Abstract
Background
The contamination of aquatic ecosystems with both anthropogenic pollutants and particles in particular (microscopic) plastic debris items is of emerging concern. Since plastic particles can accumulate contaminants and potentially facilitate their transport, it is important to properly investigate sorption mechanisms. This is especially required for a large variety of chemicals that can be charged under environmental conditions and for which interactions with particles may hence go beyond mere partitioning.
Results
In this study, sorption experiments with two types of microplastic particles (polyethylene and polystyrene) and 19 different contaminants (pesticides, pharmaceuticals, and personal care products) were performed at three different pH values. We could show that sorption to plastic particles is stronger for hydrophobic compounds and that neutral species usually contribute more to the overall sorption. Bulk partitioning coefficients were in the same order of magnitude for polyethylene and polystyrene. Furthermore, our results confirm that partition coefficients for polar compounds can only be accurately determined if the solid-to-liquid ratio in batch experiments is more than 6–7 orders of magnitude higher than any plastic concentration detected in the environment. Consequently, only a minor fraction of pollutants in water bodies is associated with microplastics.
Conclusions
Although neutral species primarily dominate the overall sorption, hydrophobic entities of ionic species cannot be neglected for some compounds. Notwithstanding, our results show that since microplastic concentrations as currently observed in the environment are very low, they are only a relevant sorbent for strongly hydrophobic but not for polar compounds.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction and background
Chemical pollution is of emerging concern and has even been considered to be a planetary boundary threat [6, 32]. In addition, contamination with anthropogenic litter such as microplastics raises public concern [3, 15, 27]. Since, in freshwaters, pollutants distribute between the freely dissolved water phase and natural but also anthropogenic particles, microplastics may be an additional vector for spreading pollutants [20]. Therefore, one important aspect is to assess the impact of particle-bound contaminants. Since transport of particles and associated contaminants, i.e., for particle-facilitated transport, is different compared to purely dissolved chemicals [2], sorption/desorption kinetics, and thus, particle properties such as density, shape, material, and size are decisive. Sorbed contaminants are less available for biodegradation and may, therefore, be transported further than chemicals freely available in the aqueous phase that are more easily prone to transformation processes [1, 10]. Furthermore, determined partition coefficients can serve for an improved understanding of sorption processes and, hence, a deepened risk assessment of sorbed contaminants. For compounds with slow desorption kinetics, i.e., with high partition coefficients [36], microplastics may act as transport vectors, whereas they act as passive samplers and reflect the ambient concentration of the organic pollutants in the environment as soon as sorption equilibrium is reached. In both cases, partition coefficients are crucial to calculate (i) characteristic times for contaminant release and (ii) the ambient concentration (e.g., in the water) at the sampling location. Kinetics and impact of partition coefficients are thoroughly discussed in Seidensticker et al. [36]. In freshwater systems, one major path for microplastics to enter rivers is via the effluent of wastewater treatment plants where large numbers of particles have been observed [28, 29]. In such effluents, however, also high concentrations of micropollutants such as pharmaceuticals and pesticides occur [12, 13, 23, 35]. Therefore, plastic particles might especially act as a sorbent and potential transporter for frequently occurring wastewater contaminants, and are, hence, a factor that needs to be considered if the environmental fate of micropollutants is examined.
Depending on their physico-chemical properties, many pollutants dissociate under certain pH conditions, and hence, their fate and behavior in the environment is strongly influenced by changes in the pH [5, 19]. Among these ionizing chemicals are pesticides, flame retardants, but also pharmaceuticals and further household chemicals like detergents. From studies with natural particles and sediments, it is known that sorption interaction mostly takes place between sorbents and neutral species and that charged compounds sorb only little or not at all [11, 19]. Unlike many natural particles, microplastics can be charged electrostatically [37, 41]. Therefore, the uptake of ionizable substances theoretically might not only determined by mere partitioning between microplastic particles and the neutral species but also by possible ionic bounds. Sorption interactions between charged species and different types of microplastics have not been extensively studied so far. Thus, the aim of our study was to clarify the sorption behavior to microplastics in freshwater under varying pH of five neutral substances (as control) and a set of 14 selected ionizable compounds including pesticides and insecticides, but also pharmaceuticals, detergents, and flame retardants that represent trace pollutants emitted via the wastewater treatment plant. Pristine polyethylene and polystyrene particles were used, since, in the wastewater canalization system, “young” particles occur and enter the WWTP where they get in contact with various (emerging) contaminants such as pharmaceuticals and personal care products which we used in this study. Both plastic types are among the most abundant in WWTP (as, e.g., reported in Mintenig et al. [28] and Murphy et al. [29]).
