Abstract
Infected petals are often regarded as the source for the spread of fungi Sclerotinia sclerotiorum in all growing process of rapeseed (Brassica napus L.) plants. This research aimed to detect fungal infection of rapeseed petals by applying hyperspectral imaging in the spectral region of 874–1734 nm coupled with chemometrics. Reflectance was extracted from regions of interest (ROIs) in the hyperspectral image of each sample. Firstly, principal component analysis (PCA) was applied to conduct a cluster analysis with the first several principal components (PCs). Then, two methods including X-loadings of PCA and random frog (RF) algorithm were used and compared for optimizing wavebands selection. Least squares-support vector machine (LS-SVM) methodology was employed to establish discriminative models based on the optimal and full wavebands. Finally, area under the receiver operating characteristics curve (AUC) was utilized to evaluate classification performance of these LS-SVM models. It was found that LS-SVM based on the combination of all optimal wavebands had the best performance with AUC of 0.929. These results were promising and demonstrated the potential of applying hyperspectral imaging in fungus infection detection on rapeseed petals.
Similar content being viewed by others
Introduction
Rapeseed (Brassica napus L.) is an important oil crop which is widely cultivated all around the world. High energy and protein livestock feed are mainly made from its seeds. It is also partly used as potential raw material in synthesizing biodiesel1. Sclerotinia sclerotiorum (S. sclerotiorum) is a serious and ubiquitous worldwide fungal pathogen of rapeseed plants2. The fungus infects leaves, stems, and pods, resulting in a tremendous loss in seed yield3. For example, sclerotinia stem rot of rapeseed plants in China leads to oilseed yield loss ranging from 10 to 80%, and oil quality declines as well4. As an important pathogen of rapeseed plants, S. sclerotiorum can enter leaves or stems via petals. The infection of rapeseed petals is the first step for the development of S. sclerotiorum on rapeseed plants because mycelium on the infected petals can penetrate into tissues of other organs5. A report showed that the numbers of petals and stamens sticking to rapeseed leaves are a guide to estimate the risk of leaves or stem rot status6. To avoid routine spraying, early diagnosis of the prevalence and severity of disease is required so that treatment can be rationalized7. Previously, various molecular techniques including enzyme-linked immunosorbent assay (ELISA) and polymerase chain reaction (PCR) are developed to assay the risk of fungal infection8,9,10. However, the disadvantages of these methods include expensive, labor-intensive, time-consuming, and tedious extraction procedures, what’s more, these detection methods mostly pointed at an individual plant, and are limited for the large-scale agricultural production11. Therefore, it would be beneficial if a rapid, reliable and nondestructive technique is implemented in detecting the infected petals, so as to predict the risk of disease and provide a guideline for spraying.
Spectroscopic techniques as potential method have been proved successful in detecting plants diseases8. Near infrared spectroscopy12,13, thermal infrared spectroscopy14 and Raman spectral techniques15,16,17 have been intensively applied to detect various diseases on plants. Unfortunately, these methods have their own limitations: spectroscopic technique is often used to measure the averaged spectrum of the sample, but is fails to provide the spectral details at each pixel on images of the targets; thermal infrared measurement often affected by the temperature of the target’s surrounding and Raman information often affected by fluorescence signals which generated in the biological tissue. Thus, hyperspectral imaging is considered as the most promising method in detecting fungal infection of plants.
Hyperspectral imaging is an innovative technology with high potential for the non-invasive sensing of the physiological status of field crops. Hyperspectral imaging is expected to improve the accuracy of disease detection through a better examination of host-pathogen interactions by measuring the pixel-wise information of disease-specific symptoms18. This newly developed technology has been used in an assessment of plant nutrient19,20,21,22,23,24 and plant disease2,18,25,26,27,28,29. Xu et al.2 developed a new Band Math-ROC (receiver operating characteristic) curve algorithm which effectively detect early lesions on oilseed rape leaves caused by S. sclerotiorum and Botrytis cinerea in the first two days after inoculation. Zhao et al.25 employed hyperspectral imaging to determine spatial distributions of chlorophyll and carotenoid contents in cucumber leaves in response to five severities of angular leaf spot (ALS) disease. Texture features combined with spectral information has a potential in detecting early blight and late blight diseases on tomato leaves27. Hyperspectral and thermal imaging were used to detect biotic stresses caused by fungal species on oilseed rape leaves28. Rumpf et al.29 applied support vector machines (SVM) and spectral vegetation indices to realize early detection and classification of various plant diseases based on hyperspectral reflectance. Mahlein et al.18 mapped spectral reflectance enabled the detection and detailed description of diseased tissue on the leaf level based on hyperspectral imaging.
