the results demonstrate the system performance. In [27], a joint twoway beamforming and EH relay selection network is proposed, changing the relay selection problem with convex algorithm. [28] considers a SWIPT twoway relaying network with DF protocol by PS and TS method, and the PS and TS ratios are investigated through minimizing the outage probability. [29] develops beamforming SWIPT scheme in the twoway relay channel and obtains the optimal transceiver design considering maximal achievable sum rate. [30] designs the SWIPT beamforming system in the twoway relaying channel; considering AF and DF relaying protocol, the nonconvex problem is formulated, decoupling the problem into two subproblems to solve the problem. A novel harvestusestore PS relaying strategy is proposed for multirelay cooperative networks considering energy accumulation problem in [31]. [32] proposes the physicallayer network coding (PNC) based on twoway DF protocol. Compared with the digital coding arithmetic, PNC scheme can improve throughput.
In ambient backscatter communication, the system capacity can be improved by using the joint beamforming weight vector design in MIMO system with multiple antennas. But in many application scenarios, it is not easy to install multiple antennas on the device because of the work environment, volume, and the cost of frequent battery update or maintenance. Many singleantenna relays form a distributed beamforming network, which can improve the spectrum efficiency. Since the joint optimization of beamforming and PS ratio of relays is a nonconvex quadratic constrained optimization problem, most researches decouple it into two subproblems and optimize the beamforming vector and PS ratio, respectively. However, considering the complexity of the problem in real world, these methods are not suitable using multiple singleantenna EH relays in twoway beamforming system, which is still a problem that needs to be studied.
In this paper, an EH relay beamforming in AF and DF twoway mode with singleantenna relays is studied. Different from the oneway EH relaying network, the power of relays is obtained entirely by energy harvesting, and the transmit power is not limited by the total quota or the personal quota. The contributions of this paper are summarized as follows:

We propose a twoway beamforming system with EH relays. It has two transceiver nodes and many relay nodes. The transceivers are not direct linked. All the relays are single antenna. The EH relays use PS method to harvest energy and process information.

Using PSbased EH relays, we derive the formula of sum rate. It is controlled by PS factor, and optimization PS factor becomes an important issue.

A joint optimization problem is established under the sum rate maximization. The problem is nonconvex and complex. In order to get the optimal value, the gradient descent algorithm is used in AF mode, and the minimal PS factor is used under the SNR outage threshold constraint in DF mode. Based on our previous work [33] which researches on EH twoway relay network in AF mode, we further in this paper analyze the convergence results of the gradient descent algorithm, and the EH relay beamforming in DF mode is also studied.

