Abstract
CO2 enrichment is an essential environmental control technology due to its significantly enhancing effect on crop production capacity. Despite being a key energy consumer in protected agriculture (i.e. greenhouse systems), CO2 enrichment remains at a low energy use efficiency level, highlighting the need for developing more energy-efficiency strategies for CO2 enrichment. Therefore, this study employed the computational fluid dynamics (CFD) simulation method to replicate the CO2 diffusion process resulting from CO2 enrichment in three commercial strawberry greenhouses with varying geometric characteristics. Based on the CFD-simulated CO2 concentration distributions, the leaf photosynthetic rate was calculated using a mathematical model group. The CO2 enrichment efficiency was then analysed by calculating the ratio of increased photosynthesis across the cultivation area to the amount of energy (in CO2 equivalent) used. The efficiency peaked when the average CO2 concentration was approximately 500 μmol mol−1, thereby providing guidance for determining the target concentration of CO2 enrichment in production. Although this study is limited as the CFD simulation only considered a typical short-period CO2 enrichment event, future research will provide a broader analysis by considering changes throughout the day.
Similar content being viewed by others
Introduction
Energy utilisation and CO2 emissions are strongly interconnected with climate change and global warming, which pose significant threats to ecosystems. Agricultural activities account for ~ 30% of total global energy consumption1 and contribute to ~ 20% of total anthropogenic CO2 emissions2. Protected horticulture, i.e., crop production in greenhouses, is considered an intensive farming system in terms of production, topping the energy consumers in the agricultural sector3. Unlike open field production, greenhouse production could control environmental parameters, such as temperature, humidity, CO2 concentration, wind speed and solar radiation4, and this would significantly contribute to crop productivity5. However, controlling environmental parameters can incur enormous energy consumption and markedly increase production costs6. Therefore, conducting accurate analyses of the performance of different existing environmental control methods is crucial. Such analyses can provide valuable guidance for optimising environmental control strategies, resulting in improved efficiency and maximised production capacity in greenhouses. Ultimately, this optimisation can lead to the best possible economic and environmental benefits.
CO2 enrichment has been widely used in modern greenhouses as an effective method of increasing crop yield7,8. Numerous studies conducted thus far have demonstrated its effectiveness in promoting crop photosynthesis, growth, yield and quality1,9,10. Owing to its readily available raw materials, moderate cost and easy control, kerosene-generated CO2 has become the predominant source for CO2 enrichment in Japanese greenhouses.
Using exhaust gas as a CO2 source could directly relate to fossil fuel consumption, so the efficiency of CO2 enrichment serves as a key parameter when considering economic and eco-friendly production practices. Researchers have proposed various evaluation criteria for assessing CO2 enrichment efficiency. Sánchez-Guerrero et al.11 reported an 8% average efficiency by employing the content of C-assimilates in the shoot part produced through CO2 enrichment and comparing it to the amount of CO2 used. Kuroyanagi et al.12 reported a 45.5% average efficiency by calculating the proportion of crop-absorbed CO2 in a closed greenhouse to the total CO2 used. These findings indicate significant room for improving efficiency in order to realise decreased costs and CO2 emissions.
In order to uncover more efficient and eco-friendly CO2 enrichment strategies, the CO2 enrichment performance in commercial production requires clarification. Many factors are closely related to this performance, including spatial distribution of CO2 in different greenhouses, its impact on photosynthesis and CO2 utilisation efficiency. While environmental controls can optimise the microclimates within greenhouses, they often introduce spatiotemporal heterogeneity in environmental parameters13. For example, Zhang et al.14 analysed the CO2 concentration distribution inside a greenhouse using different enrichment strategies, revealing its inherent dependence on enrichment methods. The study concluded that coordinating such heterogeneity with the distribution of crops inside greenhouse spaces is an important factor for effective production. With this consideration, clarifying the CO2 spatial distribution is essential for accurately assessing CO2 enrichment performance. However, given the huge size of commercial greenhouses, obtaining an accurate measurement of CO2 distribution through actual means remains challenging. Computational fluid dynamics (CFD) could overcome the identified problems, as it provides an effective method for elucidating the distribution of microclimate parameters within greenhouses15. CFD has been extensively applied and validated in studies to predict the distribution of environmental parameters, including temperature16,17, humidity18,19 and wind speed20. The application of CFD technology in stimulating CO2 distribution within greenhouses has been reported. Roy et al.21 and Boulard et al.22 analysed CO2 distribution simulations in greenhouses under CO2 enrichment.
The primary objective of implementing CO2 enrichment is to enhance crop photosynthesis, thereby increasing greenhouse productivity on a larger scale23. This process is highly intricate, as it involves altering CO2 concentrations to influence crop photosynthesis through various physiological and biochemical reactions. Therefore, evaluations based only on environmental parameters are incomprehensive and fail to incorporate the ultimate target, photosynthesis. Photosynthesis-based evaluations of CO2 enrichment require a clearer understanding of the overall distributions of photosynthesis. Zhang et al.24 visualised leaf photosynthetic rate distribution inside a greenhouse by applying a combined plant–environment-coupled mathematical model group. In that research, environmental parameters inside the greenhouse were simulated using a CFD model, as it provides a convenient method for estimating photosynthesis distribution in large-scale cultivation facilities. Based on the data on photosynthetic capacity change, precise CO2 utilisation efficiency could be obtained by quantitatively analysing the relationship between the photosynthetic capacity change of the greenhouse and the amount of CO2 used.
