Abstract
Double-gate tunnel field-effect transistor (DG TFET) is expected to extend the limitations of leakage current and subthreshold slope. However, it also suffers from the ambipolar behavior with the symmetrical source/drain architecture. To overcome the ambipolar current, asymmetry must be introduced between the source and drain. In this paper, we investigate the performances of DG TFET with step channel thickness (SC TFET) by utilizing the 2D simulation. The asymmetry between source and drain is introduced through the step channel thickness; hence, the ambipolar behavior is expected to be relieved. The results show that the SC TFET exhibits significant reduction of ambipolar current compared with the conventional DG TFET. The mechanisms of SC TFET are thoroughly discussed to explore the physical insight. The impacts introduced by the structure parameters on onset voltage, subthreshold slope, drain current in on-state and ambipolar-state are also exhibited in determining the optimal structure.
Avoid common mistakes on your manuscript.
Background
As the extreme scaling process continues, CMOS technology with conventional MOSFET encounters various challenges such as the increasing leakage current and subthreshold slope (SS). Tunnel field-effect transistor (TFET), which utilizes the band-to-band tunneling (BTBT) mechanisms, is expected to extend the limitations of leakage current and SS [1,2,3,4,5,6,7,8]. Silicon-based TFET shows advantages such as high reliability and low cost. However, conventional silicon-based TFET exhibits a relatively low on-current in comparison with the MOSFET due to the constrained BTBT rate [9,10,11]. To develop the potential of silicon-based TFET, various novel TFET structures have been recently proposed to enhance the on-state current. The double-gate TFET (DG TFET) shows improved BTBT rate, leading to the enhanced on-current [12,13,14]. However, the ambipolar current of DG TFET is also increased since the BTBT rate improvement is activated in the ambipolar state as well [15]. To further overcome the ambipolar current, asymmetry must be introduced between source and drain [16]. DG TFETs with gate-drain underlap and less drain doping concentration are common methods to relieve the ambipolar problem [17,18,19]. But the gate-drain underlap requires greater S/D distance and less drain doping concentration increases the series resistances [15]. A previous work has shown that the ambipolar effects in the TFET with drain underlap could be further relieved by using the low-k spacers and by placing the contacts in the top and bottom configuration [15], suggesting that combined asymmetry strategies could be meaningful in improving the performance of the TFET. In our previous work, the FinFET with asymmetry fin width has been demonstrated to improve the performance of FinFET [20]. It is also believed that the channel thickness tsi has a significant impact on the BTBT rate of DG TFET [21]; hence, the asymmetry between the source thickness and the drain thickness might further relieve the ambipolar current and need to be studied thoroughly.
In this paper, we investigate the various performances of DG TFET with step channel thickness (SC TFET), the asymmetry between the source and drain is introduced through the step channel thickness so that the ambipolar current is expected to be reduced. The rest of this paper is arranged as follows: Section 2 presents the device structure and simulation setup. In Section 3, the mechanisms of the SC TFET is thoroughly discussed. The detailed discussion regarding the impacts of structure parameters on the transfer curves, onset voltage (Vonset), average SS and drain current in on/ambipolar-state is also presented. Finally, the findings of this paper are enlightened in section IV.
Structure and Simulation
The schematic diagram of the SC TFET considered in this paper is shown in Fig. 1a. The channel thickness near the source region is not equal to the channel thickness near the drain region. The channel thickness changes stepwise at a certain point in the channel region. The step height and the step position are denoted as H and Ls respectively. tsi1 and tsi2 are the channel thickness near the source region and the drain region respectively. The effective oxide thickness (EOT) is 1 nm in our simulation. The source region is highly p-doped (1020 atoms/cm3) and the drain region is highly n-doped (1020 atoms/cm3) to reduce the series resistance [15], the channel region is lightly n-doped (1017 atoms/cm3). In order to analysis the onset voltage with various channel thickness setups, the work function of metal gate is fixed to 4.5 eV, the gate length is equal to the channel length Lch and set to 50 nm [22,23,24,25]. The simulations are carried out using Sentaurus TCAD release I-2013.12 [26, 27]. The doping dependence model and the field dependent mobility model are Philips unified mobility model and Lombardi mobility model, respectively. The Fermi–Dirac statistics, Shockley–Read–Hall and Auger recombination model are also utilized. In order to account for the highly doped source/drain regions, the band gap narrowing model is activated. The nonlocal BTBT model based on Wentzel–Kramer–Brillouin (WKB) approximation tuned with the experimental results of [28] and the density-gradient quantization model are enabled to achieve the accurate simulation [29, 30]. The onset voltage is defined as the gate voltage at which the subthreshold slope is maximum. The average SS is extracted from the off-state current to Id = 10−11 A/μm.
