Abstract
The influence of nanoparticles introduced into a molten weld pool using a flux-cored wire on the structure and impact toughness of the weld metal is considered. The use of a flux-cored wire with tungsten carbide particles is shown to decrease the scatter of the impact toughnesses of the weld metal. The use of titanium carbide allows one to increase the average impact toughness.
Similar content being viewed by others
REFERENCES
V. B. Litvienko-Arkov et al., “Weld metal structure and properties of the C–Fe–Cr–Ni–Mo–Ti–N system,” Svarka Diagnost., No. 2, 16–19 (2013).
I. V. Zorin et al., “Mandrel of a pipe-rolling camp welding by Ni3Al-based alloy with the use of composite wire,” Svarka Diagnost., No. 2, 20–23 (2016).
G. N. Sokolov, A. S. Troshkov, V. I. Lysak, A. V. Samokhin, Yu. V. Blagoveshchenskii, N. V. Alekseev, and Yu. V. Tsvetkov, “Effect of nanodispersed WC and nickel carbides on the structure and properties of the weld metal,” Svarka Diagnost., No. 3, 36–38 (2011).
S. V. Makarov and S. B. Sapozhkov, “Production of electrodes for manual arc welding using nanodisperse materials,” World Appl. Sci. J. 29, 720–723 (2014).
A. S. Troshkov et al., “Structure and properties of the low carbon metal deposited under ceramic flux containing composite Ni-nanodisperse WC microspheres,” Izv. VSTU, No. 9 (96), 187–190 (2012).
D. A. Gushchhin, “Efficiency increase of the weld metal modification in low-alloy steel welding with a metalochemical additive,” Extended Abstract of Cand. Sci. (Eng.) Dissertation, Moscow, 2017.
I. V. Zorin et al., “Composite wires for surfacing alloys based on nickel and titanium aluminides,” Svarka Diagnost., No. 3, 31–35 (2011).
A. S. Pankratov, “Weld metal modification by tungsten carbides and titanium nitride nanoparticles in flux welding of the low-carbon low alloy steel,” Extended Abstract of Cand. Sci. (Eng.) Dissertation, Moscow, 2017.
V. D. Kuznetsov, I. V. Smirnov, and K. P. Shapovalov, “Effect of nano-additives on the structure and properties of seam metal in welding high-strength low-alloy steels,” Progr. Tekhnol. Sist. Mashinobuduvan., No. 1–2, 143–150 (2013).
A. A. Linnik, “Technological methods development of the weld metal modification by nanoparticles using flux-cored wires in flux welding,” Extended Abstract of Cand. Sci. (Eng.) Dissertation, Moscow, 2017.
N. P. Aleshin et al., “The influence of nanoparticles introduced into molten-pool tail on the impact toughness of weld metal,” Nanotechnol. Russ. 12, 409–415 (2017).
ACKNOWLEDGMENTS
This work was supported by applied researches of the Ministry of Education and Science of the Russian Federation (unique identifier of the project RFMEFI57816X0216).
Author information
Authors and Affiliations
Corresponding author
Additional information
The article was translated by the authors.
Rights and permissions
About this article
Cite this article
Aleshin, N.P., Brovko, V.V., Kobernik, N.V. et al. Influence of Tungsten Carbide and Titanium Carbide Nanoparticles on the Structure and Properties of the Weld Metal. Russ. Metall. 2018, 820–825 (2018). https://doi.org/10.1134/S0036029518090033
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0036029518090033