Therefore, this research aim to detect fungal infection of rapeseed petals by using hyperspectral imaging for providing a reference to develop a portable detector that is capable of early diagnosis of S. sclerotiorum disease on rapeseed plants. In the present study, near infrared (NIR) hyperspectral imaging was firstly employed to detect fungal infection on rapeseed petals. The specific objectives were to (1) acquiring hyperspectral images of healthy and infected petals; (2) conducting cluster statistics using principal component analysis (PCA); (3) selecting optimal wavebands based on X-loadings of the first principal components (PCs) and Random frog algorithm; (4) establishing least squares-support vector machine (LS-SVM) models by full and selected wavebands; (5) employing receiver operating characteristic (ROC) curves to evaluate the performance of these discriminative models.
Results and Discussion
Overview of the mean spectra of rapeseed petals
A total of 238 wavebands in the range of 900–1700 nm were selected to remove the noise at the begging and the end of wavelengths. The mean spectra of petals covering the spectral range of 900–1700 nm are presented in Fig. 1. It can be observed that there were no visibly noticeable differences between the healthy and infected petals. Some broadband peaks or valleys occurred in the NIR region in Fig. 1, it can be explained by NIR spectral region contained rich information relevant to the hydrogen containing bonds (such as O-H, C-H, and N-H)30. Feature valleys at 980 nm and 1450 nm (the second and first O-H stretching overtones) are connected with water. Additionally, a small valley around 1200 nm (the second C-H stretching overtone) was due to the organic matter content in samples31. Meanwhile, the spectral reflectance at the wavelengths of 980 nm and 1450 nm showed a sharp difference between the curves of healthy and infected petals worth nothing. What’s more, infected petals have higher reflectance than healthy samples, which might be explained by the decay phenomenon of infected petals.
Although some differences could be observed in Fig. 1, it’s impossible to estimate the infected petals directly merely based on the spectra. Thereby, chemometrics were employed to extract and concentrate the connotative information for further discriminating the healthy and infected rapeseed petals.
Operation of PCA
PCA was employed to transform the full wavebands (238 wavebands) into several principal components (PCs). X-loadings of first PCs were applied for qualitatively identifying the optimal wavebands that were responsible for the specific features. The first three PCs explained 99% original variations and their score plots are displayed in Fig. 2. Each point in these scatter plots represented one spectrum from one sample. Figure 2(a, b, and c) showed the clustering of two groups within the space of PC-1 and PC-2, PC-1 and PC-3, PC-2 and PC-3, respectively. In Fig. 2(a), there was a slight cross between the healthy and infected samples. In contrast, two groups of samples provided an apparent clustering in Fig. 2(b) and (c). The spectra of the infected sample were mainly scattered on the positive sides of PC-3 in Fig. 2(b) and (c), while spectra of healthy group tended to be on the negative side of PC-3 in Fig. 2(b) and (c). To sum up, the score plots distinguished the healthy and infected petals clearly.
Selection of optimal wavebands
Selection of optimal wavebands is of critical significance for removing the redundant information from high-dimensional data, optimizing calibration models and producing excellent results32. Thus, identification of optimal wavebands carrying the most valuable and authentic information is a challenging task in the current hyperspectral data analysis. The X-loadings of PC-1 to PC-3, which revealed the importance of the analyzed variables, are shown in Fig. 3. Variable with large positive or negative loading coefficient was significant and considered as an optimal waveband. The first three loading plots of PCA indicated that the reflectance at two wavelengths of 1446 and 1656 nm with the relatively large loading coefficients had the greatest discriminatory effect on healthy and infected petals. The identified optimal waveband at 1446 nm was close to the first overtones O-H stretching near 1450 nm31, which implied that water content was an important factor to distinguish healthy and infected rapeseed petals.
