Abstract
An electrostatic power generator converts mechanical energy to electrical energy by utilising the principle of variable capacitance. This change in capacitance is usually achieved by varying the gap or overlap between two parallel metallic plates. This paper proposes a novel electrostatic micro power generator where the change in capacitance is achieved by the movement of an aqueous solution of NaCl. A significant change in capacitance is achieved due to the higher than air dielectric constant of water and the Helmholtz double layer capacitor formed by ion separation at the electrode interfaces. The proposed device has significant advantages over traditional electrostatic devices which include low bias voltage and low mechanical frequency of operation. This is critical if the proposed device is to have utility in harvesting power from the environment. A figure of merit exceeding 10000(108μW)/(mm2HzV2) which is two orders of magnitude greater than previous devices, is demonstrated for a prototype operating at a bias voltage of 1.2 V and a droplet frequency of 6 Hz. Concepts are presented for large scale power harvesting.
Similar content being viewed by others
Introduction
There is a significant research effort focused on producing new higher efficiency and power density mechanical energy harvesting systems. Many small scale prototypes have been demonstrated and there is great potential that these concepts may in the future be realised for large-scale energy harvesting. To date, the three most widely investigated mechanical energy harvesting methods are based on: piezoelectric1,2,3,4,5, triboelectric6,7,8 and electrostatic9,10,11,12 principles. Piezoelectric and triboelectric generators are the most popular, with piezoelectric generators achieving power densities of 160 Wm−2 2 whilst triboelectric generators with power densities of 500 Wm−213 have been demonstrated.
Notwithstanding the exciting progress there are some major drawbacks that have hindered the progress of electrostatic generators. These include the requirement for high bias voltages, some as high as many hundreds of volts14,15,16, complex electrical circuits and high voltage device insulation required for safety in practical applications. The efficiency of devices can also be limited as they can usually only harvest vibrational or kinetic energy along a single axes of motion. The vibration frequencies required to achieve acceptable power harvesting are very high, usually in the order of a hundred Hz to kHz17,18,19 which makes them less than ideal for environmental power harvesting. In order to overcome these limitations a new and highly innovative electrostatic harvesting liquid electrode device was proposed in T. Krupenkin and J. A. Taylor20. Unfortunately the proposed liquid metal electrode was constructed from mercury which is a highly toxic with extensive evidence outlining mercury’s deleterious effects on human health and the environment.
Here we proposed a novel electrostatic generator that utilises a moveable liquid electrolytic dielectric. Although the use of a liquid dielectrics for energy generation have been recently reported21,22,23,24, here we propose a new ionic liquid dielectric device that not only takes advantage of the difference of dielectric constant of water versus air but also uses the free ions to generate a significantly larger capacitance change due to the formation of a Helmholtz double layer due to the bias voltage applied at the electrodes.
The ionic liquid electrolytic dielectric offers many desirable attributes including a flexible conformal material that is biocompatible, is abundant (sea water) and most importantly has a larger dielectric constant, much higher than air, resulting in higher energy harvesting capability. We further improve device performance by facilitating the sliding motion of the ionic fluid over the electrode surface by increasing surface hydrophobicity by depositing a thin layer TiO2 over the electrode surface. The proposed device has significant advantages over traditional electrostatic devices in term of cost, simplicity of fabrication, does not require any specific high cost packaging or vacuum shielding and is environmentally friendly. Importantly, the prototype device possess a very high surface charge density per conversion cycle of 3.8 mC/m2 and achieves a figure of merit exceeding10000(108μW)/(mm2HzV2), which is two orders of magnitude greater than previously reported devices.
This paper reports on the design, fabrication and characterisation of an ionic liquid dielectric power harvesting generator device. Potential applications of this device are described, including harvesting energy from droplets (raindrops), hydropower or water waves.
