Abstract
There are several productive petroleum fields in the North Western Desert (WD) of Egypt, which received extensive investigations regarding their petroleum potential. However, a few studies tackled the Matruh Oil Field, which contains the oil prolific Early Cretaceous Alam El-Bueib Formation (AEB Fm) reservoir. The reservoir intervals of the AEB Fm show substantial lithological variations across the basin. Therefore, it is necessary to analyze the vertical and lateral distributions in terms of their lithological and petrophysical properties. To achieve this objective, wireline logs of four wells and 20-2D seismic lines were used to construct a depth-structure contour map for the studied part of the field. This map was used to build the field’s structure model and to identify the fault patterns in the basin through several seismic lines. Analyses of well logs data and lithology were used to estimate the petrophysical properties of AEB sandstone units AEB-1, AEB-3A, AEB-3C, and AEB-6. Results show that the AEB-6 Unit is the most promising hydrocarbon-bearing unit. It has a net pay of 20–160 feet, a shale volume of 5–20%, an effective porosity of 14–20%, and a hydrocarbon saturation of 70–88%. The structure-depth maps indicate a number of normal faults with two principal NE-SW and NW–SE trends, which probably act as structural traps in the Matruh Oil Field. The constructed structure-depth maps and calculated petrophysical parameters were used to build a three-dimensional reservoir model. A blind well was used to validate the accuracy and reliability of the facies, porosity, and saturation models for the AEB Fm units, ensuring a good match between log-derived data and built models. The AEB Fm shows regional heterogeneous variations in its petrophysical characteristics. It exhibits unconventional reservoir characteristics in a N–S direction and conventional reservoir characteristics in an E–W direction. This observed heterogeneity shows the need to carry out further investigations to comprehensively assess the hydrocarbon potential of AEB Fm in different areas of the Matruh Basin.
Similar content being viewed by others
Introduction
Since global oil demand is rising, it is expected to surpass pre-pandemic levels, reaching 101.6 million barrels per day (BPD) in 20231. Boosting the hydrocarbon supply to meet that demand is essential. To increase the supply of oil, exploration and production processes should be conducted with caution. More attention should be paid to oil field exploration having potential reservoirs. One of the significant contributors to Egypt’s oil production is the northern region of the Western Desert. The Matruh Basin exploration area has 23 billion barrels of oil equivalent (BBOE) with a low risk of hydrocarbon accumulation2. The Matruh Basin is situated in the northern region of the Western Desert (Fig. 1) and has a substantial hydrocarbon system of Cretaceous origin, making it one of the most significant petroliferous areas in northern Egypt3,4. The Matruh Oil Field, the focus of this study is situated within the middle Matruh Basin at latitudes 30° 55′ 41″ and 30° 57′ 37″ N, and longitudes 27° 23′ 18″, 27° 25′ 18″ E (Fig. 1)5. The Matruh Field (Fig. 1A) is approximately 28.47 km2 and is located 45 km southeast of Matruh Town. The Matruh Field was discovered in 1991, when the Matruh 1-1 well was drilled and the logs showed hydrocarbon-bearing sandstone reservoirs of the Middle Jurassic Khatatba Formation. The maximum oil production from the Western Desert is derived from its northern basins, particularly the Matruh Basin, of which 70% comes from the Jurassic and Cretaceous sandstone reservoirs6.
(A) Location map of the Matruh-Shushan Basin in the Western Desert, showing the main Mesozoic basins and study area of Matruh Field (blue rectangular) (B) The enlarged area shows the pattern of structures and main faults in the Matruh and Shushan Basins, North Western Desert, Egypt, and the location of the studied wells (C) Location map of the studied wells in Matruh Field within seismic lines and the location of the validation well (Apidose-1X) for modeling. (This figure is modified after7, Copyright
Although several publications investigated the hydrocarbon potential of the Middle Jurassic Khatatba and Lower Cretaceous Alam El-Bueib formations in the northern part of WD, including2,7,8,9,10,11,12,13,14,15,16,17,18,19,20, just a few studies15,21,22,23,24 focused on the Matruh Basin. Only three published studies dealt with the structural modelling of potential traps and/or reservoir quality of the Alam El-Bueib Formation in the Matruh Basin. The first study focused on the fault systems in the Jade Oil Field in western Matruh Basin25 and suggested that the main structural trap is an anticlinal fold that was moving in a NE-SW direction along a reversed fault. They suggested that this fault was developed during the Jurassic period and was rejuvenated and reversed during the Late Cretaceous regional basin inversion.
This was probably related to the Tethyan rifting and NE drifting of the African plate towards the Eurasian plate19, which caused major uplifting and basin inversion of multiple regions in the northwestern area of Egypt, such as the Matruh Basin. The second study focused on assessing the reservoir and source potential of the Alam El-Bueib Formation through a single well26. The authors reached a conclusion that the Alam El-Bueib Formation exhibits important reservoir characteristics and lower source rock potential. They identified four main reservoir intervals made up of sandstones and carbonates, where clastic units show significant variations in the shale volume (6.5–56.1%). These reservoirs possess fair to good porosity characters (4.0–7.1%), varying water saturation (11.3–84.4%) and low to good hydrocarbons saturation (11.3–88.7%) values. The third study focused on the reservoir quality of the Alam El-Bueib Formation through four wells in the Jade Oil Field22. This study suggested that the sandstones of the AEB-3G and AEB-6 members are good reservoirs. They show good porosity (12.5–16%), high hydrocarbon saturation (up to 80%), and fair movable hydrocarbon volumes (up to 15%), but with varying water saturation values (4–22%) and shale volumes (8–14%). This study suggested that the AEB-3G and AEB-6 members of the Alam El-Bueib Formation have actual hydrocarbon accumulations. Furthermore, the intra- and inter-basinal stratigraphic correlations along the Matruh Basin and its adjacent Shushan Basin indicate that the Alam El-Bueib Formation shows evident lateral and vertical facies changes27. This indicates that the reservoir quality of the Alam El-Bueib Formation is affected by volume and vertical/lateral distributions of shale deposits almost along the entire formation on local and regional scales in the Matruh Basin.
Overall, the above-mentioned studies show that different parts of the Matruh Basin exhibit different vertical/lateral facies and petrophysical characteristics and possess various structural traps of different styles. This indicates that the reservoir potential of the Lower Cretaceous Alam El-Bueib Formation is still underexplored in the Matruh Basin. Therefore, the current work was designed to shed more light on the reservoir potential of the Alam El-Bueib Formation in another petroleum productive area of the Matruh Basin. To the best of our knowledge, this research study is the initial examination conducted on a regional level, in which many wells were utilized to assess the reservoir quality of the Alam El-Bueib Formation in the Matruh Oil Field. This was achieved by constructing a depth-structure contour map for the Matruh Field using 2D seismic data and wireline logs of four wells. In addition, the identification of the fault patterns penetrating the basin was made using seismic data interpretation. Analysis of well logs data was also made to recognize the lateral and vertical variations in the lithological and petrophysical parameters of the AEB Formation’ units (AEB-1, AEB-3A, AEB-3C, and AEB-6). This was supplemented with an analysis of the Rock–Eval data to assess the reservoir and source rock potential of shaly sandstone facies within the AEB Formation.
The geological settings
The Matruh Basin lies between longitudes 26° and 27° 30' E and 31° and latitudes 31° 17' N3,18,19,20 and represents a part of the unstable tectonic realm, which encompasses the entire northern part of Egypt including the North Western Desert of Egypt. The Mesozoic tectonic activities in the North Western Desert region resulted in the formation of several basins, where depositional history of the Mesozoic sedimentary successions were mainly affected by these tectonics. The trapped hydrocarbon accumulations are largely connected to the Jurassic and Cretaceous tectonostratigraphic evolution of the Matruh Basin. This evolution resulted in the formation of several reservoir and seal systems. The tectonic evolution of northern Egypt indicates three main tectonic events10,12 (Fig. 2).