One-way analysis of variance (ANOVA) was used to reveal the difference of the spectra between healthy and infected petals at 1446 and 1656 nm. The statistical results are shown in Table 1. The letter a, b represent the significant difference of the samples. An apparent difference between the two groups was revealed from the spectral reflectance at 1446 nm, which contributed to the different water content of healthy and infected petals. However, optimal waveband selection by PCs of X-loadings neglect the influence from categorical value of the samples.
Before RF analysis, SPXY method proposed by Galvao et al.33 was implemented to divide the spectral matrix and corresponding labeled classes into calibration sets with 165 samples (95 healthy and 70 infected samples) and prediction sets with 82 samples (47 healthy and 35 infected samples) for subsequent hyperspectral analyses.
RF was performed 50 times and the average value of these 50 runs was taken as the criterion for estimating the importance of each variable. The selection probability (SP) of each wavelength is shown in Fig. 4. From the SP curve, the SP of the most wavelengths offered relatively low values, whereas a small number of wavelengths exhibited extremely high SP values. Based on SP values, wavelengths with high SP (SP > 0.7) were viewed as the optimal wavelengths and labeled in the corresponding position in this study. This result indicated that the majority of wavelengths provided a weak or void relevance to the discrimination of healthy and infected rape flower samples. All the variables were ranked in descending order according to the SP value. Lastly, based on the SP curves in Fig. 4 (threshold value was set as 0.7), four wavelengths at 1190, 1460, 1463, and 1524 nm were selected as optimal wavelengths for infected petals discrimination. The selected optimal wavebands of 1460 and 1463 nm were assigned to first overtones O-H stretching around 1450 nm. The optimal waveband of 1190 nm was close to the second overtones of C-H stretching near 1210 nm34,35. The remaining selected optimal waveband were ascribed to the absorption peak of N-H group in the biological tissue36. Different optimal wavebands were identified by different selection methods for a different feature selection criterion of each method.
Establishment and evaluation of the LS-SVM model
LS-SVM methodology was employed to establish models based on full wavebands (Full-LS-SVM), optimal wavebands (1190, 1460, 1463, and 1524 nm) selected by RF (RF-LS-SVM), optimal wavebands identified by X-loadings of PCs (XL-LS-SVM), a combination of optimal wavebands from RF and X-loadings (RX-LS-SVM), and an important wavelength (1446 nm-LS-SVM) in detecting the infected rapeseed petals, respectively. Recognition rate (RR) of each classification model are presented in Table 2. Results showed that the Full-LS-SVM has an accuracy of 100%, nevertheless, it is not suitable for real-time assessment due to the mass data. The XL-LS-SVM with only two optimal wavelengths (99.16% variables were removed) provided almost the same accuracy with the RF-LS-SVM based on four optimal wavelengths (98.31% variables were removed), hence, the XL-LS-SVM model had better performance than the RF-LS-SVM classification model. The RX-LS-SVM with RR of 92.68% had the best classification result than other models, meanwhile, 97.48% (6 vs. 238) variables were eliminated in the optimal wavebands selection process. Although there was significant difference in healthy and infected rapeseed petals at 1446 nm, the 1446-LS-SVM with RR of 69.51% was unsatisfactory to detect infected petals. In conclusion, the RX-LS-SVM discriminative with the combination of optimal wavelengths provided the highest RR in detecting fungus infection on rapeseed petals.
