Skip to main content
SpringerLink
Log in

A new approach for determining the induced drilling stresses in the hole-drilling method of residual-stress measurement

  • Original Article
  • Published:
Experimental Techniques Aims and scope Submit manuscript

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

References

  1. Flaman, M.T., “Brief Investigation of Induced Drilling Stresses in the Center-hole Method of Residual-stress Measurement,” EXPERIMENTAL MECHANICS, 22 (1), 26–30 (Jan. 1982).

    Article  Google Scholar 

  2. Flaman, M. T., “Comparison of Four Hole-Producing Techniques for the Center-Hole Residual-Stress Measurement Method,” EXPERIMENTAL TECHNIQUES, 9 (8), 30–32 (Aug. 1985).

    Article  Google Scholar 

  3. Beaney, E.M., “Accurate Measurement of Residual Stress on Any Steel Using the Center Hole Method,” STRAIN, Journal of BSSM, 12 (3), 99–106 (July 1976).

    Article  Google Scholar 

  4. Bush, A.J. and Kromer, F.J., “Simplification of the Hole-Drilling Method of Residual Stress Measurement,” ISA Trans., 12 (3), 249–259 (1973).

    Google Scholar 

  5. Beaney, E.M. and Procter, E., “A Critical Evaluation of the Centre Hole Technique for the Measurement of Residual Stresses,” STRAIN, Journal of BSSM, 10 (1), 7–14 (Jan. 1974).

    Article  Google Scholar 

  6. Nawwar, A.M., McLachlan, K. and Shewchuk, J., “A Modified Hole-drilling Technique for Determining Residual Stresses in Thin Plate,” EXPERIMENTAL MECHANICS, 16 (6), 226–232 (June 1976).

    Article  Google Scholar 

  7. SEM Residual Stress Measurement Committee, Secretary J.J. Yavelak, “Bulk-Zero Stress Standard AISI1018 Carbon Steel Specimens, Round Robin Phase I,” EXPERIMENTAL TECHNIQUES, 9 (4), 38–41 (April 1985).

    Article  Google Scholar 

  8. Leggatt, R.H., “Evaluation of the Effects of Different Methods of Material Removal on Residual Stresses Measured,” BSSM Int. Conf. on Product Liability and Reliability, Univ. of Aston, Birmingham (Sept. 1980).

    Google Scholar 

  9. Staudhammer, K.P., Murr, L.E. and Hecker, S.S., “Nucleation and Evolution of Strain-induced Martensitic (B.C.C.) Embryos and Substructure in Stainless Steel,” Acta Metallurgica, 31 (2), 267–274 (Feb. 1983).

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Civil Engineering, National Chiao Tung University, Hsinchu, Taiwan, R.O.C.

    C. C. Weng (SEM Member, Associate Professor)

  2. Department of Mechanical Engineering, National Chiao Tung University, Hsinchu, Taiwan, R.O.C.

    Y. C. Lin (Graduate Student) & C. P. Chou (Professor)

Authors
  1. C. C. Weng
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Y. C. Lin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. C. P. Chou
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Weng, C.C., Lin, Y.C. & Chou, C.P. A new approach for determining the induced drilling stresses in the hole-drilling method of residual-stress measurement. Exp Tech 16, 33–35 (1992). https://doi.org/10.1111/j.1747-1567.1992.tb00704.x

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1111/j.1747-1567.1992.tb00704.x

Search

Navigation