The first event resulted in the formation of the Paleozoic-Early Mesozoic (Triassic) fault with a NW to WNW trend. The second event took place during the Late Mesozoic (Late Cretaceous) and resulted in the formation of a ENE-trending series of faulted anticlines commonly known as the “Syrian Arc System”19,28. The third event occurred during the Early Paleogene (Late Eocene and Early Oligocene) and formed the NW-trending Gulf of Suez and NNE-trending Aqaba faults. Several investigations of the tectonic evolution of the sedimentary basins along with their stratigraphic history in the North Western Desert were made by the following authors11,16.
The majority of the petroleum fields in the Western Desert of Egypt including the Matruh Basin is associated with systems developed in the Late Cretaceous–Eocene and is located in or near the basin depocenters, which later became petroleum productive areas17. The Matruh Basin was initially developed during the Permian through Triassic times as a part of a large continental basin comprising the Shushan-Matruh Basin29. The Jurassic Tethyan rifting and drifting of the northern African plate towards the European plate resulted in the formation of the Matruh Basin along with other numerous rift basins18,30. Subsequently, at the end of Late Cretaceous, the collision of the African/Arabian and Eurasian plates produced compressive forces, which caused uplifting, folding, and basin inversion of large parts of the North Western Desert and formed the Syrian Arc System. These tectonic events resulted in the formation of faults and folds of NNE to SSW trends, which are dissected by normal faults of NW to SE trends (Fig. 1B). These fold systems are important petroleum structural traps for example in the Obaiyed, Jade, and Matruh fields25.
Lithostratigraphy
The Matruh Basin has a sedimentary cover of nearly 14,000 ft (4267.2 m)31, which spans a wide range from the Cambrian to the Miocene (Fig. 2). The Matruh Basin has four main sedimentary cycles that controlled its sedimentation and are separated by regional unconformities32,33. The first cycle occurred throughout the Early to Middle Jurassic, which represents Ras Qattara and Yakout formation’s fluvial-lacustrine sediments and the Khatatba and Masajid formation’s deltaic and shallow marine sediments. The second cycle occurred in the latest Early to earliest Late Cretaceous (Albian–middle Cenomanian) and represents the fluvial-delta to shallow marine sediments of the following formations: Alam El-Bueib, Alamein, Dahab, Kharita, and Bahariya. The third cycle occurred in the Late Cretaceous (late Cenomanian–Campanian) and represents the Abu Roash open marine shale and the Khoman carbonates. The fourth cycle occurred during the late Paleogene and early Neogene periods (Eocene–Miocene) and represents the Apollonia, Dabaa, Moghra, and Marmarica formations open marine shale and carbonates34,35 (Fig. 2).
Stratigraphic column showing the formations and their lithology encountered in the Western Desert of Egypt (Modified from33).
The Lower Cretaceous rock successions can be separated into four major formations of a shallow marine origin; these are the Alam El-Bueib, Alamein, Dahab, and Kharita33. The Alam El-Bueib Fm, which lies beneath the Alamein Dolomite and overlies the Masajid Formation, is mostly made up of sandstones, with minor amounts of siltstones, and shales with thin dominant limestone and dolomite, carbonate, beds. The thickness of the Alam El-Bueib Fm is large and contains six unconformable clastic rocks units, which were deposited above the Upper Jurassic marine carbonates of the Masajid Formation34,35,36,37,38.
Materials and methods
Materials
The data utilized in this study was obtained from Khalda Petroleum Company (KPC), with authorization granted by the Egyptian General Petroleum Corporation (EGPC). The dataset consists of well logs from four wells, namely Matruh 1-1, Matruh-5, Matruh-6, and Samaa-1X, which are distributed in the study area. These logs include “Gamma ray, Resistivity, Caliper, Neutron, Density, Photo Electric Factor, Density Environmental Correction, Acoustic logs, and Reservoir Pressure data. Reservoir pressure data (RFT) for three wells (Matruh-5, Matruh-6 and Samaa-1X) were available to be used in determining the reservoirs fluids behavior. Geochemical pyrolysis data (S1, S2, S3, Tmax, and PI) of 15 ditch samples from the AEB-6 Unit of the AEB Fm was available from the Matruh 1-1 well in the Matruh Oil Field (Table 1).
The provided data sets include also a two-dimensional survey of seismic reflection data (Fig. 1C) and a check-shot surveys in two wells (Matruh-5 and Matruh 1-1), which were used in constructing the structure depth map as an input for the reservoir modeling.
Methodology
Source rock evaluation
The remaining hydrocarbon potential (S2) value was measured in mg HC/g rock, which represents the quantity of the hydrocarbons that can be produced via thermal cracking of the enclosed kerogen at a Tmax temperature range of (300–550 °C). It indicates the capability of the rock to generate hydrocarbons. S2 decreases with increasing maturity level giving false estimates of the source potential of the mature samples. Therefore, based on38 concept, the source generating potential in a mature rock should be corrected by adding the generated free HC (S1) to the remaining (S2) to give the original generating capacity (Genetic Potential: GP). The term used to denote the maximum temperature at which the highest rate of hydrocarbon generation (S2) occurs is called Tmax temperature, which is used as a maturity measure and it increases with increasing levels of maturity of organic matter. Caution should be taken with Tmax data, because the mineral matrix effect has the potential to suppress the Tmax values of bulk rock samples38.
Seismic interpretation
The seismic data given from the Khalda Petroleum Company (KPC) is in the form of 2D seismic data that has previously undergone shift correction, guaranteeing precise alignment. The ultimate goal of this work is to detect hydrocarbon accumulations, delineate their extent, and calculate their volumes. Therefore, seismic interpretation was based on picking and tracking laterally extended seismic reflectors for mapping geologic and stratigraphic features, and also for determining reservoir architecture25,39,40,41. Petrel software 2017.3 version was used in all geological and geophysical data integration to interpret the seismic data and to generate maps. The primarily step in the seismic interpretation was to apply the technique of seismic to well tie. The main purpose of this technique was to make a tie between seismic data (in time) and well data, formation tops, (in-depth) to find (seismic reflections). According to36, seismic data and geological features can be tied by applying two methods. Firstly, by creating a time-depth relationship using the check shot data (Fig. 3), which is a simple method but is less accurate. Secondly, by creating a synthetic seismogram (Fig. 4) using the formation velocity (i.e., sonic logs) and formation density (i.e., density logs) over the intervals of interest in the Matruh 1-1, and Matruh-5 wells. Before applying both methods, we made a quality control (Q.C.) on the available check shot data of the two wells on petrel and removed any outliers from them as presented in (Fig. 3). In the current study, we used the check shot survey of the Matruh 1-1 and Matruh-5 wells to connect the formation tops of the drilled wells in the field to the seismic section traveling through or near these wells (Figs. 4 and 5).
Synthetic seismogram at the Matruh-5 well, the Matruh Field at Matruh Basin (generated in Petrel ™ Schlumberger 2017.3 software, https://www.software.slb.com/).
Synthetic seismogram at the location of Matruh-1-1 well, the Matruh Basin (generated in Petrel ™ Schlumberger 2017.3 software, https://www.software.slb.com/).
Any discrepancy between the generated synthetic seismogram and the seismic data were reduced by time-shifting methods used by42,43 or by changing in the wavelet phase constant used to construct the synthetic seismogram. Following the tie, picking horizons was based on tracking a reflection through a seismic line and correlating the intersections with the other lines to delineate the lateral extension for the analyzed layer, after interpretation. A Two-Way Time (TWT) maps were generated and used after depth conversion in generating structural maps that show the structural geology of the studied area44.
Petrophysical analysis
In the present studied domain, the petrophysical parameters of the sandstone units of the AEB Formation were estimated through the electrical well logs of four wells. The data utilized in this study includes the gamma-ray (GR), depth-resistivity (RT), density (ρb), neutron (ΦN), and sonic (Δt) logs in a digital format. Various types of well logs data were plotted and analyzed using Interactive Petrophysics (IP) version 2018 software.
Lithology interpretation
Interpreting the lithology of the target formation is generally gathered from core and cutting samples. However, we used the accessible well logging data (GR, ρb, ΦN, and Δt) to interpret the lithology of AEB Fm. After preparing and making Q.C. on the used logging curves, the first step of the petrophysical data analysis was to identify the lithological composition of reservoir units.