Results and Discussion
Transfer Curves and Mechanism
Figure 1b shows the transfer curves of SC TFET and conventional DG TFET in log and linear scale, respectively. We mark out the on-state, off-state, and ambipolar-state in Fig. 1b. For TFETs, a higher current of on-state and a lower current of ambipolar-state are always desired, which requires that the Vonset and SS should be low while the off-state should have a wide voltage range. As shown in Fig. 1b, the Vonset of conventional DG TFET with channel thickness of 10 nm are lower than that of the DG TFET with channel thickness of 20 nm. The extracted Vonset of DG TFET with tsi = 10 nm is 0.04 V and its extracted average SS is 44.8 mV/dec, the Vonset and the average SS of conventional DG TFET with tsi = 20 nm is 0.1 V and 50.6 mV/dec, respectively. The drain current of conventional DG TFET with tsi = 10 nm is improved by 94.7% compared to the conventional DG TFET with tsi = 20 nm. The main reason of this drain current improvement is the reduced SS and Vonset. However, the off-state range of the conventional DG TFET with tsi = 10 nm is only 0.17 V. The conventional DG TFET with tsi = 20 nm, in comparison, exhibits off-state range of 0.45 V. As a result, the ambipolar-state current of the conventional DG TFET with tsi = 20 nm is reduced by 3 orders of magnitude compared to the conventional DG TFET with tsi = 10 nm.
For the fair comparison, the tsi1 and tsi2 of SC TFETs are equal to the channel thicknesses of above conventional DG TFETs, respectively. The narrower channel thickness tsi1 of SC TFET is 10 nm and the wider channel thickness tsi2 of SC TFET is 20 nm. The position of step is assumed at the middle of the channel and the Ls is 25 nm. One can observe that the SC TFET shows promising characteristics including the high drain current in the on-state as well as the wide range off-state. The drain current of SC TFET in the on-state is similar compared to the conventional DG TFET with tsi = 10 nm, the average SS is 45.8 mV/dec and the Vonset is 0.03 V. However, the off-state range of SC TFET is improved up to 123.5% and the ambipolar-state current is also reduced by 3 orders of magnitude in comparison with the conventional DG TFET with tsi = 10 nm. As a result, the on-state characteristics of SC TFET is similar to the conventional DG TFET with narrow channel thickness, the SC TFET also shows nearly parallel off/ambipolar curves to the conventional DG TFET with wide channel thickness. Hence, the SC TFET can achieve low SS, reduced Vonset, and wide off-state range simultaneously.
To explore the physical mechanism of the SC TFET, we compare the BTBT rates and energy band diagrams in the on-state, near onset point and ambipolar-state, respectively. Figure 2a shows the BTBT rates of the SC TFET and the conventional DG TFETs. It can be seen that the BTBT rate strongly depends on the channel thickness. In fact, the relationship between the channel thickness and the BTBT current IBTBT can be expressed as [31].