After that, receiver operating characteristics (ROC) curve was employed to evaluate the performance of these LS-SVM models. ROC curves of the three the LS-SVM discriminant models were shown in Fig. 5, AUC in the Full-LS-SVM (Fig. 5a), RF-LS-SVM (Fig. 5b), XL-LS-SVM (Fig. 5b), RX-LS-SVM (Fig. 5c) and 1446-LS-SVM (Fig. 5d) models were 1, 0.849, 0.849, 0.929, and 0.676, respectively. According to the discriminate criterion of AUC37, the Full-LS-SVM has excellent performance in discriminating the infected petals, however, there were 238 wavelengths involved in the modelling, which would slow down the computing speed. By contrast, the RX-LS-SVM with only six optimal wavebands provided excellent classification in detecting the infected petals. Although there was only one waveband in the 1446-LS-SVM model, the AUC of 0.676 displayed in this model is sufficient to detect the infected rapeseed petals. What’s more, most of the optimal wavebands selected by RF and X-loading were related with water molecule35. The results showed that water content in petals is the dominant factor in discriminating the infected rapeseed petals.
Usually, infection via young and healthy living petals is clearly of primary importance in the establishment of S. sclerotiorum on rapeseed, therefore, detection of the infected petals would be of great value in estimating the level of disease risk and recommending of fungicide applications7. Infected petals often fell off from the stamen and covered on the leaves or stems of oilseed rape plants, counting the number of fallen petals on oilseed rape leaves or stems by the rapid method is important for the disease assessment. In addition, rapeseed petals are generally infected by ascospores. Scholars have already applied PCR38 to detect S. sclerotiorum on petals before their fall. Therefore seeking a fast and invasive detection method in detecting ascospores on petals is our future challenge.
Conclusion
This study provides a theoretical basis in detecting fungal infected rapeseed petals with NIR hyperspectral imaging technique and chemometrics. PCA was employed to process cluster analysis of the healthy and infected samples based on the first three PCs. 1446 nm and 1656 nm were extracted according to the X-loadings of the PC-1, PC-2, and PC-3. Meanwhile, one-way analysis of variance (ANOVA) was used to analyze the significant difference of the reflectance at the two wavelengths. Four wavelengths at 1190, 1460, 1463, and 1524 nm were selected as optimal wavelengths to detect the infected petals. ROC showed that LS-SVM established by the six combination optimal wavebands (1190, 1460, 1463, 1524, 1446 and 1656 nm) provided the optimal results to estimate the infection petals. Applying optimal wavelengths to detect fungus infection on rapeseed petals is critical for sensor’s real-time assessment.
Materials and Methods
Samples
In this study, Sclerotinia sclerotiorum were cultured on PDA (Potato dextrose agar) medium, forming mycelial blocks of 5 mm in diameter2. Mycelial blocks were placed onto the rapeseed petals. Fresh flowers of rapeseed plants were collected from an experimental field on April 21st, 2016 at Zhejiang University (120°09′E, 30°14′N), China. All samples were placed in the same condition with constant temperature 25 °C and humidity 85%, some flowers were placed with the hypha and the rest were placed with the agar block as controlled group. Finally, 142 healthy flowers and 105 infected samples were selected from 24 h after inoculation with hypha and agar block by experienced technical personnel. The experimental samples are shown in Fig. 6, all the flowers had similar color, however, the petals of healthy flower were extended and intact, while, the infected petals decayed with water-soaked, some mycelium covered on the petals and petals fell off from the stamen.
Hyperspectral imaging system and images acquisition
A laboratory hyperspectral imaging equipment, which covers the wavelength of 874–1734 nm with 256 wavebands, was used to capture the hyperspectral images of samples with reflectance mode. It consists of a mobile transporter operated by a stepper motor (IRCP0076, Isuzu Optics Crop, Taiwan, China), an assembled illumination with two 150-W quartz tungsten halogen lamps (Fiber-Lite DC950 Illuminator; Dolan Jenner Industries Inc, Boxborough, MA, USA), an imaging spectrograph (ImSpector N17E, Spectral Imaging Ltd., Specim, Finland) with a spectral resolution of 5.0 nm from 874–1734 nm, a CCD camera (C8484–05, Hamamatsu city, Japan) with a zoom lens (OLES23, Specim, Spectral Imaging Ltd., Oulu, Finland), and the area CCD array detector has 372 pixels × 256 bands (spatial × spectral) and operation of these equipment were controlled by a computer. The whole device (except the computer) was fixed in a dark chamber to minimize the effects of ambient light during the sample scanning.
