Abstract
Origami structures enrich the field of mechanical metamaterials with the ability to convert morphologically and systematically between two-dimensional (2D) thin sheets and three-dimensional (3D) spatial structures. In this study, an in-plane design method is proposed to approximate curved surfaces of interest with generalized Miura-ori units. Using this method, two combination types of crease lines are unified in one reprogrammable procedure, generating multiple types of cylindrical structures. Structural completeness conditions of the finite-thickness counterparts to the two types are also proposed. As an example of the design method, the kinematics and elastic properties of an origami-based circular cylindrical shell are analysed. The concept of Poisson’s ratio is extended to the cylindrical structures, demonstrating their auxetic property. An analytical model of rigid plates linked by elastic hinges, consistent with numerical simulations, is employed to describe the mechanical response of the structures. Under particular load patterns, the circular shells display novel mechanical behaviour such as snap-through and limiting folding positions. By analysing the geometry and mechanics of the origami structures, we extend the design space of mechanical metamaterials and provide a basis for their practical applications in science and engineering.
Similar content being viewed by others
Introduction
Origami, the art of folding a sheet into a 3D structure, has recently gained extensive attention in science and engineering1,2. Unique transformational abilities make origami structures widely applicable in fields such as self-folding machines3,4, aerospace engineering5,6, and biomechanics7,8. Although the fundamental relationships of a single origami unit (e.g., a unit of Miura-ori, or water bomb pattern) are understood, geometric relations when these units constitute “modular origami9” should also be understood. Among the many possible research directions in modular origami, the fundamental problem of designing 2D origami tessellations corresponding to desired 3D surfaces is still being studied. This “inverse” design issue has long aroused dissatisfaction10, but significant progress has been made recently11,12, whereas more design methods are still needed for various crease patterns13,14. The mechanics of origami is also of great interest15 and has substantially enriched the potential applications of mechanical metamaterials1,16. Novel stiffness and Poisson’s ratio possibilities, as well as bi/multi-stable properties, are studied for numerous origami patterns2,17,18 to facilitate their potential applications in mechanical actuators and energy absorption19,20,21. Much of the literature is concerned with origami mechanics of the “rectangular” or “cuboid” configuration15,17, and studies on relatively complicated configurations (such as shell structures) are limited. Under some circumstances, deformation modes that involve both folding of creases and bending of plates are considered22,23,24. In many cases, the thickness of the constituent plates cannot be ignored6,25,26. To maintain rigid foldability, thick plates are often separated and linked by thin films6 or extra hinges27. Recently, systematic kinematic models of thick origami are established28. There are stricter geometric compatibility conditions for thick plates (especially for those with periodic units) than zero-thickness plates.
In this paper, we propose a generalized in-plane design method that generates 2D Miura-ori tessellations according to the desired 3D cylindrical surfaces. Using the method, two fold types of Miura-ori crease lines can be unified in one reprogrammable procedure. The structural completeness conditions under which there are no gaps when plates are folded are developed. In particular, the mechanics of one type of cylindrical shell, namely, origami-based circular shells (OCSs), are investigated. First, the collision conditions and auxetic properties of the OCSs are explored. The unique mechanical responses to different loading patterns are demonstrated theoretically and simulated numerically. Moreover, by incorporating elastic properties into the plates, inhomogeneous deformation of the OCSs under radial line forces is numerically simulated.
Results
Generalized in-plane design method for cylindrical structures
Inverse origami design problems have been studied. 2D crease patterns and their corresponding quadrilaterals generated by previous methods11,12 are generally designed in the form shown in the left column of Fig. 1b. In this paper, another design method is proposed that can generate two types of crease patterns. A Miura-ori unit is shown in Fig. 1a. Fundamental geometric relations exist among the dihedral angles (ϕ, φ) and line angles (θ, η), in which ϕ (or its supplementary angle ψ) is chosen as the actuation angle during the folding/unfolding process in this study. The first step of the method is to choose in-plane vertices on/outside the directrix of the cylindrical surface, as shown in Fig. 1b. The folds connected by these vertices (P1, P2, P3 … in Fig. 1a,b) are called “mainlines” (see the black lines in the intermediate state of Fig. 1c,d). The 3D folded configuration that approximates the cylindrical surface of interest is the “prototypical configuration” relative to the 2D and other 3D configurations during folding. The prototypical angles, θiP (i = 1, 2, 3 …), combining the pre-defined height of the quadrilaterals h and the prototypical actuation angle ϕ p constitute all of the independent parameters of the design method. The constant parameter α in Fig. 1a is then determined inversely. The values of θiP are located in-plane, and the orderly quadrilaterals are first formed in an “intermediate state” (this state does not exist in the actual folding process) and then “folded” to 3D space (Fig. 1c,d). More examples generated by the method are presented in Supplementary Information (SI).
