Abstract
The coupling environment of temperature (T) and lateral pressure at great depths promotes intact rocks to shear failure, posing a serious threat to underground engineering. Temperature effect on shear behaviour is of particular importance due to the possible mineralogical alterations in mineral composition, especially in clay-rich rocks such as mudstone that has a great affinity for water. Accordingly, the effect of thermal treatment on the shear behaviour of intact mudstone was investigated, in this study, using the Short Core in Compression (SSC) method. Three temperatures of RT, 250 and 500 °C, and four lateral pressures of 0.0, 0.5, 2.0, and 4.0 MPa were adopted. Numerical and experimental observations showed that the resulting fractures in SCC samples are shear and by increasing the lateral pressure, shear failure is promoted. Compared with other rock types such as granite and sandstone, shear properties in mudstone have only one positive trend with temperature increase up to 500 °C, by increasing T from RT to 500 °C, mode II fracture toughness, peak friction angle, and the cohesion increased by about 15 to 47%, 4.9%, and 47.7%, respectively. The bilinear Mohr–Coulomb failure criterion can be used to model the peak shear strength behaviour of intact mudstone before and after thermal treatment.
Similar content being viewed by others
Introduction
The earth’s crust is exposed to many environmental factors that might threaten the safety and stability of geological structures, surface, and underground infrastructures. Due to the change caused by temperature on the mineral composition and degree of cracking induced by thermal stress1,2,3, the temperature is one of the most important factors directly affecting the mechanical behaviour of geological structures including intact rocks and fracture networks. Taking into account the coupling effect of temperature and lateral pressure at greater depths, where the average rate of increase in temperature with depth is 3–5 °C/100 m4, intact rocks become more prone to shear failure5 which causes a severe threat to deep engineering6. Therefore, investigating the temperature-dependent shear behavior of intact rocks is of great importance to analyze the safety and stability of underground engineering structures under the condition of thermo-mechanical (TM) coupling.
Numerous contributions have been made by many scholars to analyze rock behavior under thermal treatment effects. Here we highlight recent works related to the temperature-dependent shear behavior of intact rocks, which is the focus of the current research. Shao et al.7 investigated the mechanical behaviour of intact granite under in-situs stress and temperature conditions using cylindrical rock specimens. They concluded a reduction in shear parameters by increasing the temperature, and the conventional Mohr–Coulomb criterion failed to model shear behavior under geothermal reservoir conditions. Zhai et al.8 studied shear characteristics of healed joints and intact granite after thermal treatment and showed that the ductile failure characteristics of these joints after high-temperature thermal treatment are greater than that in intact rocks. In addition, they pointed out that dilation angle, shear stiffness, and peak shear strength are positively correlated with temperature up to 400 °C, and negatively correlated with T greater than 400 °C. Chen et al.6 investigated the shear behavior of intact cubic specimens of granite under thermo-mechanical coupling and showed that the internal friction angle and cohesion significantly decreased with an increase in the temperature, while the roughness of resulting fracture was directly proportional to temperature increase. Zhu et al.9 showed that the cohesion and internal friction angle of intact cylindrical specimens of granite reduces with temperature, decreasing rapidly by 49.39% and 27.51% from 500 to 600 °C respectively. The effect of thermal treatment on the shear behavior of intact sandstone was investigated by Liu et al.10. They concluded that the shear strength first increases before 600 °C and decreases after 600 °C, the shear modulus varies slightly before 600 °C and decreases rapidly after 600 °C. Yin et al.11 studied the shear mechanical behavior of intact sandstone after thermal treatment at temperatures between 100 and 800 °C. They pointed out that due to decreasing peak shear strength and enhanced ductility for temperatures between 400 and 800 °C, the secant peak shear stiffness declined by 43.79–70.48%.
It can be noted that most research related to the effect of temperature on the shear behaviour of intact rocks were conducted on igneous rocks such as granite. While sedimentary rocks such as sandstone, limestone, and mudstone that are closely located above and below oil and gas reservoirs and coal beds12 have received less attention. Moreover, clay-rich rocks such as mudstone are widely distributed in the earth's crust, accounting for approximately 30% of the surface rocks13,14. These rock types have a great affinity for water due to the formation of a diffuse double layer around the negatively charged clay minerals, this makes the mechanical properties of these rocks unique and more complicated when exposed to temperature effects15,16,17. Some attempts were conducted to investigate the compressive and tensile behaviour of mudstone after thermal treatment12,16,17,18,19,20,21,22,23,24,25, and concluded that tensile and compressive properties improve to a certain temperature (400 and 600 °C) due to drying of clay minerals during thermal treatment, and then decrease after this limit. On the other hand, the effect of thermal treatment on shear behaviour of intact mudstone needs a comprehensive study and extensive efforts. Therefore, the novelty of this study comparing with the existing literature lies on the coupling effect of temperature and lateral pressure on shear behavior of clay rich rocks in its intact form. Shear behavior of intact mudstone after thermal treatment was investigated following the flowchart shown in Fig. 1 which visualizes the steps taken to develop this study.
Methods
The effect of thermal treatment on the shear behaviour of intact mudstone was investigated by using the Short Core in Compression (SCC) test. Two methods were adopted to achieve the goal of the current research, numerical and experimental methods. The numerical method was used to simulate the SCC sample to obtain stress fields and mode II stress intensity factor (KII) under uniaxial and lateral stress states, and to judge the type of the resulting fracture, whether is it a tensile or shear fracture. While the experimental method was used to obtain real results for the effect of thermal treatment on shear characteristics of intact mudstone.