Furthermore, the geometric features of a greenhouse (e.g. aspect ratio) could greatly influence microclimates inside greenhouses and energy consumption25. In commercial production, greenhouses often vary in aspect ratios and scales based on the available land owned by the cultivator. This variation introduces complex effects on environmental control. Therefore, examining the application of CO2 enrichment in different commercial greenhouses can provide a more objective and comprehensive evaluation, offering valuable insights for commercial production with greater guiding significance. While recent studies have explored new crop-localised enrichment methods24,26,27, burning fossil fuels and directly releasing the resulting CO2 into greenhouse air remains the most widely utilised method for CO2 enrichment. This is primarily due to the easy accessibility of raw materials, moderate cost and simplicity of control associated with this approach28. Therefore, performing an analysis of CO2 enrichment performance in actual commercial greenhouses with different geometric features under the direct release of fossil fuel-generated CO2 gas is crucial.
In this study, experiments were conducted in three commercial strawberry greenhouses with typical length and width, which are representative geometric features of commercial greenhouses in Japan, each greenhouse being equipped with a CO2 generator that produced CO2 gas by burning fuel (kerosene). The objectives of this study were to comprehensively analyse CO2 enrichment performance in commercial production and to propose suitable improvement measures. These aims were achieved following these steps: (1) developing unsteady 3D CFD models to simulate the CO2 diffusion process after enrichment in three different commercial greenhouses, (2) combining CFD with a photosynthetic model to simulate the leaf photosynthetic rate distribution on a greenhouse scale, and (3) evaluating the CO2 enrichment efficiency in the different greenhouses by considering their construction characteristics and discussing the appropriate enrichment strategies. Notably, the main novelty of the study is its visualisation of the distributions of CO2 and photosynthesis within greenhouses during CO2 enrichment and the establishment of their relationship with greenhouse geometric features.
Material and methods
Experimental greenhouses with CO2 enrichment
To evaluate CO2 enrichment performance under commercial conditions, three different greenhouses located in Aso City, Kumamoto Prefecture, Japan (32° 57′ 31 N, 131° 03′ 20.9′′ E) were selected according to their sizes and shapes (Fig. 1): Small Greenhouse (length, 40 m; width, 6 m; height, 3.2 m), Long Greenhouse (length, 84 m; width, 6 m; height, 2.9 m) and Long + Wide Greenhouse (length, 72 m; width, 14 m; height, 3.6 m). Table 1 contains the specific geometric information for the three greenhouses. During the experiment, all greenhouses were managed under conditions of normal commercial production27 and equipped with a CO2 generator (ZO451, FULTA ELECTRIC MACHINERY CO., LTD., Japan), which generated CO2 gas by burning kerosene and released it directly into the space inside. In order to accurately control the CO2 enrichment process, a CO2 concentration monitoring device was employed in the experimental greenhouses. CO2 sensors were arranged near the strawberry at the greenhouse centre to monitor the CO2 concentration inside the greenhouse. In this way, the CO2 concentration changes could be observed in real-time while controlling it manually or automatically by the on–off action of the CO2 generator. In commercial production, the target of CO2 concentration was 1000 μmol mol−1, and the enrichment automatically stopped when the CO2 concentration reached the target value. According to the farmer’s experience and our in-site observation of the CO2 concentration, ~ 10 min was needed for the concentration to reach the target value, so 10 min was chosen as the enrichment duration. During CO2 enrichment, greenhouses were kept closed, and no other environmental control measures were applied. Strawberry plants (Fragaria × ananassa Duch.) were planted in plastic cultivation beds at a height of ~ 1.1 m. The plants were grown in a substrate with an approximate volume of 2 L per plant and irrigated using a nutrient solution.
Measurement and data collection
During the experiment, various environmental parameters (temperature, humidity, solar radiation, CO2 concentration, wind speed) within the greenhouses were measured to provide the data required for setting up the simulation environment and verifying model accuracy. These measurements were made in December 2019 and December 2020. Upon multiple repetitions, four replicates were made for the Small and Long Greenhouses and two replicates were made for the Long + Wide greenhouse, enabling model validation (for air temperature, air relative humidity and CO2 concentration, see Section "CFD simulation accuracy validation"). The experimental greenhouse was kept unventilated during the measurements. CO2 concentrations were measured using CO2 sensors (GMP 252, Vaisala, Finland; an accuracy of ± 40 μmol mol−1 and a measurement range of 0–2000 μmol mol−1) at six points inside each greenhouse. The location and number of sensors were determined by referring to previous studies on CFD analysis21,22,29. The air temperature was measured at the same position for CO2 measurement using T-type thermocouples. The thermocouples were covered with aluminium shield which enables sun protection and natural ventilation. Figures 2 and 3 show the locations of each CO2 and air temperature measurement point, respectively. The height of measurement points (1, 3, 4, 5 and 6) was 1.5 m, and Point 2 was 2.5 m. This arrangement enabled a more comprehensive grasp of the CO2 and air temperature distribution at various locations inside the greenhouses. Solar radiation was measured using three pyranometers (PCM01-SD, PREDE, Japan), where two were located at the greenhouse centre and one was located near the greenhouse roof. The relative humidity of greenhouse air was measured using two humidity sensors (HMP60, Vaisala, Finland; an accuracy of ± 3% and a measurement range of 0%–100%), and these sensors were located around the greenhouse centre, where one was at a canopy height and the other at a 1.5 m height. The generator outlet wind speed was measured using a thermal anemometer (VA21, IET, Japan; an accuracy of ± 3% and a measurement range of 0–40 m s−1). The above data were recorded using a data logger (MIJ-01, Environmental Measurement Japan) at a 10-s interval. Temperatures at various locations (soil, PO plastic film and cultivation bed) in the greenhouse were measured using a mobile type of temperature sensor (Tr-52i, T&D, Japan; an accuracy of ± 0.3 °C and a measurement range of − 60–155 °C). Before starting the experiment, all sensors were placed under the same standard environmental conditions and corrected for differences in each instrument.