Where λ = (εsitsitox/2εox)1/2 is the natural length, εsi and εox are the silicon and oxide permittivity respectively and tox is the oxide thickness. ΔΦ is the energy range over which tunneling can take place, Eg is the band gap at the tunnel junction, and m* is the tunneling mass. Equation (1) indicates that the IBTBT should increases as tsi reduces. Therefore, the BTBT rate of conventional DG TFET with tsi = 10 nm should greater than that of the conventional DG TFET with tsi = 20 nm. The SC TFET shows similar distribution of BTBT rate to the conventional DG TFET with tsi = 10 nm. This is because that the BTBT mainly occurs near the source junction in the on-state, hence the channel thickness near the source junction will determine the on-state BTBT rate. Figure 2b shows the energy band diagram of the SC TFET and the conventional DG TFETs. Since the BTBT rate is fundamentally related to the tunneling distance, the energy band diagram, which can present the tunneling distance clearly, will explain the origin of BTBT rates variation. In Fig. 2b, the minimum tunneling distance of the SC TFET is located near the source junction and is more or less equal to that of the conventional DG TFET with tsi = 10 nm. The minimum tunneling distance of conventional DG TFET with tsi = 20 nm is significantly wider; hence, its BTBT rate is reduced compared to the SC TFET and the conventional DG TFET with thinner channel thickness.
Figure 3a shows the BTBT rates when the gate voltage is zero and is close to the onset voltage. It can be seen that the SC TFET owns the highest BTBT rate, followed by the conventional DG TFET with tsi = 10 nm. The conventional DG TFET with tsi = 20 nm shows the lowest BTBT rate. Figure 3b exhibits the corresponding energy band diagram. One can observe that the location of minimum distance from the valence band to the conduction band is at the center of channel region. Besides, the minimum distance of the conventional DG TFET with wider channel thickness is longer than that of the SC TFET and conventional DG TFET with thinner channel thickness. It indicates that the channel thickness also has a significant impact on the BTBT rate at the onset point. Hence, the Vonset is dependent on the channel thickness as well. Another fact is that the SC TFET exhibits greater BTBT rate than that of the conventional DG TFET with tsi = 10 nm even though their minimum channel thicknesses are equal. This phenomenon is attributed to the variation of potential distribution introduced by the corner of gate electrode, as can be also observed in other work [32, 33]. As a result, the SC TFET shows the lowest Vonset, followed by the conventional DG TFET with thin channel thickness, and the conventional DG TFET with wide channel thickness exhibits the highest Vonset.
Figure 4a shows the comparison of BTBT rates in the ambipolar-state. Since the BTBT rate is strongly dependent on the channel thickness, the conventional TFET with tsi = 10 nm shows the most significant BTBT rate compared to the other two TFET structures. The SC TFET, however, shows the similar BTBT rate to the conventional DG TFET with tsi = 20 nm. It is because that the tunneling is mainly generated near the drain region and the SC TFET has wider channel thickness near the drain region. In Fig. 4b, the energy band diagram in the ambipolar-state is also exhibited. It can be clearly seen that the minimum tunneling distance is located near the drain region. Besides, the tunneling distances of SC TFET and conventional DG TFET with wider channel thickness are greater than that of the conventional DG TFET with thinner channel thickness, resulting in the low ambipolar current of SC TFET and conventional DG TFET with wider channel thickness.