Numerical simulation of SCC test
Short core in compression samples were used in this study to investigate the effect of temperature and lateral pressure on the shear properties of intact mudstone. These samples were utilized here to simulate a continuous and intact rock bridge under shear forces, such that the new fracture grows in the rock bridge under pure shear stress. This bridge is subjected to normal and shear stresses and reflects the properties of the intact material. Short core in compression test is generally used to investigate shear fractures that grow between tips of two horizontal notches. In the beginning, Watkins and Liu26 developed the Short Beam in Compression (SBC) test by using squared pillars shown in Fig. 2a. Since squared pillars require extensive machining work compared to cylindrical specimens that can be easily prepared by extracting a core from a rock block, Jung et al.27 suggested Short Core in Compression (SCC) test shown in Fig. 2b. The advantage of these samples is the possibility of applying lateral pressure by using Hoek cell to investigate shear fractures under different values of horizontal stress σH (Fig. 2c). To obtain stress fields over the entire rock sample and stress intensity factor KII at the notch tip, the SCC test was numerically modeled using the Displacement Discontinuity Method (DDM) which is a branch of the Boundary Element Method (Fig. 2d). In this method, boundaries of the rock sample are divided into N DDM elements, and each element is subjected to two types of boundary conditions that include normal stress σn, shear stress σs, normal displacement un, and/or shear displacement us. A system of algebraic equations (N × N) is formed between boundary conditions and displacement discontinuities (Dn and Ds) and by solving this system, Dn and Ds are obtained for each element. Where Dn and Ds are normal and shear displacement discontinuities, respectively. Normal displacement discontinuity Dn can be defined as the difference in normal displacement un between the two sides of the DDM element. A positive Dn means that the DDM element is under compression and the element surfaces approach each other, and vice versa for negative Dn. Shear displacement discontinuity Ds can be defined as the difference in shear displacement us between the two sides of the segment, and the positive value of Ds means that the upper surface moves to the left relative to the lower surface (left lateral slip). Finally, stress components, displacements, and stress intensity factors at the midpoint of each element are calculated as a function of Dn and Ds28. By using the DDM method, a numerical code was developed in our previous works to predict fracture path, stress fields, and stress intensity factors in different rock samples18,19,20,29. This code was extended in this study to model the SCC test under uniaxial and confined stress states. Based on the simulation that is shown in Fig. 7 and the experiments conducted by previous researchers on SCC specimens27,30,31, the maximum shear stress concentrates at the tips of the two notches and shear fracture initiates and begins to grow perpendicular to these notches.
Based on the fracture mechanics theory in linear elastic fracture mechanics32,33, determining the stress intensity factor KII involves modelling the development of a secondary shear crack from the notch tip, which is the initiation point for the growth of the shear fracture (Fig. 3a). In other rock specimens that are used to generate shear fractures under both mode II loading and mode II initiation such as shear box and punch-through shear (PTS) specimens, a secondary shear crack is not necessary for simulation analysis to obtain the KII because the new crack plane is along the notch plane. While in the SCC specimen, the plane of the new shear crack is perpendicular to the notch plane. Yao et al.31 pointed out that the maximum shear stress concentrates along the vertical bridge between two notch tips and it is maximized at these tips, the fracture initiates at lower and upper notch tips, and secondary shear cracks are required to calculate KII. Moreover, by using the digital image correlation technique on SCC samples of granite, Zhang et al.34 found that new cracks first initiate from two notch tips and then propagate toward the central area in the expected shear fracture band. To apply the traditional fracture mechanics theory to the SCC specimen, the secondary shear crack is necessary for accurately determining the stress intensity factor in the fracture process, and the KIIC can be further determined precisely when a crack tip exists along the shear bridge between tips of the two horizontal notches35,36. Accordingly, a secondary shear crack with length hc was modeled in this study and divided into Nc elements, the final element was treated as a crack tip element. Displacement discontinuities (DnTip and DsTip) were calculated at the crack tip element and the mode II stress intensity factor KII was obtained as a function of the shear displacement discontinuity (DsTip) using the following equation of Shou and Crouch37:
where G and ν are shear modulus and Poisson’s ratio, respectively. DsTip is the shear displacement discontinuity at the crack tip element. ae is half the length of the crack tip element. Figure 3b shows mode II stress intensity factor KII as a function of σV, σH, and C/H ratio. Figure 3b shows that the KII is not affected by the lateral stress σH, this is because KII is mainly a function of the shear stress at the secondary shear crack tip (DsTip = f(σxyTip)), and as observed in the numerical model in Fig. 7, when the lateral stress σH is increased, the shear stress along the bridge between two notches remains constant. In addition, Fig. 3b shows that the KII increases with increasing the vertical stress σV, and it is inversely proportional to the C/H ratio. These results are in complete agreement with the numerical observations of Xu et al.30 and Yao et al.31 obtained using the FEM method.
Experimental procedure
The objective of this research is to examine how temperature and lateral pressure impact shear fractures in clay-rich rocks. Therefore, it was essential to choose a rock type that is abundant in clay to meet the aim of this study. As a result, mudstone rock was chosen due to its mineral composition and grain size distribution as depicted in Fig. 4a. The gray and white shades in the original section of Fig. 4a symbolize clay and calcite, respectively. While the black color represents voids and pores. The proportion of these components was determined through color analysis using ImageJ software. The mudstone sample used in this study is composed of 92.75% clay, 7% calcite, and 0.25% voids and pores. Moreover, the grain size distribution shown in Fig. 4b was determined using ImageJ and @Risk software. It is worth mentioning that 90% of the mudstone sample used in this research is made up of grains with sizes ranging from 8.93 to 27.81 μm. ImageJ is a public-domain Java image processing program inspired by NIH Image. This software can be used to measure grain sizes due to the following features; ImageJ can calculate area and pixel value statistics of user-defined selections, measure distances and angles, create density histograms and line profile plots, supports standard image processing functions such as contrast manipulation, sharpening, smoothing, edge detection and median filtering. @RISK software is an add-in tool for Microsoft Excel that helps to make better decisions through risk modeling and analysis. This software has 33 distribution functions that can be used to determine grain size distribution.