Dimensions of three greenhouses: Small Greenhouse (a), Long Greenhouse (b) and Long + Wide Greenhouse (c). The height for CO2 and air temperature measurement points 1, 3, 4, 5 and 6 was 1.5 m and Point 2 was 2.5 m. The height of the air relative humidity measurement Point 1 was around the canopy, and Point 2 was 1.5 m.
CFD simulation
Basic equations
Commercial software (FLUENT, ANSYS) was used to simulate the microclimate and CO2 diffusion processes inside the greenhouse. Due to its sealed nature, the airflow within the greenhouse was primarily driven by natural convection, with the temperature difference between different locations serving as the main influencing factor. To verify the diffusion process of CO2 gas inside the greenhouse, unsteady simulations were used in this study. The ideal gas law was chosen to simulate air density change caused by the temperature difference, after which the actual measured temperatures and radiations of various boundaries were used to create a realistic temperature and natural convection environment. The governing equation for physical quantity φ (mass, energy and monument) can be written as follows30:
where xj and uj represent the coordinate (m) and velocity component (m s−1) in the jth direction, Γφ pertains to the diffusion coefficient of φ, and Sφ is the source term of φ.
The airflow inside the greenhouse was simulated using the standard k–ε model because it showed good accuracy in many dispersion simulations and greenhouse studies15,16,31,32,33,34,35. The discrete ordinates (DO) model was used to calculate the solar radiation inside the greenhouse, and the canopy was considered a semi-transparent medium with an absorption coefficient of 0.46 and a refractive index of 2.7736.
Crop models
The structure of a canopy can affect airflow, inducing a blocking effect. To simulate this effect, the canopy was used as a porous medium—the most common method for simulating crop canopy in CFD studies15,37. Using this method, the canopy-induced resistance could be converted into a sink term in the momentum equation, written as follows:
where \(\rho\) (kg m−3) is air density, LAD (m2 m−3) pertains to leaf area density defined as the leaf area index divided by the canopy height, v (m s−1) refers to the wind speed and D represents the drag coefficient. Notably, the constant 0.32 was adopted for D in this study because it has been applied in many simulation studies on greenhouse environments and showed good accuracy for different crops17,22,30,37,38.
The strawberry leaf transpiration can cause mass–energy exchange between the crop canopy and greenhouse environment, thereby altering environmental parameters such as humidity and temperature around the canopy. To simulate these processes, the leaf transpiration rate was calculated using plant physioecological process-based models39, which were also used to calculate canopy-generated water vapour, which was added to the simulation as a source term:
where Tr (kg m−2 s−1) is the leaf transpiration rate, \({g}_{aw}\) (mol m−2 s−1) is leaf-boundary-layer conductance to H2O, \({g}_{sw}\) (mol m−2 s−1) is stomatal conductance to H2O, VPD (kPa) is leaf-to-air vapour pressure deficit and Pa (101.3 kPa) is atmospheric pressure.
The heat absorbed by transpiration can be written in the following form and added to the simulation as a sink term of energy:
where H (J kg−1) is the heat of vapourisation.
Settings for CFD simulation
An ICEM-created unstructured mesh was used in this study, and 0.8, 1.2 and 1.5 million elements existed for Small, Long and Long + Wide greenhouses, respectively. The minimum orthogonal quality values for Small, Long and Long + Wide greenhouses were 0.3, 0.23 and 0.28; the maximum aspect ratios were 12.6, 14.9 and 13.4; skewness values were 0.69, 0.76 and 0.71, respectively.
In the simulation, temperature data obtained from actual measurements were used for all the parts inside the greenhouse. The air outlet of the CO2 generator was set as a mass flow inlet, and the airflow rate was obtained as follows:
where W (kg s−1) is the mass flow rate, ρa (kg m−3) is air density, Ao (m2) is the generator outlet area and va (m s−1) is the airflow velocity at the generator outlet.
Table 2 contains the specific settings and values for each boundary inside the greenhouse. Table 3 presents the physical parameters of the various materials used in the simulation. The average solar radiation amounts received by the canopy during the measurement (10 min) were 365, 178 and 204 W m−2 in Small, Long and Long + Wide greenhouses, respectively.
The SIMPLEC method and second-order upwind discretisation were used in simulations. The convergence criteria of residuals were automatically set by the software. The time step was set to 1 s to balance the calculation speed and accuracy.
Photosynthesis analysis
Model description
The photosynthetic rate of a single leaf (P) was simulated using plant–environment-combined mathematical models13. The model group comprised biochemical photosynthesis40, stomatal conductance41, and single-leaf transport models for CO2 and heat. Table 4 contains the specific values of the main parameters used in the model. For the photosynthetic rate calculation, P was detained by the hyperbolic minimum of the Rubisco-limited rate (Pc) and RuBP-limited rate (Pj).
where θA (0.99) represents the curvature in the transition from one limitation to the other, Vcmax (μmol m−2 s−1) represents the maximum rates of carboxylation, Ci (μmol mol−1) represents the leaf intercellular CO2 concentration, Γ* (μmol mol−1) represents the CO2 compensation point with no respiration, J (μmol m−2 s−1) represents the rate of electron transport dependent on light intensity, Kc (μmol mol−1) and Ko (μmol mol−1) represent the Michaelis constants for carboxylation and oxygenation (mmol mol−1), respectively, and O (mmol mol−1) represents the O2 concentration.
where I (μmol m−2 s−1) represents the photosynthetic photon flux density, Jmax (μmol m−2 s−1) represents the light-saturated rate of electron transport, ϕ (mol mol−1) represents the initial slope of the curve corresponding to the apparent quantum yield of the electron transport at low light conditions and θJ (0.85) represents the curve convexity.