We analyze performance by the simulation examples, and twoway beamforming scheme is better than oneway scheme both in AF and DF mode.
The remainder of the paper is organized as follows: In Sect. 2, the system is described in detail. In Sect. 3, the joint optimization PS factor is built. In Sect. 5, the simulation examples and the discussion are presented, and Sect. 6 is the conclusion.
2 System model
The twoway beamforming system is considered including two transceiver nodes and multiple relay nodes. All transceiver nodes and relay nodes are equipped with a single antenna, as shown in Fig. 1, and two transceiver nodes are not directly connected. The relay works under the AF or DF protocol with half duplex over fading channels. We assume that there are no links between relays. There are also no external interference links to relays. We assume that channel coefficients of all nodes are known, and the channel between the transceiver and the relay nodes is reciprocal. The channel gain is constant over one sendreceive block with independent and identically distributed. The mutual interference between relays can be suppressed by interference suppression which increases the system complexity. Thus, we ignore the mutual interference and assume that each relay only receives signal from two transceiver nodes. Let \(f_i\) and \(h_i\) be the channel gain between transceiver nodes to relay i. \(f_i\) and \(h_i\) is known to the transceiver and relay nodes. All the relays have no their own power supply. Their power is totally coming from energy harvesting. \(g_i\) denotes the received signal at relay i from two transceivers, and \(y_i\) is the signal sent to transceivers. \(R_{\mathrm{th}}\) is the outage threshold. The signal received at relay i from two transceivers can be written as
where \(P_0\) and \(s_i\) are the fixed transmit power and the transmit signal from two transceivers, respectively. We assume that \({\mathbb {E}}[s_1^2]=1\), \({\mathbb {E}}[s_2^2]=1\), \(v_{i}\sim CN(0,\sigma _{A}^2)\) is the additive noise introduced by relay i. \(\alpha _i\) is the PS factor which splits the received signal in two parts, information processing part is \(\alpha _i,\) and energy harvesting is \(1\alpha _i\), \(\alpha _i\in (0,1)\). The signal \(d_{in}\) is for information processing.
where \(v_{ip}\sim CN(0,\sigma _{P}^2)\) is the information processing additive noise, and the signal for energy harvesting is
2.1 AF relaying
In AF relaying mode, the relay receives signal from two transceivers; after information processing and energy harvesting, it amplifies and forwards the signal. The relay i amplifies the signal with factor \(\beta _i,\) and then sends it to two transceivers as shown in Fig. 2. The relay i sends the signal amplified by the factor \(\beta _i\) to two transceivers with phase adjusted by \(\theta _i\)
The average transmit power is
and according to the PS method, the average power harvesting is
Because the relay i has no its own power supply, the harvested energy for relay at least is equal to its transmit power
where \(\xi\) is the energy conversion efficiency. Therefore,
We assume that \(\alpha _i P_0 f_i^2+\alpha _i P_0 h_i^2 + \alpha _i \sigma _A^2 \gg \sigma _P^2\), so \(\beta _i\) be written as
The signal received at transceivers s1 and s2 from multiple relays by maximal ratio combination (MRC) is:
where \(w_1\sim CN(0,\sigma _{D1}^2)\) and \(w_2\sim CN(0,\sigma _{D2}^2)\) are the additive noise introduced by the antenna at transceivers s1 and s2. M is the number of relay nodes. Considering the selfinterference constraint (SIC), by eliminating the selfinterference component, \(s_1^\mathrm{AF}\) and \(s_2^\mathrm{AF}\) are further transformed as
Therefore, the SNR in AF mode at transceivers s1 and s2 is given by
Obviously, when \(\theta _i=\arg f_i\arg h_i\), the maximal SNR is obtained. By substituting \(\theta _i\) in (14) and (15), we have
Then, the achievable rate from s1 to s2 and from s2 to s1 is given, respectively.
The sum rate for AF relaying protocol is defined as
The outage probability at node s1 and s2 is
Both links from s1 to relays to s2 and from s2 to relays to s1 should keep communication by the relayed path. To keep the twoway communication well, the outage probability is the sum of outage probability at s1 and s2.
2.2 DF relaying
When the relay i works in DF mode, as shown in Fig. 3, after information processing and energy harvesting, the relay forwards information to transceivers. The relay node i receives signal from two transceivers with physicallayer network coding (PNC) scheme [34]. We have
\(v_{1i}\sim CN(0,N_0)\) and \(v_{2i}\sim CN(0,N_0)\) is the additive noise introduced by the relay i antenna. \(v_{i}\sim CN(0,N_0)\) is the additive noise introduced by the relay i antenna. Using the power splitting technique, the energy that the relay i harvests from s1 and s2 is given as