Methods
Chemicals
In total, 19 different chemicals were tested for their sorption interactions with different microplastics. These chemicals include seven bases with dissociation constants (pKa) ranging from 1.09 to 8.37, eight acids covering pKa values of 3.13–13.9, and four neutral substances. Details on the physico-chemical properties of these compounds are listed in Table 1.
All chemicals except phenanthrene were purchased from LGC standards (Wesel, Germany). The latter was purchased from Sigma-Aldrich Supelco (Bellefonte, PA, USA).
Polyethylene (PE) and polystyrene (PS) were used as representative types of microplastics, and were purchased from Azelis (trade name Gotalene 120, Moers, Germany) and Goodfellow Cambridge Ltd. (Huntingdon, UK), respectively. Sizes of polyethylene and polystyrene microparticles were given by the supplier (uniform size distribution with mean sizes of 260 and 250 µm, respectively), and confirmed by visual inspection under SEM (see images in the Additional file 1). Particles with comparable sizes were chosen to better compare sorption mechanisms and to exclude huge differences due to size effects. Furthermore, N2-BET surface areas were measured and revealed that PE is non-porous, while PS is mesoporous with an average pore size of ~ 195 Å. According to Pascall et al. [31], glass transition temperatures Tg of polyethylene and polystyrene are in the range of − 120 and 100 °C, respectively.
Batch experiments
To study equilibrium partitioning of charged and non-charged compounds, we performed batch experiments with ultrapure water (electric conductance of 0.057 µS cm−1) and microplastic particles at three different pH levels (4, 7, and 10) and the mix of selected substances. For all compounds, the initial concentrations in the water phase were around 5 µg L−1 except for phenanthrene and nonylphenol. Due their high hydrophobicity, these two substances were expected to sorb very strongly. Therefore, the initial concentrations were 50 and 30 µg L−1, respectively, to avoid aqueous concentrations below the detection limit. The initial concentrations of all substances were below 1% of their water solubility to avoid competitive sorption. The batches were spiked from an aqueous contaminant solution to avoid co-solvent effects of organic solvents. Either formic acid or ammoniac was used to adjust the pH in the batches. For preparing the neutral solution, 0.02 M Na2PO4 (Rotifair, Carl Roth) was used. For each pH, the solutions were prepared in one glass vessel before they were distributed into the single batches. During the experiments, frequent pH measurements were performed to control the stability. All experiments were prepared in ultrapure water and performed in amber glass bottles to avoid biodegradation and photo-oxidation. Blanks were included to confirm that neither biodegradation nor sorption to glass walls or seals, etc. takes place. The liquid-to-solid ratio in the batches was 0.001 kg L−1, namely 100 mg of microplastics in 100 mL of solution. Batch experiments for each pH were performed in triplicates and samples of 2 × 1 mL were taken at the beginning (t = 0) to quantify the actual initial concentration. Further samples were taken after 2, 4, 7, and 11 (only for PS) days to measure the overall partitioning of the substances and to ensure that equilibrium was reached within the batches. Samples were taken from completely independent batches, and all samples were considered to take outliers into account, as well. For detailed studies on kinetics and conformation of fast equilibration, see Seidensticker et al. [36]. The bottles were constantly shaken on a horizontal shaker with a rotational speed of 150 rpm and kept in a dark room tempered to 20 °C. The sampling procedure ensured that the liquid-to-solid ratio changed less than 10%. Thus, this minor change was neglected in the subsequent data analysis, since it is in the range of the analytical error. As discussed below, only partition coefficients larger than 50 L kg−1 can be reliably determined, since, at larger liquid-to-solid ratios, the measurement errors escalate. Therefore, all data resulting in smaller partition coefficients are not reported. Furthermore, the coefficients of variation (CV) have been calculated as the standard deviation normalized to the mean values of the replicates and given in %. CV values > 100% were as well a criterion for exclusion.