According to the gas diffusion theory of Fick’s law, the relationship between leaf photosynthetic rate and CO2 diffusion for a single leaf could be written as follows:
where \({g}_{ac}\) represents the conductance of leaf-boundary-layer for CO2 transport, \({g}_{sc}\) represents the stomatal conductance for CO2, and Ca (μmol mol−1) and Cs (μmol mol−1) represent the CO2 concentration at the ambient air and leaf surface.
Following Medlyn et al.41, stomatal conductance for vapour (\({g}_{sw}\)) (mol m−2 s−1) could be calculated by:
where \({g}_{0}\) (mol m−2 s−1) represents the residual conductance and \({g}_{1}\) (3.21) represents the empirical constant. VPD (kPa) represents the leaf-air vapour pressure deficit.
The leaf-boundary-layer conductance (\({g}_{ah}\)) was calculated by the following equation:
where u represents wind speed and dleaf (0.064 m) represents the strawberry leave characteristic dimension. \({g}_{ah}\) can be expressed as \({g}_{ac}\) and \({g}_{aw}\) using \({g}_{ac}\)= \({g}_{aw}\)/1.37 and \({g}_{aw}\) = 1.08 \({g}_{ah}\).
In this study, the effect of CO2 enrichment on greenhouse photosynthetic capacity could be demonstrated by using the CFD-simulated CO2 concentration values to calculate the leaf photosynthetic rates. The model accuracy has been validated in a previous study (Kimura et al., 2020).
Spatial analysis of leaf photosynthetic rate
To quantitatively analyse the spatial distribution of the photosynthetic rate at the plane of 1.5 m height, which was close to the strawberry canopy inside each greenhouse, evenly distributed sampling points in each greenhouse were selected, separated by 2 m in the width direction and 1 m in the length direction (Fig. 4).
Due to the different areas of each greenhouse, 123, 255 and 511 sampling points were observed in Small Greenhouse, Long Greenhouse and Long + Wide Greenhouse, respectively.
Efficiency of CO2 enrichment
In order to quantitatively analyse the impact of CO2 enrichment on greenhouse overall photosynthetic capacity and energy utilisation efficiency, the efficiency of CO2 enrichment (ECE, mmol mol−1) was calculated. ECE was defined as the ratio of the increase in greenhouse photosynthetic capacity to the amount of CO2 used; the equation can be written as follows:
where Pa (mmol m−2 s−1) is the average leaf photosynthetic rates in the 1.5 m height plane, P400 (mmol m−2 s−1) is the leaf photosynthetic rate when the air CO2 concentration is 400 μmol mol−1, Ag (m2) is the greenhouse ground area and M (mol s−1) is the amount of energy consumption (equivalent to CO2).
Changes in ECE according to different levels of CO2 usage in the respective greenhouses were calculated. The enrichment effects with different levels of CO2 usage were simulated by changing the mass flow rate from the CO2 generator (from 0.05 to 0.5 kg s−1). After that, the average CO2 concentration in the 1.5 m height plane and the corresponding ECE were analysed for different levels of CO2 usage.
Ethical statement
The plant collection and use were in accordance with all the relevant guidelines.
Results and discussion
CFD simulation accuracy validation
Figure 5 shows the comparison of measured and CFD-simulated values of air temperature, relative humidity and CO2 concentration at corresponding measurement points for three greenhouses. The mean absolute errors of air temperature, relative humidity and CO2 concentrations were 1.3 °C, 6.9% and 79.2 μmol mol−1, indicating that the CFD simulations achieved good accuracy. Considering the accuracy obtained in previous studies21,22,29, the error values were within the normal range for CO2 simulation using CFD. These results demonstrate that the CFD model accurately simulated the diffusion process of CO2 in different greenhouses. In addition, the simulation results maintained good accuracy with different greenhouses under varying environmental conditions, indicating that the CFD model had good adaptability.
CO2 spatial distribution in the three greenhouses
Figure 6 demonstrates the CO2 concentration distribution inside the Small Greenhouse after 10 min enrichment. A significant concentration difference in the height direction of the greenhouse could be seen, which was caused by the upward convection of CO2 gas. Because CO2 was produced by combustion, it had a much higher temperature (65 °C) than the greenhouse air (27 °C), thereby causing CO2 gas to drift to the greenhouse’s upper part and gather there. Therefore, this could limit the effects of CO2 enrichment since the crops are located in the lower regions. However, the difference in CO2 concentration along the length direction was not so large due to its smaller size; the concentration at each location was maintained at ~ 1000 μmol mol−1. This had positive significance for maintaining a uniform CO2 concentration environment in the cultivation area.
Figure 7 demonstrates the CO2 concentration distribution inside the Long Greenhouse after 10 min enrichment. Given that this greenhouse used the same method to produce CO2, the same problem also occurred in the height direction near the CO2 generator. However, unlike the Small Greenhouse, a significant CO2 concentration gradient was observed along the length direction mainly due to the extremely long length (> 80 m) of the greenhouse. In the region near the generator, the CO2 concentration could reach ~ 1500 μmol mol−1, while in the region far from the generator, the CO2 concentration did not significantly increase. The uniformity of CO2 concentration distribution should directly influence the effect of CO2 enrichment7. Such uneven distribution could reduce the overall effect of increasing yield, posing difficulties in applying a reasonable control strategy of CO2 enrichment. In many modern greenhouses, environmental control devices are often regulated by real-time monitoring of environmental parameters, usually measured at one point (e.g. around greenhouse centre)13. For CO2 enrichment, setting relevant ranges to control the usage of CO2 generators is necessary, but uneven distribution makes it difficult to select the sampling points and target concentrations in greenhouses with longer lengths.