Principle of operation
Traditionally, electrostatic micro generator devices achieve changing capacitance by varying the gap or overlap area between two parallel plates of the capacitor. As shown in Fig. 1(a), the capacitance is maximized when the gap is smallest. In Fig. 1(b), when an external mechanical force is applied, the gap between the plates is increased resulting in reduced capacitance. If the voltage applied to the two terminals of the variable capacitor is fixed (by external sources such as a battery, a pre-charged capacitor or other active circuitry), the change in capacitance during this transition will generate an electric current as indicated in Fig. 1(c). The total amount of energy produced over a cycle is equal to25:
To increase the energy produced per cycle, a higher bias voltage or larger change in variable capacitance is required. In practice, it is difficult to achieve significant change in capacitance due to limited change in displacement of the solid plate electrodes. Therefore to increase generated power, higher bias voltages (VC), up to 1000 V14, are employed. This introduces many challenges. Our proposed device, while still based on the principle of variable capacitance, utilises the displacement of a liquid dielectric rather than solid electrodes. Figure 2(b) shows the main factors affecting geometric capacitance of the device; these include electrode length, width, spacing between electrodes, dielectric constant of substrate and medium above the electrodes. Analytical expression relating these geometric parameters to capacitance can be found in Van Gerwen, P. et al.26.
The addition of a hydrophobic oxide surface over the electrode facilitates droplet motion. As can be seen from Fig. 2(a,c), when the droplet is not over the surface of the electrodes, the capacitance is only due the interdigitated capacitance. This corresponds to the minimum capacitance value CMIN. Figure 2(d) illustrates the situation when droplet is fully covering the electrode area. At this stage, the device capacitance is at its maximum value CMAX. This change in capacitance is due to two factors. Firstly, the dielectric constant of the medium on top of the electrodes has increased significantly. For pure water at low frequency, its dielectric constant is approximately 78 times higher than that of the air27. Secondly, water droplets with dissolved salt (NaCl) contain charged ions. These ions accumulate at the interface of the metal electrodes and liquid electrolyte when a potential difference is applied. These layers of accumulated charge create an electrical double layer, which results in a significant, orders of magnitude, change in capacitance. Under a potential difference between two electrodes, positive ions are accumulated at the surface of negative electrode and negative ions are accumulated at the surface of positive electrode simultaneously. This capacitance due to charge separation can be modelled as a parallel plate capacitor with very small gap. An estimate of this capacitance can be obtained by28:
where S is the area of electrodes that interface with the solution and d is the effective thickness of the double layer. This dielectric layer thickness is referred as the Debye length. The major factors that affect the Debye length are ion concentration, ion charge and temperature. For a specific ion at a certain temperature, a higher ion concentration will result in a smaller Debye length. Figure 2(e) shows the schematic concept of this double layer effect and its equivalent electrical model. In this model, RSOL represents the series equivalent resistance of the double layer. This equivalent resistor also depends on ion concentration of the electrolyte, device geometry and temperature28.
Device fabrication and measurement setup
Device fabrication
The fabrication process of the liquid electrolyte generator involved the following steps:
Glass slides (Sail Brand) were used as the substrate layer and a quartz wafer was used to produce a mask. A thin film (100 nm) of Chromium (Cr) was deposited on the glass slides and on the quartz wafer by Electron beam evaporation (Inte vac Nanochrome II model). The lithographic features on the Cr coated quartz mask were produced using laser ablation (SUSS SLP300 model).
To pattern the interdigitated capacitor with finger width of 50 μm and finger gap of 10 μm, AZ1512HS resist was deposited on the slides, spun at 3000 rpm for 1 minute, resulting in a resist thickness of approximately 1.5 μm. The resist was exposed using the Cr coated quartz masks to UV light of 356 nm wavelength and power of 30 mWcm−2 for an exposure time of 15 seconds. After exposure, the sample was developed for 90 second using AZ712: H2O (3:2) developer and then rinsed with deionized water and dried using a nitrogen stream. The slide was then wet etched using a Cr etchant to define the metal interdigitated structure. The sample was then cleaned with acetone in an ultrasonic bath, rinsed with IPA and then dried with a nitrogen gun. In order to create the isolation between the metal fingers and the liquid dielectric, a layer of oxide was deposited. Kapton tape was used to cover the metal pads. A 10 nm layer of titanium dioxide (TiO2) was deposited using atomic layer deposition (ALD) method (Fiji F200 from Cambridge Nanotech). TiO2 was chosen instead of conventional SiO2 due to its inherit hydrophobicity29. An image of the fabricated device is shown in Fig. 3.
Measurement setup
Figure 4 shows the schematic of a constant voltage measurement setup for our proposed devices. Voltage across two terminals of the variable capacitor CVAR was fixed at VBIAS by using a voltage-clamp amplifier circuit. The charge stored on this variable capacitor is equal to:
Varying capacitance whilst keeping VBIAS fixed results in the generation of current IC. This current is measured using a trans-impedance amplifier which converts it to voltage using a resistor RG.