Chemical analysis
Phenanthrene, nonylphenol, and TCPP were quantified via GC–MS. For analysis, an Agilent 6890N GC coupled to an Agilent 7973 inert MS was used. For separation, a J + W Scientific DB-5MS (30 m length, 0.025 mm ID, and 0.25 µm film thickness) capillary column was used. The device was operated in a pulsed splitless mode with a Helium flow of 0.7 mL min−1. Samples were taken as described above and internal standards (Phenanthrene-D10 and 4-n-Nonylphenol-D8) were added. Subsequently, the samples were extracted with 400 µL of cyclohexane, shaken overnight, and measured.
The other 16 substances were quantified with LC–MS/MS and samples were directly injected after gravitational phase separation. Since the LC system is equipped with a pre-column filter, remaining particles would not be able to enter the column and to produce false-positive results. For quantification, a calibration curve with nine different concentration levels from 0.025 to 10 µg L−1 was generated. For analysis, an Agilent 1290 infinity LC coupled to an Agilent 6490 Triple Quadrupole was used. Separation was performed with an Agilent InfinityLab C18 poroshell column (length 100 mm, 2.1 µm ID). For elution, water (with 0.1% acetic acid and 0.01 mM ammonium acetate) and acetonitrile (ACN, with 0.1% acetic acid) were used. The gradient elution looks as follows (with percentage of ACN): start with 2%, stepwise increase to 80% until 17 min, 100% until 23 min, then again 2% until 32 min. For the quantification of the samples from the batch experiments with either triclosan or diclofenac, two isocratic methods with 57% ACN or 70% ACN were used, respectively. For these measurements, specific calibration curves were generated, as well (concentration range from 0.5 to 250 µg L−1 with seven calibration levels). Substances were ionized with an ESI source operated either in positive mode or negative mode. Details on the ionization mode, mass transitions, and other analytical characteristics are reported in the Additional file 1.
Model-based data analysis
Linear partitioning of a substance between two phases, here water and a type of microplastics, is given as the equilibrium partition coefficient KP (L kg−1), i.e., the concentration ratio of the sorbed [Cp in (µg kg−1)] and dissolved [Cw in (µg L−1)] fraction:
For ionizable compounds, the pH-dependent partition coefficient DP can be calculated as follows:
where fn and fi are the fractions of the neutral and ionized species, and KP,n and KP,i are the species-specific partition coefficients for the neutral and the ionized species, respectively. fn and fi were calculated from the known pKa and pH values according to the rearranged Henderson–Hasselbalch equation, while the species-specific partition coefficients were deduced from fitting the calculated DP value to the experimentally determined DP values. At each pH and for each substance, DP was calculated from 9 or 12 measured aqueous concentrations for PE and PS, respectively. No measurement results were excluded. For the fitting procedure, a MATLAB Code (Version R2017b) was used. Within this code, a non-linear least-squares solver was used to calculate KP,n and KP,i from fitting Eq. 2 to measured DP values. This procedure allows calculating a theoretical DP for each substance over the full pH range. To assess the uncertainty of the determination of partition coefficients, a simple error evaluation was considered as follows:
with KP,c and KP,m as the calculated and measured partition coefficients, respectively, and VW, mP, and ε denote the volume of water, the mass of particles, and the uncertainty of the measurement (e.g., a standard deviation).