The physical and mechanical properties of the mudstone tested in this study are summarized in Table 1. These properties were measured in this study according to established standards in rock mechanics (ISRM)38. As shown in this table, the mudstone used in this study is characterized by low porosity of 0.664%, relatively low tensile strength of 3.2 MPa, and high compressive strength of 109 MPa.
Sample preparation
Figure 5 shows the stages of preparation of the rock samples. To ensure homogeneity between samples, all samples were prepared from the same rock block. Figure 5a shows a group of prismatic samples of the mudstone taken from a single block. Then the prismatic samples were transformed into cylindrical samples with a diameter of 5 cm through a process of rotating, carving, and polishing (Fig. 5b). The resulting samples were divided into smaller specimens with a height of 10 cm so that the ratio of height to diameter is 10/5 = 2 (Fig. 5c). The cylindrical rock specimens in Fig. 5c were prepared according to ASTM D7012, where the length-to-diameter ratio (H/D = 2), and the cylindrical surfaces are prepared to be flat and smooth. In particular, the sample’s ends must be leveled within a 0.02 mm tolerance and they should not depart from perpendicularity by more than 0.06 degrees. To obtain SCC samples, two parallel notches were made in each cylindrical specimen according to the dimensions shown in Fig. 5d. These measurements were chosen as a result of the numerical analysis outlined in this study, and depending on previous investigations of Jung et al.27 and Xu et al.30.
The SCC samples were subjected to thermal treatment using the furnace depicted in Fig. 5e. This furnace has a maximum temperature of 1200 °C and a heating rate of 4.2 °C per minute. The SCC samples were divided into three groups: the first group was not thermally treated and was tested at room temperature (RT). The second and third groups were heated in the furnace for 24 h at temperatures of 250 and 500 °C, respectively. As will be explained later, the maximum temperature of 500 °C was adopted here as the maximum temperature below which no thermal fractures were observed on the mudstone surface. Thermal fractures greatly affect the continuity and properties of SCC samples, which makes these samples heterogeneous and the obtained results more dispersed. Once the 24 h were over, the furnace was turned off and the temperature was allowed to decrease back to room temperature. To prevent thermal shock, the samples were heated and cooled gradually. As shown in Fig. 5f and Fig. 5g, the SCC samples’ color changed depending on the thermal treatment temperature. The original beige color of the mudstone samples at RT changed to a light creamy color after treatment at 250 °C. While after 24 h in a furnace at a temperature of 500 °C, the SCC samples acquire a gray color (cement color). As will be shown later, these color changes are due to the formation/decomposition of calcium compounds and clay minerals which are the main components of the mudstone.
Experimental apparatus
The SCC samples were tested under uniaxial and confined stress states using a servo-hydraulic machine shown in Fig. 6. The machine used is a GOTECH AI-7000 LA 20 with a capacity of 20 T and a vertical displacement speed range of 0.0001 to 250 mm/min. All SCC samples were tested under a vertical speed of 1 mm/min so that the resulting strain rate was 1.7 × 10–4 S−1. A hydraulic pump with a Hoek cell was used to apply three levels of lateral pressure, 0.5, 2, and 4 MPa. The lateral pressure was maintained constant until the point of fracture and it was monitored and recorded via a PC connected to the hydraulic pump.
Results and discussion
Shear and maximum principal stress fields predicted by numerical method
Distribution of shear stress σxy and maximum principal stress σmax over the entire SCC sample as a function of stress ratio λ = σH/σV is shown in Fig. 7. In numerical calculations used to obtain stress fields in this figure, σV was constant equal to 1 MPa, but σH was changed from 0.0 to 0.25, 0.5, 0.75 and 1.0 MPa to obtain stress ratio λ from 0.0 to 1.0. Figure 7 shows that the shear stress σxy concentrates along the bridge between tips of the two horizontal notches. Note that, the distribution and magnitude of σxy is not affected by increasing stress ratio λ. Moreover, the maximum value of shear stress along the bridge between the two notches σxy(Bridge) is constant and equals 2.83 MPa for λ from zero (uniaxial case) to λ = 1 (hydrostatic case). The maximum principal stress σmax was monitored and it can be noted that this stress forms an inclined bridge between the tips of the two horizontal notches, and it is positive indicating tensile stress development along this bridge, which may result in the growth of the tensile fracture instead of the shear fracture between the two notches. Therefore, the resulting fracture must be evaluated to determine if it is a shear fracture due to σxy or tensile fracture due to σmax. In general, shear fractures are vertical between the tips of the two notches, while tensile fractures are inclined to the right relative to the vertical long axis of the SCC sample. In addition, the surface of shear fractures is smoother and flatter than the tensile fractures, especially when the lateral pressure σH is applied39. Additionally, Fig. 7 shows that the distribution (width of the stress zone) and magnitude of σmax decreases with increasing the stress ratio λ. The maximum value of σmax along the bridge between tips of the two notches σmax(Bridge) decreases by about 38% when the λ increases from zero to one. Therefore, by exerting lateral pressure on SCC samples, the impact of tensile stress is reduced and the growth of shear fractures is promoted.
Displacement load curves
The SCC samples were tested under three temperatures (RT ≈ 25, 250, and 500 °C) and four levels of lateral pressure (0.0, 0.5, 2, and 4 MPa) with three tests conducted for each condition, resulting in a total of 36 tests. The load–displacement curves under RT, 250 and 500 °C (for the four lateral pressures) are shown in Fig. 8a–c, respectively. To simplify the presentation and comparison of results, one load–displacement curve was presented for every three replicate tests (one curve per lateral pressure). Figure 8 illustrates that as the temperature and lateral pressure increase, the peak (fracture load) and the area under the load–displacement curve also increase. A higher peak indicates greater resistance to fracture growth. However, a larger area under the curves indicates a greater amount of strain energy stored in the rock sample before the fracture instant, which greatly impacts the speed of the fracture growth between the tips of the two horizontal notches.