Chen et al.28 developed a method to analyse the kinematics of thick origami. Their method is adopted here to investigate the structural completeness conditions of the two fold types discussed above. The conditions here refer to the folding case in which there are no gaps between thick plates. For infinitely thin Miura-ori, a spherical linkage is sufficient to model the kinematics, whereas for thick origami, other types of linkages (such as a spatial 4R-linkage) are necessary. Generally, the distances between the axes of creases are denoted by αi (i = 1–4). According to the constraints of Bennett linkages28,
where αi (i = 1–4) are the line angles divided by the crease lines (Fig. S2). For Miura-ori, the line angles satisfy δ1 = δ2. Therefore, the following relation is obtained:
As shown in Fig. 2a, extra thicknesses bi (i = 1, 2) are necessary to connect the plate-crease-plate to ensure kinematic compatibility. For periodic Miura-ori, b1 = b2 = a should be satisfied because larger bi hinders flat-foldability whereas smaller bi leaves gaps in the structure when completely folded (ϕ = 0°). Note that plates are embedded into the neighbouring plates with thickness αi when completely folded. Therefore, proper cutting of materials is necessary to ensure geometric compatibility. Specifically, as shown in Fig. 2b, to guarantee that no gaps exist after folding, side should intersect with side , where the point of intersection between the two lines is O1 on (or O2 on ). This condition requires the following inequality to be satisfied:
Using the above criterion, we present one specific example to discuss structural completeness conditions of the thick counterparts of these two fold types (Fig. 2c,d). The two patterns are generated naturally using the aforementioned method. In the first pattern, parameters αi and li (i = 1, 2) should satisfy the following constraints to ensure the existence of the intersection point:
Specially, equation (4) reduces to linear constraints: 0 < α1 < 60° and 4α2 − α1 < 180° for l1 = l2 = L. A counterexample that loses completeness is shown in Fig. 2c. In the second pattern, the thick counterparts only maintain completeness when α < 45°, regardless of the ratio l3/l4. When α > 45°, constraint 1 − l3/l4 > 4 cos2α causes the remnant part to completely lose the original geometric information and no longer constitutes periodic thick origami; causes notches in the thick origami formed. Corresponding derivations are shown in SI.
Geometry and mechanics of OCSs
Origami-based cylindrical shells are naturally generated using the developed in-plane method. Here, the geometry and mechanics of a specific case (i.e., OCSs) with the pattern shown in Figs 2c and 3 are investigated. With a pre-chosen constant parameter h and prototypical variables ϕp, θ1p and θ2p, all of the other constants (l1, l2, α1 and α2; α1 < α2) are determined. In 3D folded configurations, “mainlines” (the solid red lines in Figs 2c and 3a,b) are along the circumferential direction, and vertices on them are regularly distributed on two concentric circular surfaces with radii R1 and R2. The variables of OCSs with m × n unit cells are described in terms of the actuation angle ψ as:
where λ is the central angle per unit cell in the circumferential direction and θi (i = 1, 2) are given by:
When the length ratio l1/l2 is given, to ensure geometric compatibility (Fig. 3c), the following constraints should be satisfied: 0 < α1 < α2 < 90° for l1/l2 ≥ 1; α1 and α2 lie within the region enclosed by 0 < α1 < α2 < 90° and for l1/l2 < 1. In the following, the condition l1 = l2 = L is adopted to simplify analysis.