The relay i uses its power \(E_{ri}^\mathrm{DF}\) to send information. Here, we assume the relay i can successfully decode and encode signal without error. In this way, the SNR at the relay node i from s1 is
the SNR at the relay node i from s2 is
the SNR at the relay node i from s1 and s2 is
because we assume the relay i can successfully decode and encode signal without error, so the signaltonoise ratio is greater than outage threshold of node s1 and s2. Then,
where \(r_{\mathrm{th}}\) is the SNR outage threshold, and we can get that
Obviously,
Since \(\alpha _i\) is known to be smaller than 1, we have
Therefore, the signal sent by relay i is given by
where \(P_{r_i}^\mathrm{DF}\) is the transmit power of relay node i. To let the relay work in normal state, the power harvested should be equal to its transmit power, i.e.,
Therefore,
Then, the relays forward information to destinations using harvested energy. Again, considering SIC, after eliminating the selfinterference component, the received signal at destination \(s_1\) and destination \(s_2\) is given by
where \(w_{z1}\sim CN(0,N_0)\) and \(w_{z2}\sim CN(0,N_0)\) are the additive noise introduced by the transceiver antenna. Therefore, the SNR at destination node is
the achievable rate of node s1 is
the achievable rate of node s2 is
and the sum rate at destination nodes is
The outage probability at node s1 and s2 is given by
The sum outage probability is
From (45), we can observe that maximizing \(R_{d}^\mathrm{DF}\) under constraint (35) can be achieved by simply optimizing the variable \(\alpha _i\).
3 Joint PS factor optimization
In this paper, we consider the sumrate maximization for the PS factor optimization problem.
3.1 AF relaying
By substituting \(R_1^\mathrm{AF}\) and \(R_2^\mathrm{AF}\) in (18) and (19), we have
Our objective is to maximize \(R^\mathrm{AF}\) given by
However, we cannot derive the closed form of \(R^\mathrm{AF}\). Because \(\log _2()\) is the monotonic increasing function, the gradient descent algorithm can be used to solve the optimization problem. We need to change the maximal problem to the minimal problem and change the constrained problem to an unconstrained problem. Our objective can be reformulated as
where \(R_{\mathrm{min}}^\mathrm{AF}\) is the minus of \(R^\mathrm{AF}\).
where \(\alpha _{i} \in (0,1)\). As well known, gradient descent method is one of the efficient methods to solve unconstrained optimization problem, and we can transform the constrained problem into an unconstrained problem. \(\alpha _{i}\) is the only constrained condition. In order to solve the optimization problem easily, we use the following variable substitution to transform constrained problem about \(\alpha _{i}\) into an unconstrained problem.
where \(x \in [\infty ,\infty ]\). Gradient descent method is one of the efficient methods to solve unconstrained optimization problem, which always converges to a local minimum point. By multiple random initialization, an optimal value from several local minimum point can be chosen and can be considered as global minimum point. Since it is difficult to get the gradient of \(R_{\min }^{A F}(x)\), the secant method is used as the approximate of gradient.
where \(\delta\) is a vector with a very small norm. We can choose \(\delta = 10^{8}e_i\) to get \(\frac{\partial R_{\min }^{A F}(x)}{\partial x_i}\), where \(e_i\) is a vector whose ith element is 1 and the others are all 0. For the required step size of each iteration, the initial step size is set as \(\lambda = 100\), which will be adjusted in each iteration.
3.2 DF relaying
Different from the AF relaying protocol, transmit signal under the DF relaying protocol will not suffer from the problem of noise propagation. For the DF mode, the sum rate of destination nodes can be evaluated and defined as
By substituting \(R_{d}^\mathrm{DF}\) in (45), \(R^\mathrm{DF}\) can be rewritten as
Our goal is to find the PS factor to maximize the sum rate, which is obviously equivalent to maximizing \(R^\mathrm{DF}\). We find that the \(\log _2()\) is a monotonic increasing function, the term on the righthand of (55) is quasiconvex, and when the value of \(\alpha _i\) is small, we can get the maximum \(R^\mathrm{DF}\). Based on (35), the optimal PS ratios and the sum rate can be determined when \(\alpha _i =\dfrac{r_{\mathrm{th}} N_0}{P_0}max\left\{ \dfrac{1}{f_i^2},\dfrac{1}{h_i^2}\right\} .\)
4 Results and discussion
We present numerical simulations to verify the performance of our proposed twoway relaying beamforming scheme. The number of relay nodes is 2–8, and the channel coefficients are assumed to be independent and reciprocal variables. The additive noise is assumed to be unit variance and power spectral density to be − 174 dbm/Hz. The bandwidth is assumed as 10 mHz, the energy efficiency is 80%, and the SNR outage threshold is 5 db.
4.1 Sumrate maximization