Fracture toughness
Fracture toughness, measured by the stress intensity factor at the point of fracture, is a key indicator of a rock’s fracture resistance to grow40. In other words, fracture toughness KIIC corresponds to the stress intensity factor KII (Eq. (1)) for P = Pcr, where Pcr is the peak of the load–displacement curve (Fig. 8). Thus, the numerical code developed for this study was used to calculate the fracture toughness of the SCC samples by identifying P = Pcr, and the results are presented as a function of the temperature and lateral pressure in Fig. 9a. This figure illustrates how temperature and lateral pressure increases the fracture toughness. As will be demonstrated later, the drying of clay minerals after thermal treatment enhances the mechanical properties of rocks rich in clay. Additionally, the lateral pressure σH acting perpendicular to the shear fracture increases the shear strength between the newly fractured surfaces, causing the KIIC to increase with the increase of σH.
To demonstrate the impact of temperature and lateral pressure separately on the fracture toughness, two parameters are introduced in this study; Lateral Pressure Increasing Factor (LPIF) and Temperature Increasing factor (TIF). The LPIF which is the KIIC under σH normalized by KIIC under a uniaxial stress state is shown in Fig. 9b, and the TIF which is the KIIC after thermal treatment normalized by KIIC at room temperature is shown in Fig. 9c. Figure 9b illustrates that as σH increases, the LPIF also increases and that as the temperature of thermal treatment increases from RT to 250 and 500 °C, the impact of lateral pressure on fracture toughness decreases. Therefore, it can be inferred that mudstone is more affected by lateral pressure at normal temperatures than at elevated temperatures. The effect of thermal treatment on KIIC is shown in Fig. 9c, it can be observed that under a uniaxial stress state (σH = 0.0 MPa), the KIIC is affected by thermal treatment more than that under a confined stress state (σH = 0.5, 2 and 4 MPa). Comparing LPIF in Fig. 9b and TIF in Fig. 9c, it can be deduced that the mudstone is more affected by lateral pressure than temperature. The LPIF varies between 1.0 and 2.2, while TIF changes between 1.0 and 1.5.
Peak shear strength behavior
In this study, the shear strength behavior of an intact bridge in mudstone was investigated using SCC samples under the effect of temperature and lateral pressure. A schematic diagram of the SCC sample containing a rock bridge tested sample, and shear surfaces is shown in Fig. 10a. As shown in the figure, the intact rock bridge is subjected to normal stress σn = σH and shear stress τ = P/(C × D). At the moment of fracture, the peak shear strength can be calculated by τp = Pcr/(C × D). The peak shear strength τp versus normal stress σn under RT, 250 and 500 °C is shown in Fig. 10b–d respectively. It can be noted that the peak shear strength behavior of a continuous bridge in mudstone (τp = σn tan φp + Cp) follows the bilinear Mohr–Coulomb failure criterion between shear stress τ and normal stress σn of intact materials (τ = σn tan φ + C). The first linear equation is for σn between 0.0 and 0.5 MPa, while the second one is for σn between 0.5 and 4 MPa. An important point should be distinguished between the peak shear strength behavior shown in this study and the Mohr–Coulomb relationship. According to the Coulomb behavior in a jointed rock mass, the increment ratio of shear stress to normal stress Δτ/Δσn represents the friction coefficient f = tan φ between joint surfaces. This coefficient usually ranges from zero (f = 0.0, φ = 0.0°) for perfectly smooth joints to one (f = 1.0, φ = 45°) for completely rough joints. Our results indicated that the increment ratio of peak shear strength to normal stress Δτp/Δσn for σn > 0.5 MPa changes between (fp = 2.43, φp = 67.7°) for T = RT and (fp = 2.9, φp = 71.0°) for T = 500 °C. The friction coefficient (f) or internal friction angle (φ) of continuous rock joints is determined by the slipping between two separated joint surfaces, while in intact rock, the peak friction angle φp is a result of shearing intact material and can be greater than 45°, as in this study. Yang and Kulatilake41 showed that the peak friction angle φp of granite samples changes from 56.5° for joint persistency K = 0.75 to 66.7° for K = 0.25 ( K is the ratio of joint length to the bridge length). Krsmanović and Langof42 and Krsmanovic and Popovic43 reported a high peak friction angle between 70° and 80° according to the test results of the limestone. Moreover, Barton44 showed in table II in his study peak shear friction angle between 66° and 80° measured on joints during tests at low normal stress.
In this study, it can be observed that increasing the temperature from room temperature (RT) to 250 and 500 °C increases the cohesion Cp of intact mudstone under zero normal stress (σn = 0.0 MPa) from 13.2 to 15.9 and 19.5 MPa, respectively. The peak friction angle (φp) for σn > 0.5 MPa also increases from 67.7° to 69.2° and 71.0°, respectively. Thus, thermal treatment at higher temperatures improves the mechanical shear properties (such as φp and Cp) by 2.2% and 20.5% at 250 °C and by 4.9% and 47.7% at 500 °C. Additionally, when increasing the normal stress σn from 0.5 to 4 MPa, the peak shear strength τp increases by 42.4% at T = RT, 42.7% at 250 oC, and 44.6% at 500 °C.