As an OCS is folded and the circumferential number n increases, it may not be intuitively clear what happens when the OCS reaches 360° in the circumferential direction and physical interference occurs. We study the collision conditions by characterizing the magnitude and monotonicity of the central angle λ. Theoretical results (see equations (18, 19) in Methods) reveal that when α1 + α2 < 90°, λ monotonically changes during folding. When α1 + α2 > 90°, however, λ varies non-monotonically and reaches the maximum value at , followed by a gradual decrease to 2(α2 − α1). Based on this monotonicity, the collision conditions of the OCSs are obtained. As shown in Fig. 3d, the angle pair (α1, α2) in the enclosed region guarantees that OCSs maintain foldability throughout the entire folding process. The boundary curves are linear (2n(α2 − α1) = 360°) when α1 + α2 < 90°, whereas they change to
when α1 + α2 > 90° because of the non-monotonicity of λ.
The isometric deformation of OCSs can be quantified using the axial and circumferential strains, εz = dW/W and εθ = dR1/R1 + dΛ1/Λ1, respectively. The smaller radius, R1, is chosen to characterize the strain because the endpoints of R1 reach the outer edges of the structure in the circumferential direction (Fig. 3b). Poisson’s ratio is then extended to curved shell structures as vzθ = −εθ/εz, which is obtained as follows:
where
Figure 3e shows the variation of vzθ as a function of ψ for selected set values of α1 = 10°, 30°, and 50°, and α2 = 60° and 80°. The OCSs are shown to be auxetic, with negative νZθ monotonically increasing to 0 at ψ = 180°. Additionally, νZθ has only a moderate dependence on α1 for a given α2; however, it is very sensitive to α2.
Then, we consider the mechanical responses of OCSs under radial force Fr and axial force Fa, respectively. Models of rigid plates connected by linearly elastic torsional springs with particular initial folding angles are implemented. A constant k, which represents the torque required to twist one spring of unit length over one unit radian, is used to characterize the elastic properties of the springs15. The number of periodic units (m and n) should be considered because of the “boundary effect”. The strain energy U and external work T associated with an OCS are:
where the superscript “init” represents the initial states of corresponding quantities, whereas Fi and χi (i = r, a) are the radial and axial forces and their associated displacements, respectively. According to the principle of minimum potential energy, i.e., δ(U − T) = 0, corresponding balanced forces are then obtained (see SI).
Snap-through transitions of OCSs arise from the axial forces, which are induced by the existence of inflection points in the mechanical energy. Fig. 4a shows the Fa − ψ relationship for selected values of α1 = 45°, α2 = 60° and ψinit = 10°, 35°, and 60°. Apparent snap-through appears for small ψinit. To further characterize the snap-through and hysteresis effects17 and alter these effects by redesigning the folds, we obtain 3D zero-equipotential surfaces of instantaneous stiffness (i.e., ∂Fa/∂ψ = 0) by choosing and controlling the relevant variables. Fig. 4b,c show the surfaces in α2 − ψinit − ψ and α1 − α2 − ψ space, respectively. Radial loads induce another important phenomenon: the existence of a limiting folding position ψc (ψc equals neither 0 nor 180°). When ψ → ψc, Fr(ψc) → ∞. Notably, ψc is independent of ψinit, which indicates that even when OCSs are flat-foldable, we can adjust the foldability by choosing specific crease patterns, load methods, and boundary conditions. For both axial and radial loads, excellent agreement between the analytical and FEM predictions is obtained. More information can be found in SI.
The load-bearing capability and elastic stability of shell structures have received considerable attention. Several recent studies29,30,31 explored inhomogeneous deformation of origami-based structures or creased shells by considering the plates to be elastic instead of rigid. “Pop-through” or other types of defects in origami have been found to cause remarkable stiffness enhancement, and the elastic stability can be adjusted by modifying the crease patterns. Here, FEM is used to study the deformation of elastic OCSs subject to radial loads. The boundary conditions for the periphery along the axial direction are clamped. Simulated force versus displacement curves for three OCSs with different ψinit = 10°, 20°, and 30° are shown in Fig. 5. The creases divide the OCS into multiple plates, and snap-through is initiated at the early stage of deformation (indicated by the circles in Fig. 5a). Multi-stage deformations in a cross section that characterizes the snap-through process are shown in Fig. 5b. For comparison, the force-displacement responses of the equivalent homogeneous cylindrical shells (EHCSs) (i.e., having the same volume of mass, radius, and central angle) are shown in Fig. 5c, revealing deformation different from OCSs. First, the OCSs are much stronger than their equivalent counterparts. Second, the load-displacement curves of the homogeneous shapes are much smoother, and the global load softening occurs much later.