The results are presented in Fig. 4. We first consider the AF relaying network with 2, 4, 6, 8 relay nodes and compare the sum rate, and the transmit SNR is 5–25 db. It is obvious that the sum rate is higher when more relays are used. As the number of relay nodes increases, twoway beamforming systems harvest more energy and extend the relay lifetime and improve the performance.
The convergence results of the gradient descent algorithm for AF mode are depicted in Figs. 5 and 6. With enough iteration steps, even if the initial points are different, the sum rate always converges to the same stationary point, and the norm of gradient always converges to zero. Therefore, the local minimum point obtained by the gradient descent algorithm can almost surely be regarded as the global minimum point.
Then, we consider the DF relaying network also with 2, 4, 6, 8 relay nodes and compare the sum rate at destinations with our proposed PS factor optimization method. The results are shown in Fig. 7. As can be observed, with more transmit power and relay nodes, the sum rate will increase.
Then, we compare the sum rate of different cooperative schemes with varying SNR at sources, while the number of relay nodes is set 6. As shown in Fig. 8, it includes greedy general relay selection (SWGRS) [33], oneway AF relaying (SWAF) [33], oneway DF relaying (SWDF) and our proposed twoway AF relaying (TWBAF) and twoway DF relaying (TWBDF). It is seen that our proposed twoway relaying network scheme is better than oneway scheme both in AF and DF mode. Working in twoway DF mode can get higher rate than working in AF mode.
We also compare the sum rate of different cooperative schemes with varying number of relays with the same source transmit SNR 25 db. The results are shown in Fig. 9. With the same transmit SNR, the performance between TWBAF and TWBDF is different. The sum rate of TWBDF scheme is higher than that of TWBAF scheme. As we assume that the relays can decode the received signal without error in DF mode, we only need to harvest more energy in DF mode, and the sum rate at destinations is just considered.
4.2 Outage probability performance
The sum outage probability performance among different transmit SNRs and relays in TWBAF scheme is presented in Fig. 10. It is obtained by Monte Carlo simulation. We can see that the outage probability is lower when the number of relays is more and transmit power is higher, and it is consistent with the sumrate curve.
In Fig. 11, the sum outage probability performance among different SNRs with different relays is presented for TWBDF scheme by Monte Carlo simulation. When the number of relay nodes is more than 6, and SNR is more than 15 db, it is close to 0. We can see that the outage probability is lower when the number of relays and transmit power increase, and it is in accordance with the sumrate curve of TWBDF.
4.3 Optimal PS factor
According to the results as shown in Table 1, we find that in AF mode the optimal PS factor is about 0.68. It means more of the received signal at relay nodes is used to information processing. In DF mode as shown in Table 2, the optimal PS factor is small. It means that the received signal at relay side is mainly used for energy harvesting. That is because we assume that the relay nodes can decode and encode signal without error and can only maximize the sum rate at destinations.
5 Conclusions
In this paper, we investigate the AF and DF twoway network beamforming EH relaying networks. For effective network beamforming by the EH relays, we propose to use the gradient descent algorithm in AF mode and use the smallest PS factor at relays under the SNR threshold for DF mode to enable an efficient solution. It is seen that the performance gain is significant with more relays and higher transmit SNR.
6 Methods
Our system includes two transceiver nodes and multiple relay nodes. All nodes are equipped with a single antenna. Two transceiver nodes are not directly connected. It works under the AF or DF protocol with half duplex over fading channels. The power of all the relays is totally coming from energy harvesting. Two to eight relay nodes are analyzed, and the channel coefficients are independent and reciprocal variables. The bandwidth is assumed as 10 mHz, the energy efficiency is 80%, and the SNR outage threshold is 5 db. The performance analysis is shown in the form of sumrate maximization and outage probability performance.
6.1 Sumrate maximization
The sumrate maximization is used for joint PS factor optimization problem. Because we cannot derive the closed form of the sum rate, we use the gradient descent algorithm to solve the problem in AF mode and obtain the optimal PS factor when the PS factor is the smallest at relays under the SNR threshold in DF mode.
6.2 Outage probability performance
The sum outage probability performance among different SNRs with different relays is presented for TWBAF and TWBDF scheme by Monte Carlo simulation.
Availability of data and materials
Data were randomly generated when we were running program.
Abbreviations
 EH:

Energy harvesting
 PS:

Power splitting
 TS:

Time switching
 AF:

Amplifyandforward
 DF:

Decodeandforward
 IRS:

Intelligent reflecting surface
 HetNet:

Heterogeneous network
 V2V:

Vehicletovehicle
 IoT:

Internet of things
 SWIPT:

Simultaneous wireless information and power transfer
 MIMO:

Multipleinput multipleoutput
 CSI:

Channel state information
 PNC:

Physicallayer network coding
References
H. Jiang, C. Ruan, Z. Zhang, J. Dang, L. Wu, M. Mukherjee, D.B. de Costa, A general wideband nonstationary stochastic channel model for intelligent reflecting surfaceassisted MIMO communications. IEEE Trans. Wirel. Commun. 20(8), 5314–5328 (2021)
H. Jiang, B. Xiong, Z. Zhang, J. Zhang, H. Zhang, J. Dang, L. Wu, Novel statistical wideband MIMO v2v channel modeling using unitary matrix transformation algorithm. IEEE Trans. Wirel. Commun. 20(8), 4947–4961 (2021)
P.S. Bithas, G.P. Efthymoglou, A.G. Kanatas, V2v cooperative relaying communications under interference and outdated CSI. IEEE Trans. Veh. Technol. 67(4), 3466–3480 (2018)
Y.L. Lee, D. Qin, L.C. Wang, G.H. Sim, 6g massive radio access networks: key applications, requirements and challenges. IEEE Open J. Veh. Technol. 2, 54–66 (2021)
H. Jiang, M. Mukherjee, J. Zhou, J. Lloret, Channel modeling and characteristics for 6g wireless communications. IEEE Netw. 35(1), 296–303 (2021)
H. Jiang, Z. Zhang, B. Xiong, J. Dang, L. Wu, J. Zhou, A 3d stochastic channel model for 6g wireless doubleirs cooperatively assisted MIMO communications, in 2021 13th International Conference on Wireless Communications and Signal Processing (WCSP) (2021), pp. 1–5
Y. Lu, Y. Zhao, Trend and strategy: energy consumption and carbon emissions in Beijing, in Proceedings of the 2011 International Conference of Information Technology, Computer Engineering and Management Sciences, vol. 3 (2011), pp. 353–355
Z. Hasan, H. Boostanimehr, V.K. Bhargava, Green cellular networks: a survey, some research issues and challenges. IEEE Commun. Surv. Tutor. 13(4), 524–540 (2011)
Y. Xu, G. Gui, H. Gacanin, F. Adachi, A survey on resource allocation for 5g heterogeneous networks: current research, future trends, and challenges. IEEE Commun. Surv. Tutor. 23(2), 668–695 (2021)
B. Mao, F. Tang, Y. Kawamoto, N. Kato, Ai models for green communications towards 6g. IEEE Communications Surveys Tutorials 66, 1 (2021)
F. Khan, Capacity and range analysis of multihop relay wireless networks, in Proceedings of the IEEE Vehicular Technology Conference (2006), pp. 1–5
K.T. Phan, T. LeNgoc, S.A. Vorobyov, C. Tellambura, Power allocation in wireless multiuser relay networks. IEEE Trans. Wirel. Commun. 8(5), 2535–2545 (2009)
L.R. Varshney, Transporting information and energy simultaneously, in 2008 IEEE International Symposium on Information Theory (2008), pp. 1612–1616
R. Zhang, C.K. Ho, MIMO broadcasting for simultaneous wireless information and power transfer. IEEE Trans. Wirel. Commun. 12(5), 1989–2001 (2013)
S. Atapattu, J. Evans, Optimal energy harvesting protocols for wireless relay networks. IEEE Trans. Wirel. Commun. 15(8), 5789–5803 (2016)
X. Li, Z. Xie, Z. Chu, V.G. Menon, S. Mumtaz, J. Zhang, Exploiting benefits of irs in wireless powered noma networks. IEEE Trans. Green Commun. Netw. 6(1), 175–186 (2022)
Y. Alsaba, S.K.A. Rahim, C.Y. Leow, Beamforming in wireless energy harvesting communications systems: a survey. IEEE Commun. Surv. Tutor. 20(2), 1329–1360 (2018)
Y. Jing, H. Jafarkhani, Network beamforming using relays with perfect channel information, in Proceedings of the 2007 IEEE International Conference on Acoustics, Speech and Signal Processing—ICASSP’07, vol. 3 (2007), pp. III473–III476
Ő.T. Demir, T.E. Tuncer, Distributed beamforming in relay networks for energy harvesting multigroup multicast systems, in Proceedings of the 2016 IEEE International Conference on Acoustics, Speech and Signal Processing (ICASSP) (2016), pp. 3296–3300
