Abstract
A dual-mode 3 dB power coupler based on silicon-on-insulator platform for mode division multiplexing system is proposed and demonstrated. The device, which consists of a tapered directional coupler and two output bend waveguides, has a 50:50 coupling ratio around the wavelength of 1550 nm for both fundamental and first order transverse magnetic (TM0 and TM1) modes. Based on asymmetrical tapered structure, a short common coupling length of ~15.2 μm for both modes is realized by optimizing the width of the tapered waveguide. The measured insertion loss for both modes is less than 0.7 dB. The crosstalks are about −14.3 dB for TM0 mode and −18.1 dB for TM1 mode.
Similar content being viewed by others
Introduction
Optical communication technology has made great strides for several decades and the capacity per fiber is gradually approaching the Shannon limit1. Fortunately, mode division multiplexing (MDM) provides a new dimension and it has been considered as a potential option to expand on-chip bandwidth by exploiting the high order modes of the multimode waveguides in recent years2,3. In order to realize a MDM system, many devices, including multiplexer4,5,6,7, amplifier8 and optical switching9,10, had been redesigned due to incompatibility with high order modes. The power coupler is an essential component in integrated optical communication systems and is widely used in many applications. However, the power coupler has mainly been achieved in single-mode communication networks and the efforts are focused on enhancing the bandwidth11,12,13,14,15,16,17,18 or realizing polarization independent11,14,19, while the investigations on multi-mode dimension have not been reported, to the best of our knowledge.
The simplest design for power coupler comprises of two parallel waveguides with a small gap17. According to the coupled-mode theory20, it can be extended to handle high-order mode through specifically designing the waveguides. Generally, the power coupler with symmetrical waveguide structure is sensitive to wavelength and coupling length. And it can be improved by employing the asymmetrical structure21,22. In this paper, we propose and demonstrate an on chip dual-mode 3 dB power coupler based on asymmetrical tapered two-waveguide structure. By optimizing the width of the tapered waveguide, the coupling length is chosen to be the least common 3 dB coupling length for dual modes and thus equal power splitting can be obtained. Benefitting from the asymmetrical tapered structure, the sensitivity of the coupling length for each mode is relaxed. In consequence, the proposed dual-mode 3 dB power coupler is compact in size and easy to fabricate. The characteristics of the coupler are investigated, both theoretically and experimentally. For demonstration, the coupler is fabricated on 220-nm-high silicon-on-insulator (SOI) platform. The measured insertion loss for both fundamental and first order transverse magnetic (TM0 and TM1) modes are less than 0.7 dB. The crosstalks are about −14.3 dB for TM0 mode and −18.1 dB for TM1 mode. The performance of the coupler indicates that it can operate on multiple modes and would find potential applications in on-chip high bandwidth communications.
Results
Principle and simulation
The schematic configuration of the proposed scheme is illustrated in Fig. 1. The straight coupling region consists of a uniform waveguide and a tapered waveguide to form an asymmetrical directional coupler. Here, the transverse magnetic (TM) mode is utilized. The widths of the two waveguides are designed to support TM0 and TM1 modes. In order to realize a 50:50 coupling ratio simultaneously, the common 3 dB coupling length of the two modes is selected to be the coupling length. The single-mode couplers based on symmetrical structure are sensitive to wavelength and the coupling length. Considering the high order modes, the sensitivity of wavelength and coupling length will be strengthened, resulting in the common coupling length for two modes will be very long and inapplicable for dual modes design. In our scheme, a tapered waveguide is utilized to alleviated the issue of wavelength sensitivity and relax the precision of coupling length13,22,23. As shown in Fig. 1(b), half energy is coupled from the input waveguide to another waveguide through the coupling region for TM0 and TM1 modes, resulting in 3 dB power splitting for both modes. The length of the coupling region is defined as L and other parameters are shown in Fig. 1(c). We use the multimode bend waveguides with radius R to separate the two output ports. The R is chosen to be 25 μm to avoid excess loss while not compromise the size of the device.
The schematic configuration and the geometric parameters of the proposed dual-mode 3dB power coupler.
(a) The 3-dimension structure and (b) topview of the proposed device. (c) The cross sections of the front (A) and the end (B) of the coupling region in (b). (d) The simulated effective indices of TM0 mode and TM1 mode associated with different waveguide widths at 1550 nm.