Conclusion and Discussion
This paper proposes a generalized design method for deployable cylindrical structures. By unifying two crease patterns in one reprogrammable procedure and studying the influence of thickness, the method provides a method to construct compact engineering structures. Additionally, the geometry and mechanics of Miura-ori based circular shells are investigated, providing further understanding of mechanical metamaterials, including auxetic properties, snap-through transitions, and limiting folding positions. Such unique and interesting properties of origami structures make them attractive for various applications in science and engineering.
Although the developed in-plane design method has been demonstrated to construct various origami-based cylindrical structures, it is desirable to determine whether the method can be extended to more complex structures such as undevelopable surfaces, even at a less approximate level. Furthermore, all the constituent units are Miura-ori, whereas some other crease patterns, such as water bomb19 and Resch patterns32, can also be adopted to form curved surfaces. Finally, further study on the mechanics of other types of origami shells is planned, especially in the areas of snap-through transitions and the stability of elastic origami.
Methods
Procedures of the in-plane method
The method is called an “in-plane method” because all of the quadrilateral information is determined in-plane (i.e., the “intermediate state” in Fig. 1c,d). Open target curves (e.g., spiral curves) are used as examples to demonstrate the method; the method for closed curves (e.g., the circle and ellipse shown in Fig. 1c) can be obtained with some modification. The unified procedure of the two types of fold patterns is presented as follows:
-
1
Vertices Pi are chosen on two target curves (or one target curve) if a Type-1 (or Type-2) pattern is desired; thus, the values of are determined naturally by the positions of Pi. Using pre-chosen values of φp and h, the desired prototypical 3D configuration is obtained. The Miura-ori shape exhibits a single DOF; thus, according to the fundamental relations between α, ϕ, φ, θ and η of a Miura-ori shape, the values of αi can be calculated as follows:
-
2
For the vertices chosen, the following parameters are determined: length of every “mainline” (i.e., ) li, and angle between every “mainline” and positive x-axis ςi = ςi−1 + 180° − θi. The primary function of the method is to locate the in-plane positions of every trapezoid Pi−1PiQiQi−1 (see Fig. 6a,b and “Intermediate state” in Fig. 1), i.e., positions of point Qi−1 and Qi. Assuming that the vertices are chosen in a counter clockwise manner:
For the Type-1 pattern, when Pi−1 is located on Γ1(1) and Pi on Γ1(2), the Cartesian coordinates of Qi−1 and Qi are as follows:
The next Pi−1 is located on Γ1(2), whereas Pi is located on Γ1(1) (Fig. 1b,c); under this circumstance, the Cartesian coordinates of Qi−1 and Qi are as follows:
Repeating the above procedure generates all of the Type-1 trapezoidal information.
For the Type-2 pattern, when is the shorter bottom of the trapezoid’s two bottoms, the Cartesian coordinates of Qi−1 and Qi are as follows:
The next is the longer bottom of the trapezoid’s two bottoms (Fig. 1b,d), and the Cartesian coordinates of Qi−1 and Qi are as follows:
Repeating the above procedure generates all of the Type-2 trapezoidal information.
3.Because all of the trapezoids have been determined at the intermediate state, rotating them around their respective “mainlines”, for ϕp/2 and −ϕp/2, to the 3D configuration will achieve the desired configuration (see Fig. 1c,d). After repeating these symmetric units in the third dimension, the desired Miura-ori based cylindrical structures are obtained.
The parameter h is one of the pre-chosen parameters in the method. An excessively large value of h causes the two hypotenuses of the trapezoid to intersect (Fig. 6a,b). We specify a general criterion of choosing h to maintain compatibility. For the Type-1 crease pattern, the criterion is as follows:
For the Type-2 crease pattern, the criterion is as follows:
Experimental models of periodic thick OCSs
Using the modelling method established by Chen et al.28, we present an experimental example of periodic thick OCSs. As shown in Fig. 6c,e, the 3 × 2 thick OCS has a cylindrical shape in the folded state. Following equation (2) and taking b1 = b2 = a, we demonstrate that no gaps remain after complete folding (Fig. 6d). The parameters of the sample are: L = l1 = l2 = 10 cm, α1 = 40°, α2 = 50°, and a = b1 = b2 = 0.5 cm.