Aqueous pollutant concentrations under two different microplastic scenarios
Experimental results on the overall sorption coefficients of the investigated substances at three pH values were used to calculate two scenarios with different microplastic concentrations. In both scenarios, organic carbon (values for KOC were taken from US EPA EPISuite 4.1 and apply for the so-called “normal” soil organic matter) was present as a natural sorbent which can compete for the sorbates and is able to act as a vector, as well. To compare the results from our experiments with an environmental relevant setting, two different liquid-to-solid ratios (LSR) concerning the amount of plastics were chosen. To match our experimental conditions, in Scenario I, a LSR of 103 L kg−1 and to reflect particle concentrations closer to current environmental conditions in Scenario II, an LSR of 1010 L kg−1 (comparable to conditions at the effluent of WWTPs, according to particle concentrations recorded by Mintenig et al. [28]) were chosen. The mass of organic carbon was set to 10 mg, i.e., a concentration of 10−5 kg L−1. The dissolved fraction \({f_{\text{diss}}}\) in the water, i.e., the ratio between the equilibrium and the initial concentration, may be easily calculated as follows:
Here, VW, mOC, and mP denote the volume of water, the mass of organic carbon, and the mass of plastic particles, respectively. Each scenario was calculated over a range of KOC and KP values and for the three different pH values that were used in the experiments. For the investigated substances, KP was quantified with the particle-water partition coefficient that was experimentally determined.
Results and discussion
Equilibrium sorption to PE
Sorption to PE is, in general, strongly dependent on the substance properties and is mostly driven by partitioning. Polymer properties as, e.g., density [30], branching of polymer chains and crystallinity [8] may, as well, influence sorptive interactions. Sorption of non-polar compounds is stronger than sorption of polar compounds, and sorption of charged species is weaker than sorption of neutral species (Fig. 1). Fluctuations of sorbed percentages will be discussed below. Detailed sorption plots of every substance and the respective agreement with the model can be found in the Additional file 1. In general, the model could be fitted to the measured overall partition coefficients quite well. The derived KPE,n and KPE,i are listed in Table 2; to secure reliability, exact values were only reported if KPE were > 50 L kg−1 and/or CV were < 100%. Even though it is expected that the species-specific partition coefficient of the ions is zero or close to zero, for some compounds, the species-specific partition coefficients indicate that the charged species contribute to sorption, as well. For these cases, the KPE,i’s difference from zero is greater for weakly sorbing compounds. These results will be discussed in more detail below.
For some substances, sorption did not significantly decrease with increasing share of ionized species, indicating that structural features as, e.g., the hydrophobic neutral tail of the surfactant-like nonylphenol are responsible for sorptive interactions.
Equilibrium sorption to PS
Sorption to PS was stronger than sorption to PE for most of the investigated substances and driven by both partitioning and adsorption (e.g., a pore-filling mechanism confirmed by the non-linear sorption isotherms (as provided in the Additional file 1) which is in agreement with the findings of other authors [16, 39]. Nevertheless, sorption coefficients for both plastic types are within the same order of magnitude. Furthermore, in analogy to the case for PE, sorption to PS was driven by hydrophobicity as well and substances that sorbed strongly to PE also sorbed strongly to PS (Fig. 2). Detailed plots of measured and modeled DP for all substances can be found in the Additional file 1. Again, the model could be fitted to measured overall partition coefficients well and, again, the model fits were better for stronger sorbing compounds. Based on the deduced KPS,n and KPS,i, sorption of neutral species to PS is stronger than to PE, whereas sorption of the ionic species is weaker for most of the substances (Tables 2 and 3).
Coefficients of variation increase with increasing share of ionic species, thus decreasing sorption which leads to the conclusion that for weakly sorbing ionic species the error escalates. Differences between sorption to PE and PS can most likely be explained due to the non-linearity of sorption to PS. Consideration of the differences between ambient concentrations and water solubility is crucial if non-linear sorption mechanisms are investigated. Studies performed, e.g., by Hüffer and Hofmann [16] and Lee et al. [21] determined higher partition coefficients for PS, whereas other studies by Pascall et al. [31] indicate stronger sorption to PE. In general, there is a lack of experiments comparing sorption to different types of microplastics. Experiments performed in our own lab showed that sorption of a polycyclic aromatic hydrocarbon (phenanthrene) and two heterocyclic compounds to PE and PS was stronger for PE and revealed a slight non-linearity of sorption isotherms to PS (reported in the Additional file 1). Therefore, we conclude that sorption to PE is driven by partitioning, i.e., absorption, whereas sorption to PS may be driven by both adsorption and subsequent pore-filling mechanisms which are confirmed by the non-linear sorption isotherms. According to the high glass transition temperature of PS, the free volume within the polymeric matrix is low, and hence, adsorption is favored in comparison to absorption [31]. As there are many producers of plastics using different ingredients, the differences between the same types of plastics can be as manifold as the number of manufacturers. Hence, the outcome of such sorption experiments can be different depending on the material supplier and comparability is, in general, difficult.