Shale volume (Vsh) estimation
High GR values reflect the presence of shale. Therefore, according to the used method by45, estimating the GR-Index, IGR is a mandatory to determine the shale volume (Vsh %) using the following Equ. (1):
where: I GR = Gamma ray index. GR log = GR reading from log. GR max = Maximum reading of GR in shale bed. GR min = Minimum reading of GR in clean interval.
We calculated the Vsh% from the GR method using the following non-linear equation: Vsh = 0.33 (2(2*I GR)-1) used by39,40 for the early consolidated rocks (Equ. 1). In addition to the GR index method, the neutron-density combined logs method was used to assess the composition of shale. In this study, the Vsh was estimated using both methods. To obtain the most precise Vsh estimation, the procedure with the lowest Vsh was used. Along with the neuron and density logs, the estimated Vsh was applied to estimate the total and effective porosities.
Formation water resistivity (Rw)
The resistivity log readings provide a record of the electrical conductivity of sedimentary deposits that contain a significant amount of clay minerals and indicate the presence of brines inside the pore spaces. In addition, porosity studies demonstrate a high level of sensitivity to the volume of fluid present inside geological formations. Consequently, the process of determining the resistivity of formation water (Rw) for the different units of the studied AEB Formation involved the use of resistivity and estimated porosity logs as illustrated by Picket’s plot (Fig. 6). The estimation of fluid saturation plays a crucial role in the assessment of hydrocarbon resources. To determine the formation water resistivity of the reservoirs, water-saturated zones were determined and employed to estimate the resistivity of water at various levels within the four chosen members of the Alam El-Bueib Formation. The AEB-1, AEB-3A, AEB-3C, and AEB-6 exhibit formation-water resistivity values of 0.084, 0.039, 0.086, and 0.049, respectively, as estimated by the Pickett’s plot methodology in the Matruh 1-1 well (Fig. 6). As a result, the fluid saturations were determined by using the estimated porosity, water resistivity, and resistivity logs.
Reservoir modeling
Geoscientists, geophysicists, and engineers can combine quantitatively all field data into updatable reservoir models using reservoir modeling, which is known as the “seismic simulation”. The fundamental purpose of reservoir modeling is to assess the hydrocarbon potential and give decision-makers with the valid data they require. The modeling of reservoirs incorporates geological and petrophysical modeling. Geological modeling covers the modeling of structures and facies, while petrophysical modeling deals with porosity and saturation modeling. The structural modeling depicts the region’s architecture and structural pattern. The facies model illustrates the vertical and horizontal distribution of the various lithology within the analyzed units. The area’s distribution of effective porosity and fluid saturation were shown via petrophysical modeling. In hydrocarbon exploration and production studies, the integration of all sorts of reservoir models is a powerful tool. Three-dimensional static reservoir modeling is also a useful technique for locating reservoir boundaries. Numerous logs from wells that have penetrated the investigated reservoirs were used to construct a facies model, which was followed by the construction of the property model (porosity and saturation) for the Matruh Field reservoirs41,42,43,44,45,46,47.
According to47,48, the process of creating a property model is composed of three consecutive phases: (1) geometric; (2) facies; and (3) petrophysical models. Creating a property model requires using all the available geological information to fill the grid cells of the structure model with petrophysical properties. Consequentially, data analysis and well logs scale-up will help in allocating well log data on the model 3D grid. Each grid cell will hold one value; therefore, averaging and scaling up of well log values were made to distribute the reservoir properties between the wells in the 3D-model.
Structural modeling
The first step in constructing the three-dimensional (3D) geological models is to create a structural model based on seismic data interpretation. Throughout the construction of the structural model, we used the formation tops acquired from the drilled wells in the research region, in conjunction with the depth-structure maps, to oversee and fine-tune the procedure. The basic goal of the 3D structural modeling is to understand the geological structure in three dimensions49,50. The key components required to develop a structural model are interpreting faults and horizons40. This framework of horizons and faults also serves as the geometrical input for building the 3D grid and can define the structural model of the AEB reservoirs. 20-2D seismic lines were used to pick the reservoir horizons, and to construct depth maps for all AEB Formation picked horizons. The AEB Fm was divided into zones from the well logs formation tops that prepared based on the tie with the picked horizons. The thickness of each layer designates the number of cells present in each zone, which are then subdivided into layers of equal thickness. Before moving to the next phase of facies modeling process, much consideration should be taken into layering the zones of interest through upscaling of well logs.
Facies modeling
Facies analysis should be applied to understand the sedimentology of the formation through performing high-resolution stratigraphic correlations51,52,53. Facies modeling techniques in petrel software are separated into stochastic, deterministic, and interactive methods. Stochastic model technique was regularly used when the available data are little. As a first step in proceeding to facies modeling, facies logs must be created, followed by the upscaling of these logs to the geological grid53. Through an equation constructed using Petrel software, the gamma ray logs were used to generate discrete facies logs. As the second stage in the facies modelling process, a scaling up of the created reservoir facies log in the 3D-model was made54.
Petrophysical modeling
The purpose of petrophysical modeling is to incorporate fine-scale reservoir porosity and fluid saturation into a 3D grid model. For petrophysical modeling, scaling-up log-derived petrophysical parameters are used to build models. These models were then distributed in the area specified by the facies distribution. During the process of static reservoir modeling, it was extremely important to distribute these features, whether they are continuous or discrete over the grid by assigning a value to each cell in the grid. Using the geophysical logs that were provided for the given wells in the research area, the effective porosity and oil saturation were estimated, and their values were scaled up and dispersed on the wells. The features that were used in constructing the effective porosity and oil saturation models were guided by the structural and facies models55,56,57,58,59,60.
Results
Source rock evaluation
The 15 samples recovered from the shale intervals of the AEB-6 member in the Matruh 1-1 well were analyzed by Rock–Eval pyrolysis. All 15 samples are mature, where they are located in the oil-window zone (Fig. 7, Table 1). The relatively high production indices (PI: 0.24–0.39) are consistent with the Tmax values and further support the interpreted peak oil-window for the Alam El-Bueib Formation (Fig. 7).
For the Unit-6 of Alam El Bueib Formation samples, S1 values (Fig. 8A) which represents The hydrocarbons that undergo vaporization and expulsion from the sample at low temperatures (~ 300 °C) and are quantified in mg HC/g rock vary between 0.2 and 0.86 mg HC/g rock (average 0.43 mg HC/g rock). The pyrolysis-derived (S2) values vary between 0.43 and 2.74 mg HC/g rock (average 0.95 mg HC/g rock) (Fig. 8B) represents the amount of hydrocarbons generated through thermal cracking of the contained kerogen at temperature (~ 300–550 °C). It indicates the capability of the rock to generate hydrocarbons and represents the remaining generative capacity of the rock, which decreases with increasing maturity level, giving a false estimate of the source potential of the mature samples. Therefore, the source generating potential in a mature rock should be corrected by adding the generated free (S1) to the remaining (S2) to give the original generating capacity59. S3 values are between 1.39 and 2.44 mg CO2/g rock (average 1.94 mg CO2/g rock) (Table. 1). Overall, the shale interval of the AEB-6 member is characterized by low S1 values and low S2 values, which indicate poor oil-generating potential. However, the coaly shale Sample 13 at depth (13,084 ft/3988 m) shows a relatively high S2 value (2.74 mg HC/g rock) and high genetic potential (GP = S1 + S2) value (3.6 mg HC/g rock) (Fig. 8C) due to its higher organic richness21,23. The sum of S1 and S2 that represents the genetic potential (G.P.) of the source rock (Fig. 8C) refers to the maximum quantity of oil and gas that a specific amount of the rock may generate under ideal conditions of burial depth and duration23. While the Production Index (PI), expressed as S1/(S1 + S2) (Fig. 8D), serves as the transformation ratio and provides insight into the degree of thermal maturation as well as the existence of migrating hydrocarbons7, the PI values for Unit-6 of the Alam El Bueib Formation vary between 0.23 and 0.4, with an average of 0.32. Furthermore, the consistency of the Tmax values (Fig. 8E) with depth across the Matruh 1-1 well indicates the occurrence of indigenous oil in the AEB-6 member, as contamination with migrated oil is characterized by suppressed Tmax values and abnormal S1 values, which are not detected here7,61. The hydrocarbon quality index (S2/S3) of AEB-Unit-6 (Fig. 8F) varies between 0.23 and 1.49 mg HC/mg CO2 with an average of 0.49 mg HC/mg CO2.