Some parameters needed to be adjusted to acquire clear and undistorted hyperspectral images before scanning samples. Illumination unit should set an appropriate intensity and adjust a proper angel to make the light gather in a linear area of the conveyor belt just below the imaging spectrograph. The distance between samples and lens was 220 mm. All samples placed on the conveyor belt and moved at a speed of 17 mm/s to be scanned with an exposure time of 4 ms during the image acquisition.
Because the existence of dark current in CCD camera and the uneven intensity of illumination in different bands, some bands with weaker light intensity contained bigger noises25. Hence, the raw hyperspectral images (I0) required to be calibrated and the calibration process could be finished using the following Equation (1)39:
![](http://media.springernature.com/lw164/springer-static/image/art%3A10.1038%2Fsrep38878/MediaObjects/41598_2016_Article_BFsrep38878_Equ1_HTML.gif)
where, I were the calibrated hyperspectral images of the samples;
B were the dark reference images obtained with light source off;
W were the white reference images acquired from a white reference ceramic tile. Calibration is the essential for subsequent processing and analysis.
The precondition for extracting the spectral reflectance was by identifying the regions of interest (ROIs) on petals of rapeseed. Based on the irregular and complex shape of rape flower, image segmentation was used to isolate hyperspectral images of rapeseed flowers from background and stem information, and the main process is shown in Fig. 7. There were big differences among the spectrum (peak or peak shape) of petals, stems, and backgrounds based on the pre-analysis. To isolate petals from the stem and background in hyperspectral images, the single band image at 1146 nm (Fig. 7a) with the biggest contrast was selected to process the image segmentation using a threshold (here is 0.5). The resulting segmented image in Fig. 7(b) was considered as the mask to remove the background information. By masking every hyperspectral image with the rape flower mask, the target region of petal hyperspectral images is displayed in Fig. 7(c).
The segmented region was considered as the region of interest (ROI) of the corresponding petal sample. The spectra of each pixel in ROI were averaged and this spectrum was considered as the spectral reflectance of a sample. The spectra of other samples were obtained in the same way as mentioned above. This process was finished in ENVI 4.6 software (ITT visual information solutions, Boulder, CO, USA).
Data analysis
Principal component analysis (PCA) is an unsupervised technique (classes or composition of the samples in the data matrix is not involved) and highly popular in extracting feature and reducing the dimension of multivariate data sets. Mathematically, several principal components (PCs), which are orthonormal and can explain maximum variance, are produced in PCA transform40. Each PC is a linear sum of variables multiplied by corresponding weighting coefficients. Generally, most of the relevant information in initial variables (spectra) can be explained by first several PCs. Meanwhile, the score of PCs is used to reveal the features of variable distribution, and the X-loadings of PCs can exhibit the importance of different variables41.
Random frog (RF) methodology, a novel and efficient technique for variable selection, was carried out to identify optimal wavebands. In principle, RF borrows the framework of reversible jump Markov Chain Monte Carlo (RJMCMC) methods and employed to perform feature extraction for selecting a series of variables which describe the correlation between the predictor variables and the response variables42. In the interior of RF algorithm, partial least squares-linear discriminant analysis (PLS-LDA) is conducted as a modeling method. The relationship between spectral matrix (n × p) consisting of n samples and p variables and property matrix (n × 1) is established. RF works in an iterative manner. The algorithm of RF was fully detailed in literatures42,43. Generally, RF is implemented many times (depending on the data) to weaken the influence caused by Monte Carlo strategy embedded in RF algorithm.
Least-squares support vector machine (LS-SVM), an optimized version of the standard SVM, is a powerful methodology for pattern recognition and function estimation. It could reduce the complexity of the calculation and shorten the needed time to improve the studying ability of high-dimensional characteristic space. LS-SVM classifier has been widely applied in the classification of agricultural productions41,44,45,46. Proper kernel function and optimum kernel parameters are important in LS-SVM model. In this research, radial basis function (RBF) kernel function was adopted to establish the LS-SVM model. In addition, the grid-search and leave one out validation (LOOCV) methods were used to find out the optimal parameter values of regularization parameter γ and the RBF kernel function parameter σ2. The details of LS-SVM could be found in the literature47.