Impacts of H and LS on DC Characteristics
Figure 5a shows the transfer curves of the SC TFET with various H and tsi1 = 10 nm. It can be seen that the H has less impact on the on-state current. The ambipolar current, however, reduces significantly as the H increases, the off-state range improves with the rise of H as well. It can be also seen that the reduction of the ambipolar current decreases as the H increases. The reason for this is that the coupling effect of the double-gate structure tends to be less significant with a larger channel thickness [31]. Therefore, as the H increases, the BTBT rates become more independent of the channel thickness, leading to the saturation of ambipolar current. To further explore the optimal structure parameter, the effects of H varies from 0 to 15 nm on the device performances are extracted and shown in Fig. 5b–d. Figure 5b exhibits the Vonset and the BTBT rate variation with different H and tsi1. It can be seen that the Vonset decreases monotonically with the increase of H. This is because that the corner of gate electrode would introduce the variation of the potential distribution in the channel region [32, 33], resulting in the alteration of the BTBT rate and the Vonset. Figure 5b demonstrates that the BTBT rate increases as the H improves. As a result, the decreased Vonset can be found with the increased H. One can also observe that Vonset increases as the tsi1 increases. The main reason is that the increased tsi1 weakens the BTBT rate, resulting in a higher Vonset. In Fig. 5c, the extracted average SS of SC TFET with various H and tsi1 is shown. The trend of the SS with different H is opposite to that of the Vonset. In another word, the SS rises as the H increases. We have mentioned that the on-state drain current is dependent on the tsi1, so that the SC TFETs with different H but with the same tsi1 should have the similar drain current in the on-state. Besides, it is also known that the Vonset decreases with the increase of H. This implies that the range of gate voltage to drive the same drain current is improved as the H increases. As a result, the average SS increases monotonically with the rise of H. It can be also seen that the increase of tsi1 will undermine the SS, which is due to the reduced gate control capability. Figure 5d shows the drain current in the on-state and ambipolar-state with different H and tsi1, respectively. The on-state current is nearly independent on the H, but it is greatly affected by the tsi1, which corresponds to our previous result that the on-state tunneling mainly occurs near the source region and is strongly dependent on the channel thickness near the source region. The ambipolar current, however, reduces as the H increases. Since the ambipolar-state tunneling is dominated near the drain region, the increase of H will improve the channel thickness at the drain side and thus weakens the ambipolar current. It can be also seen that the ambipolar current drops more significantly when the H is less than 10 nm, which is due to the greater coupling effect with thinner channel thickness.
In Fig. 6a, the transfer curves of SC TFET with different Ls are presented respectively. Ls = 0 nm represents the conventional DG TFET with corresponding tsi2 and Ls = 50 nm represents the conventional DG TFET with corresponding tsi1. It can be seen that the location of step has a significant impact on the ambipolar current and the off-state range. The SC TFETs with Ls less than 30 nm show similar ambipolar current and off-state range. As the Ls exceeds 30 nm, the ambipolar current is greatly enhanced. Fig. 6b shows the Vonset and the BTBT rate variation with various Ls and tsi1, the trend that the Vonset increases as the tsi1 improves can be clearly observed as well. The change inflection point on the Ls = 10 nm is a result of the variety of the tsi1. Since Ls = 0 nm is the conventional DG TFET with a larger channel thickness, the BTBT rate would reduce, leading to an increased Vonset and a decreased on-state current. Barring the case of conventional DG TFET, the Vonset of SC TFET is increased monotonically as the Ls rises, which is due to the reduced BTBT rate induced by the step channel structure. Figure 6c exhibits the impacts of the Ls and tsi1 on the SS of SC TFETs. The increased tsi1 results in the degraded SS. According to Eq. (1), a raised channel thickness would lower the coupling effects between the gate electrodes, leading to a reduced gate control capability and an increased SS [12]. As the Ls drops, the region with greater channel thickness will expand and would weaken the overall gate control capability. As a result, a reduced Ls will undermine the SS of SC TFETs, which can be clearly observed in Fig. 6c. Figure 6d presents the drain current in the on-state and ambipolar-state with different Ls and tsi1, respectively. One can observe that the on-state current of SC TFET is more or less equal to the conventional DG TFET with corresponding tsi1. As for the ambipolar current, the SC TFETs with Ls less than 30 nm show the similar current to the conventional DG TFETs with corresponding tsi2. When the Ls increases to 40 nm, the ambipolar current rises dramatically. In fact, for the case of SC TFET with Ls = 40 nm and tsi1 = 20 nm, its ambipolar current is even greater than that of the conventional DG TFET with tsi1 = 20 nm. This is because that the vertical part of gate electrode can enhance the tunneling area especially when the vertical part of gate electrode is close to the PN junction [34]. It indicates that the Ls should be less than 40 nm for the purpose of reducing ambipolar current.