Rock–Eval pyrolysis data at the Matruh 1-1 well for the Alam El-Buieb unit-6 (AEB-6), the Matruh Oil Field. (A) S1: The generated free hydrocarbons (H.C.), (B) Remaining hydrocarbon potential (S2), (C) Genetic potential (GP: S1 + S2), (D) Production index (IP: S1/S1 + S2), (E) Tmax, (F) Hydrocarbon quality index (S2/S3).
Reservoir petrophysics
The lithology content of AEB reservoirs was determined using log responses and log-derived cross plots. The neutron-density cross plots of the IP software were used to estimate the lithology of these members, as illustrated in Fig. 9. Four out of seven reservoir intervals of the Alam El-Bueib Formation (AEB-1, AEB-3A, AEB-3C, and AEB-6) were selected for evaluation. Because their assessed petrophysical characteristics show interesting results along the four wells in the current study; these intervals are distinguished by shale and sand intervals. The litho-saturation crossplot known in the oil industry as Computational Petrophysical Interpretation (CPI) is widely used as a vital and reliable tool for deciding whether to complete, reject, or set aside some formations for possible future testing.
The litho-saturation crossplots of AEB Fm for the four wells encompassed many parameters such as shale volume (Vsh%), effective porosity (Φeff), net pay, gross thickness, and hydrocarbon saturation. These parameters were computed and visually shown in Figs. 10 and 11. In addition, the computed petrophysical parameters for the wells in the Matruh Field were compiled and shown in Table 2. As we can see in track 3 (Figs. 10 and 11), the litho-sturation panel of the four analyzed wells indicates that there is a continuous net pay flag for the selected four units of the AEB Fm. While the net pay flag in the other members of the Alam El-Bueib Formation, AEB-3E, AEB-4, and AEB-5, is not continuous in all wells. This justifies why we based our whole-work analysis on the selected four units.
Results show the average petrophysical calculations of the selected four AEB units (Table 2). Firstly, the AEB-1 member has an average net pay thickness, which ranges between a lowest value of 13 feet in the Matruh-6 well and a highest value of 112 feet in the Sama-1X well. The average percentage of shale volume (Vsh%) varies between 6% at the Matruh-6 well and 20% at the Matruh-5 well. The effective porosity ranges between 15% at the Sama-1X-well and 27% at the Matruh-5 and Matruh-6 wells. The hydrocarbon saturation ranges between 56% at the Matruh 1-1 well and 73% at the Matruh-5 and Matruh-6 wells. Secondly, the petrophysical evaluation of the AEB-3A member shows an average net pay thickness, which ranges between 18 and 139 feet in the Matruh 1-1 and the Sama-1X wells, respectively. Vsh% ranges between 5 and 17% in the Matruh-5 and Matruh 1-1 wells, respectively.
The effective porosity ranges between 14 and 16% in the Matruh 1-1 and Matruh-6 wells, and the hydrocarbon saturation ranges between 52 and 66% in the Matruh-6 and Sama-1X wells. Thirdly, the average net pay thickness of the AEB-3C Unit is 16–73 feet in the Matruh-6 and Matruh-1 wells, and the average shale volume is 12% in the Matruh-6 and 22% in the Matruh-1 and Matruh-5 wells. In addition, the average effective porosity is 13% in the Sama-1X well and 30% in the Matruh-6 well, and the hydrocarbon saturation is 64% in the Matruh-1-1 well and 85% in the Matruh-6 well. Finally, the AEB-6 member has an average net pay of 20 feet in the Matruh-6 well and 160 feet in the Matruh 1-1 well, a Vsh% range of 5–20% in the Matruh-5 and Sama-1X wells, an average effective porosity range between 14–20% in the Sama-1X and Matruh-5 wells, and a hydrocarbon saturation range of 70–88% in the Sama-1X and Matruh-6 wells, respectively.
Seismic interpretation
Depth conversion is a key technique next to interpretation because seismic data are measured in the time domain, while well data is measured in the depth domain. So, depth conversion was made for all-time structure maps, which were later used in mapping target horizons to define the reservoir volumes of certain hydrocarbon accumulations. In the present study, members of the AEB Fm were tracked in all available seismic sections, and TWT contour maps and structure depth conversion maps were constructed for them (Figs. 12 and 13).
Depth structure contour map on the top of (A): AEB-1 member; (B) AEB-2 member; (C) AEB-3A member; (D) AEB-3C member. (Maps generated in Petrel ™ Schlumberger 2017.3 software, https://www.software.slb.com/products/petrel).
Depth structure contour map on the top of (A) AEB-4 member; (B) AEB-5 member; (C) AEB-6 member. (Maps generated in Petrel ™ Schlumberger 2017.3 software, https://www.software.slb.com/products/petrel).
According to the analysis of the seismic data, the studied region is affected by around of ten normal faults. Certain faults impact every level of the AEB Formation, whereas others do not. A total of ten normal faults (F1 to F10) as seen in the depth structure contour map constructed on the top of the AEB Formation’s members (Figs. 12 and 13). These faults affect both AEB-1 and AEB-2 units (Figs. 12A and B). A total of eight normal faults, labeled F1 to F7 and F9 in Fig. 12C, have an effect on AEB-3A. Seven normal faults (F1 to F5, F7, and F9), as seen in Figs. 12D, E, F, and G, impact AEB-3C, AEB-4, AEB-5, and AEB-6 units, respectively. All observed faults exhibit a NW–SE orientation that aligns with the trend of the Gulf of Suez, with the exception of F7, which follows the NE-SW Aqaba trend. The middle section denotes the most elevated location within the mapped members of the AEB Fm in the region. The constructed depth-structure maps describe fault types that are found on the examined surfaces of the AEB Fm. Many representative faults were interpreted, some of which are shown in Figs. 14 and 15.
Four interpreted seismic sections showing the representative faults affecting the Alam El-Buieb Formation: (A) Index map of the two interpreted Line-4 (E-W) and Line 13 (S–N) seismic sections (B) Seismic line 4 passes through Matruh-5 and Matruh-6 wells. (C) Seismic line 13 passes through Matruh-1-1 and Matruh-5 wells. (D) Index map of the two interpreted Line-3 (E-W) and Line 9 (S–N) seismic sections. (E) Seismic Line-3 in the (W-E) direction is cut by three normal faults. (F) Seismic line 9 in the S–N direction, cut by a group of normal faults, makes a horst and grabens on the top of the Alam El-Buieb formation.
Two interpreted seismic sections showing the representative faults affecting the Alam El-Buieb Formation: (A) Index map of three interpreted seismic sections showing the faults affecting the Alam El-Buieb Formation: (B) Line 4 in the (E-W) direction, passing through Matruh-5 and Matruh-6 wells. (C) Line 14 in the (S–N) direction, passing through Matruh-6 well. (D) Line 18 in the NW–SE direction, passing through Matruh-1-1 well.
The interpreted faults and horizons were also used to make time-structure contour maps for the seven members of the AEB Formation. By connecting the formation tops from well logging data to 2D seismic lines, the main units of the AEB Formation could be identified. We used the available check shot survey to calibrate the sonic log for the studied wells in the current study. Then, acoustic impedance was determined using density and calibrated sonic logs, which were later used to calculate the reflectivity coefficient. Synthetic seismograms were made for the selected horizons. Then, velocity information was used later to create time-depth conversion maps, which were converted to a structure depth map that was used later to construct the 3D-structure model.