The shape of a receiver operating characteristics (ROC) curve and area under the curve (AUC) were often used to estimate the performance of the discrimination models. In ROC curve, parameter “Sensitivity” denotes sensitivity for each threshold value; factor “1-Specificity” stands for 1-specificity of each threshold value; parameter “area” means area under the ROC curve (AUC); and ingredient “std” represents the standard deviation of the residuals. The closer the curve is located at upper-left hand corner and the large the AUC, the better the test is at discriminating between healthy and infected petals41,48. Generally, the relation between AUC and diagnostic accuracy applies as described in Table 337.
Additional Information
How to cite this article: Zhao, Y.-R. et al. Detection of Fungus Infection on Petals of Rapeseed (Brassica napus L.) Using NIR Hyperspectral Imaging. Sci. Rep. 6, 38878; doi: 10.1038/srep38878 (2016).
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
Wang, C. et al. Influence of leaf and silique photosynthesis on seeds yield and seeds oil quality of oilseed rape (Brassica napus L.). Eur. J. Agron. 74, 112–118 (2016).
Xu, X. & Zhao, Y. A Band Math-ROC operation for early differentiation between sclerotinia sclerotiorum and botrytis cinerea in oilseed rape. Comput. Electron. Agr. 118, 116–123 (2015).
Wang, Z. et al. Overexpression of BnWRKY33 in oilseed rape enhances resistance to Sclerotinia sclerotiorum. Mol. plant pathol. 15, 677–689 (2014).
Wang, J.-X. et al. Sensitivity of Sclerotinia sclerotiorum from oilseed crops to boscalid in Jiangsu Province of China. Crop Prot. 28, 882–886 (2009).
Bečka, D. et al. Use of petal test in early-flowering varieties of oilseed rape (Brassica napus L.) for predicting the infection pressure of Sclerotinia sclerotiorum (Lib.) de Bary. Crop Prot. 80, 127–131 (2016).
Yong, C., Werner, P., West, J. & Drayton, A. D. A. S. Understanding sclerotinia infection in oilseed rape to improve risk assessment and disease escape. HGCA project report 420 (2007).
Jamaux, I., Gelie, B. & Lamarque, C. Early stages of infection of rapeseed petals and leaves by sclerotinia sclerotiorum revealed by scanning electron microscopy. Plant Pathol. 44, 22–30 (1995).
Sankaran, S., Mishra, A., Ehsani, R. & Davis, C. A review of advanced techniques for detecting plant diseases. Comput. Electron. Agr. 72, 1–13 (2010).
Qin, L. et al. A nested-PCR method for rapid detection of sclerotinia sclerotiorum on petals of oilseed rape (Brassica napus). Plant Pathol. 60, 271–277 (2011).
Freeman, J., Ward, E., Calderon, C. & McCartney, A. A polymerase chain reaction (PCR) assay for the detection of inoculum of sclerotinia sclerotiorum. Eur. J. Plant Pathol. 108, 877–886 (2002).
Sharma, R., Kumar, V., Mohapatra, T., Khandelwal, V. & Vyas, G. K. A simple and non-destructive method of direct-PCR for plant systems. Journal of Plant Biology 55, 114–122 (2011).
Liu, Z.-Y., Wu, H.-F. & Huang, J.-F. Application of neural networks to discriminate fungal infection levels in rice panicles using hyperspectral reflectance and principal components analysis. Comput. Electron. Agr. 72, 99–106 (2010).
Gandolfo, D. S., Mortimer, H., Woodhall, J. W. & Boonham, N. Fourier transform infra-red spectroscopy using an attenuated total reflection probe to distinguish between Japanese larch, pine and citrus plants in healthy and diseased states. Spectrochim. acta. Pt. A-Mol. Bio. 163, 181–188 (2016).