In the simulation, the width of the uniform waveguide w1 is chosen to be 1 μm, which can stably support the TM1 mode. The gap between the two waveguides is fixed to be 200 nm. The coupling length L, which is the least common 3 dB coupling length of the two modes, is determined based on the optimized result of waveguide width. The width w2 is supposed to be w1 − Δw while w3 is w1 + Δw. The effective index of TM0 mode is almost invariable when the waveguide is tapered around 1 μm, while the one of TM1 mode is dramatically changed, as indicated in Fig. 1(d). Therefore, the tapered directional coupler can be regarded as a conventional coupler for TM0 mode but a tapered asymmetrical coupler for TM1 mode. Hence, the coupling length L can be set as the 3 dB coupling length of TM0 roughly and Δw is optimized to mainly adjust the 3 dB coupling length of TM1 mode, targeting to obtain a short common 3 dB coupling length. Considering the two modes simultaneously, the finally optimized width of tapered waveguide varies from w2 = 0.93 μm to w3 = 1.08 μm. The optimized coupling length L is 15.2 μm. The final results are presented as the red and green curves in Fig. 2. It is worth noting that the transmission spectra of both modes are almost the same and the coupling ratios are around 50:50 at the wavelength of 1550 nm. The simulated insertion losses of both modes are lower than 0.1 dB which can be neglected. The transmission spectra of conventional symmetrical directional couplers are calculated as a contrast, as shown by blue and pink dash curves in Fig. 2(a,b). One can find that, the coupling ratio dependency on wavelength of our scheme is slightly improved in the case of TM0 mode input and the improvement for TM1 mode is obvious. The difference is accessible because the tapered asymmetrical structure mainly works on TM1 mode. Figure 3(a,b) present the electric field distributions of TM0 and TM1 modes along the propagation direction at 1550 nm respectively, while the inserts are the mode distributions of the input and two output ports. The input TM0 and TM1 modes are evenly divided around the point of L = 15.2 μm. The inserts show that the output mode is the same with the input mode, qualitatively indicating a low crosstalk. Additionally, we utilize the mode expansion method to quantitatively calculate the crosstalk of the whole coupler with the output bend waveguides. The simulated results are shown in Fig. 4. The crosstalks, defined as the ratio of the sum of the interfering mode power to the desired mode power, are −17.0 dB for TM0 mode and −18.9 dB for TM1 mode. The higher crosstalk of TM0 might be caused by the multimode bend waveguides24,25, which would introduce a crosstalk in transmission and can be reduced by increasing the radius or special design. As mentioned previously, the performance of the directional-coupler-based device is sensitive to geometric parameters. The fabrication tolerances to the deviations of coupling length, waveguide width and gap are investigated, as shown in Fig. 5. The same calculations for conventional scheme are also presented as references. Results indicate improvement on the fabrication tolerance compared with the conventional coupler.
Simulated transmission spectra of our scheme compared with the conventional coupler.
The results of (a) TM0 mode and (b) TM1 mode input. The conventional coupler for TM0 consists of two strip waveguides whose widths are 1.0 μm and heights are 220 nm. The gap between the two waveguides is 200 nm. The parameters for TM1 is the same except the coupling length.
Experimental results
Figure 6(a) shows the scanning electron micrograph (SEM) of the fabricated structure. Due to the lack of TM1 source and other necessary facilities for high order mode, an extra mode multiplexer is designed for TM1 signal inputting and another mode demultiplexer is utilized for output TM1 measurement. The input TM0 mode from Input 1 (marked in Fig. 6(a)) is converted to TM1 mode by the multiplexer and then the converted TM1 mode divides evenly into the two output waveguides, which are finally converted to TM0 modes and coupled out from the Output 1 and Output 3, respectively. On the other hand, the input TM0 mode from the Input 2 propagates straightly to the 3 dB coupler and couples out from the Output 2 and Output 4 after division. In order to calibrate the insertion loss of the device we designed, a referenced MDM structure including a mode multiplexer and a demultiplexer is also fabricated, as shown in Fig. 6(b). The detailed SEM of the mode multiplexer is shown in Fig. 6(c). The mode multiplexer is based on asymmetrical directional coupler. The TM0-TM1 coupling relies on the phase matching between the waveguides, which means that the effective index of the TM0 mode of the narrow waveguide should be equal to that of the TM1 mode of the wide waveguide. The optimized width of the single-mode and multimode waveguides are 0.5 μm and 1.23 μm respectively, while the coupling length is 9.5 μm. Figure 6(d) shows the detail of the fabricated dual-mode 3 dB power coupler. The focusing grating couplers are used to couple TM0 mode into and out of the chip26,27.
To evaluate the performance of the proposed device, a broadband light source assisted by the polarization controller and an optical spectrum analyzer (OSA) are used to measure the transmission spectra of the device. Figure 7(a) presents the measured coupling efficiency of the grating coupler. The coupling loss is about 4.3 dB for one port at 1550 nm. The experimental results of the mode multiplexer are shown in Fig. 7(b). The excess losses are about 0.2 dB and 2.1 dB for TM0 and TM1 mode channels, respectively. Low crosstalks of −25 dB for the two mode channels are observed. The average transmission spectra of TM0 and TM1 are shown in Fig. 8(a,b), respectively. The insertion loss introduced by the coupling gratings and the MDM structure have been deducted. The experimental results almost conform to the simulated ones shown in Fig. 2(a,b). The insertion loss of the TM0 mode is ~ 0.7 dB, while the one of TM1 mode is ~0.2 dB. The difference is caused by the inconformity between the MDM structure used in the test structure and the referenced one, owing to the imperfect fabrication. The measured crosstalks for TM0 and TM1 transmissions are −14.3 dB and −18.1 dB, respectively.