Structure model
The main purpose of generating a model containing lithology, petrophysical parameters, and structure is to estimate the geology and evaluate the target formations in the undrilled locations58. Consequently, the provided seismic data helped in defining the structural patterns that affect the AEB Fm in the location of the studied wells. The constructed 3D model of Alam El-Bueib Formation units (Fig. 16) mostly comprises the structural framework of the Matruh Basin.
The boundary of the Matruh Field was delineated by interpreting the fault sticks from the 2D seismic survey to build a fault model in the time domain, which was later converted into the depth domain through the velocity model. The availability of time-depth data helped in the creation of TWT structure maps and structure-depth maps for the Alam El Buieb Formation unites, as shown in Figs. 12 and 13. This represents the converted structure depth contour map from the TWT structure maps of the seven members of the Alam El-Bueib Formation. The developed structure maps for the AEB Formation’s members demonstrate that the structures that affect the area have two main trends: NW–SE and NE-SW. These maps were used to create the structural model in Fig. 16.
The interpreted seismic sections (Figs. 14 and 15), along with the 3D structure-model intersections (Fig. 16), show that the distribution of the faults throughout the region produces both grabens and horsts. Additionally, a cross section passing through the Matruh 1-1 and Matruh-5 wells shows the thickness and the distribution of all picked horizons of the Alam El-Bueib Formation units (Fig. 17). Moreover, a cross section passing through the Matruh1-1, Matruh-5, and Matruh-6 wells shows the thickness distribution of the seven picked horizons of the Alam El-Bueib Formation (Fig. 18).
Facies and property model
An integrated model was constructed in Petrel to combine the four selected AEB sandstone reservoir units, cross-sections from facies, and a property model to predict the extension of hydrocarbon in the reservoir, as illustrated in Figs. 19, 20, 21, 22, 23, 24. This integrated model proves the validity of applying the 3D model in the Matruh Field.
Model validation
The Apidose-1X well was utilized as an uncalibrated well to verify the validity of the facies, porosity, and saturation models that were produced. The facies log was obtained by using the gamma-ray log, while the estimation of effective porosity was conducted by employing neutron and density logs. Additionally, an estimation of fluid saturation was also performed. Figure 25 illustrates the intersection resulting from the convergence of the blind well and the diverse models. The log-derived facies, porosity, and saturation in the validation well exhibit a strong resemblance to those of the developed models as seen in Fig. 25.
Discussion
The seismic interpretation of the Alam El-Bueib Formation (AEB Fm) in the Matruh Field requires identifying all the seismic facies within the formation as well as analyzing the existing structures. The AEB reservoir units in the Matruh Basin are mainly cut by normal faults, as shown in the interpreted seismic sections (Figs. 14 and 15). The provided 2D seismic lines have two principal trends, N-S and E-W. Seven levels of the AEB Fm were identified and picked in both directions. Two-way time structure maps were constructed for the seven levels and then converted to depth structure contour maps (Figs. 12 and 13). Moreover, the constructed structure depth maps for the members of the AEB Fm reveal that in addition to the anticline fold extending in the NE-SW direction that resulted from the Syrian Arch System event, there are a number of normal faults with two predominant NE-SW and NW–SE trends. These normal faults are structural traps, which are essential elements in the petroleum system of the field. Understanding the structures of the area is essential for optimizing the drilling and completion of wells in order to maximize hydrocarbon recovery, as faults within the formation play a major role in regulating hydrocarbon distribution and migration. The converted structure depth maps and the structure-model intersections show that in the current study, both the anticline fold and faults play a crucial role in creating AEB Fm structural traps in the Matruh Basin. An analogous study on the Alamein Field by62 came to the conclusion that structures in the studied area had a significant impact on the development of the reservoir rock’s thickness and trap formation. The structure identification of the Alamein Field shows that the basin inversion associated with the rifting of the Alamein area caused the abrupt increase in thickness of the AEB Fm.
In the current study, the effective porosity and facies models are quite comparable. Consequently, the property model was made to clarify the key aspects that control both models and to explain why each member of AEB Fm was modeled individually. The comprehensive examination of the AEB hydrocarbon reservoir using well logs and seismic data indicates that the neutron-density cross plots show the effect of shale content on point distribution, where the points show clusters of the same shale values. Higher shale content values pull the points down from sandstone towards limestone and dolomite lines, as shown in Fig. 9. In our study, both techniques (Vsh from gamma ray logs and neutron-density logs) were used to estimate the Vsh%. The least Vsh of both techniques was determined to be the most accurate Vsh data. The lithological heterogeneity of the AEB members affected the lateral and vertical distribution of the effective porosity and fluid saturation. Thus, four out of seven AEB Fm members (AEB-1, AEB-3A, AEB-3C, and AEB-6) show good petrophysical properties. The sandstone component of the AEB-6 member is considered to be the most favorable member in this context. However, its shaly facies is deemed to be a poor to fair oil source rock in the Matruh 1-1 well. This observation suggests that the AEB-6 member exhibits both dual source and reservoir properties. This conclusion is supported by work done on the AEB in the Jade Oil Field in the Matruh Basin, where hydrocarbon accumulation was theoretically found in the AEB-6 in the Jade-5 well by 22. It is important to note that the AEB Fm shows regionally heterogeneous variations in its petrophysical characteristics across the Matruh Basin. The litho-saturation panels (Fig. 10) and the 3D facies model (Figs. 19 and 20A) show that it clearly exhibits upward changes from higher shale content at its base (i.e., AEB-6 Unit) to more permeable sandy facies at the top (i.e., AEB-1) in a N-S direction along the Matruh 1-1 and Sama-1 wells. This is expected to confine generated hydrocarbons within the same impermeable shale source rock intervals, which act as unconventional reservoirs, as shown in the oil saturation model of the Matruh 1-1 and Matruh-5 wells (Fig. 24). This type of reservoir is commonly associated with drilling complications and requires special drilling strategies to have successful hydrocarbon production.
On the other hand, the AEB Fm shows an opposite trend in its petrophysical characteristics in an E-W direction. It exhibits clear upward changes from more permeable sandy facies at its base (i.e., AEB-6 Unit) to less permeable shaly facies at its top (i.e., AEB-1) along the Matruh-5 and Matruh-6 wells (Figs. 11 and 20B). Thus, the occurrence of local shale sealing rocks along the E-W direction in addition to the structural traps is expected to confine some hydrocarbon accumulations at shallower depths, as shown in the middle part of the Matruh-5 well (Fig. 24). The hydrocarbon production from this type of reservoir is expected to be easier in comparison to its counterpart along the N-S direction. Overall, the local reservoir heterogeneity shown above necessitates conducting further investigations on the AEB reservoir characteristics in other parts of the Matruh Basin to fully understand its hydrocarbon prospect.
To test the validity of our models in the current study, the Apidos-1X well was used as a blind well in the validation process of the facies, porosity, and saturation models that were derived for the studied levels of the AEB Fm. This played a crucial role because it serves as an important tool in validating the accuracy and reliability of the derived models. The good match between the log-derived data and the built models confirms the accuracy of our constructed models. This enables us to get a deeper understanding of the characteristics of the studied reservoirs and make better decisions for hydrocarbon exploration and production.
The impact of tectonic events on reservoir development and specifically its heterogeneity was also explained by work done by63 on a thick lower Miocene section in the Offshore North Sinai Basin. These authors63 reached the conclusion that the tectonic effect plays a main role in reservoir distribution, thickness, and heterogeneity. Additionally, comparable work was done by author64 on the Middle Jurassic and Cretaceous rocks in Tut Oilfield, Shushan Basin, through studying the composite logs for five wells. This work64 considered the units AEB-1, AEB-3A, 3D, and 3E of the AEB Fm as important reservoir rocks. The basin model constructed by64 for the organic-rich Jurassic-Cretaceous rocks indicated that AEB Fm contains some source rock intervals, which are mature and are still within the early stage of hydrocarbon generation. While reservoir evaluation of the four AEB units indicates that they are hydrocarbon-bearing and have an effective porosity mean value of 15.3% in AEB-1, 13.8% in AEB-3A, 10.7% in AEB-3D, and 14.3% in AEB-3E. These results are somehow close to the findings of our current research on the AEB Fm, particularly for the AEB-3A Unit. This indicates that AEB Fm has similar regional petrophysical characteristics across the adjacent Matruh and Shushan basins, but with local dissimilarity in other parts of the two basins is due to their relatively different tectonostratigraphic evolutions.