Results and Discussion
Constant voltage measurement using a patch clamp amplifier
Figure 5(a) illustrates a test setup used to verify the functionality of the device. The device was fixed at an angle of approximately 60°. A Kd Scientific micro pump was used to generate small droplets of 18 MΩ water. The patch clamp amplifier (Model MultiClamp 700B) was used to clamp the voltage and to monitor the generated current. As can be observed from Fig. 5(b), current is generated when the droplet slides over the device and there is negligible current generated after droplet had passed over the effective area of the device. Figure 5(c) represents a magnified section of the output current which illustrates the current generated when the droplet was passing through each of the 50 μm pair of finger. The magnitude of peak current is increased as the droplet’s speed is increased. As droplets travel across the fingers the peak current generated is plotted in Fig. 5(d). This graph indicates a strong inversely proportional relationship between the droplet sliding period and the amplitude of generated current. It is consistent with the equation that defines the generated current due capacitance change, which is equal to:
The effect of bias voltage on device performance was also investigated by varying the bias voltage whilst other test conditions, such as size of droplet and the speed of drop, were kept constant. The measurements were performed for three different bias voltages (0 mV, 80 mV and 160 mV). The measurements are shown in Fig. 6. As the bias voltage was increased, there was an increase in peak current generated confirming that the magnitude of current generated depends on the bias voltage.
A potential application of the device to large scale environmentally friendly energy harvesting
A promising application of this proposed device is for harvesting energy from liquid droplets. Liquid droplets are abundant in our environment. They can be freely available such as rain drops or can be easily formed in a marine environment by exploiting water wave or from a prefilled water reservoir. The concept of how water droplets are formed for practical applications is outlined in Fig. 7(b,c).
Figure 7(a) indicates details of an experimental setup for harvesting energy from the droplets. The energy harvesting device was placed at a distance of 450 mm below the drop generating tube. The bias voltage was set to be at 102 V. The gain-setting resistor was selected to be 1.8 MΩ. A micro pump was used to generate droplets. The flow rate was 6 mL per minute with an average of 6 droplets per second resulting in a drop volume of 16.7 μL. The droplet is on the surface of the device with an effective surface area of approximately 7 mm2.
Figure 8 summaries the experimental results. The generated current is shown in Fig. 8(a). Current generated from milliQ water droplets, which have very low ion concentration and droplets with 500 mM NaCl, which have similar concentration to seawater, are overlaid on the same graph for comparison. Current generated varies significantly depending on ion concentration. The peak current observed was approximately 2 μA for the 500 mM NaCl droplets. Figure 8(d) shows the corresponding current density per surface area of the device. The peak current density of approximately 250 mA/m2 is achieved for a 17 μL droplet of 500 mM NaCl. Comparison is shown in Table 1.
To estimate average energy and power generated, the charge generated over 10 s was integrated. This result is shown in Fig. 8(c). The average charge generated for milliQ and NaCl solution (500 mM) were 55 nC and 160 nC per second respectively. For droplets with 500 mM NaCl the equivalent surface charge density per conversion cycle is (160 nC)/(6 × 7 mm2) = 3.8 mC/m2. And the peak power density is 357 mWm−2 when operated at a bias voltage of 1.2 V. Although the output power (Fig. 8(b)) is lower compared to other electro-static generator devices it is important to emphasize that a much lower operating voltage is used here.
To evaluate and to compare device performance the figure of merit (FOM) proposed by Basset, P. et al.17 is used. This FOM is defined as:
where P is the converted power (in μW), VC is maximum voltage applied to variable capacitor (in V), f is operating frequency (in Hz) and S is device area (in mm2). The results, shown in Table 2, indicate that our proposed electrostatic generator has a two order of improvement over previous devices.
Future improvements
Our device possesses very high surface charge density per conversion cycle and there is a great potential for boosting the output power. Here we discuss on some key factors that affect the amount energy produced and how output power can be improved.
