Abstract
The effects of various parameters on bromate reduction were tested using lab-scale batch reactors with sulfur based autotrophic and methanol based heterotrophic denitrification processes. The initial bromate (BrO3 –) concentration of 100 and 500 μg/L was completely reduced and bromide (Br-) was produced stoichiometrically from bromate in all batch reactors. In all experiments, nitrate was completely reduced to below detection limit. Kinetic studies showed that the sulfur-based autotrophic nitrate reduction rate increased with increasing initial nitrate concentration. At stoichiometrically sufficient methanol concentration as an external carbon source, nitrate and bromate were reduced to below US EPA drinking water limits in heterotrophic denitrification conditions. The methanol was completely depleted at the end of the heterotrophic operation conditions.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Bromate is a disinfection by-product produced from bromide (Br-) contained in water when ozonation is applied in the drinking water [1]. Bromate is a suspected genotoxic carcinogen and has been shown that it causes renal tumors in rats and mice [2]. A maximum allowed contaminant level of bromate is 10 μg/L by United States Environmental Protection Agency (US EPA). Bromate cannot be removed by traditional water treatment methods such as filtration, chlorination or lime softening [3].
Nitrate has become a problem in many part of the world as well as in Turkey. The US EPA has set the maximum contaminant levels of 10 mg NO3 _N L-1 (nitrate) for drinking water [4]. Reverse osmosis, electrodialysis and ion exchange are the physico-chemical methods used for treatment of nitrate from drinking waters [5, 6]. The main disadvantages of these methods are high operation and maintenance cost, generation of secondary waste brines. As an alternative, biological denitrification, either autotrophic or heterotrophic has been proposed separately for nitrate and/or bromate removal [7, 8].
Sulfur-based autotrophic denitrification is an effective alternative due to low cost and availability of elemental sulfur [9]. It is insoluble and provides a slow release supply of electrons on demand, offering advantages of low maintenance.
In this process, the elemental sulfur acts as an electron donor, and nitrate serves as an electron acceptor. Hence, when nitrate is reduced to nitrogen gas, sulfur is oxidized to sulfate (reaction (1)).
On the other hand, heterotrophic denitrifying bacteria need an organic carbon source for respiration and growth. A wide variety of organic carbon sources have been used such as methanol, ethanol, glucose, acetate etc. If methanol is used as a carbon source, the stoichiometric relationships are written as follows (reaction (2)).
The aim of presented experiment was to evaluate the feasibility of the denitrification concept to the removal of a micropollutant such a bromate (in the μg/L range) from contaminated water, containing nitrate at much higher concentration (in the mg/L range) using batch reactors. The process has monitored for by products and performance of the autotrophic and heterotrophic denitrification processes was investigated in a series of experiments operated under different initial bromate, nitrate and methanol (as an organic carbon source) concentrations.
Methods
Sulfur-based autotrophic batch experiments
The sulfur-based autotrophic denitrification was tested in 150 mL serum bottles at 30°C, filled with medium supplemented with 50 mg/L K2HPO4. The batch reactors were consisted of 3 g sulfur and limestone particles. Batch experiments were carried out in three different nitrate concentrations (25, 50 and 75 mg/L) and two different bromate concentrations (100 and 500 μg/L) (Table 1). Then, the serum bottles were inoculated with the 5 mL (130 ±18 mg VSS/L medium) of denitrifying activated sludge which obtained from the first anoxic tank of a five stage Bardenpho process located in Harran University Campus (Sanliurfa, Turkey).
Methanol-based heterotrophic batch experiments
Similar to autotrophic conditions, the heterotrophic denitrification was tested with same K2HPO4, NO3 -, bromate and biomass concentrations (Table 2). In order to obtain heterotrophic denitrification conditions, methanol was added to the medium at two different concentrations. All the serum bottles were flushed with N2 gas to ensure anoxic conditions. All the serum bottles were sparged with N2 gas for 20 minutes to ensure the removal of dissolved oxygen as Sahinkaya < Dursun [10] reported.
Sampling and analytical techniques
Samples for analysis were collected for the measurement of BrO3 –, Br–, NO3 –, NO2 –, dissolved organic carbon (DOC), sulfate, pH, and alkalinity. All samples were filtered over a 0.45 μ m-pore-size sterile filter. NO3 -, NO2 - and SO4 2- concentrations were determined by ion chromatography (Schimadzu, Prominence HIC-NS, IC-A3 column). BrO3 – and Br– were measured by ion chromotography (DIONEX-ICS 3000 with AS19 column, bromate detection limit of 3 μg/L). DOC was measured by TOC analyzer (TOC VCPH, Shimadzu, Japan).
Results and discussion
Performance of autotrophic denitrification process
In order to examine denitrification performance with initial different nitrate and bromate concentrations, 6 batch tests were performed under autotrophic conditions. In these batch experiments, the elemental sulfur acts as an electron donor and nitrate serves as an electron acceptor (reaction (1)). Hence, when nitrate is reduced to nitrogen gas, sulfur is oxidized to sulfate (reaction (1)).