Regionally, to follow the effect of shale volume (Vsh) on reservoir potential, Authors65 studied the Lower Cretaceous of Qishn clastics reservoirs in the Sharyoof oilfield in Yemen, which revealed high hydrocarbon saturation in the S1A reservoir but almost nonexistent in the S1B reservoir due to higher shale content, 90% water saturation, and lower effective porosity. The Upper Qishn clastics subunits S1A and S1C performed best, similar to the Alam El-Bueib Formation units AEB-3A and AEB-6 in Egypt, because they have the lowest shale content.
On the other hand, authors66 studied the Khatatba Formation in the Matruh-Shushan Basin by interpreting thirteen 2D seismic lines and five wells. They used a 3D structure model to trace out the main structure through faults that crossed the area. They also analyzed the petrophysical properties of the Upper and Lower Safa members to see how the interpreted faults affected the main reservoirs. They used the same materials and tools as what we have used in our current research and reached the conclusion that it is imperative to construct a 3D structure model to trace out and understand the effect of faults on the studied reservoirs. However, in our current research, we additionally used the distribution of the interpreted reservoir main facies, calculated petrophysical parameters, and saturation in the 3D geologic model. We also tested the validity of our constructed model through a blind test. Authors67 also used the same tools and materials (i.e., composite logs and 2D seismic lines) to make reservoir characterizations for the Bahariya Formation in the Shorouk Field in the Shushan Basin. They made a correlation between the reservoir units in the 5 wells studied and interpreted 2D seismic lines by constructing 2D structure depth maps. They reached an important conclusion, which highlights the impact of the active Late Cretaceous tectonics on the development of the Bahariya Formation reservoir. Authors68 studied the Khataba Formation in the Apidose-1X well, which was used as a validation well in the current study in the same field, the Matruh field. They constructed a basin model, and their results reached the conclusion that the end of the Cretaceous to Early Tertiary to Late Paleocene (60–58 Ma ago) was characterized by a major uplifting phase due to tectonic inversion. Author69 investigated the depositional environment and paleoclimate conditions of the Middle Jurassic Khatatba Formation in Matruh-5 and Matruh-6 wells at the Matruh field in Matruh Basin. She reached the conclusion that the Tethyan rifting that occurred during the Late Jurassic and Early Cretaceous caused subsidence events in Matruh basin, which were accordingly associated with source rock maturation. By comparing our work to the work done by authors63,64,65,66,67,68,69, we can draw the conclusion that it is of prime importance to monitor the tectonics of the basin and interpret the main faults to understand their effect on reservoir thickness, distribution, and heterogeneity.
Conclusions
Several publications investigated the hydrocarbon potential of the Early Cretaceous Alam El-Bueib (AEB) Formation in the North Western Desert of Egypt. However, few studies focused on the Matruh Basin. Thus, the current work investigated the petrophysical properties of the Alam El-Bueib Formation to assess its reservoir potential. The main concluding remarks of the current work are as follows:
-
The Alam El-Bueib Formation is composed mainly of sandstone with several shale intercalations showing variable thicknesses and/or volumes in the studied wells.
-
Four out of seven AEB members (AEB-1, AEB-3A, AEB-3C, and AEB-6) demonstrated good petrophysical properties.
-
The most promising member is AEB-6, but the shaly facies part shows poor to fair source rock potential in contrast to its well-known pure reservoir character depicted from other oil fields in the Matruh Basin, which are hydrocarbon productive.
-
Analysis of 2D seismic data resulted in generating depth structure maps for AEB Fm’s members, which show that the Matruh Oil Field is cut by several normal faults with NW–SE and NE-SW directions.
-
Analysis of well logs and seismic data was conducted in order to develop the 3D geological and petrophysical models. The presented models illustrate the lateral and vertical distributions of the significant characteristics that determined the hydrocarbon potential of the Matruh Oil Field.
-
The effective porosity and saturation models for the study area can be utilized to suggest new prospects in order to develop the Matruh Oil Field.
-
3D petrophysical modeling of AEB Fm shows the distribution of conventional reservoirs along an E-W trend and unconventional reservoirs along a N-S trend, which exemplifies its regional reservoir heterogeneity across the Matruh Basin.
-
More investigations are needed to understand the regional reservoir characteristics of the AEB Fm in different parts of the Matruh Basin.
Data availability
The data that support the findings of this study are available from [the Egyptian General Petroleum Corporation] but restrictions apply to the availability of these data, which were used under license for the current study, and so are not publicly available. Data are however available from the corresponding author upon reasonable request and with permission of [the Egyptian General Petroleum Corporation].
References
International Energy Agency. Oil Market Report (IEA, 2022).
Shahin, A. N. Undiscovered petroleum reserves in North Western Desert, Egypt. In 1st International Conference of the Geology of the Arab World, Cairo University (1992).
Egyptian General Petroleum Corporation. Western Desert: Oil and gas fields, a comprehensive overview. In EGPC, 11th Petroleum Exploration and Production Conference 431 (1992).
Schlumberger. Geology of Egypt. Paper presented at the Well Evaluation Conference, Schlumberger, Cairo 58–66 (1995).
Metwalli, F. I., Pigott, J. D., Ramadan, F. S., El-Khadragy, A. A. & Afify, W. A. Alam El Bueib reservoir characterization, Tut Oil Field, North Western. Environ. Earth Sci. 77(4), 1–21. https://doi.org/10.1007/s12665-018-7290-0 (2018).
Metwalli, F. I. & Pigott, J. D. Analysis of petroleum system criticals of the Matruh-Shushan Basin, Western Desert Egypt. Pet. Geosci. 11(2), 157–178. https://doi.org/10.1144/1354-079303-593 (2005).
Shalaby, M. R., Hakimi, M. H. & Abdullah, W. H. Diagenesis in the middle Jurassic Khatatba formation sandstones in the Shoushan Basin, northern Western Desert Egypt. Geol. J. 49(3), 239–255. https://doi.org/10.1002/gj.2512 (2014).
Ramadan, F. S., El Nady, M. M., Eysa, E. A. & Mahdy, S. A. Isopach, lithofacies changes, and source rocks characteristics of Khatatba and Alam El Bueib formations of some wells in North East Western Desert Egypt. Petrol. Sci. Tech. 34(23), 1920–1928 (2016).
Nabih, M. Reliability of velocity-deviation logs for shale content evaluation in clastic reservoirs: A case study Egypt. Arab. J. Geosci. 14(6), 507 (2021).
Meshref, W. M. Regional Structural Setting of Northern Egypt. In EGPC 6th Exploration Seminar. Cairo 11 (1982).
Parker, J. R. Hydrocarbon habitat of the Western Desert, Egypt. In Proc of the EGPC 6th. Exploration and Production Conference, Cairo. EGPC, 1 (1982).
Said, R. The Geology of Egypt 734 (Brookfield, 1990).
El-Khadragy, A. A., Saad, M. H. & Azab, A. Crustal modeling of south Sitra area, north Western Desert, Egypt using Bouguer gravity data. J. Appl. Sci. Res. 6(1), 22–37 (2010).
Metwalli, F. I., Shendi, E. A. H. & Fagelnour, M. S. Seismic facies analysis of thin sandstone reservoirs, North Western Desert Egypt. J. Petrol. Expl. Prod. Tech. 9, 793–808. https://doi.org/10.1007/s13202-018-0541-5 (2019).
El Bastawesy, M., Afify, W., Barakat, M., & EL Gendy, N. Petroleum System analyses of middle jurassic and early cretaceous rocks, Matruh Basin, North Western Desert, Egypt. In European Association of Geoscientists and Engineers, Conference. Proc., 82nd EAGE Annual Conference & Exhibition 1–5 https://doi.org/10.3997/2214-4609.202010690 (2020).