Electrolyte concentration
Equation (2) describes the principal factors that govern the amount of energy produced by a constant voltage electrostatic generator. At a certain bias voltage VBIAS, the produced energy is directly proportional to the capacitance change. From the model shown in Fig. 4(e), this capacitance change depends on geometric capacitance CIDC, double layer capacitance CDL and its equivalent series resistance RSOL. While electrolyte concentration has minimal effect on the geometric capacitance, it substantially affects CDL and RSOL. Hence a higher concentration electrolyte will create a larger overall capacitance change due to a decrease in RSOL and an increase in CDL.
Bias voltage
From equation(2), the amount of energy produced is directly proportional to . Hence an increase in VBIAS will significantly improve output power of the proposed device. If the bias voltage is increased to 24 V, which is 20 times higher than our test condition, the output power could increase by 400 times. However, a higher bias voltage requires a thicker insulation layer which will reduce the change in capacitance. To increase the bias voltage of the device while still maintaining the total capacitance change, a low dielectric constant and higher breakdown voltage material can be used.
Structural dimension and surface area of the device
Reducing electrode and gap dimensions and increasing the total surface area of the devices will also significantly increase the capacitance change, which leads to an increase in the produced energy and the output power. Currently, the prototype device has finger width of 50 μm and electrode gap of 10 μm. This dimension can be reduced to much smaller without increasing the complexity or the cost of fabrication process. Shim et al.30 recently has reported a cheap and reliable technique to produce large area interdigitated capacitor with gap between fingers is less than 500 nm using conventional lithography process. If the device dimension can be reduced to 2.5 μm finger width and 0.5 μm gap, the capacitance due to its geometry could be improved by 20 times. In addition, the fabrication process can be slightly modified to improve total surface areas of the device. Prior to deposition of metal on substrate, nano-imprinting can be used to increase nanoscale surfaces roughness. With nano-imprint technology, nano structuring with resolution smaller than 10 nm has been reported31. Assuming nano-imprint mould with pattern of 50 nm square and 100 nm height is deployed, for every 1 μm2 area, there will be 100 nano pattern and therefore the total new surface area will be (1 + 100 × 0.05 × 0.10 × 4 × 100 = 3 μm2), which is equivalent to three times increasing in total surface area. Both geometric capacitance (CIDC) and double layer capacitance (CDL) in equivalent model of Fig. 5(e) are dependent on the surface area of the device. Therefore, the total equivalent capacitance of the device will be significantly increased because of an escalation of the total surface area.
Contact time
By using nano-imprint to predefine surface roughness, the droplet contact angle will also be increased and the droplet sliding angle will be decreased32,33. This will lead to shorter contact time when droplet is on the device surface and hence the generated current will be increased.
Optimal load value
Further experimentation was carried out to investigate the effect of load on the power generated. Matching between the load and the device impedance will produce maximum output power. In this experiment, the load resistor was varied from 110 kΩ to 3.9 MΩ. MilliQ water(18 MΩ) droplets were used for this experiment, with a drip rate of approximately 7 droplets per second and bias voltage, applied on variable capacitor, was set at 2 V. Figure 9 summaries the test results. Figure 9(a) represents the total amount of charge generated over period of 5 second. Figure 9(b) shows the estimated average power generated from this generated charge. This result highlights that the output power of the device is load dependent. The output power for varying loads can differ by a factor of 5 times. Therefore, by carefully optimising the load condition, the output power of this generator can be substantially improved.
Conclusions
We have proposed a novel electrostatic power generator that converts mechanical energy to electrical energy by utilising movable ionic liquid electrolyte as the dielectric. This device offers many advantages over the traditional electrostatic generators. It exhibits large capacitance change due to the electrical double layer effect formed by ion separation and voltages applied at the electrodes and high dielectric constant of water. The achieved surface charge density and current density are favorable when compared to previous reported electrostatic generators. The fabrication process of this device only involves conventional lithography step which is cheap, scalable to macro size and does not require any high cost packaging or vacuum shielding. A peak current density of 250(mA)/(m2) and FOM of have been demonstrated for a prototype with the electrode width and gap of 50 μm and 10 μm respectively operating at 1.2 V and a droplet dropping rate of 6 Hz. The paper demonstrates a novel concept of an electrostatic generator device that can be used to harvest many widely available sources of (ionic) saline water droplets.
Additional Information
How to cite this article: Huynh, D. H. et al. Environmentally friendly power generator based on moving liquid dielectric and double layer effect. Sci. Rep. 6, 26708; doi: 10.1038/srep26708 (2016).