To determine the optimal structure parameters of the SC TFET, an orthogonal simulation is conducted by studying the combined effect of the H and the Ls on the device performance. The tsi1 is fixed at 10 nm to achieve a greater on-state current. In Fig. 7a, the ambipolar current is extracted as a function of the Ls with various H. It can be clearly seen that the ambipolar current reduces significantly as the H decreases, which suggests that a higher H is promising in terms of achieving a lower ambipolar current. However, one can observe that the benefit from a greater H is less significant. Therefore, a H = 15 nm would be the optimal value considering that a larger H could only increase the device area. Meanwhile, a decreased Ls will also lower the ambipolar current especially with a greater H. Hence, a lower Ls is desired for the purpose of minimal ambipolar current. Nevertheless, a lower Ls could also lead to an increase of the subthreshold slope, as can be observed in Fig. 7b. The subthreshold slope increases slowly with a higher Ls but rises rapidly with a lower Ls, indicating that a Ls about 25 nm would be the compromise value. As a result, the optimal device parameters would be H = 15 nm and Ls = 25 nm where both the ambipolar current and the subthreshold slope are relatively low.
Fabrication Method
A feasible fabrication process of the SC TFET is exhibited in Fig. 8. Due to the unique shape of channel, the step channel thickness can be achieved more easily by adopting the vertical structure. The process begins by preparing the silicon substrate with SiN and photoresist deposition, as shown in Fig. 8a. In Fig. 8b, the SiN patterning is achieved by lithography, following by the etching to form the channel region, then the N+ region is introduced by a vertical As implantation and annealing [35]. After that, the isolation oxide is deposited to prevent the drain region from etching in the following process, as shown in Fig. 8c. In Fig. 8d, the ashing and trimming are adopted by utilizing the reaction ion etching [36] to reduce the thickness and width of SiN. The step channel thickness is then introduced by etching, as shown in Fig. 8e. The remain processes are similar to the conventional vertical TFET, involving gate oxide forming, gate deposition, silicon exposure, and source region implantation [35, 37], as shown in Fig. 8f.
Conclusion
We investigate the electrical performances of DG TFET with step channel thickness (SC TFET) by utilizing the 2D simulation. The asymmetry between the source and drain is introduced through the step channel thickness; hence, the ambipolar behavior is significantly relieved. The SC TFET exhibits similar on-state characteristics of the conventional DG TFET with corresponding tsi1 and parallel off/ambipolar curves of the conventional DG TFET with corresponding tsi2. As a result, the SC TFET can achieve wide off-state range, low ambipolar current, and maintain the low SS simultaneously. The mechanisms of SC TFET are thoroughly discussed to explore the physical insight. The impacts introduced by the structure parameters on onset voltage, subthreshold slope, drain current in on-state, and ambipolar-state are also studied to determine the optimal structure. The SC TFET with H of 15 nm and Ls of 25 nm shows the optimal performances. Moreover, the architecture of step channel thickness provides an alternative asymmetry method. Since the combined asymmetry strategies are proved to be effective, our work could further provide performance improvement of the TFET.
Availability of Data and Materials
All data are fully available without restriction.
Abbreviations
- DG TFET:
-
Double-gate tunnel field-effect transistor
- SC TFET:
-
DG TFET with step channel thickness
- SS :
-
Subthreshold slope
- BTBT:
-
Band-to-band tunneling
- EOT:
-
Effective oxide thickness
- V onset :
-
Onset voltage
- H :
-
Step height
- L s :
-
Step position
- L ch :
-
Channel length
- t si :
-
Channel thickness
- t si1 :
-
Channel thickness near the source region
- t si2 :
-
Channel thickness near the drain region
References
Avci U E, Rios R, Kuhn K, and Young I A. Comparison of performance, switching energy and process variations for the TFET and MOSFET in logic. VLSI Symp Tech Dig. 2011;124-125.
Huang Q, Huang R, Zhan Z, et al. A novel Si tunnel FET with 36mV/dec subthreshold slope based on junction depleted-modulation through striped gate configuration. IEEE Int. Electron Devices Meeting (IEDM). 2012;8.5. 1-8.5. 4.