Z. Zhu, S. Huang, Z. Chu, F. Zhou, D. Zhang, I. Lee, Robust designs of beamforming and power splitting for distributed antenna systems with wireless energy harvesting. IEEE Syst. J. 66, 1–12 (2018)
Z. Xiang, M. Tao, Robust beamforming for wireless information and power transmission. IEEE Wirel. Commun. Lett. 1(4), 372–375 (2012)
N.D. Suraweera, K.C.B. Wavegedara, Distributed beamforming techniques for dualhop decodeandforward MIMO relay networks, in Proceedings of the 2011 6th International Conference on Industrial and Information Systems (2011), pp. 125–129
Y. Xu, H. Xie, Q. Wu, C. Huang, C. Yuen, Robust maxmin energy efficiency for risaided hetnets with distortion noises. IEEE Trans. Commun. 70(2), 1457–1471 (2022)
H. Wang, J. Jiang, G. Huang, W. Wang, D. Deng, B. Elhalawany, X. Li, Physical layer security of twoway ambient backscatter communication systems. Wirel. Commun. Mob. Comput. 2022, Article ID 5445676 (2022)
M. Zeng, R. Zhang, S. Cui, On Design of Distributed Beamforming for Twoway Relay Networks (2010), pp. 882–886
Y. Chen, Z. Wen, S. Wang, J. Sun, M. Li, Joint relay beamforming and source receiving in MIMO twoway af relay network with energy harvesting, in 2015 IEEE 81st Vehicular Technology Conference (VTC Spring) (2015), pp. 1–5
M. Tian, W. Sun, L. Huang, S. Zhao, Q. Li, Joint beamforming and relay selection in af twoway relay networks with energy transfer. IEEE Syst. J. 14(2), 2597–2600 (2020)
T.P. Do, I. Song, Y.H. Kim, Simultaneous wireless transfer of power and information in a decodeandforward twoway relaying network. IEEE Trans. Wirel. Commun. 16(3), 1579–1592 (2017)
Z. Fang, X. Yuan, X. Wang, Distributed energy beamforming for simultaneous wireless information and power transfer in the twoway relay channel. IEEE Signal Process. Lett. 22(6), 656–660 (2015)
W. Wang, R. Wang, H. Mehrpouyan, N. Zhao, G. Zhang, Beamforming for simultaneous wireless information and power transfer in twoway relay channels. IEEE Access 5, 9235–9250 (2017)
G. Huang, W. Tu, On opportunistic energy harvesting and information relaying in wirelesspowered communication networks. IEEE Access 99, 1 (2018)
S. Zhang, S.C. Liew, Applying physicallayer network coding in wireless networks. EURASIP J. Wirel. Commun. Netw. 6, 66 (2010)
H. Sun, F. Han, H. Deng, Energyharvesting relaying in twoway af beamforming network, in 2021 13th International Conference on Wireless Communications and Signal Processing (WCSP) (2021), pp. 1–5
S.C. Liew, S. Zhang, L. Lu, PhysicalLayer Network Coding: Tutorial, Survey, and Beyond (2011)
Acknowledgements
Thanks for our professor Rongqing Zhang giving us a lot of comments and suggestions that have helped us improve the quality and presentation of our manuscript.
Funding
This work was supported in part by the National Key Research and Development Project under Grant 2019YFB2102300, in part by the National Natural Science Foundation of China under Grant 61936014, in part by Shanghai Municipal Science and Technology Major Project No. 2021SHZDZX0100, in part by Natural Science Foundation of Shanghai under Grant 22ZR1463400, in part by Shanghai Sailing Program under Grant 21YF1450100 and in part by Fundamental Research Funds for the Central Universities.
Author information
Authors and Affiliations
Contributions
H.S. wrote the original draft. F.X.H., S.J.Z. and H.D. reviewed and edited the draft. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare that they have no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sun, H., Han, F., Zhao, S. et al. Optimal energyharvesting design for AF and DF twoway relay beamforming in 6G. J Wireless Com Network 2022, 73 (2022). https://doi.org/10.1186/s1363802202155x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s1363802202155x