Collision conditions of OCSs
Monotonicity of the unit central angle λ is assumed to characterize the circumferential expanding ability of the OCSs:
Thus,
Monotonicity of the following function is required to estimate the variation of λ:
Further results indicate that under the assumption that 0 < α1 < α2 < π/2, λ increases (i.e., ) monotonically when α1+ α2 < π/2, whereas for α1 + α2 > π/2, there is only one that results in , which causes λ to first increase to the maximum value and then decrease; when ψ → π, , the OCSs fold completely, and λ approaches a constant value 2(α2 − α1). Thus, we obtain
The OCSs do not self-overlap if and only if , which are the collision conditions of OCSs (Fig. 3d).
Additional Information
How to cite this article: Wang, F. et al. Folding to Curved Surfaces: A Generalized Design Method and Mechanics of Origami-based Cylindrical Structures. Sci. Rep. 6, 33312; doi: 10.1038/srep33312 (2016).
References
Silverberg, J. L. et al. Using origami design principles to fold reprogrammable mechanical metamaterials. Science 345, 647–650 (2014).
Lv, C., Krishnaraju, D., Konjevod, G., Yu, H. & Jiang, H. Origami based Mechanical Metamaterials. Sci. Rep. 4, 5979– 55981(2014).
Felton, S., Tolley, M., Demaine, E., Rus, D. & Wood, R. A method for building self-folding machines. Science 345, 644–646 (2014).
Yang, P.-K. et al. Paper-Based Origami Triboelectric Nanogenerators and Self-Powered Pressure Sensors. ACS Nano 9, 901–907 (2015).
Papa, A. & Pellegrino, S. Systematically Creased Thin-Film Membrane Structures. J. Spacecr. Rockets 45, 10–18 (2008).
Zirbel, S. A. et al. Accommodating thickness in origami-based deployable arrays. J. Mech. Des. 135, 111005 (2013).
Mahadevan, L. Self-Organized Origami. Science 307, 1740–1740 (2005).
Couturier, E., Courrech du Pont, S. & Douady, S. The filling law: A general framework for leaf folding and its consequences on leaf shape diversity. J. Theor. Biol. 289, 47–64 (2011).
Lang, R. J. & Hayes, B. Paper Pentasia: An Aperiodic Surface in Modular Origami. Math. Intell. 35, 61–74 (2013).
Lang, R. J. A Computational Algorithm for Origami Design. In ACM: Proceedings of the Twelfth Annual Symposium on Computational Geometry. Philadelphia PA, USA. doi: 10.1145/237218.237249 (1996).
Dudte, L. H., Vouga, E., Tachi, T. & Mahadevan, L. Programming curvature using origami tessellations. Nat. Mater. 15, 583–588 (2016).
Zhou, X., Wang, H. & You, Z. Design of three-dimensional origami structures based on a vertex approach. Proc. R. Soc. Math. Phys. Eng. Sci. 471, 20150407 (2015).
Nojima, T. Origami modeling of functional structures based on organic patterns. Masters Thesis Grad. Sch. Kyoto Univ. Kyoto Jpn. (2002).
Gattas, J. M., Wu, W. & You, Z. Miura-Base Rigid Origami: Parameterizations of First-Level Derivative and Piecewise Geometries. J. Mech. Des. 135, 111011 (2013).
Wei, Z. Y., Guo, Z. V., Dudte, L., Liang, H. Y. & Mahadevan, L. Geometric Mechanics of Periodic Pleated Origami. Phys. Rev. Lett. 110, 215501 (2013).
Schenk, M. & Guest, S. D. Geometry of Miura-folded metamaterials. Proc. Natl. Acad. Sci. 110, 3276–3281 (2013).
Yasuda, H. & Yang, J. Reentrant Origami-Based Metamaterials with Negative Poisson’s Ratio and Bistability. Phys. Rev. Lett. 114, 185502 (2015).
Hanna, B. H., Lund, J. M., Lang, R. J., Magleby, S. P. & Howell, L. L. Waterbomb base: a symmetric single-vertex bistable origami mechanism. Smart Mater. Struct. 23, 94009 (2014).
Lee, D.-Y., Kim, J.-S., Kim, S.-R., Koh, J.-S. & Cho, K.-J. The deformable wheel robot using magic-ball origami structure. In ASME: Int. Design Engineering Technical Conf. and Computers and Information in Engineering Conf. Portland, Oregon, USA. doi: 10.1115/DETC2013-13016 (August 4–7, 2013).