Elhossainy, M. M., Basal, A. K., ElBadrawy, H. T., Salam, S. A. & Sarhan, M. A. Well logging data interpretation for appraising the performance of Alam El-Bueib reservoir in Safir Oil Field, Shushan Basin Egypt. J. Petrol. Expl. Prod. Tech. 11(5), 2075–2089. https://doi.org/10.1007/s13202-021-01165-7 (2021).
Abu El Naga, M. Paleozoic and Mesozoic depocenters and hydrocarbon generating areas, northern Western Desert. In 7th Petroleum and Exploration Seminar, EGPC, Cairo 8 (1984).
Meshref, W. M. Cretaceous tectonics and its impact on oil exploration in northern Egypt. Geol. Soci. Egypt Spec. Publ. 2, 199–244 (1999).
Guiraud, R. & Bosworth, W. Phanerozoic geodynamic evolution of northeastern Africa and the northwestern Arabian platform. Tectonophysics 315(1–4), 73–104 (1999).
Shalaby, M. R., Hakimi, M. H. & Abdullah, W. H. Organic geochemical characteristics and interpreted depositional environment of the Khatatba Formation, northern Western Desert Egypt. AAPG Bull. 96(11), 2019–2036. https://doi.org/10.1306/04181211178 (2012).
Deaf, A. S., Omran, A. A., El-Arab, E. S. Z. & Maky, A. B. F. Integrated organic geochemical/petrographic and well logging analyses to evaluate the hydrocarbon source rock potential of the Middle Jurassic upper Khatatba Formation in Matruh Basin, northwestern Egypt. Mar. Pet. Geol. 140, 105622 (2022).
Selim, E. S. I., Omran, M. A. & El-Twargy, E. Evaluation of hydrocarbon prospects by the use of 3D seismic data at the Cretaceous formations in Jade field, Matruh Basin, North Western Desert Egypt. Arab. J. Geosci. 14, 1–17. https://doi.org/10.1007/s12517-021-08335-1 (2021).
Deaf, A. S. et al. Organic geochemical, palynofacies, and petrographic analyses examining the hydrocarbon potential of the Kharita Formation (Albian) in the Matruh Basin, northwestern Egypt. Mar. Pet. Geol. 112, 104087 (2020).
Moustafa, A. R. et al. Matruh basin: Hydrocarbon plays in an inverted Jurassic-Cretaceous rift basin in the northern Western Desert of Egypt. In AAPG Internation Meeting Cairo (2002).
Barakat, M. K., El-Gendy, N. H. & El-Bastawesy, M. A. Structural modeling of the Alam EL-Bueib formation in the Jade Oil Field, Western Desert Egypt. J. Afr. Earth Sci. 156, 168–177. https://doi.org/10.1016/j.jafrearsci.2019.05.003 (2019).
Makled, W. A., Mostafa, T. F., El Sawy, M. Z., Mousa, D. A. & Ragab, M. O. Petroleum play of the lower cretaceous Alam El Bueib formation in the El Noor-1X well in the north Western Desert (Egypt): A sequence stratigraphic framework. Mar. Pet. Geol. 116, 104287. https://doi.org/10.1016/j.marpetgeo.2020.104287 (2020).
Mostafa, T. F., Deaf, A. S., El Soughier, M. I. & Makled, W. A. Palynostratigraphy and paleoecology of a lower cretaceous (upper Barremian–lower Aptian) succession in the Shushan Basin, northwestern Egypt: Inferences on intra-and inter-basinal correlations. Neus. Jahr. Geol. Paläontol. Abh. 27, 177–195 (2019).
Bosworth, W., Abrams, M., Drummond, M. & Thompson, M. Jurassic rift initiation source rock in the Western Desert, Egypt—relevance to exploration in other continental rift systems. In Petroleum Systems in “Rift” Basins (eds Post, P. J. et al.) (Gulf Coast Section SEPM, 2015). https://doi.org/10.5724/gcs.15.34.0615.
Meshref, W. M. & Hammouda, H. Basement tectonic map of Northern Egypt. In Proc. EGPC 9th Exploration and Production Conference, Cairo. EGPC Bulletin 1 (1990).
Dolson, J. C., Shann, M. V., Matbouly, S., Harwood, C., Rashed, R. & Hammouda, H. The petroleum potential of Egypt. In Petroleum Provinces of the 21st Century, Memoir 74. AAPG Bulletin (ed. Morgan, W. A.) 453–482 https://doi.org/10.21608/jpme.2022.125833.1117(2001).
Moustafa, A. R. Mesozoic-Cenozoic basin evolution in the northern Western Desert of Egypt. In 3rd symposium on the sedimentary Basins of Libya. Geology of East Libya 3 (2008).
Abuzaied, M., Metwally, A., Mabrouk, W., Khalil, M. & Bakr, A. Seismic interpretation for the Jurassic/Paleozoic reservoirs of QASR gas field, Shushan-Matrouh Basin north Western Desert Egypt. Egypt. J. Pet. 28(1), 103–110. https://doi.org/10.1016/j.ejpe.2018.12.008 (2019).
Sultan, N., Halim, M. A. Tectonic framework of northern Western Desert, Egypt and its effect on hydrocarbon accumulations.In Proceed. EGPC 9th Expl. & Prod. Conf., Cairo. EGPC Bulletin.Vol. 2 , 1–19 (1988).
Guiraud, R. et al. Phanerozoic history of Egypt and surrounding areas. Peri-Tethys Memoir 6, 469–509 (2001).
Fawzy, A.,& Dahi, M. Regional geological evaluation of the Western Desert, Egypt. In Geol. Arab. W. Conf., Cairo University, 111–149 (1992).
Badley, M. E. Practical Seismic Interpretation (IHRDC Press, 1987).
Fagelnour, M. S., Metwalli, F. I. & Shendi, E. A. H. Structural and facies modeling of the lower cretaceous Alam El Bueib reservoirs in the Shushan Basin, Western Desert Egypt. Arab. J. Geosci. 11, 1–24. https://doi.org/10.1007/s12517-018-3909-4 (2018).
Liu, L. & Lee, Y. J. Geochemistry of source rocks in the lower tertiary nadu formation, eastern depression of the baise basin, Guangxi Province China. J. Pet. Sci. Eng. 41(1–3), 135–157. https://doi.org/10.1016/S0920-4105(03)00149-9 (2004).
Farag, M. I. A. I. Geophysical Reservoir Evaluation of Obaiyed Field, Western Desert, Egypt. https://doi.org/10.14279/depositonce-2626(2010)
Avseth, P. & Bachrac, R. Seismic properties of unconsolidated sands: Tangential stiffness, Vp/Vs ratios and diagenesis. In SEG International Exposition and Annual Meeting (SEG-2005). https://doi.org/10.1190/1.2147968(2005).
Barakat, M. K., Azab, A. & Michael, N. Reservoir characterization using the seismic reflection data: Bahariya formation as a case study Shushan Basin, North Western Desert Egypt. J. Petr. Min. Eng. 24(1), 5–15. https://doi.org/10.21608/jpme.2022.110315.1107 (2022).
Brown, A. R. Interpretation OF Three-Dimensional Seismic Data, 6th edn. 534 (AAPG & Soci. Expl. Geoph, 2004).
Henry, S. G. Understanding the seismic wavelet. Articles from Geophysical Corner (GC). In AAPG. Explorer, 40028. https://doi.org/10.1029/97RG00427 (2001).
Schlumberger.,. Log Interpretation Manual: Vol.II (Application) (Schlumberger Limited, 1974).
Abdelwahhab, M. A., Ali, E. H. & Abdelhafez, N. A. Petroleum system analysis-conjoined 3D-static reservoir modeling in a 3-way and 4-way dip closure setting: Insights into petroleum geology of fluvio-marine deposits at BED-2 Field (Western Desert, Egypt). Petroleum 9(1), 8–32. https://doi.org/10.1016/j.petlm.2021.06.001 (2023).
Schlumberger, S. Petrel Introduction Course 13–493 (Schlumberger Ltd Huston, 2010).