Numerical and experimental comparison
A comparison between numerical stress fields predicted in SCC samples and experimental observation for the developed fracture between the tips of the two horizontal notches is shown in Fig. 11. To compare the experimental work and the numerical model, the experimental fracture is superimposed onto the numerical model as shown in Fig. 11a, note that the resulting fracture is a vertical one between the tips of the two notches, which agrees to a large extent with the shear stress develpoed in the numerical model. Moreover, the formed fracture is not inclined such as the maximum principal stress bridge shown in Fig. 11b. Therefore, the resulting rupture surface is a shear fracture. In addition, the resulting fracture was examined for all SCC samples after the test under four lateral pressures and three temperatures by comparing it with numerical stress fileds and it was observed that all induced fractures are shear fractures. Hence the importance of numerical modeling for evaluating induced fractures in rocks. Induced shear fractures in SCC samples at temperatures of RT, 250 and 500 °C are shown in Fig. 11c, Fig. 11d, and Fig. 11e, respectively. Comparing shear fractures induced under the uniaxial case (σH = 0.0 MPa) and those induced under σH = 4.0 MPa at three temperatures, it can be seen that the latter are straighter and more healed. This observation agrees also with the numerical result that shows the effect of lateral pressure on induced fracture, it was previously concluded that by increasing the lateral pressure, the impact of tensile stress is reduced and the growth of shear fractures is promoted (See Fig. 7).
Explanation of the observed results
This study suggests that thermal treatment improves the mechanical behavior of shear fractures in SCC specimens. The main mechanical properties that were evaluated are the stress intensity factor at the notch tip KIIC, peak shear strength τp, peak friction angle φp, and cohesion Cp. All of these parameters show an improvement with an increase in temperature from RT to 500 °C. As illustrated in Fig. 12, the highest temperature examined for the effect of thermal treatment on the shear properties of SCC samples is 500 °C. This is because at this temperature no thermal cracks were detected on the samples’ surface. It is worth noting that thermal cracks were observed after thermal treatment at a temperature of 600 °C or greater. To explain the observed shear behavior of the mudstone used in this study, a summary of experimental results for the effect of thermal treatment on the shear behaviour of intact rocks is shown in Table 2. Most research in this table focused on the shear behavior of intact granite and showed different regimes for the effect of thermal treatment on shear parameters. Shao et al.7 showed that the φP is slightly affected by temperature increase, it changes between 52° and 55° for a temperature range of RT to 300 °C, while the cohesion CP shows two regimes, increasing by about 23% for T between RT and 100 °C, and then decreasing by about 15% for T from 100 to 300 °C. Zhai et al.8 indicated two obvious regimes for temperature effect on shear strength of healed joints and intact granite, the τP under normal stress ranging from 1 to 9 MPa improved with temperature increase from 25 to 400 °C, and then it decreased for T between 400 and 750 °C. Chen et al.6 and Zhu et al.9 observed only one negative trend for the effect of thermal treatment on the shear strength properties of Weihai granite and Nanan granite, respectively.
In addition to the works conducted on intact granite, Table 2 shows two works on the effect of thermal treatment on the shear behavior of sedimentary rocks such as sandstone. These results are consistent in terms of the effect of temperature on the peak shear strength. Liu et al.10 observed two regimes for T–τP relationship in Neijiang red sandstone, the τP increased for T from 25 to 600 °C, and then decreased for T > 600 °C. In addition, Yin et al.11 pointed out that the τP of Rizhao yellow sandstone has a threshold at T = 400 °C and then dramatically decreased after 400 °C. Regarding our results presented previously in Fig. 10, τP and CP show only one positive trend with temperature increase, while φP is inversely correlated to the temperature under normal pressure < 0.5 MPa, and positively correlated to the temperature under normal pressure > 0.5.
The temperature-dependent shear behavior of different rock types is controlled by two main mechanisms, physical and chemical mechanisms45,46. The physical mechanism includes the growth of thermal fractures due to the difference in the thermal expansion coefficient of constituent minerals and the evaporation of absorbed water. Thermal expansion of constituent minerals can play a positive or negative role depending on the thermal treatment temperature. For rocks that showed two regimes for the effect of temperature on peak shear strength, increasing shear strength until reaching a threshold at a certain temperature (TTh) and then a gradual or rapid decrease. Before TTh, positive regime, the thermal expansion of different minerals can cause the reduction of pore volumes and the distance between the interfaces of individual minerals, which increases the contact, bond strength, and mutual attraction between them47, which eventually leads to an increase in peak shear strength of intact material. With increasing temperature after the TTh, fracture occurs between constituent minerals that show different thermal conductivities and thermo-elastic moduli, resulting in a decrease in peak shear strength48,49. For rocks that showed one regime for the effect of temperature on peak shear strength such as in Nana granite, Zhu et al.9 explained the observed results using optical microscopy that intergranular microcracks were observed after thermal treatment at 200 °C, and transgranular macrocracks began to appear at 300 °C, and by increasing the temperature, additional thermal microcracks were observed in the rock samples.
The chemical mechanism that controls the temperature-dependent shear behavior indicates the removal of water from rock structure and transformation in crystal type, such as the reaction between biotite and oxygen at above 400 °C50, and α to β quartz transition at 573 °C that causes a linear expansion of 0.45% of the quartz51. For the mudstone used in this study, the enhancement of mechanical properties as the temperature increases is a result of its high clay mineral content (92.75%) which has a high affinity to water. Towhata et al.52 investigated the volume change of clays induced by heating and showed that when the temperature rises, material particles become closer together and the contact between them increases, due to the reduction in thickness of the diffuse double layer, which leads to an improvement in the mechanical properties of clay (a physical mechanism). Trindade et al.53 demonstrated that as a result of the gradual loss of water during thermal treatment, clay minerals undergo a series of changes such as dehydration, dehydroxylation, decomposition and formation of new phases, and vitrification (a chemical mechanism). The majority of water loss occurs during the first and second processes, specifically, the dehydration and dehydroxylation processes. The dehydration process occurs at temperatures between 100 and 200 °C. During this process, only the adsorbed, pore, and interlayer water are removed without any changes in the crystal structure of the clay minerals, thus it does not cause thermal crack growth. Therefore, the improvement in mechanical properties of the mudstone in this study at temperatures of 250 and 500 °C is caused by dehydration process. On the other hand, in the dehydroxylation process that occurs at temperatures between 500 and 1000 °C, hydroxyl ions leave the crystal structure of the clay minerals leading to the growth of thermal cracks which can be seen in Fig. 12 after thermal treatment at temperatures of 600 and 700 °C. Zhang et al.1 concluded that the overall structure of the mudstone undergoes phase change at a temperature of about 600 °C, therefore, the mechanical properties of mudstone suddenly change after thermal treatment under this temperature. After this temperature, a chemical reaction of structure occurs, some illite is produced and kaolinite disappears, and finally, the bearing capacity of the mudstone decreases. For temperatures less than 400 °C, no micro-cracks were developed and most pre-existing cracks are intergranular cracks with good closure due to thermal expansion. Micro-cracks were dramatically developed at a temperature between 600 and 800 °C, abundant transgranular, intergranular and intragranular cracks forming a connected network of fractures were observed under 800 °C. In addition, Trindade et al.53 concluded the following mineralogical transformation in calcite and dolomite rich clay at temperature between 300 and 1100 °C, K-feldspar and gothics disappeared at 300 °C, kaolinite disappeared at 500 °C and hematite appeared at 500 °C in calcite and 800 °C in dolomite. During dihydroxylation process at T between 500 and 1000 °C, plagioclase, anatase and illite, disappeared at 700, 800 and 900 to 1000 °C, respectively. While quartz disappeared at temperature > 1100 °C.