Figure 8 demonstrates the CO2 concentration distribution inside the Long + Wide Greenhouse after 10 min enrichment. The application of CO2 enrichment in this greenhouse produced quite different results from those in the previous two greenhouses. Notably, the CO2 concentration in most areas of the greenhouse did not increase significantly, mainly due to the huge volume of the greenhouse, being 4 and 2.5 times the volume of the Small and Long Greenhouses, respectively. Thus, the current application of CO2 for greenhouses with a large volume significantly failed to achieve good performance.
Because the strawberry canopy CO2 concentration is considered the most important factor when evaluating the effect of enrichment, the spatial distribution of CO2 concentration at the 1.5 m height plane was also analysed (Fig. 9). Figure 10 shows a statistical analysis of the CO2 concentration within the plane, revealing that the CO2 enrichment performance in the three greenhouses differed significantly. In the Small Greenhouse, the difference in CO2 concentration in the cultivation area was small, and the overall concentration was maintained at 900–1100 μmol mol−1. Given the absence of extremely high or low concentrations, the current measures of CO2 enrichment in this greenhouse achieved a relatively ideal state. In the Long Greenhouse, although the median and average values of CO2 concentration were both maintained at ~ 900 μmol mol−1, a relatively ideal state, obvious extreme values in the highest and lowest CO2 concentrations were observed. With the highest concentration reaching close to 1500 μmol mol−1, the lowest value stayed at 400 μmol mol−1 level. Notably, most of the recommended target CO2 concentration from the literature is between 600 and 1000 μmol mol−1 8,10,42,43, and excessive CO2 has a limited effect on promoting photosynthesis, indicating that the state for this greenhouse would reduce the efficiency of CO2 enrichment. Therefore, the primary improvement requirement for this greenhouse type is to achieve a more uniform distribution of CO2 concentration with the interior. In the Long + Wide Greenhouse, the problem was mainly that the effect of CO2 enrichment was not noticeable. Although some areas had a CO2 concentration of 1000 μmol mol−1 near the CO2 generator, the overall CO2 concentration level of the cultivation area remained around 400 μmol mol−1. Therefore, the primary improvement should be increasing CO2 concentration in the greenhouse.
Analysis of leaf photosynthetic rate in three greenhouses
The biochemical process of leaf photosynthesis should be considered when conducting CO2 enrichment within greenhouses7,13. Figures 11 and 12 illustrate the spatial distribution and statistics of the leaf photosynthetic rate at the 1.5 m height plane for the three greenhouses, respectively, intuitively revealing the effect of increasing CO2 concentration on crop photosynthesis. Given the constancy assumption of environmental parameters other than the CO2 concentration, the distribution of leaf photosynthetic rate was attributed to the CO2 concentration distribution. The photosynthetic rate was unevenly distributed in the Long and Long + Wide Greenhouses compared to the Small Greenhouse, possibly explaining why an insignificant increasing effect of CO2 enrichment was observed in those greenhouses. Considering the overall photosynthetic rate variations in the greenhouses, the average values for the three greenhouses increased by 28.7%, 23.4% and 7.4%, respectively, for the Small, Long and Long + Wide Greenhouses, compared to their status under the condition of CO2 concentration at 400 μmol mol−1. As shown in Fig. 12, the difference in the photosynthetic rate at respective locations in the Small Greenhouse was extremely small, as most areas had photosynthetic rates staying above the 16 μmol m−2 s−1 level. In the Long Greenhouse, the maximum value of the photosynthetic rate changed slightly compared to the Small Greenhouse, which can be attributed to the nonlinear relationships between the photosynthetic rate and CO2 concentration, although an obvious variation existed in the uniformity of the photosynthesis rate. In addition, only half of the area had a photosynthetic rate exceeding 16 μmol m−2 s−1, and the lowest photosynthetic rate reached a level close to 13 μmol m−2 s−1. In the Large + Wide Greenhouse, the uneven distribution of photosynthetic rate still existed, and the effect of increasing this rate significantly dropped to 12.5 μmol m−2 s−1. More than half of the area had photosynthetic rates below 13 μmol m−2 s−1.
ECE analysis in three greenhouses
Figure 13 demonstrates the change in average CO2 concentration in the 1.5 m height plane and CO2 use efficiency under different amounts of pure CO2 gas (mol) enriched in the greenhouse. Although most researchers have provided an estimated range of suitable CO2 concentrations 600–1000 μmol mol−1 8,10,42,43, clarifying the changes in greenhouse photosynthetic capacity and energy use efficiency under different CO2 usage conditions is needed for improved performance and efficiency. The average CO2 concentration over the greenhouse plane exhibited an obvious linear relationship with CO2 usage (Fig. 13). The resulting slope gradually became smaller as the volume increased because the greenhouses had volume variations. Another important factor affecting the concentration change is that the inhomogeneity (standard deviation) of CO2 concentration in the cultivation planes of the Small and Long + Wide Greenhouses was almost constant despite variations in the amount of CO2 usage. In contrast, the inhomogeneity in the Long Greenhouse increased significantly as the CO2 usage increased. Their geometric features could cause this kind of difference, and it mainly depended on the area and aspect ratio (length: width).