Chen S, Liu H, Wang S et al (2018) Analog/RF performance of T-shape gate dual-source tunnel field-effect transistor. Nanoscale Res Lett 13:321
Li W, Liu H, Wang S et al (2017) Design of high performance Si/SiGe heterojunction tunneling FETs with a T-shaped gate. Nanoscale Res Lett 12:198
Wu C, Huang Q, Zhao Y et al (2016) A novel tunnel FET design with stacked source configuration for average subthreshold swing reduction. IEEE Trans Electron Devices 63:5072–5076
Feng G, Zhao Y, Jiang J (2019) Lightweight flexible indium-free oxide TFTs with AND logic function employing chitosan biopolymer as self-supporting layer. Solid State Electron 153:16–22
Qin T, Liao C, Huang S et al (2017) Analytical drain current model for symmetric dual-gate amorphous indium gallium zinc oxide thin-film transistors. Jpn J Appl Phys 57(1):014301
Hu M, Yang Z, Zhou W et al (2018) Field effect transistors based on phosphorene nanoribbon with selective edge-adsorption: a first-principles study. Physica E: Low-dimensional Systems and Nanostructures 98:60–65
Avci U E, Rios R, Kuhn K J, et al. Comparison of power and performance for the TFET and MOSFET and considerations for P-TFET. IEEE International Conference on Nanotechnology. 2011;869-872.
Koswatta SO, Lundstrom MS, Nikonov DE (2009) Performance comparison between pin tunneling transistors and conventional MOSFETs. IEEE Trans. Electron Devices 56:456–465
Avci U E, Morris D H, Hasan S, et al. Energy efficiency comparison of nanowire heterojunction TFET and Si MOSFET at Lg= 13nm, including P-TFET and variation considerations. IEEE Int. Electron Devices Meeting (IEDM). 2013;33.4.1-33.4.4.
Boucart K, Ionescu AM (2007) Double-gate tunnel FET with high-k gate dielectric. IEEE Trans. Electron Devices 54:1725–1733
Boucart K, Ionescu AM (2007) Length scaling of the double gate tunnel FET with a high-k gate dielectric. Solid State Electron 51:1500–1507
Bardon MG, Neves HP, Puers R et al (2010) Pseudo-two-dimensional model for double-gate tunnel FETs considering the junctions depletion regions. IEEE Trans. Electron Devices 57:827–834
Vladimirescu A, Amara A, Anghel C (2012) An analysis on the ambipolar current in Si double-gate tunnel FETs. Solid State Electron 70:67–72
Krishnamohan T, Kim D, Raghunathan S et al (2008) Double-gate strained-Ge heterostructure tunnelling FET (TFET) with record high drive current and < 60 mV/dec subthreshold slope. IEDM Tech Dig:947–949
Lee JS, Seo JH, Cho S et al (2013) Simulation study on effect of drain underlap in gate-all-around tunneling field-effect transistors. Curr. Appl. Phys. 13:1143–1149
Anghel C, Gupta A, Amara A et al (2011) 30-nm tunnel FET with improved performance and reduced ambipolar current. IEEE Trans Electron Devices 58:1649–1654
Wu J, Taur Y (2016) Reduction of TFET off-current and subthreshold swing by lightly doped drain. IEEE Trans Electron Devices 63:3342–3345
Zhang M, Guo Y, Chen J et al (2019) Simulation investigation of the diffusion enhancement effects in FinFET with graded fin width. IEEE Trans Nanotechnol 18:700–703
Toh EH, Wang GH, Samudra G et al (2007) Device physics and design of double-gate tunneling field-effect transistor by silicon film thickness optimization. Appl Phys Lett 90:263507
Kim J, Oh H, Kim J et al (2017) Electrical characteristics of tunneling field-effect transistors with asymmetric channel thickness. Jpn J Appl Phys 56:024201
Mallik A, Chattopadhyay A (2011) Drain-dependence of tunnel field-effect transistor characteristics: the role of the channel. IEEE Trans Electron Devices 58:4250–4257
Padilla JL, Gamiz F, Godoy A (2012) A simple approach to quantum confinement in tunneling field-effect transistors. IEEE Electron Device Lett 33:1342–1344
Sahay S, Kumar MJ (2017) Physical insights into the nature of gate-induced drain leakage in ultrashort channel nanowire FETs. IEEE Trans. Electron Devices 64:2604–2610
Synopsys, Mountain View, CA, USA. Sentaurus Device User Guide Version: H-2013.03. 2013.