Sorption of the ionic species
As expected, the species-specific partition coefficients for most substances were higher for the neutral species; the ionic species of some substances showed some significant sorption, as well. This occurred especially for more hydrophobic substances such as nonylphenol and triclosan, whereas, for weakly sorbing compounds, species-specific partitioning coefficients of the ionic species were at least one order of magnitude smaller. Whereas predictions solely based on the log KOW which is the classic parameter for estimating hydrophobicity fail to predict accumulation of ionic species [9], there is some evidence that polar species can accumulate within organisms as well and play an important role in bioaccumulation in fat [7, 14]. In addition, carbon nanotubes can sorb ionic liquids [40].
Impact of particle concentration
The best practice to sensitively measure partition coefficients is to choose a liquid-to-solid ratio (LSR) in the same range or lower as the prospective partition coefficient that should be determined. This allows determination of the partition coefficient with a sufficiently low uncertainty. In our experiments, the LSR was 103 L kg−1, and thus, only partition coefficients greater than 103 L kg−1 or slightly smaller (> 50 L kg−1) can be determined with small errors. As it can be seen in Fig. 3, the partition coefficients determined for polar and weakly sorbing compounds are subject to greater uncertainty, and the deviation between the calculated and the measured partition coefficients increases with decreasing sorption independent of the pH. Therefore, the partition coefficients determined for polar and weakly sorbing compounds are subject to greater uncertainty which is reflected in the variation coefficients.
Uncertainty of partition coefficients calculated according to Eq. 3. Uncertainties were determined with standard analytical errors of ε = ± 5% (dotted lines) and of ε = ± 10% (dashed lines). The differences between the measured DP (x-axis) and the calculated DP (y-axis) are displayed by the black and red symbols for PE and PS, respectively. Crosses, circles, and pluses indicate DP values determined at pH 4, pH 7, and pH 10, respectively
An LSR of 103 L kg−1 as chosen in our batch experiments represents microplastics concentrations that are orders of magnitude larger than the ones that were detected in the environment where LSRs are usually > 109 L kg−1 [20, 28, 34]. Thus, batch setups focusing on elucidating a specific process detail, like the species-specific sorption coefficients in this study, do not reflect environmental relevant conditions, in particular when considering that plastic debris is just a very minor fraction compared to all natural particles that environmental contaminants can partition to. In addition, for most of the substances investigated within this study, the determined DPs were below the order of 101 to 102 L kg−1, i.e., the lower the particle concentration, the smaller is the mass flux of the substance into the solid phase and, with this, the resulting highly uncertain measurements of KP. Therefore, adsorption efficiencies reported in the literature (e.g., 60 and 70% for PFC sorption to PE and PS; [25] are only possible under very low (and thus unrealistic) LSRs.
This is even more true under environmental conditions as there are more sorbing phases such as black carbon or dissolved organic matter available which take up contaminants as well and partly even much stronger than polymers [4]. Calculations on equilibrium distribution in a freshwater system containing natural sorbents (organic carbon) and microplastic particles show that microplastics are only relevant if their concentration in water is much higher than the concentration of other organic carbon containing phases (Scenario I, Fig. 4, top). However, at environmental relevant concentrations of microplastics, the effect of natural organic particles likely prevails. If KP is smaller than the LSR, the distribution of the tested substances shifts and almost all compounds would predominantly be available in the freely aqueous phase (Scenario II, Fig. 4, bottom). Thus, our findings for ionizable compounds also support arguments which state that microplastic particles are not substantial vectors for contaminants in terms of substance mass transported due to their low environmental concentrations [20, 26]. In particular, this is true if considered that at very low, but environmental relevant concentration, e.g., for phenanthrene, field-measured Kd values for partitioning to suspended sediment particles lead to much larger KOC values [33] than estimated from the EPISuite database due to non-linear sorption. Thus, the particles’ sorption capacity may be even larger as assumed in our model calculations. Even though particle properties and sorption interactions may change under environmental conditions in particular due to aging [17], studying sorption to rather pristine particles is highly relevant, since the alteration through aging can only be investigated if sorption processes to pristine particles are known.