Due to its smaller area, the Small Greenhouse exhibited a more uniform distribution of CO2 concentration, resulting in a smaller constant inhomogeneity. The Long + Wide Greenhouse had a similar aspect ratio but a larger area than the Small Greenhouse. As a result, it had a larger inhomogeneity but also at a constant. The main reason for this is that in the cultivation plane, CO2 diffusion can be considered a two-dimensional transport along with the greenhouse length and width directions. Therefore, greenhouses with similar aspect ratios have similar transport conditions, leading to constant inhomogeneities in both the Small and Long + Wide Greenhouses. However, the Long + Wide Greenhouse had a much larger area, which would cause a more serious concentration difference in the cultivation plane and result in a higher standard deviation in CO2 concentration. In contrast, the Long Greenhouse had an extremely higher aspect ratio than the other two greenhouses, which would limit the diffusion in the width direction. Therefore, CO2 diffusion can be seen as a one-dimensional transport along with greenhouse length. In addition, due to the dominance of CO2 gas generation over CO2 diffusion in terms of performance, CO2 gas tended to accumulate near the generator, particularly at the front. Consequently, as the amount of CO2 usage increased, the standard deviation of CO2 concentration expanded, reflecting the accumulation effect.
Notably, the ECE generally decreased as the CO2 usage increased. The two main reasons for the change in efficiency are as follows. First, a nonlinear relationship existed between leaf photosynthetic rate and CO2 concentration. When the CO2 concentration was initially low, increasing it could markedly enhance the photosynthetic rate, but as the concentration continued to rise, the effect gradually decreased44, resulting in reduced ECE. In response to this problem, maintaining the concentration in the cultivation area at a lower level seems to be more efficient under the current enrichment method. Second, the spatial distributions of CO2 concentration and photosynthetic rates within greenhouses are a potential reason. When the amount of usage was small, CO2 gas was mainly concentrated in the upper part of the greenhouses, so an increase in the concentration around the cultivation area (at 1.5 m height) was insignificant. As a result, the ECE became relatively low. As the amount of CO2 usage increased, more CO2 gas diffused from the upper part of the greenhouses to the cultivation area, and then efficiency was improved. Nevertheless, when further CO2 enrichment was continued, a significant portion of the CO2 gas was allocated to increasing the concentration in noncultivation spaces. This allocation is likely to have adverse effects on overall ECE.
Eco-friendly strategy for CO2 enrichment in commercial greenhouses
By analysing the CO2, leaf photosynthetic rate distribution and ECE variations in different commercial greenhouses, the following problems were identified for the use of CO2 enrichment in commercial production:
The first is the uneven distribution of CO2 in the cultivation area. Using circulation fans to provide air movement seems to be an ideal method for solving this problem45. However, in this study, the cultivators did not use circulation fans in the greenhouses, possibly due to anticipated pest control difficulties. In addition, when using circulation fans, the airflow created by the circulation fans must be maintained at proper strength to avoid high wind speed damage to crops46.
Second, the existing enrichment method could not achieve a desirable increase in CO2 concentration in large-scale greenhouses. Therefore, burning more fuel to produce more CO2 from the generator seems the easiest way to solve this problem. However, simply increasing the CO2 supply from one generator may not be an ideal improvement measure because it would induce a serious uneven distribution of CO2, same with the Long Greenhouse. Therefore, increasing the number of CO2 generators and reasonably arranging their locations may be a better choice. In this case, more generators can ensure sufficient CO2 supply, and reducing the spacing between generators could effectively prevent evident CO2 unevenness inside the greenhouse.
Third, the limited distribution of CO2 at the height direction is another problem. Because the high temperature of CO2 gas caused this problem, lowering its temperature is the most direct solution. Zhang et al.14 proved the effectiveness of this measure in improving the distribution of CO2 in the height direction using CFD simulation.
Finally, through the quantitative analysis of ECE under different amounts of CO2 usage, setting the target CO2 concentration at a lower level of approximately 500 μmol mol−1 may be a better choice from an energy-efficiency perspective.
The above discussion of improvement measures was based on continually using the existing CO2 enrichment method. Various improvement measures may improve the application effect to a certain extent, but fundamental improvement is not guaranteed. Therefore, to make a qualitative change in the performance of CO2 enrichment in commercial production, the enrichment method needs to be fundamentally changed. A recently proposed new enrichment method (i.e. crop-local enrichment) may be an ideal solution14,24,26,27, as it enables CO2 gas transport to the cultivation area while directly releasing it into the crop canopy, thereby creating the highest CO2 concentration environment just around the strawberry canopy while ensuring good uniformity in the cultivation area.
Conclusion
Spatial distribution of photosynthesis and CO2 within greenhouses under the CO2 enrichment was visualised using a CFD simulation–photosynthetic model. These distributions were characterised by the geometric features of greenhouses. Namely, the average value of CO2 concentration and photosynthetic rate decreased due to greenhouse scale from Small to the Large + Wide tests design issues, and the uniformity of their distribution deteriorated as the aspect ratio increased. In particular, for the Long Greenhouse, due to an imbalance of capacities of CO2 gas generation and transport, some areas had concentrations below and above the target concentration. However, most areas in the Long Greenhouse had a photosynthetic rate same as that of the Small Greenhouse, which can be attributed to the saturated relationship between photosynthetic rate and CO2 concentration. Furthermore, ECE peaked when the average CO2 concentration in the cultivation area was ~ 500 μmol mol−1 for Long and Long + Wide Greenhouses, and a subsequently continuous increase in the CO2 concentration would reduce efficiency. Considering the CO2 enrichment problems observed in commercial production, setting the target CO2 concentration to around 500 μmol mol−1 seems reasonable. Other measures, such as daytime running of circulation fans and crop-localised CO2 enrichment, could also be better choices, although they are yet to receive widespread applications in commercial greenhouses.