The performance of the referenced grating coupler and MDM structure.
(a) The measured coupling efficiency of the grating coupler. (b) The experimental results of the mode multiplexer. The definitions of the MDM ports are marked in Fig. 6(b).
Discussion
In conclusion, we propose and design an on-chip dual-mode 3dB power coupler using an asymmetrical directional coupler built on the SOI platform. The device can be easily fabricated in a single step of exposure and etching. Simulated and experimental results show an even division for both TM0 and TM1 modes at the wavelength of 1550 nm, with insertion losses of about 0.7 dB and 0.2 dB. The measured crosstalks for TM0 and TM1 modes are about −14.3 dB and −18.1 dB, respectively. The fabrication tolerances to the deviations of coupling length, waveguide width and gap are also discussed and the results show improvement compared with the conventional coupler. The coupler can accommodate the mode division multiplexed system and would be applied in future silicon based large capacity communication systems.
Methods
Simulation method
We use a three-dimension finite difference time domain (FDTD) method to simulate the proposed dual-mode 3 dB coupler. In order to save the simulation time, we firstly optimize the performance of the coupler without the two bend waveguides to obtain the rough parameters. It is to be noted that, there is still a small coupling in the bend region, which is not considered in the simulation. So in the next step, we optimize the performance of the whole coupler by making a small change around the rough parameters.
Device fabrication and experimental method
The device is fabricated utilizing 248 nm deep ultraviolet photolithography and inductively coupled plasma (ICP) etching using SOI wafer with top silicon layer of 220 nm and silicon dioxide (SiO2) substrate of 2 μm. The etched structures have a SiO2 cladding layer by utilizing plasma-enhanced chemical vapor deposition. Due to the lack of TM1 source and other necessary facilities for high order mode, an extra mode multiplexer is designed for TM1 signal inputting and another mode demultiplexer is utilized for output TM1 measurement. In order to calibrate the insertion loss of the device we designed, a referenced MDM structure including a mode multiplexer and a demultiplexer is also fabricated. Since the results are easily disturbed by a lot of factors, we test the device many times and average the results, aiming to reduce the measuring error and alleviate the influence introduced by environment.
Crosstalk calculation
We employ the mode expansion method to analyze the crosstalk of the dual-mode power coupler in the simulation. The mode expansion method is to calculate the power proportion of each mode inside one waveguide based on overlap integral, as explained by following formula:
![](http://media.springernature.com/lw336/springer-static/image/art%3A10.1038%2Fsrep23516/MediaObjects/41598_2016_Article_BFsrep23516_Equ1_HTML.gif)
where the is the input mode field and the
is a set of modes that the waveguide supports.
Additional Information
How to cite this article: Luo, Y. et al. Integrated dual-mode 3 dB power coupler based on tapered directional coupler. Sci. Rep. 6, 23516; doi: 10.1038/srep23516 (2016).
References
Essiambre, R., Kramer, G., Winzer, P. J., Foschini, G. J. & Goebel, B. Capacity Limits of Optical Fiber Networks. J. Lightwave Technol. 28, 662–701 (2010).
Uematsu, T., Ishizaka, Y., Kawaguchi, Y., Saitoh, K. & Koshiba, M. Design of a Compact Two-Mode Multi/Demultiplexer Consisting of Multimode Interference Waveguides and a Wavelength-Insensitive Phase Shifter for Mode-Division Multiplexing Transmission. J. Lightwave Technol. 30, 2421–2426 (2012).
Richardson, D. J., Fini, J. M. & Nelson, L. E. Space-division multiplexing in optical fibres. Nature Photon. 7, 354–362 (2013).
Wang, J., Chen, P., Chen, S., Shi, Y. & Dai, D. Improved 8-channel silicon mode demultiplexer with grating polarizers. Opt. Express 22, 12799–12807 (2014).
Ye, M., Yu, Y., Zou, J., Yang, W. & Zhang, X. On-chip multiplexing conversion between wavelength division multiplexing-polarization division multiplexing and wavelength division multiplexing-mode division multiplexing. Opt. Lett. 39, 758–761 (2014).
Luo, L. W. et al. WDM-compatible mode-division multiplexing on a silicon chip. Nature Commun. 5, 3069 (2014).
Dai, D. In Asia Communications and Photonics Conference. (Optical Society of America).