Equilibrium distribution map for a freshwater system with natural particles (organic carbon) and microplastic particles under two different concentration scenarios. Experimental conditions (plastic LSR = 103 L kg−1, Scenario I) are shown in the top panel and environmental conditions (plastic LSR = 1010 L kg−1, Scenario II) in the bottom panel. Crosses, circles, and pluses show the aqueous equilibrium concentrations at pH 4, pH 7, and pH 10, respectively, in µg L−1 calculated with the experimentally determined DP for PE (black symbols) and for PS (red symbols) and the investigated substances. For both cases, a constant concentration of 10−5 kg L−1 OC was assumed. KOC values were estimated using EPISuite 4.1
Conclusion and outlook
To assess the potential effects of microplastics and associated contaminants on ecosystems it is important to properly evaluate the particle–pollutant interactions, especially since this determines their bioavailability which is yet not well understood. Hydro- and geochemical parameters as well as contact with biota may change particle characteristics, e.g., their surface charge and texture, and may procure aggregation [22, 38]. Thus, it is essential to analyze whether sorption interactions occur which are going beyond mere partitioning as investigated here. At least for pristine plastic particles, we could show that partitioning is still the main sorption mechanism and sorption of charged species at least with the current environmental microplastic concentrations in freshwaters is irrelevant.
References
Alexander M (2000) Aging, bioavailability, and overestimation of risk from environmental pollutants. Environ Sci Technol 34(20):4259–4265
Barber LB, Murphy SF, Verplanck PL, Sandstrom MW, Taylor HE, Furlong ET (2006) Chemical loading into surface water along a hydrological, biogeochemical, and land use gradient: a holistic watershed approach. Environ Sci Technol 40(2):475–486
Barnes DKA, Galgani F, Thompson RC, Barlaz M (2009) Accumulation and fragmentation of plastic debris in global environments. Philos Trans R Soc of Lond B Biol Sci 364(1526):1985–1998
Beckingham B, Ghosh U (2017) Differential bioavailability of polychlorinated biphenyls associated with environmental particles: microplastic in comparison to wood, coal and biochar. Environ Pollut 220(Part A):150–158
Bundschuh M, Weyers A, Ebeling M, Elsaesser D, Schulz R (2016) Narrow pH range of surface water bodies receiving pesticide input in Europe. Bull Environ Contam Toxicol 96(1):3–8
Diamond ML, de Wit CA, Molander S, Scheringer M, Backhaus T, Lohmann R, Arvidsson R, Bergman Å, Hauschild M, Holoubek I, Persson L, Suzuki N, Vighi M, Zetzsch C (2015) Exploring the planetary boundary for chemical pollution. Environ Int 78:8–15
Dolzonek J, Cho CW, Stepnowski P, Markiewicz M, Thoming J, Stolte S (2017) Membrane partitioning of ionic liquid cations, anions and ion pairs—estimating the bioconcentration potential of organic ions. Environ Pollut 228:378–389
Endo S, Takizawa R, Okuda K, Takada H, Chiba K, Kanehiro H, Ogi H, Yamashita R, Date T (2005) Concentration of polychlorinated biphenyls (PCBs) in beached resin pellets: variability among individual particles and regional differences. Mar Pollut Bull 50(10):1103–1114
Escher BI, Schwarzenbach RP, Westall JC (2000) Evaluation of liposome–water partitioning of organic acids and bases. 2. Comparison of experimental determination methods. Environ Sci Technol 34(18):3962–3968
Forbes TL, Forbes VE, Giessing A, Hansen R, Kure LK (1998) Relative role of pore water versus ingested sediment in bioavailability of organic contaminants in marine sediments. Environ Toxicol Chem 17(12):2453–2462
Fu W, Franco A, Trapp S (2009) Methods for estimating the bioconcentration factor of ionizable organic chemicals. Environ Toxicol Chem 28(7):1372–1379