Data availability
The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.
References
Hao, P.-F. et al. Agriculture organic wastes fermentation CO2 enrichment in greenhouse and the fermentation residues improve growth, yield and fruit quality in tomato. J. Clean. Prod. 275, 123885 (2020).
Luo, Y., Long, X., Wu, C. & Zhang, J. Decoupling CO2 emissions from economic growth in agricultural sector across 30 Chinese provinces from 1997 to 2014. J. Clean. Prod. 159, 220–228 (2017).
de Ridder, F., van Roy, J., de Schutter, B. & Mazairac, W. An exploration of shared heat storage systems in the greenhouse horticulture industry. Energy 235, 121425 (2021).
Subahi, A. F. & Bouazza, K. E. An intelligent IoT-based system design for controlling and monitoring greenhouse temperature. IEEE Access 8, 125488–125500 (2020).
Fox, J. A., Adriaanse, P. & Stacey, N. T. Greenhouse energy management: The thermal interaction of greenhouses with the ground. J. Clean. Prod. 235, 288–296 (2019).
Costantino, A., Comba, L., Sicardi, G., Bariani, M. & Fabrizio, E. Energy performance and climate control in mechanically ventilated greenhouses: A dynamic modelling-based assessment and investigation. Appl. Energy 288, 116583 (2021).
Li, Y., Ding, Y., Li, D. & Miao, Z. Automatic carbon dioxide enrichment strategies in the greenhouse: A review. Biosyst. Eng. 171, 101–119 (2018).
Panwar, N. L., Kaushik, S. C. & Kothari, S. Solar greenhouse an option for renewable and sustainable farming. Renew. Sustain. Energy Rev. 15, 3934–3945 (2011).
Kimball, B. A. Crop responses to elevated CO2 and interactions with H2O, N, and temperature. Curr. Opin. Plant Biol. 31, 36–43 (2016).
Bisbis, M. B., Gruda, N. & Blanke, M. Potential impacts of climate change on vegetable production and product quality—A review. J. Clean. Prod. 170, 1602–1620 (2018).
Sánchez-Guerrero, M. C. et al. Effect of variable CO2 enrichment on greenhouse production in mild winter climates. Agric. For. Meteorol. 132, 244–252 (2005).
Kuroyanagi, T., Yasuba, K., Higashide, T., Iwasaki, Y. & Takaichi, M. Efficiency of carbon dioxide enrichment in an unventilated greenhouse. Biosyst. Eng. 119, 58–68 (2014).
Kimura, K., Yasutake, D., Koikawa, K. & Kitano, M. Spatiotemporal variability of leaf photosynthesis and its linkage with microclimates across an environment-controlled greenhouse. Biosyst. Eng. 195, 97–115 (2020).
Zhang, Y., Yasutake, D., Hidaka, K., Kitano, M. & Okayasu, T. CFD analysis for evaluating and optimizing spatial distribution of CO2 concentration in a strawberry greenhouse under different CO2 enrichment methods. Comput. Electron. Agric. 179, 105811 (2020).
Kichah, A., Bournet, P.-E., Migeon, C. & Boulard, T. Measurement and CFD simulation of microclimate characteristics and transpiration of an Impatiens pot plant crop in a greenhouse. Biosyst. Eng. 112, 22–34 (2012).
Bartzanas, T., Boulard, T. & Kittas, C. Numerical simulation of the airflow and temperature distribution in a tunnel greenhouse equipped with insect-proof screen in the openings. Comput. Electron. Agric. 34, 207–221 (2002).
Bouhoun Ali, H., Bournet, P.-E., Cannavo, P. & Chantoiseau, E. Development of a CFD crop submodel for simulating microclimate and transpiration of ornamental plants grown in a greenhouse under water restriction. Comput. Electron. Agric. 149, 26–40 (2018).
Kim, K. et al. 3-D CFD analysis of relative humidity distribution in greenhouse with a fog cooling system and refrigerative dehumidifiers. Biosyst. Eng. 100, 245–255 (2008).
Zhang, G. et al. Nonlinear simulation for coupling modeling of air humidity and vent opening in Chinese solar greenhouse based on CFD. Comput. Electron. Agric. 162, 337–347 (2019).
Bournet, P.-E. & Boulard, T. Effect of ventilator configuration on the distributed climate of greenhouses: A review of experimental and CFD studies. Comput. Electron. Agric. 74, 195–217 (2010).
Roy, J. C., Pouillard, J. B., Boulard, T., Fatnassi, H. & Grisey, A. Experimental and CFD results on the CO2 distribution in a semi closed greenhouse. Acta Hortic https://doi.org/10.17660/ActaHortic.2014.1037.131 (2014).
Boulard, T., Roy, J.-C., Pouillard, J.-B., Fatnassi, H. & Grisey, A. Modelling of micrometeorology, canopy transpiration and photosynthesis in a closed greenhouse using computational fluid dynamics. Biosyst. Eng. 158, 110–133 (2017).
Puglisi, G., Vox, G., Campiotti, C. A., Scarascia Mugnozza, G. & Schettini, E. Experimental results of a solar cooling system for greenhouse climate control. Acta Hortic. 1296, 1107–1114 (2020).
Zhang, Y. et al. Crop-localised CO2 enrichment improves the microclimate, photosynthetic distribution and energy utilisation efficiency in a greenhouse. J. Clean. Prod. 371, 133465 (2022).