Kang, Q. et al. In Fiber-Based Technologies and Applications. FTh4F. 1 (Optical Society of America).
Diamantopoulos, N. P. et al. Mode-selective optical packet switching in mode-division multiplexing networks. Opt. Express 23, 23660–23666 (2015).
Stern, B. et al. On-chip mode-division multiplexing switch. Optica 2, 530 (2015).
Hsu, S. H. Signal power tapped with low polarization dependence and insensitive wavelength on silicon-on-insulator platforms. J. Opt. Soc. Am. B 27, 941–947 (2010).
Kishioka, K. A design method to achieve wide wavelength-flattened responses in the directional coupler-type optical power splitters. J. Lightwave Technol. 19, 1705–1715 (2001).
Yun, H., Shi, W., Wang, Y., Chrostowski, L. & Jaeger, N. A. F. 2 × 2 Adiabatic 3-dB Coupler on Silicon-on-Insulator Rib Waveguides. Proceedings of SPIE-The International Society for Optical Engineering (2013).
Chen, B. X., Lu, H. L., Zhao, D. X., Yuan, Y. F. & Iso, M. Optimized design of polarization-independent and temperature-insensitive broadband optical waveguide coupler by use of fluorinated polyimide. Appl. Opt. 42, 4196–4201 (2003).
Lu, Z. et al. Broadband silicon photonic directional coupler using asymmetric-waveguide based phase control. Opt. Express 23, 3795 (2015).
Cong, G. W. et al. Demonstration of a 3-dB directional coupler with enhanced robustness to gap variations for silicon wire waveguides. Opt. Express 22, 2051–2059 (2014).
Alam, M. Z., Caspers, J. N., Aitchison, J. S. & Mojahedi, M. Compact low loss and broadband hybrid plasmonic directional coupler. Opt. Express 21, 16029–16034 (2013).
Caspers, J. N. & Mojahedi, M. Measurement of a compact colorless 3 dB hybrid plasmonic directional coupler. Opt. Lett. 39, 3262–3265 (2014).
Luo, Y., Ye, M., Yu, Y. & Zhang, X. In Asia Communications and Photonics Conference 2015. ASu2A.26 (Optical Society of America).
Huang, W.-P. Coupled-mode theory for optical waveguides: an overview. J. Opt. Soc. Am. A 11, 963–983 (1994).
Takagi, A., Jinguji, K. & Kawachi, M. Design and fabrication of broad-band silica-based optical waveguide couplers with asymmetric structure. IEEE J. Quantum Electron 28, 848–855 (1992).
Takagi, A., Jinguji, K. & Kawachi, M. Wavelength characteristics of (2×2) optical channel-type directional couplers with symmetric or nonsymmetric coupling structures. J. Lightwave Technol. 10, 735–746 (1992).
Wang, J. et al. Broadband and fabrication-tolerant on-chip scalable mode-division multiplexing based on mode-evolution counter-tapered couplers. Opt. Lett. 40, 1956 (2015).
Gabrielli, L. H., Liu, D., Johnson, S. G. & Lipson, M. On-chip transformation optics for multimode waveguide bends. Nature Commun. 3, 1217 (2012).
Dorin, B. A. & Ye, W. N. Two-mode division multiplexing in a silicon-on-insulator ring resonator. Opt. Express 22, 4547 (2014).
Van Laere, F. et al. Compact focusing grating couplers for silicon-on-insulator integrated circuits. IEEE Photon. Technol. Lett 19, 1919–1921 (2007).
Wang, J., Chen, P., Chen, S., Shi, Y. & Dai, D. Improved 8-channel silicon mode demultiplexer with grating polarizers. Opt. Express 22, 12799–12807 (2014).
Acknowledgements
This work was supported by the National Natural Science Foundation of China (Grant No. 61475050 and 61275072) and the New Century Excellent Talent Project in Ministry of Education of China (NCET-13-0240).
Author information
Authors and Affiliations
Contributions
Y.C.L. proposed the study. Y.C.L. and Y.Y. analyzed the results and wrote the manuscript. Y.Y. and X.L.Z. supervised the project and edited the manuscript. All authors discussed the results and commented on the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Luo, Y., Yu, Y., Ye, M. et al. Integrated dual-mode 3 dB power coupler based on tapered directional coupler. Sci Rep 6, 23516 (2016). https://doi.org/10.1038/srep23516
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep23516
- Springer Nature Limited
This article is cited by
-
Subwavelength silicon photonics for on-chip mode-manipulation
PhotoniX (2021)
-
Nonvolatile and ultra-low-loss reconfigurable mode (De)multiplexer/switch using triple-waveguide coupler with Ge2Sb2Se4Te1 phase change material
Scientific Reports (2018)
-
Silicon chip-scale space-division multiplexing: from devices to system
Science China Information Sciences (2018)