Raza, S.-e.-A., Sanchez, V., Prince, G., Clarkson, J. P. & Rajpoot, N. M. Registration of thermal and visible light images of diseased plants using silhouette extraction in the wavelet domain. Pattern Recognit. 48, 2119–2128 (2015).
Yeturu, S. et al. Handheld Raman spectroscopy for the early detection of plant diseases: Abutilon mosaic virus infecting Abutilon sp. Anal. Methods 8, 3450–3457 (2016).
Lawaetz, A. J. et al. Fast, cross cultivar determination of total carotenoids in intact carrot tissue by Raman spectroscopy and partial least squares calibration. Food Chem. 204, 7–13 (2016).
Perez, M. R. et al. Raman spectroscopy an option for the early detection of citrus Huanglongbing. Appl. Spectrosc. 70, 829–839 (2016).
Mahlein, A. K., Steiner, U., Hillnhütter, C., Dehne, H. W. & Oerke, E. C. Hyperspectral imaging for small-scale analysis of symptoms caused by different sugar beet diseases. Plant Methods 8, 1–13 (2012).
Zou, X. B. et al. Independent component analysis in information extraction from visible/near-infrared hyperspectral imaging data of cucumber leaves. Chemometr. Intell. Lab. 104, 265–270 (2010).
Zou, X. B. et al. In vivo noninvasive detection of chlorophyll distribution in cucumber (Cucumis sativus) leaves by indices based on hyperspectral imaging. Anal. Chim. Acta 706, 105–112 (2011).
Shi, J.-Y. et al. Nondestructive diagnostics of nitrogen deficiency by cucumber leaf chlorophyll distribution map based on near infrared hyperspectral imaging. Sci. Hortic-amsterdam 138, 190–197 (2012).
Zhang, X., Liu, F., He, Y. & Gong, X. Detecting macronutrients content and distribution in oilseed rape leaves based on hyperspectral imaging. Biosystems Eng. 115, 56–65 (2013).
Yu, K.-Q., Zhao, Y.-R., Zhu, F.-L., Li, X.-L. & Yong, H. Mapping of chlorophyll and SPAD distribution in pepper leaves during leaf senescence using visible and near-infrared hyperspectral imaging. T. ASABE 59, 13–24 (2016).
Yu, K. Q. et al. Hyperspectral imaging for mapping of total nitrogen spatial distribution in pepper plant. PLoS One 9, e116205 (2014).
Zhao, Y. R., Li, X., Yu, K. Q., Cheng, F. & He, Y. Hyperspectral imaging for determining pigment contents in cucumber leaves in response to angular leaf spot disease. Sci. Rep. 6, 27790 (2016).
Zhang, C., Kong, W., Liu, F. & He, Y. Measurement of aspartic acid in oilseed rape leaves under herbicide stress using near infrared spectroscopy and chemometrics. Heliyon 2, Article e00064 (2016).
Xie, C., Shao, Y., Li, X. & He, Y. Detection of early blight and late blight diseases on tomato leaves using hyperspectral imaging. Sci. Rep. 5, 16564 (2015).
Baranowski, P. et al. Hyperspectral and thermal imaging of oilseed rape (Brassica napus) response to fungal species of the genus Alternaria. PLoS One 10, e0122913 (2015).
Rumpf, T. et al. Early detection and classification of plant diseases with support vector machines based on hyperspectral reflectance. Comput. Electron. Agr. 74, 91–99 (2010).
Wu, D. & Sun, D.-W. Advanced applications of hyperspectral imaging technology for food quality and safety analysis and assessment: A review — Part II: Applications. Innov. Food Sci. Emerg. 19, 15–28 (2013).
Sims, D. A. & Gamon, J. A. Estimation of vegetation water content and photosynthetic tissue area from spectral reflectance: a comparison of indices based on liquid water and chlorophyll absorption features. Remote Sens. Environ. 84, 526–537 (2003).
Xiaobo, Z., Jiewen, Z., Povey, M. J., Holmes, M. & Hanpin, M. Variables selection methods in near-infrared spectroscopy. Anal. Chim. Acta 667, 14–32 (2010).
