Abstract
In this study, the burst pressure of thin-walled pressure vessels made of carbon steel is numerically simulated and verified by experimental results. The effect of the length-to-diameter ratio on the burst pressure is analyzed. The numerical and experimental results are compared.
This is a preview of subscription content, log in via an institution to check access.
REFERENCES
N. Dwivedi, V. Kumar, A. Shrivastava, and R. Nareliya, “Burst Pressure Assessment of Pressure Vessel Using Finite Element Analysis: A Review," J. Press. Vess. Technol. 135 (4), 1–5 (2013); DOI: 10.1115/1.4023422.
A. Subhananda Rao, G. Venkata, and B. Nageshwara Rao, “Effect of Long-Seam Mismatch on the Burst Pressure of Maraging Steel Rocket Motor Cases," Eng. Failure Anal. 12 (2), 325–336 (2005); DOI: 10.1016/j.engfailanal.2004.01.004.
G. H. Majzoobi, G. H. Farrahi, and A. H. Mahmoudi, “A Finite Element Simulation and an Experimental Study of Autofrettage for Strain Hardened Thick-Walled Cylinders," Materials Sci. Eng: A 395 (1/2), 326–331 (2003); DOI: 10.1016/S0921-5093(03)00398-8.
L. Xue, Elastic and Inelastic Finite Element Analysis of Cylindrical Shell Intersections (Marquette Univ., 2006).
N. L. Svensson, “Bursting Pressure of Cylindrical and Spherical Vessels," Trans. ASME, J. Appl. Mech. 80 (25), 89–96 (1958).
J. H. Faupel, “Yielding and Bursting Characteristics of Heavy-Walled Cylinders," Trans. ASME, J. Appl. Mech. 78 (23), 1031–1064 (1956).
C. X. Zheng and S. H. Lei, “Research on Bursting Pressure Formula of Mild Steel Pressure Vessel," J. Zhejiang Univ. Sci. A 7, 277–281 (2006); DOI: 10.1631/jzus.2006.as0277.
X. K. Zhu and B. N. Leis, “Average Shear Stress Yield Criterion and Its Application to Plastic Collapse Analysis of Pipelines," Int. J. Press. Vess. Piping 83 (9), 663–671 (2006); DOI: 10.1016/j.ijpvp.2006.06.001.
X. K. Zhu and B. N. Leis, “Evaluation of Burst Pressure Prediction Models for Line Pipes," Int. J. Press. Vess. Piping 89, 85–97 (2012); DOI: 10.1016/j.ijpvp.2011.09.007.
M. Law and G. Bowie, “Prediction of Failure Strain and Burst Pressure in High Yield to Tensile Ratio Line Pipes," Int. J. Press. Vess. Piping 84 (8), 487–492 (2007); DOI: 10.1016/j.ijpvp.2007.04.002.
T. Christopher, B. S. V. Rama Sarma, P. K. Govindan Potti, et al. “A Comparative Study on Failure Pressure Estimations of Unflawed Cylindrical Vessels," Int. J. Press. Vess. Piping 79 (1), 53–66 (2002); DOI: 10.1016/S0308-0161(01)00126-0.
B. F. Langer, “PVRC Interpretive Report of Pressure Vessel Research. Sect. 1. Design Considerations," Welding Res. Council Bull. 95, 1–53 (1964).
E. Upitis and K. MoKhtarian, “Evaluation of Design Margins for Section VIII, Division 1 and Division 2 of the ASME Boiler and Pressure Vessel Code," Welding Res. Council Bull. 435, 1–85 (1998).
C. W. Jin, L. Z. Wang, and Y. Q. Zhang, “Strength Differential Effect and Influence of Strength Criterion on Burst Pressure of Thin-Walled Pipelines," Appl. Math. Mech. 33 (11), 1361–1370 (2012); DOI: 10.1007/s10483-012-1628-7.
A. Kaptan and Y. Kisioglu, “Determination of Burst Pressures and Failure Locations of Vehicle LPG Cylinders," Int. J. Press. Vess. Piping 84 (7), 451–459 (2007); DOI: 10.1016/j.ijpvp.2007.02.004.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, 2023, Vol. 64, No. 1, pp. 13-21. https://doi.org/10.15372/PMTF20230102.
Rights and permissions
About this article
Cite this article
Lu, Z., Cui, Y., Xu, H. et al. EFFECT OF THE LENGTH-TO-DIAMETER RATIO ON THE BURST PRESSURES OF THIN-WALLED PRESSURE VESSELS. J Appl Mech Tech Phy 64, 10–17 (2023). https://doi.org/10.1134/S0021894423010029
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0021894423010029