The batch reactors were operated under autotrophic conditions at two concentrations of bromate (100 and 500 μg/L) and three concentrations of nitrate (25, 50 and 75 mg/L). It was observed that nitrate concentration decreased after inoculation of denitrifiers to the batch reactors. Nitrite was detected as an intermediate and maximum NO2 --N concentration was reached 7.3 ± 3.5 mg/L during bromate and nitrate removal. NO2 --N was decreased rapidly after 100 hrs which indicates that denitrification occurred within the system (Figure 1).
The reduction rates of NO3 --N at various initial NO3 --N and BrO3 – concentrations were studied in batch serum bottles. The results of batch assays were summarized at Table 3. The theoretical sulfate productions calculated according to reaction (1) assuming complete denitrification were 189, 377 and 578 mg/L for 25, 50 and 75 mg/L nitrate respectively. The measured sulfate production was higher than the theoretically calculated values, which should be due to the input of oxygen during sampling.
Although sulfur-based autotrophic denitrification has several advantages, its main disadvantages are sulfate and acid formation. It is found that sulfate formation was increased as a result of sulfur oxidizing autotrophic denitrification during the experiment (Table 3 and Figures 1 and 2). The concentration of sulfate in autotrophic batch reactor was higher than sulfate limit value of 250 mg/L, set by US EPA.
Figure 2 shows nitrate depletion and sulfate production with time using 500 μg/L bromate and nitrate at three different dosages (25, 50 and 75 mg/L NO3 --N). The measured maximum NO2 --N concentrations were 2.3 ± 1.1, 4.9 ± 2.1 and 5.0 ± 2.3 mg/L, respectively (Table 3). Also, produced sulfate concentrations were determined 372, 458 and 749 mg/L in batch reactors for nitrate concentrations of 25, 50 and 75 mg/L respectively. In this study, nitrate reduction rate increased with increasing initial nitrate concentration with transient nitrite accumulation. Similar finding was also reported by Hijnen et al. [11].
The nitrite accumulation was only transient and complete nitrate denitrification and bromate removal was observed at autotrophic batch experiment. The results of study showed that the bromate removal via autotrophic denitrification process was not effected increasing initial bromate concentrations from 100 to 500 μg/L. Throughout the experiment, decreasing bromate simultaneously with a stoichiometric increase in bromide was observed at the steady state conditions (Figures 3 and 4).
Similar to this study, Krisits et al. [8] reported that nitrate reduction rate was faster than bromate. Matos et al. [12] noted that bromate reduction is thermodynamically less favorable (it releases less energy) compared to nitrate. Additionally, they observed that increasing initial bromate concentration (from 200 μg/L to 20.48 mg/L) inhibit biological denitrification. The results showed that denitrification rate was relatively lower when increased initial bromate concentration in this study (Table 3). However, complete nitrate and bromate reduction were occurred at the end of the experiments.
Performance of heterotrophic denitrification process
Heterotrophic denitrifying bacteria use organic compounds as carbon and energy source. The organic compounds are required for complete denitrification depends on the nitrate concentration and bacteria yield coefficient. The nitrite accumulates in water when added organic is stoichiometrically insufficient [6, 13]. On the other hand, the residual organic compound remains in the treated water when the added organic is excessive [13].
The C:N ratio is an important factor effecting the performance of heterotrophic denitrification process [14]. Liu et al. [15] reported that stoichiometrically C:N (mg CH3OH: NO3 --N) ratio was 2.47 for complete denitrification. In this study, 50 mg/L methanol (mg CH3OH: NO3 --N = 1.11 ˂ 2.47) was added to the R1 and R2 (Table 2). This amount of methanol was lower than the stoichiometric ratio of 2.47 for complete heterotrophic denitrification (Figure 5).
In the presence of 50 mg/L methanol, the nitrite accumulation was observed due to insufficient organic carbon (Figure 5).
115 mg/L methanol was added to the R3 and R4 to achieve complete denitrification process. Therefore, the denitrification rate increased with increasing feed methanol concentration as expected (Figure 6). The results with both nitrate and bromate suggest that denitrifying bacteria may be reducing bromate cometabolically.
The main disadvantage of the heterotrophic denitrification is needed external carbon resulting in secondary pollution [16]. On the basis of experimental results, the dissolved organic carbon (methanol) was almost completely removed in batch reactors which mean there was no observation of secondary pollution as illustrated in Figure 7. It was favorable for bromate and nitrate removal, especially drinking water treatment.
The exact bromate reduction mechanism by mixed denitrifying population is not known. It seems that bromate is cometabolically reduced by denitrifiers in the presense of nitrate.