Galvão, R. K. H. et al. A method for calibration and validation subset partitioning. Talanta 67, 736–740 (2005).
Tsai, C. L., Chen, J. C. & Wang, W. J. Near-infrared absorption property of biological soft tissue constituents. J. Med. Biol. Eng. 21, 7–14 (2001).
Segtnan, V. H., Šašic, Š., Isaksson, T. & Ozaki, Y. Studies on the Structure of water using two-dimensional near-infrared correlation spectroscopy and principal component analysis. Anal. Chem. 73, 3153–3161 (2001).
Maruo, K. & Masami, Oka . Method of determining a glucose concentration in a target by using near-infrared spectroscopy. US Patent No. 5,957,841 9–28 (1999).
Šimundić, A.-M. Measures of diagnostic accuracy: basic definitions. Med Biol Sci 22, 61–65 (2008).
Jamaux, I. & Spire, D. Development of a polyclonal antibody-based immunoassay for the early detection of Sclerotinia sclerotiorum in rapeseed petals. Ptant Pathotogy 43, 847–862 (1994).
Zhao, Y. R., Yu, K. Q. & He, Y. Hyperspectral imaging coupled with random frog and calibration models for assessment of total soluble solids in mulberries. J Anal Methods Chem 2015, 343782 (2015).
Zielinski, A. A. et al. Chemical composition, sensory properties, provenance, and bioactivity of fruit juices as assessed by chemometrics: a critical review and guideline. Compr. Rev. Food Sci. Food Saf. 13, 300–316 (2014).
Li, X., Nie, P., Qiu, Z.-J. & He, Y. Using wavelet transform and multi-class least square support vector machine in multi-spectral imaging classification of Chinese famous tea. Expert Syst. Appl. 38, 11149–11159 (2011).
Li, H.-D., Xu, Q.-S. & Liang, Y.-Z. Random frog: An efficient reversible jump markov chain monte carlo-like approach for variable selection with applications to gene selection and disease classification. Anal. Chim. Acta 740, 20–26 (2012).
Yun, Y.-H. et al. An efficient method of wavelength interval selection based on random frog for multivariate spectral calibration. Spectrochim. Acta, Part A 111, 31–36 (2013).
Gao, J., Li, X., Zhu, F. & He, Y. Application of hyperspectral imaging technology to discriminate different geographical origins of Jatropha curcas L. seeds. Comput. Electron. Agr. 99, 186–193 (2013).
Shao, Y. et al. Discrimination of tomatoes bred by spaceflight mutagenesis using visible/near infrared spectroscopy and chemometrics. Spectrochim. Acta, Part A 140, 431–436 (2015).
Wu, D., Yang, H., Chen, X., He, Y. & Li, X. Application of image texture for the sorting of tea categories using multi-spectral imaging technique and support vector machine. J. Food Eng. 88, 474–483 (2008).
Pelckmans, K.S. J. A. K., Van Gestel, T. et al. LS-SVMlab: a matlab/c toolbox for least squares support vector machines. Tutorial. KULeuven-ESAT. Leuven, Belgium 142, 1–2 (2002).
Yu, K. et al. Identification of crack features in fresh jujube using Vis/NIR hyperspectral imaging combined with image processing. Comput. Electron. Agr. 103, 1–10 (2014).
Acknowledgements
This research was supported by the National Natural Science Foundation of China (31471417), Specialized Research Fund for the Doctoral Program of Higher Education of China (20130101110104).
Author information
Authors and Affiliations
Contributions
Yan-ru Zhao designed the experiment and wrote this manuscript. Ke-qiang Yu managed the data processing and writing of the manuscript. Xiaoli Li revised the manuscript. Yong He reviewed the initial design of the experiments and made guidance for the writing of the manuscript. All authors reviewed the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Zhao, YR., Yu, KQ., Li, X. et al. Detection of Fungus Infection on Petals of Rapeseed (Brassica napus L.) Using NIR Hyperspectral Imaging. Sci Rep 6, 38878 (2016). https://doi.org/10.1038/srep38878
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep38878
- Springer Nature Limited