Gasperi J, Garnaud S, Rocher V, Moilleron R (2008) Priority pollutants in wastewater and combined sewer overflow. Sci Total Environ 407(1):263–272
Gavrilescu M, Demnerová K, Aamand J, Agathos S, Fava F (2015) Emerging pollutants in the environment: present and future challenges in biomonitoring, ecological risks and bioremediation. New Biotechnol 32(1):147–156
Goss KU, Bittermann K, Henneberger L, Linden L (2018) Equilibrium biopartitioning of organic anions—a case study for humans and fish. Chemosphere 199:174–181
Horton AA, Svendsen C, Williams RJ, Spurgeon DJ, Lahive E (2017) Large microplastic particles in sediments of tributaries of the River Thames, UK—abundance, sources and methods for effective quantification. Mar Pollut Bull 114(1):218–226
Hüffer T, Hofmann T (2016) Sorption of non-polar organic compounds by micro-sized plastic particles in aqueous solution. Environ Pollut 214:194–201
Jahnke A, Arp HPH, Escher BI, Gewert B, Gorokhova E, Kühnel D, Ogonowski M, Potthoff A, Rummel C, Schmitt-Jansen M, Toorman E, MacLeod M (2017) Reducing uncertainty and confronting ignorance about the possible impacts of weathering plastic in the marine environment. Environm Sci Technol Lett 4(3):85–90
Kan AT, Tomson MB (1996) UNIFAC prediction of aqueous and nonaqueous solubilities of chemicals with environmental interest. Environ Sci Technol 30(4):1369–1376
Karlsson MV, Carter LJ, Agatz A, Boxall ABA (2017) Novel approach for characterizing pH-dependent uptake of ionizable chemicals in aquatic organisms. Environ Sci Technol 51(12):6965–6971
Koelmans AA, Bakir A, Burton GA, Janssen CR (2016) Microplastic as a vector for chemicals in the aquatic environment: critical review and model-supported reinterpretation of empirical studies. Environ Sci Technol 50(7):3315–3326
Lee H, Shim WJ, Kwon J-H (2014) Sorption capacity of plastic debris for hydrophobic organic chemicals. Sci Total Environ 470–471:1545–1552
Li S, Liu H, Gao R, Abdurahman A, Dai J, Zeng F (2018) Aggregation kinetics of microplastics in aquatic environment: complex roles of electrolytes, pH, and natural organic matter. Environ Pollut 237:126–132
Li Z, Sobek A, Radke M (2016) Fate of pharmaceuticals and their transformation products in four small European rivers receiving treated wastewater. Environ Sci Technol 50(11):5614–5621
Liu L, Wu F, Haderlein S, Grathwohl P (2013) Determination of the subcooled liquid solubilities of PAHs in partitioning batch experiments. Geosci Front 4(1):123–126
Llorca M, Schirinzi G, Martinez M, Barcelo D, Farre M (2018) Adsorption of perfluoroalkyl substances on microplastics under environmental conditions. Environ Pollut 235:680–691
Lohmann R (2017) Microplastics are not important for the cycling and bioaccumulation of organic pollutants in the oceans—but should microplastics be considered POPs themselves? Integr Environ Assess Manage 13(3):460–465
Mani T, Hauk A, Walter U, Burkhardt-Holm P (2015) Microplastics profile along the Rhine river. Sci Rep 5:17988
Mintenig SM, Int-Veen I, Löder MGJ, Primpke S, Gerdts G (2017) Identification of microplastic in effluents of waste water treatment plants using focal plane array-based micro-Fourier-transform infrared imaging. Water Res 108:365–372
Murphy F, Ewins C, Carbonnier F, Quinn B (2016) Wastewater treatment works (WwTW) as a source of microplastics in the aquatic environment. Environ Sci Technol 50(11):5800–5808
O’Connor IA, Golsteijn L, Hendriks AJ (2016) Review of the partitioning of chemicals into different plastics: consequences for the risk assessment of marine plastic debris. Mar Pollut Bull 113(1–2):17–24