Villalon A, Le Carval G, Martinie S et al (2014) Further insights in TFET operation. IEEE Trans Electron Devices 61:2893–2898
Hurkx GAM, Klaassen DBM, Knuvers MPG (1992) A new recombination model for device simulation including tunneling. IEEE Trans. Electron Devices 39:331–338
Liu M, Xie Q, Xia S, et al. A novel step-shaped gate tunnel FET with low ambipolar current. Int. Symp. Devices Circuits Syst. (ISDCS). 2019;1-4.
Shin SS, Kim JH, Kim S (2019) L-shaped tunnel FET with stacked gates to suppress the corner effect. Jpn J Appl Phys 58:SDDE10
Knoch J, Appenzeller J. A novel concept for field-effect transistors-the tunneling carbon nanotube FET. 63rd Device Research Conference Digest (IEEE DRC). 2005;1:153-156.
Xiong W, Park J W, Colinge J P. Corner effect in multiple-gate SOI MOSFETs. IEEE Int. SOI Conf. 2003:111-113.
Wang Z, Zhang B, Fu Q et al (2012) An L-shaped trench SOI-LDMOS with vertical and lateral dielectric field enhancement. IEEE electron device letters 33:703–705
Woo S, Kim S (2018) Covered source–channel tunnel field-effect transistors with trench gate structures. IEEE Trans Nanotechnol 18:114–118
Gandhi R, Chen Z, Singh N et al (2011) Vertical si-nanowire n-type tunneling FETs with low subthreshold swing (≤ 50 mv/decade) at room temperature. IEEE Electron Device Lett 32:437–439
Chang L, Choi Y, Ha D et al (2003) Extremely scaled silicon nano-CMOS devices. Proc IEEE 91:1860–1873
Kwong D L, Li X, Sun Y, et al. Vertical silicon nanowire platform for low power electronics and clean energy applications. J Nanotechnol. 2012;2012:492 121-1–492 121-21.
Acknowledgements
We acknowledge the Project of National Natural Science Foundation of China, the Project of China Postdoctoral Science Foundation, the Project of Natural Science Foundation of Colleges in Jiangsu Province, and the Graduate Students Research Innovation Program of Jiangsu Province.
Funding
This research is supported by the National Natural Science Foundation of China (no. 61874059, no.61574081, no.61704084), the China Postdoctoral Science Foundation (no. 2018M642291), the Natural Science Foundation of Colleges in Jiangsu Province (no.17KJB510042), and the Graduate students research innovation program of Jiangsu Province (46106CX18029).
Author information
Authors and Affiliations
Contributions
MZ generated the research idea, carried out the simulation, analyzed the data, and wrote the paper. YG, JZ, JY, and JC participated in the discussion. YG and have given the final approval of the version to be published. All authors read and approved the final manuscript.
Authors’ Information
MZ and JC are Ph.D. students in Nanjing University of Posts and Telecommunications. JZ and JY are doctors in Nanjing University of Posts and Telecommunications. YG is a professor in Nanjing University of Posts and Telecommunications.
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhang, M., Guo, Y., Zhang, J. et al. Simulation Study of the Double-Gate Tunnel Field-Effect Transistor with Step Channel Thickness. Nanoscale Res Lett 15, 128 (2020). https://doi.org/10.1186/s11671-020-03360-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s11671-020-03360-7