Recommendation for future works
This research was conducted after thermal treatment at a temperature range between RT and 500 °C, which is less than the temperature limit of the dihydroxylation process, and under low lateral pressures (0.0 to 4.0 MPa). For future works, we recommend investigating the shear behaviour of intact mudstone during the dehydration and dihydroxylation processes and under high values of lateral pressure. In addition, we recommend using a scanning electron microscope (SEM) and X-ray diffraction (XRD) to investigate the development of thermal microcracks and mineralogical transformations in clay minerals after thermal treatment.
Conclusions
This study conducted a comprehensive analysis of the impact of thermal treatment and lateral pressure on the shear strength characteristics of intact mudstone by using a Short Core in compression test (SCC). Two methods were adopted to achieve the goal of the current research, numerical and experimental methods. In the numerical method, a numerical code was developed based on the displacement discontinuity method to simulate the SCC test. Shear and maximum stress fields were obtained over the entire SCC samples and compared with experimental observations after the test. The study revealed that when samples were subjected to uniaxial and lateral stress states at various temperatures (RT, 250 °C, and 500 °C), the fractures observed in SCC samples were shear fractures. This was concluded based on their alignment with the vertical shear stress bridge that connects the inner tips of the two horizontal notches, as opposed to being inclined as per the maximum principal stress bridge. By increasing lateral pressure, the impact of tensile stress is reduced and the growth of shear fractures is promoted, and the resulting shear fractures become straighter and more healed.
The experimental work in this study concluded that in comparison with other rock types such as granite and sandstone shown in the literature, shear properties of intact mudstone that include mode II fracture toughness (KIIC), peak shear strength (τP), peak friction angle (φP) and the cohesion (CP) have only one positive trend with temperature increase up to 500 °C. This is because, until 500 °C, no thermal fractures were developed in the mudstone, the contact between particles increased due to thermal expansion, and clay minerals were dried during the dehydration process that can occur at a temperature between 100 and 200 °C. It is worth mentioning that some thermal fractures were observed after thermal treatment at 600 °C, and a network of these fractures was observed at 700 °C. In addition, the experimental method concluded that the peak fraction angle is less affected by thermal treatment than the cohesion, by increasing T from RT to 500 °C, φP improved by about 4.9%, while the CP improved by about 47.7%. The bilinear Mohr–Coulomb failure criterion can be used to model the peak shear strength behaviour of intact mudstone before and after thermal treatment.
Data availability
The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.
References
Zhang, L., Mao, X., Liu, R., Li, Y. & Yin, H. Meso-structure and fracture mechanism of mudstone at high temperature. Int. J. Min. Sci. Technol. 24, 433–439. https://doi.org/10.1016/j.ijmst.2014.05.003 (2014).
Xu, L., Gong, F. & Liu, Z. Experiments on rockburst proneness of pre-heated granite at different temperatures: Insights from energy storage, dissipation and surplus. J. Rock Mech. Geotech. Eng. 14, 1343–1355. https://doi.org/10.1016/j.jrmge.2021.08.004 (2022).
Wong, L. N. Y., Cui, X., Zhang, Y., Wu, Z. & Guo, T. Experimental investigation of thermal strengthening in Sichuan marble. Rock Mech. Rock Eng. https://doi.org/10.1007/s00603-022-02995-5 (2022).
Rimi, A. et al. Towards a de-carbonized energy system in north-eastern Morocco: Prospective geothermal resource. Renew. Sustain. Energy Rev. 16, 2207–2216. https://doi.org/10.1016/j.rser.2011.12.008 (2012).
Prassetyo, S. H., Gutierrez, M. & Barton, N. Nonlinear shear behavior of rock joints using a linearized implementation of the Barton-Bandis model. J. Rock Mech. Geotech. Eng. 9, 671–682. https://doi.org/10.1016/j.jrmge.2017.01.006 (2017).
Chen, B., Shen, B. & Jiang, H. Shear behavior of intact granite under thermo-mechanical coupling and three-dimensional morphology of shear-formed fractures. J. Rock Mech. Geotech. Eng. https://doi.org/10.1016/j.jrmge.2022.04.006 (2022).
Shao, S., Ranjith, P., Wasantha, P. & Chen, B. Experimental and numerical studies on the mechanical behaviour of Australian Strathbogie granite at high temperatures: an application to geothermal energy. Geothermics 54, 96–108. https://doi.org/10.1016/j.geothermics.2014.11.005 (2015).