Achour, Y., Ouammi, A. & Zejli, D. Technological progresses in modern sustainable greenhouses cultivation as the path towards precision agriculture. Renew. Sustain. Energy Rev. 147, 111251 (2021).
Miyoshi, Y., Hidaka, K., Okayasu, T., Yasutake, D. & Kitano, M. Effects of local CO2 enrichment on strawberry cultivation during the winter season. Environ. Control Biol. 55, 165–170 (2017).
Hidaka, K. et al. Crop-local CO2 enrichment improves strawberry yield and fuel use efficiency in protected cultivations. Sci. Hortic. 301, 111104 (2022).
Ghiat, I., Mahmood, F., Govindan, R. & Al-Ansari, T. CO2 utilisation in agricultural greenhouses: A novel ‘plant to plant’ approach driven by bioenergy with carbon capture systems within the energy, water and food Nexus. Energy Convers. Manag. 228, 113668 (2021).
Molina-Aiz, F. D. et al. Using computational fluid dynamics to analyse the CO2 transfer in naturally ventilated greenhouses. Acta Hortic. https://doi.org/10.17660/ActaHortic.2017.1182.34 (2017).
Nebbali, R., Roy, J. C. & Boulard, T. Dynamic simulation of the distributed radiative and convective climate within a cropped greenhouse. Renew. Energy 43, 111–129 (2012).
Kiša, M. & Jelemenský, Ľ. CFD dispersion modelling for emergency preparadnes. J. Loss Prev. Process Ind. 22, 97–104 (2009).
Scargiali, F., Grisafi, F., Busciglio, A. & Brucato, A. Modeling and simulation of dense cloud dispersion in urban areas by means of computational fluid dynamics. J. Hazard. Mater. 197, 285–293 (2011).
Xing, J. et al. Experimental and numerical study of the dispersion of carbon dioxide plume. J. Hazard. Mater. 256–257, 40–48 (2013).
Liu, B. et al. Computational fluid dynamics simulation of carbon dioxide dispersion in a complex environment. J. Loss Prev. Process Ind. 40, 419–432 (2016).
He, X. et al. Ventilation optimization of solar greenhouse with removable back walls based on CFD. Comput. Electron. Agric. 149, 16–25 (2018).
Fidaros, D. K., Baxevanou, C. A., Bartzanas, T. & Kittas, C. Numerical simulation of thermal behavior of a ventilated arc greenhouse during a solar day. Renew. Energy 35, 1380–1386 (2010).
Boulard, T. & Wang, S. Experimental and numerical studies on the heterogeneity of crop transpiration in a plastic tunnel. Comput. Electron. Agric. 34, 173–190 (2002).
Teitel, M., Ziskind, G., Liran, O., Dubovsky, V. & Letan, R. Effect of wind direction on greenhouse ventilation rate, airflow patterns and temperature distributions. Biosyst. Eng. 101, 351–369 (2008).
Gaastra, P. Photosynthesis of Crop Plants as Influenced by Light, Carbon Dioxide, Temperature, and Stomatal Diffusion Resistance (Wageningen University, 1959).
Farquhar, G. D., von Caemmerer, S. & Berry, J. A. A biochemical model of photosynthetic CO2 assimilation in leaves of C3 species. Planta 149, 78–90 (1980).
Medlyn, B. E. et al. Reconciling the optimal and empirical approaches to modelling stomatal conductance. Glob. Change Biol. 17, 2134–2144 (2011).
Mortensen, L. M. Review: CO2 enrichment in greenhouses. Crop responses. Sci. Hortic. 33, 1–25 (1987).
Nederhoff, E. M. Effects of CO2 Concentration on Photosynthesis, Transpiration and Production of Greenhouse Fruit Vegetable Crops (Wageningen University, 1994).
Rogers, H. H., Runion, G. B. & Krupa, S. V. Plant responses to atmospheric CO2 enrichment with emphasis on roots and the rhizosphere. Environ. Pollut. 83, 155–189 (1994).
Kuroyanagi, T. Evaluation indicator for greenhouse air circulator performances. Eng. Agric. Environ. Food 6, 197–202 (2013).
Shibuya, T., Shinto, Y., Endo, R. & Kitaya, Y. Far-red light interacts with wind-induced stress in cucumber seedlings. Sci. Hortic. 295, 110805 (2022).
Acknowledgements
This study was supported by the Projects of the On-farm Demonstration Trials of Smart Agriculture from the Ministry of Agriculture, Forestry and Fisheries (19189416, 21451798) (National Agriculture and Food Research Organisation), the Cabinet Office grant in aid, the Advanced Next-Generation Greenhouse Horticulture by IoP (Internet of Plants), Japan, and the Grant in Aid for Scientific Research (No. 21H02318) from the Japan Society for the Promotion of Science. The authors would like to gratefully acknowledge Mr. Tanaka, Mr. Otsu, and Mr. Sonoda, for providing the experimental greenhouses and help during the measurement. The authors also thank Fuka Arakawa and Hiromi Nakai for their kind helps during the observations.
Author information
Authors and Affiliations
Contributions
Y. Z., D. Y., and K. H. conducted the experiments and wrote the manuscript. K. K., T. O., M. K., and T. H. reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhang, Y., Yasutake, D., Hidaka, K. et al. Eco-friendly strategy for CO2 enrichment performance in commercial greenhouses based on the CO2 spatial distribution and photosynthesis. Sci Rep 13, 17277 (2023). https://doi.org/10.1038/s41598-023-44200-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-44200-9
- Springer Nature Limited