References
Chang, C., Tran, V. H., Wang, J., Fuh, Y.-K. & Lin, L. Direct-Write Piezoelectric Polymeric Nanogenerator with High Energy Conversion Efficiency. Nano Lett 10, 726–731 (2010).
Park, K. I. et al. Highly Efficient, Flexible Piezoelectric PZT Thin Film Nanogenerator on Plastic Substrates. Adv Mater 26, 2514–2520 (2014).
Lei, J. et al. Flexible piezoelectric nanogenerator based on Cu2O-ZnO pn junction for energy harvesting. RSC Adv 5, 59458–59462 (2015).
Siddiqui, S. et al. High-performance flexible lead-free nanocomposite piezoelectric nanogenerator for biomechanical energy harvesting and storage. Nano Energy 15, 177–185 (2015).
Mao, Y. et al. Sponge-Like Piezoelectric Polymer Films for Scalable and Integratable Nanogenerators and Self-Powered Electronic Systems. Adv Energy Mater 4, 1301624 (2014).
Zhang, H. et al. Triboelectric Nanogenerator for Harvesting Vibration Energy in Full Space and as Self-Powered Acceleration Sensor. Adv Funct Mater 24, 1401–1407 (2014).
Lin, Z.-H., Cheng, G., Lin, L., Lee, S. & Wang, Z. L. Water–Solid Surface Contact Electrification and its Use for Harvesting Liquid-Wave Energy. Angew Chem. 125, 12777–12781 (2013).
Lin, Z. H. et al. A multilayered interdigitative-electrodes-based triboelectric nanogenerator for harvesting hydropower. Nano Energy 15, 256–265 (2015).
Sakane, Y., Suzuki, Y. & Kasagi, N. The development of a high-performance perfluorinated polymer electret and its application to micro power generation. J. Micromech Microeng 18, 104011 (2008).
Despesse, G. et al. High Damping Electrostatic System for Vibration Energy Scavenging, Proceedings of the 2005 Joint Conference on Smart Objects and Ambient Intelligence: Innovative Context-aware Services: Usages and Technologies, New York, USA, pp. 283–286 (2005).
Jefimenko, O. D. & Walker, D. K. Electrostatic Current Generator Having a Disk Electret as an Active Element. IEEE Trans Ind Appl 14, 537–540 (1978).
Tada, Y. Experimental Characteristics of Electret Generator, Using Polymer Film Electrets. Jpn. J. Appl Phys 31, 846 (1992).
Wang, Z. L., Chen, J. & Lin, L. Progress in triboelectric nanogenerators as a new energy technology and self-powered sensors. Energy Environ Sci 8, 2250–2282 (2015).
Tsutsumino, T., Suzuki, Y., Kasagi, N. & Sakane, Y. Seismic Power Generator Using High-Performance Polymer Electret, 19th IEEE International Conference on Micro Electro Mechanical Systems, Istanbul, pp. 98–101 (2006).
Boland, J., Messenger, J., Lo, K. & Tai, Y. Arrayed liquid rotor electret power generator systems. 18th IEEE International Conference on Micro Electro Mechanical Systems, pp. 618–621 (2005).
Lo, H.-W., Whang, R. & Tai, Y.-C. A simple micro electret power generator. IEEE 20th International Conference on Micro Electro Mechanical Systems, pp. 859–862 (2007).
Basset, P. et al. A batch-fabricated and electret-free silicon electrostatic vibration energy harvester. J. Micromech Microeng 19, 115025 (2009).
Hoffmann, D., Folkmer, B. & Manoli, Y. Fabrication, characterization and modelling of electrostatic micro-generators. J. Micromech Microeng 19, 094001 (2009).
Yen, B. & Lang, J. H. A variable-capacitance vibration-to-electric energy harvester. IEEE Trans. Circuits Syst I 53, 288–295 (2006).
Krupenkin, T. & Taylor, J. A. Reverse electrowetting as a new approach to high-power energy harvesting. Nat Commun 2, 448 (2011).
Moon, J. K., Jeong, J., Lee, D. & Pak, H. K. Electrical power generation by mechanically modulating electrical double layers. Nat Commun 4, 1487 (2013).
Kwon, S. H. et al. An effective energy harvesting method from a natural water motion active transducer. Energy Environ Sci 7, 3279–3283 (2014).