Zhai, T., Zhu, J., Zhou, C. & Yang, T. Experimental investigation of the effect of thermal treatment on shear characteristics of healed rock joints. Int. J. Rock Mech. Min. 152, 105074. https://doi.org/10.1016/j.ijrmms.2022.105074 (2022).
Zhu, Z. et al. Experimental investigation on mechanical behaviors of Nanan granite after thermal treatment under conventional triaxial compression. Environ. Earth Sci. 80, 1–14. https://doi.org/10.1007/s12665-020-09326-3 (2021).
Liu, K. et al. Effects of thermal treatment on the shear behavior and characteristics of intact sandstone: Laboratory experiment of variable-angle shear. Bull. Eng. Geol. Environ. 81, 471. https://doi.org/10.1007/s10064-022-02973-9 (2022).
Yin, Q. et al. Shear mechanical responses of sandstone exposed to high temperature under constant normal stiffness boundary conditions. Geomech. Geophys. Geo-Energy Geo-Resour. 7, 1–17. https://doi.org/10.1007/s40948-021-00234-9 (2021).
Feng, Z., Zhang, C., Dong, F. & Yang, D. Elastic modulus evolution of triaxially stressed mudstone at high temperature up to 400 °C. Energy Sci. Eng. 8, 4126–4135. https://doi.org/10.1002/ese3.801 (2020).
Li, T. & Yang, X. Reliability analysis of tunnel face in broken soft rocks using improved response surface method. Int. J. Geomech. 18, 04018021. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001129 (2018).
Nocilla, N., Evangelista, A. & Scotto di Santolo, A. Fragmentation during rock falls: Two Italian case studies of hard and soft rocks. Rock Mech. Rock Eng. 42, 815–833. https://doi.org/10.1007/s00603-008-0006-0 (2009).
Chen, J., Yin, L., Ren, S., Lin, L. & Fang, J. The thermal damage properties of mudstone, gypsum and rock salt from Yingcheng, Hubei, China. Minerals 5, 104–116. https://doi.org/10.3390/min5010104 (2015).
Liu, R., Mao, X., Zhang, L. & Ma, D. Thermal properties of mudstone at high temperature. Int. J. Geomech. 14, 04014023. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000308 (2014).
Lu, Y., Wang, L., Sun, X. & Wang, J. Experimental study of the influence of water and temperature on the mechanical behavior of mudstone and sandstone. Bull. Eng. Geol. Environ. 76, 645–660. https://doi.org/10.1007/s10064-016-0851-0 (2017).
Alneasan, M., Alzo’ubi, A. K., Behnia, M. & Mughieda, O. Experimental observations on the effect of thermal treatment on the crack speed and mode I and II fracture toughness in brittle and ductile rocks. Theor. Appl. Fract. Mech. https://doi.org/10.1016/j.tafmec.2022.103525 (2022).
Alzo’ubi, A. K. & Alneasan, M. Experimental study on the effect of thermal treatment on the mechanical properties of clay-rich rocks (mudstone). Results Eng. https://doi.org/10.1016/j.rineng.2022.100728 (2022).
Alneasan, M. & Alzo’ubi, A. K. Comprehensive investigation of rock fracture behaviour in clay-rich rocks under the effect of temperature: Experimental study under three loading modes (I, I/II, II). Eng. Fract. Mech. 276, 108933. https://doi.org/10.1016/j.engfracmech.2022.108933 (2022).
Yu, M. et al. Creep behavior of carbonaceous mudstone under triaxial hydraulic coupling condition and constitutive modelling. Int. J. Rock Mech. Min. 164, 105357. https://doi.org/10.1016/j.ijrmms.2023.105357 (2023).
Zhang, L. et al. Brittle–ductile transition of mudstone in coal measure rock strata under high temperature. Int. J. Geomech. 20, 04019149. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001549 (2020).
Mao, R., Mao, X., Zhang, L. & Liu, R. Effect of loading rates on the characteristics of thermal damage for mudstone under different temperatures. Int. J. Min. Sci. Technol. 25, 797–801. https://doi.org/10.1016/j.ijmst.2015.07.015 (2015).
Luo, J. & Wang, L. High-temperature mechanical properties of mudstone in the process of underground coal gasification. Rock Mech. Rock Eng. 44, 749–754. https://doi.org/10.1007/s00603-011-0168-z (2011).
Zhang, L., Mao, X., Liu, R., Guo, X. & Ma, D. The mechanical properties of mudstone at high temperatures: An experimental study. Rock Mech. Rock Eng. 47, 1479–1484. https://doi.org/10.1007/s00603-013-0435-2 (2014).
Watkins, J. & Liu, K. A finite element study of the short beam test specimen under mode II loading. Int. J. Cem. Compos. Lightweight Concr. 7, 39–47. https://doi.org/10.1016/0262-5075(85)90025-9 (1985).
Jung, Y., Park, E. & Kim, H. In ISRM International Symposium - EUROCK 2016.
Crouch, S. L. & Starfield, A. M. Boundary Element Methods in Solid Mechanics: With Applications in Rock Mechanics and Geological Engineering (Allen & Unwin, 1983).
Alneasan, M. & Alzo’ubi, A. K. Temperature effect on the fracture behavior of granite under three loading modes (I, I/II, and II). Rock Mech. Rock Eng. https://doi.org/10.1007/s00603-022-03149-3 (2022).
Xu, Y., Yao, W., Zhao, G. & Xia, K. Evaluation of the short core in compression (SCC) method for measuring mode II fracture toughness of rocks. Eng. Fract. Mech. 224, 106747. https://doi.org/10.1016/j.engfracmech.2019.106747 (2020).
Yao, W., Xu, Y., Wang, C., Xia, K. & Hokka, M. Dynamic mode II fracture behavior of rocks under hydrostatic pressure using the short core in compression (SCC) method. Int. J. Min. Sci. Technol. 31, 927–937. https://doi.org/10.1016/j.ijmst.2021.08.001 (2021).