Guest, S. D. & Pellegrino, S. The Folding of Triangulated Cylinders, Part I: Geometric Considerations. J. Appl. Mech. 61, 773–777 (1994).
Ma, J. & You, Z. Energy Absorption of Thin-Walled Square Tubes With a Prefolded Origami Pattern—Part I: Geometry and Numerical Simulation. J. Appl. Mech. 81, 11003 (2014).
Schenk, M. & Guest, S. D. Origami Folding: A Structural Engineering Approach. In Origami 5: Fifth International Meeting of Origami Science, Mathematics, and Education (eds Wang-Iverson, P., Lang, R. J. & Yim, M. ) 291–303 (CRC Press, 2011).
Lauff, C. et al. Differentiating Bending From Folding in Origami Engineering Using Active Materials. In ASME: Int. Design Engineering Technical Conf. and Computers and Information in Engineering Conf. Buffalo, New York, USA. doi: 10.1115/DETC2014-34702 (August 17–20, 2014).
Lechenault, F., Thiria, B. & Adda-Bedia, M. Mechanical Response of a Creased Sheet. Phys. Rev. Lett. 112, 244301 (2014).
Tachi, T. Rigid Foldable Thick Origami. In Origami 5: Fifth International Meeting of Origami Science, Mathematics, and Education (eds Wang-Iverson, P., Lang, R. J. & Yim, M. ) 253–263 (CRC Press, 2011).
Ku, J. S. & Demaine, E. D. Folding Flat Crease Patterns With Thick Materials. J. Mech. Robot. 8, 31003 (2016).
Hoberman, C. Folding structures made of thick hinged sheets. United States patent US7, 794, 019 B2 (2010).
Chen, Y., Peng, R. & You, Z. Origami of thick panels. Science 349, 396–400 (2015).
Silverberg, J. L. et al. Origami structures with a critical transition to bistability arising from hidden degrees of freedom. Nat. Mater. 14, 389–393 (2015).
Bende, N. P. et al. Geometrically controlled snapping transitions in shells with curved creases. Proc. Natl. Acad. Sci. 112, 11175–11180 (2015).
Filipov, E. T., Tachi, T. & Paulino, G. H. Origami tubes assembled into stiff, yet reconfigurable structures and metamaterials. Proc. Natl. Acad. Sci. 112, 12321–12326 (2015).
Tachi, T. Designing freeform origami tessellations by generalizing Resch’s patterns. J. Mech. Des. 135, 111006 (2013).
Acknowledgements
This work is supported by the National Natural Science Foundation of China (No. 11472149) and the Tsinghua University Initiative Scientific Research Program (No. 2014z22074). X. C. acknowledges additional support from the National Natural Science Foundation of China (11172231, 11372241 and 11572238), Advanced Research Projects Agency-Energy (DE-AR0000396) and Air Force Office of Scientific Research (FA9550-12-1-0159).
Author information
Authors and Affiliations
Contributions
C.Q.C. initiated and guided the project. X.C. advised on the project. F.W. performed the analysis and experiments. H.G. contributed in part to the experiments. F.W., X.C. and C.Q.C. wrote the paper. All of the authors contributed to the research work.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Electronic supplementary material
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Wang, F., Gong, H., Chen, X. et al. Folding to Curved Surfaces: A Generalized Design Method and Mechanics of Origami-based Cylindrical Structures. Sci Rep 6, 33312 (2016). https://doi.org/10.1038/srep33312
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep33312
- Springer Nature Limited
This article is cited by
-
Experimental Approach of a Curved-Crease Folding Process with Multiple Folding Lines Applied on a Composite Material
Journal of Materials Engineering and Performance (2023)
-
Integration of origami and deployable concept in volumetric modular units
Scientific Reports (2022)
-
Recent development on innovation design of reconfigurable mechanisms in China
Frontiers of Mechanical Engineering (2019)
-
Twist of Tubular Mechanical Metamaterials Based on Waterbomb Origami
Scientific Reports (2018)
-
Creating Linkage Permutations to Prevent Self-Intersection and Enable Deployable Networks of Thick-Origami
Scientific Reports (2018)