Pascall MA, Zabik ME, Zabik MJ, Hernandez RJ (2005) Uptake of polychlorinated biphenyls (PCBs) from an aqueous medium by polyethylene, polyvinyl chloride, and polystyrene films. J Agric Food Chem 53(1):164–169
Rockstrom J, Steffen W, Noone K, Persson A, Chapin FS, Lambin EF, Lenton TM, Scheffer M, Folke C, Schellnhuber HJ, Nykvist B, de Wit CA, Hughes T, van der Leeuw S, Rodhe H, Sorlin S, Snyder PK, Costanza R, Svedin U, Falkenmark M, Karlberg L, Corell RW, Fabry VJ, Hansen J, Walker B, Liverman D, Richardson K, Crutzen P, Foley JA (2009) A safe operating space for humanity. Nature 461(7263):472–475
Rügner H, Schwientek M, Beckingham B, Kuch B, Grathwohl P (2013) Turbidity as a proxy for total suspended solids (TSS) and particle-facilitated pollutant transport in catchments. Environ Earth Sci 69(2):373–380
Schmidt C, Krauth T, Wagner S (2017) Export of plastic debris by rivers into the sea. Environ Sci Technol 51:12246–12253
Schwarzenbach RP, Escher BI, Fenner K, Hofstetter TB, Johnson CA, von Gunten U, Wehrli B (2006) The challenge of micropollutants in aquatic systems. Science 313(5790):1072–1077
Seidensticker S, Zarfl C, Cirpka OA, Fellenberg G, Grathwohl P (2017) Shift in mass transfer of wastewater contaminants from microplastics in the presence of dissolved substances. Environ Sci Technol 51(21):12254–12263
Wang F, Shih KM, Li XY (2015) The partition behavior of perfluorooctanesulfonate (PFOS) and perfluorooctanesulfonamide (FOSA) on microplastics. Chemosphere 119:841–847
Wang J, Tan Z, Peng J, Qiu Q, Li M (2016) The behaviors of microplastics in the marine environment. Mar Environ Res 113:7–17
Wang W, Wang J (2018) Comparative evaluation of sorption kinetics and isotherms of pyrene onto microplastics. Chemosphere 193:567–573
Wojslawski J, Bialk-Bielinska A, Paszkiewicz M, Tonski M, Stepnowski P, Dolzonek J (2018) Evaluation of the sorption mechanism of ionic liquids onto multi-walled carbon nanotubes. Chemosphere 190:280–286
Yokota K, Waterfield H, Hastings C, Davidson E, Kwietniewski E, Wells B (2017) Finding the missing piece of the aquatic plastic pollution puzzle: interaction between primary producers and microplastics. Limnol Oceanogr Lett 2(4):91–104
Authors’ contributions
The study was designed by SS, PG, and CZ. The experiments were planned and performed by SS and JL. The modeling was performed by SS, PG, and CZ. The manuscript was written by SS, PG, and CZ. All authors read and approved the final manuscript.
Acknowledgements
We would like to thank Renate Seelig and Thomas Wendel for their support with the experiments. The study was supported by a grant from the Deutsche Forschungsgemeinschaft (DFG) under grant agreement GR 971/31-1. Furthermore, we would like to thank two anonymous reviewers for the helpful comments and valuable remarks.
Competing interests
The authors declare that they have no competing interests.
Availability of data and materials
Materials and data are either described in the main manuscript or in the additional file. MATLAB codes are available on request.
Consent for publication
Not applicable.
Ethics approval and consent to participate
Not applicable.
Funding
This study was funded by a grant from the Deutsche Forschungsgemeinschaft (DFG) under Grant agreement GR 971/31-1.
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Author information
Authors and Affiliations
Corresponding authors
Additional file
Additional file 1.
Additional tables and figures.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Seidensticker, S., Grathwohl, P., Lamprecht, J. et al. A combined experimental and modeling study to evaluate pH-dependent sorption of polar and non-polar compounds to polyethylene and polystyrene microplastics. Environ Sci Eur 30, 30 (2018). https://doi.org/10.1186/s12302-018-0155-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s12302-018-0155-z