Cheng, X., Meng, B., Han, M., Chen, H. & Zhang, H. A high-efficiency transparent electrification-based generator for harvesting droplet energy. 18th International Conference on Solid-State Sensors, Actuators and Microsystems (TRANSDUCERS), pp. 62–65 (2015).
Yin, J. et al. Generating electricity by moving a droplet of ionic liquid along graphene. Nat Nanotechnol 9, 378–383 (2014).
Boisseau, B. A. S. S. & Despesse, G. Electrostatic Conversion for Vibration Energy Harvesting. Intech (2012).
Van Gerwen, P. et al. Nanoscaled interdigitated electrode arrays for biochemical sensors. Sens Actuator B-Chem 49, 73–80 (1998).
Abeyrathne, C. D., Halgamuge, M. N., Farrell, P. M. & Skafidas, E. Dielectric properties of liquid phase molecular clusters using the external field method: molecular dynamics study. Phys Chem Chem Phys 16, 13943–13947 (2014).
Helmholtz, H. Ueber einige Gesetze der Vertheilung elektrischer Strme in krperlichen Leitern mit Anwendung auf die thierisch-elektrischen Versuche. Annalen der Physik 165, 211–233 (1853).
More, A. M., Gunjakar, J. L., Lokhande, C. D. & Joo, O. S. Fabrication of hydrophobic surface of titanium dioxide films by successive ionic layer adsorption and reaction (SILAR) method. Appl Surf Sci 255, 6067–6072 (2009).
Shim, J. S., Rust, M. J. & Ahn, C. H. A large area nano-gap interdigitated electrode array on a polymer substrate as a disposable nano-biosensor. J. Micromech Microeng 23, 035002 (2013).
Li, W.-D., Wu, W. & Williams, R. S. Combined helium ion beam and nanoimprint lithography attains 4 nm half-pitch dense patterns. J. Vac Sci Technol 30, 06F304 (2012).
Miwa, M., Nakajima, A., Fujishima, A., Hashimoto, K. & Watanabe, T. Effects of the Surface Roughness on Sliding Angles of Water Droplets on Superhydrophobic Surfaces. Langmuir 16, 5754–5760 (2000).
Yoshimitsu, Z., Nakajima, A., Watanabe, T. & Hashimoto, K. Effects of Surface Structure on the Hydrophobicity and Sliding Behavior of Water Droplets. Langmuir 18, 5818–5822 (2002).
Lin, Z.-H., Cheng, G., Lee, S., Pradel, K. C. & Wang, Z. L. Harvesting Water Drop Energy by a Sequential Contact-Electrification and Electrostatic Induction Process. Adv Mater 26, 4690–4696 (2014).
Ma, W., Zhu, R., Rufer, L., Zohar, Y. & Wong, M. An Integrated Floating Electrode Electric Microgenerator. J. Microelectromech Syst 16, 29–37 (2007).
Suzuki, Y., Edamoto, M., Kasagi,N., Kashwagi, K. & Morizawa, Y. Micro electret energy harvesting device with analogue impedance conversion circuit. Proc. PowerMEMS 8, 7–10 (2008).
Acknowledgements
This work was performed in part at the Melbourne Centre for Nanofabrication (MCN) in the Victorian Node of the Australian National Fabrication Facility (ANFF). We also would like to acknowledge Dr. Anh Trong Huynh, from DSTO, for his valuable discussions.
Author information
Authors and Affiliations
Contributions
D.H.H. and E.S. conceived and designed the experiments. D.H.H., T.C.N. and P.D.N. performed the experiments. D.H.H., E.S., T.C.N., C.D. Abeyrathne and M.S.H. analysed the data. E.S. and R.E. contributed materials/analysis tools. D.H.H., T.C.N., P.D.N. and E.S. wrote the manuscript. All authors discussed the results and commented on the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Huynh, D., Nguyen, T., Nguyen, P. et al. Environmentally friendly power generator based on moving liquid dielectric and double layer effect. Sci Rep 6, 26708 (2016). https://doi.org/10.1038/srep26708
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep26708
- Springer Nature Limited
This article is cited by
-
Laminated Structure of Al2O3 and TiO2 for Enhancing Performance of Reverse Electrowetting-On-Dielectric Energy Harvesting
International Journal of Precision Engineering and Manufacturing-Green Technology (2021)