Conclusions
Experiments showed that the denitrification rate was increased with increasing initial NO3 --N concentration. As a result of sulfur-based autotrophic denitrification, effluent SO4 2- concentration increased at the end of the process. Effluent bromide measurements indicated that bromate was completely reduced without accumulation of by-products. Additionally, the effect of methanol concentration on bromate reduction by heterotrophic denitrification process was investigated. Batch studies show that NO2 --N accumulation was observed when methanol was added at methanol/NO3 --N ratio which was lower than the stoichiometric value (mg CH3OH: NO3 --N = 1.11 ˂ 2.47). This study showed that denitrification process was much faster and nitrite accumulation was not observed when adequate methanol was added. This study can be a contribution for the development of a biological process to remove the bromate and nitrate pollution from drinking water.
References
Gunten UV, Pinkernell U: Ozonation of bromide-containing drinking waters:a delicate balance between disinfection and bromate formation. Water Sci Technol 2000,41(7):53–59.
Assunçao A, Martins M, Silva G, Lucas H, Coelho MR, Costa MC: Bromate removal by anaerobic Bacterial community: mechanism and phylogenetic characterization. J Haz Mat 2011, 197: 237–243.
Butler R, Godley A, Lytton L, Cartmell E: Bromate environmental contamination: review of impact and possible treatment. Crit Rev Environ Sci Technol 2005, 35: 193–217. 10.1080/10643380590917888
Yesilnacar MI, Sahinkaya E, Naz M, Ozkaya B: Neural network prediction of nitrate in groundwater of Harran Plain, Turkey. Environ Geol 2008, 56: 19–25. 10.1007/s00254-007-1136-5
Rocca CD, Belgiorno V, Meriç S: Overview of in-situ applicable nitrate removal processes. Desalination 2007, 204: 46–62. 10.1016/j.desal.2006.04.023
Sierra-Alvarez R, Beristan-Cordosa R, Salazar M, Gomez J, Razo-Flores E, Field JA: Chemolithotrophic denitrification with elemental sulfur for groundwater treatment. Water Res 2007, 41: 1253–1262. 10.1016/j.watres.2006.12.039
Hijnen WAM, Jong R, Kooij VD: Bromate removal in a denitrifying bioreactor used in water treatment. Water Res 1999,33(4):1049–1053. 10.1016/S0043-1354(98)00306-6
Kirisits M, Snoeyink V, Kruithof J: The reduction of bromate by granular activated carbon. Water Res 2000,34(17):4250–4260. 10.1016/S0043-1354(00)00189-5
Sahinkaya E, Dursun N, Kilic A, Demirel S, Uyanik S, Cinar O: Simultaneous heterotrophic and sulfur-oxidizing autotrophic denitrification process for drinking water treatment: control of sulfate production. Water Res 2011, 45: 6661–6667. 10.1016/j.watres.2011.09.056
Sahinkaya E, Dursun N: Sulfur-oxidizing autotrophic and mixotrophic denitrification processes for drinking water treatment: Elimination of excess sulfate production and alkalinity requirement. Chemosphere 2012, 89: 144–149. 10.1016/j.chemosphere.2012.05.029
Hijnen WAM, Voogt R, Veenendaal H, Jaght VD, Kooij VD: Bromate reduction by denitrifyng bacteria. Appl and Environ Microbiol 1995,61(1):239–244.
Matos CT, Velizarov S, Reis MAM, Crespo JG: Removal of bromate from drinking water using ion exchange membrane bioreactor concept. Environ Sci Technol 2008, 42: 7702–7708. 10.1021/es801176f
Rijn VJ, Tal Y, Schreier HJ: Denitrification in recirculating systems: theory and applications. Aquacultural Engineering 2006, 34: 364–376. 10.1016/j.aquaeng.2005.04.004
Guven D: Effects of different carbon sources on denitrification efficiency associated with culture adaptation and C/N ratio. Clean - Soil Air Water 2009,37(7):565–573. 10.1002/clen.200800198
Liu H, Jiang W, Wan D, Qu J: Study of a combined heterotrophic and sulfur autotrophic denitrification technology for removal of nitrate in water. J Haz Mat 2009, 169: 23–28. 10.1016/j.jhazmat.2009.03.053
Zhao Y, Feng C, Wang Q, Yang Y, Zhang Z, Sugiura N: Nitrate removal from groundwater by cooperating heterotrophic with autotrophic denitrification in a biofilm-electrode reactor. J Haz Mat 2011, 192: 1033–1039. 10.1016/j.jhazmat.2011.06.008
Acknowledgements
This research was funded by The Scientific and Technological Research Council of Turkey (TUBITAK Project No: 111Y165).
Author information
Authors and Affiliations
Corresponding author
Additional information
Competing interests
The authors declare that they have no competing interests.
Authors’ contributions
Corresponding author (SD) carried out design of the study, performed the batch experiments and drafted the manuscript. IB participated in batch reactor design. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
This article is published under license to BioMed Central Ltd. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Demirel, S., Bayhan, I. Nitrate and bromate removal by autotrophic and heterotrophic denitrification processes: batch experiments. J Environ Health Sci Engineer 11, 27 (2013). https://doi.org/10.1186/2052-336X-11-27
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/2052-336X-11-27