Abu-Hashish, M. F. & Said, A. Volumetric assessment through 3D geostatic model for Abu Roash “G” reservoir in Amana Field-East Abu Gharadig Basin-Western Desert-Egypt. J. Geol. Geophys. 5(2), 12. https://doi.org/10.4172/2381-8719.1000242 (2016).
Abdel-Fattah, M. I., Metwalli, F. I. & El Sayed, I. M. Static reservoir modeling of the Bahariya reservoirs for the oilfields development in South Umbarka area, Western Desert Egypt. J. Afr. Earth Sci. 138, 1–13. https://doi.org/10.1016/j.jafrearsci.2017.11.002 (2018).
Abdelmaksoud, A., Ewida, H. F., El-Habaak, G. H. & Amin, A. T. 3D structural modeling of the Upper Bahariya Member in Abu Gharadig oil and gas field, North Western Desert Egypt. J. Afr. Earth Sci. 150, 685–700. https://doi.org/10.1016/j.jafrearsci.2018.09.022 (2019).
Henriquez, A., Tyler, K. J. & Hurst, A. Characterization of fluvial sedimentology for reservoir simulation modeling. SPE. F. Eval. 5(03), 211–216 (1990).
Hirst, J. P., Blackstock, C. R. & Tyson, S. Stochastic modelling of fluvial sandstone bodies. Geol. Modell. Hydrocarb. Reserv. Outcrop Analog. 15, 237–252 (1993).
Wescott, W. A. Geomorphic thresholds and complex response of fluvial systems—Some implications for sequence stratigraphy. AAPG Bull. 77(7), 1208–1218 (1993).
Deutsch, C. V. & Journel, A. G. Geostatistical software library and user’s guide. New York 119(147), 578 (1992).
Eysa, E. A., Ramadan, F. S., El Nady, M. M. & Said, N. M. Reservoir characterization using porosity–permeability relations and statistical analysis: A case study from North Western Desert Egypt. Arab. J. Geosci. 9, 1–9. https://doi.org/10.1007/s12517-016-2430-x (2016).
Taha, M. A., Abdelhafeez, T. H., El-Hady, S. M., Nooh, A. Z. & Mohamed, W. H. Improving hydrocarbon prospect evaluation at Badr El Din-3 and Badr El Din-15 Oil Fields by Integrating 3D structural modeling and petrophysical analysis for Abu-Gharadig Basin, North of Western Desert Egyp. Arab. J. Sci. Eng. 48(1), 625–643. https://doi.org/10.1007/s13369-022-07038-3 (2023).
Shalaby, M. R. Petrophysical characteristics and hydraulic flow units of reservoir rocks: Case study from the Khatatba formation, Qasr field, North Western Desert Egypt. J. Petrol. Sci. Eng. 198, 108143. https://doi.org/10.1016/j.petrol.2020.108143 (2021).
Afify, W., Barakat, M. K., Elgindy, N. H. & Elbastawesy, M. A. Petrophysical evaluation and pressure analysis of the cretaceous Alam EL-Bueib sand reservoirs, Jade Field, North Western Desert Egypt. Delta J. Sci. 38(2), 248–260. https://doi.org/10.9790/0990-0501024062 (2017).
Abu-Hashish, M. F., Wanas, H. A. & Madian, E. 3D geological modeling of the upper cretaceous reservoirs in GPT oil field, Abu Sennan area, Western Desert Egypt. J. Pet. Expl. Prod. Tech. 10, 371–393. https://doi.org/10.1007/s13202-019-00780-9 (2020).
Waples, D. W. Geochemistry in Petroleum Exploration 232 (International human resources and development corporation, 1985).
Gentzis, T., Carvajal-Ortiz, H., Deaf, A. & Tahoun, S. S. Multi-proxy approach to screen the hydrocarbon potential of the Jurassic succession in the Matruh Basin, North Western Desert Egypt. Int. J. Coal. Geol. 190, 29–41 (2018).
Abdelwahhab, M. A. & Raef, A. Integrated reservoir and basin modeling in understanding the petroleum system and evaluating prospects: The Cenomanian reservoir, Bahariya Formation, at Falak Field, Shushan Basin, Western Desert Egypt. J. Pet. Sci. Eng. 189, 107023. https://doi.org/10.1016/j.petrol.2020.107023 (2020).
El-Nikhely, A. et al. Decoding of seismic data for complex stratigraphic traps revealing by seismic attributes analogy in Yidma/Alamein concession area Western Desert Egypt. J. Pet. Expl. Prod. Tech. 12(12), 3325–3338 (2022).
El-Ata, A. S. A. et al. Seismic characteristics and AVO response for non-uniform Miocene reservoirs in offshore eastern Mediterranean region Egypt. Sci. Rep. 13, 8897. https://doi.org/10.1038/s41598-023-35718-z (2023).
Barakat, M. K. Petrophysical evaluation and potential capability of hydrocarbon generation of Jurassic and Cretaceous source rocks in Shoushan Basin, North Western Desert Egypt. IOSR J. App. Geol. Geophys. 5, 23–45 (2017).
Abdullah, E. A., Al-Areeq, N. M., Al-Masgari, A. A. S. A. & Barakat, M. K. Petrophysical evaluation of the upper Qishn clastic reservoir in Sharyoof oil Field, Sayun-Masilah Basin Yemen. ARPN. J. Eng. App. Sci. 16(22), 2375–2394 (2021).
Eid, A. M., Mabrouk, W. M., Amer, M. & Metwally, A. 3D structural modeling using seismic data and well logs for Khatatba reservoir in Matruh-Shushan Basin, North Western Desert Egypt. Sci. Rep. 13(1), 20158 (2023).
Barakat, M. K., Azab, A. & Michael, N. Reservoir characterization using the seismic reflection data: Bahariya formation as a case study Shushan Basin, North Western Desert Egypt. J. Petrol. Min. Eng. 24(1), 5–15 (2022).
Ali, W. A. & Fagelnour, M. Burial and thermal history simulation of the Middle Jurassic source rocks in Matruh basin, north Western Desert, Egypt. Delta J. Sci. 47(1), 171–191. https://doi.org/10.21608/DJS.2024.256058.1142 (2023).
Ali, W. A. Depositional environment and paleoclimate of the middle Jurassic sedimentary rocks in Matruh Basin, Northwestern Desert Egypt. Egypt. J. of Geol. 67(1), 299–319. https://doi.org/10.21608/EGJG.2024.256634.1066 (2023).
Acknowledgements
The authors are grateful to the Egyptian General Petroleum Corporation (EGPC) and Khalda Petroleum Company (KPC) for supplying the raw material, required reports from their archives, the digital logs, seismic data to be utilized in this research, and permission for publication. The authors also appreciate the support from geophysicist Ahmed Said (KPC) for making Q.C. on the seismic work done in this project.
Funding
Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB).
Author information
Authors and Affiliations
Contributions
The 1st author [Walaa A. Ali] and 3rd author [Taher Mostafa] contributed to the study’s conception and design, while the 2nd author [Amr S. Deaf] revised the third version of the manuscript, restructured, rewrote, and provided additional interpretations to a section of the paper. Material preparation, data collection, proposal writing, and the approval process to use the data used in this research from the Egyptian General Petroleum Corporation (EGPC) were performed by the first author. The first draft of the manuscript was written by the 3rd author, edited by the 1st author, and reedited by the 1st and 2nd authors until the submission by the 1st author. All authors read and approved the final manuscript for submission. The authors are grateful to the Egyptian General Petroleum Corporation (EGPC) for their permission for publication, and they read and approved the final manuscript. The results, data, and figures in this manuscript have not been published elsewhere, nor are they under consideration from another publisher.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Ali, W.A., Deaf, A.S. & Mostafa, T. 3D geological and petrophysical modeling of Alam El-Bueib Formation using well logs and seismic data in Matruh Field, northwestern Egypt. Sci Rep 14, 6849 (2024). https://doi.org/10.1038/s41598-024-56825-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-024-56825-5
- Springer Nature Limited