Abstract
This article presents the details of design and development of a mobile and low-cost measuring device that can directly measure the thermal conductivity of a material. The device does not need an AC power source and needs only a battery to operate. In its operation, the output of a platinum resistance thermometer (PT100 sensor) is amplified by LM324 Quad differential input operational amplifier and fed to Microchip PIC16F877A microcontroller through an analog-to-digital converter. The microcontroller calculates the thermal conductivity of the material by a given set of temperature difference and finally the result is displayed on a liquid crystal display. PIC Basic programming language is used to program the PIC microcontroller. The analog circuit and printed circuit board layout are designed using OrCAD software. It has been observed that the proposed device can measure the temperature with an accuracy of 0.5°C and thermal conductivity with an accuracy of 0.01 W/mm °C. The power consumption of the device is found to be 277.25 mW.
Similar content being viewed by others
References
Speyer, R.F., Thermal Analysis of Materials, Marcel Dekker, New York, 1994.
Xamán, J., Lira, L., and Arce, J., “Analysis of the temperature distribution in a guarded hot plate apparatus for measuring thermal conductivity,” Applied Thermal Engineering, 29(4):617–623 (2009).
Huang, B.L., Ni, Z., Millward, A., McGaughey, A.J.H., et al., “Thermal Conductivity of a Metal-Organic Framework (MOF-5): Part II. Measurement,” International Journal of Heat and Mass Transfer, 50:405–411 (2007).
Assael, M.J., Antoniadis, K.D., and Tzetzis, D., “The Use of the Transient Hot-Wire Technique for Measurement of the Thermal Conductivity of an Epoxy-Resin Reinforced with Glass Fibers and/or Carbon Multi-Walled Nanotubes,” Composites Science and Technology, 68(15–16):3178–3183 (2008).
Parker, W.J., Jenkins, R.J., Butler, C.P., and Abbot, G.L., “FLASH Method of Determining Thermal Diffusivity, Heat Capacity and Thermal Conductivity,” Journal of Applied Physics, 32:1679–1684 (1961).
Mathis, N., “Transient Thermal Conductivity Measurements: Comparison of Destructive and Nondestructive Techniques,” High Temperatures—High Pressures, 32:321–327 (2000).
Cahill, D.G., “Thermal Conductivity Measurement from 30 to 750 K: The 3ω Method,” Review of Scientific Instruments, 61:802–808 (1990).
Cahill, D.G., Katiyar, M., and Abelson, J.R., “Thermal Conductivity of a-Si:H Thin Films,” Physical Review B, 50:6077–6081 (1994).
Oh, D.-W., Jain, A., Eaton, J.K., Goodson, K.E., and Lee, J.S., “Thermal conductivity Measurement and Sedimentation Detection of Aluminum Oxide Nanofluids by Using the 3-ω Method,” International. Journal of Heat and Fluid Flow, 29:1456–1461 (2008).
Govorkov, S., Ruderman, W., Horn, M.W., Goodman, R.B. and Rothschild, M., “A New Method for Measuring Thermal Conductivity of Thin Films,” Review of Scientific Instruments, 68:3828–3834 (1997).
Jackson, W.B., Amer, N.M., Boccara, A.C., and Fournier, D., “Photothermal Deflection Spectroscopy and Detection,” Applied Optics, 20:1333–1344 (1981).
Jeona, P.S., Kima, J.H., Kimb, H.J., and Yoob, J., “Thermal Conductivity Measurement of Anisotropic Material Using Photothermal Deflection Method,” Thermochimica Acta, 477:32–37 (2008).
Calzona, V., Cimberle, M.R., Ferdeghini, C., Putti, M., and Siri, A.S., “Fully Automated Apparatus for Thermal Diffusivity Measurements on HTSC in High Magnetic Field,” Review of Scientific Instruments, 64:766–773 (1993).
Solórzano, E., Reglero, J.A., Rodríguez-Pérez, M.A., Lehmhus, D., Wichmann, M., and De Saja, J.A., “An Experimental Study on the Thermal Conductivity of Aluminium Foams by Using the Transient Plane Source Method,” International Journal of Heat and Mass Transfer, 51(25–26):6259–6267 (2008).
Kuwahara, M., Suzuki, O., Takada, S., Hata N., Fons, P., and Tominaga, J., “Thermal conductivity Measurements of Low-k Films Using Thermo-reflectance Phenomenon,” Microelectronic Engineering, 85:796–799 (2008).
Hu, M., Yu, D., and Wei, J., “Thermal Conductivity Determination of Small Polymer Samples by Differential Scanning Calorimetry,” Polymer Testing, 26:333–337 (2007).
Banaszkiewicz, M., Seweryn, K., and Wawrzaszek, R., “A Sensor to Perform In-Situ Thermal Conductivity Determination of Cometary and Asteroid Material,” Advances in Space Research, 40:226–237 (2007).
Tan, J.C., Tsipas, S.A., Golosnoy, I.O., Curran, J.A., Paul, S., and Clyne, T.W., “A Steady-State Bi-Substrate Technique for Measurement of the Thermal Conductivity of Ceramic Coatings,” Surface & Coatings Technology, 201:1414–1420 (2006).
Subramanian, C.S., Amer, T., UpChurch, B.T., Alderfer, D.W., Burkett, C., and Sealey, B., “New Device and Method for Measuring Thermal Conductivity of Thin-Films,” ISA Transactions, 45(3):313–318 (2006).
Vahanyan, A.I., “A Method for the Thermal Conductivity Measurement of Semiconductors,” Measurement 39:447–450 (2006).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Rehman, M., Mujeebu, M.A., Kheng, T.B. et al. A microprocessor-based novel instrument for temperature and thermal conductivity measurements. Exp Tech 36, 62–70 (2012). https://doi.org/10.1111/j.1747-1567.2010.00698.x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1111/j.1747-1567.2010.00698.x