Horii, H. & Nemat-Nasser, S. Compression-induced microcrack growth in brittle solids: Axial splitting and shear failure. J. Geophys. Res. Solid 90, 3105–3125. https://doi.org/10.1029/JB090iB04p03105 (1985).
Nemat-Nasser, S. & Horii, H. Compression-induced nonplanar crack extension with application to splitting, exfoliation, and rockburst. J. Geophys. Res. Solid 87, 6805–6821. https://doi.org/10.1029/JB087iB08p06805 (1982).
Zhang, C. et al. Dynamic shear fracture behavior of rocks: Insights from three-dimensional digital image correlation technique. Eng. Fract. Mech. 277, 109010. https://doi.org/10.1016/j.engfracmech.2022.109010 (2023).
Horii, H. & Nemat-Nasser, S. Brittle failure in compression: Splitting faulting and brittle-ductile transition. Phil. Trans. R. Soc. Lond. Ser. A Math. Phys. Sci. 319, 337–374. https://doi.org/10.1098/rsta.1986.0101 (1986).
Atkinson, B. K. Introduction to fracture mechanics and its geophysical applications. In Fracture Mechanics of Rock (ed. Atkinson, B. K.) 1–26 (Academic press, 1987).
Shou, K. J. & Crouch, S. L. A higher order displacement discontinuity method for analysis of crack problems. Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 32, 49–55. https://doi.org/10.1016/0148-9062(94)00016-V (1995).
Ulusay, R. & Hudson, J. A. The Complete ISRM Suggested Methods for Rock Characterization, Testing and Monitoring: 1974–2006 (International Society for Rock Mechanics Commission on Testing Methods, 2007).
Su, X. et al. Effect of mesoscopic structure on hydro-mechanical properties of fractures. Environ. Earth Sci. 79, 1–23. https://doi.org/10.1007/s12665-020-8871-2 (2020).
Whittaker, B. N., Singh, R. N. & Sun, G. Rock Fracture Mechanics: Principles, Design, and Applications (Elsevier, 1992).
Yang, X.-X. & Kulatilake, P. H. Laboratory investigation of mechanical behavior of granite samples containing discontinuous joints through direct shear tests. Arab. J. Geosci. 12, 1–10. https://doi.org/10.1007/s12517-019-4278-3 (2019).
Krsmanović, D. & Langof, Z. Grundfragen auf dem Gebiete der Geomechanik/Principles in the Field of Geomechanics 20–30 (Springer, 1964).
Krsmanovic, D. & Popovic, M. In 1st ISRM Congress.
Barton, N. Review of a new shear-strength criterion for rock joints. Eng. Geol. 7, 287–332. https://doi.org/10.1016/0013-7952(73)90013-6 (1973).
Tang, Z. C., Sun, M. & Peng, J. Influence of high temperature duration on physical, thermal and mechanical properties of a fine-grained marble. Appl. Therm. Eng. 156, 34–50. https://doi.org/10.1016/j.applthermaleng.2019.04.039 (2019).
Zhao, Z., Dou, Z., Xu, H. & Liu, Z. Shear behavior of Beishan granite fractures after thermal treatment. Eng. Fract. Mech. 213, 223–240. https://doi.org/10.1016/j.engfracmech.2019.04.012 (2019).
Dmitriyev, A. Physical Properties of Rocks at High Temperatures Vol. 684 (National Aeronautics and Space Administration, 1972).
Kranz, R. L. Microcracks in rocks: A review. Tectonophysics 100, 449–480. https://doi.org/10.1016/0040-1951(83)90198-1 (1983).
Kranz, R. L. Microcracks in rocks: A review. Tectonophysics 100, 449–480. https://doi.org/10.1016/0040-1951(83)90198-1 (1983).
Pavese, A. et al. P-V and T-V equations of state of natural biotite: An in-situ high-pressure and high-temperature powder diffraction study, combined with Mössbauer spectroscopy. Am. Miner. 92, 1158–1164. https://doi.org/10.2138/am.2007.2359 (2007).
Somerton, W. H. Thermal Properties and Temperature-Related Behavior of Rock/Fluid Systems (Elsevier, 1992).
Towhata, I., Kuntiwattanaku, P., Seko, I. & Ohishi, K. Volume change of clays induced by heating as observed in consolidation tests. Soils Found. 33, 170–183. https://doi.org/10.3208/sandf1972.33.4_170 (1993).
Trindade, M. J., Dias, M., Coroado, J. & Rocha, F. Mineralogical transformations of calcareous rich clays with firing: A comparative study between calcite and dolomite rich clays from Algarve, Portugal. Appl. Clay Sci. 42, 345–355. https://doi.org/10.1016/j.clay.2008.02.008 (2009).
Acknowledgements
We would like to thank the ORSP at Abu Dhabi University for funding this project (19300604). We also would like to extend our thanks to Azmoneh Foulad Consulting Engineers (https://en.azmouneh.com/) for permission to use facilities in his company’s rock mechanics lab under the supervision of Eng. Mohsen Aghababaei (m.aghababaei@mi.iut.ac.ir) and Eng. Behzad Nateghpour (b.nateghpour@mi.iut.ac.ir).
Author information
Authors and Affiliations
Contributions
M.A. was responsible for numerical simulation, conducting experimental tests, conception and design of the study, acquisition of data, analysis and/or interpretation of data, and drafting the manuscript. A.K.A. was responsible for the conception and design of the study, acquisition of data, analysis and/or interpretation of data and drafting the manuscript, and revising the manuscript critically for important intellectual content.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Alneasan, M., Alzo’ubi, A.K. Extensive experimental investigation on the effect of thermal treatment and lateral pressure on the shear behavior of intact mudstone. Sci Rep 13, 6820 (2023). https://doi.org/10.1038/s41598-023-33841-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-33841-5
- Springer Nature Limited