Abstract
Providing sufficient energy supply and reducing the effects of global warming are serious challenges in the present decades. In recent years, biodiesel has been viewed as an alternative to exhaustible fossil fuels and can potentially reduce global warming. Here we report for the first time the production of biodiesel from oleic acid (OA) as a test substrate using porous sulfonic acid functionalized banana peel waste as a heterogeneous catalyst under microwave irradiation. The morphology and chemical composition of the catalyst was investigated using Powder X-ray diffraction (PXRD) analysis, Fourier transform infrared (FTIR) spectroscopy, Thermogravimetric analysis (TGA), Transmission electron microscopy (TEM), and Scanning electron microscopy- Energy dispersive X-ray spectroscopy (SEM–EDX). The SEM–EDX analysis of the catalyst revealed the presence of sulfur in 4.62 wt% amounting to 1.4437 mmol g−1 sulfonic acids, which is accorded to the high acidity of the reported catalyst. Using response surface methodology (RSM), through a central composite design (CCD) approach, 97.9 ± 0.7% biodiesel yield was observed under the optimized reaction conditions (methanol to OA molar ratio of 20:1, the temperature of 80 °C, catalyst loading of 8 wt% for 55 min). The catalyst showed excellent stability on repeated reuse and can be recycled at least 5 times without much activity loss.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
The demand for burning fossil fuels is growing day by day as a result of fast urbanization and population growth. These fuels will run out in time at the current consumption rate1. Researchers have been looking for ways to replace fossil fuels with renewable and environmentally benign energy sources due to the chronic need for energy and the inevitable depletion of crude oil reserves worldwide2,3. In addition, fossil fuel consumption results in severe environmental pollution by elevated atmospheric CO2 concentrations, thereby increasing global warming4,5. As a result, it is imperative to meet rising energy demands while simultaneously reducing CO2 emissions to prevent catastrophic global warming amicably and sustainably using renewable resources. Although few alternative energy resources can resolve future energy needs by reducing greenhouse gas emissions, because of the existing infrastructure, biodiesel, which is made up of long-chain fatty acid methyl esters (FAMEs)6,7, appears to be the most viable, readily implemented alternative to conventional diesel fuel8,9,10. Besides being sustainable, renewable11, nontoxic, biodegradable12, carbon–neutral, and safe to handle, biodiesel produces low emissions throughout its life cycle as an esterification product of vegetable oil and methanol6,13,14. As an additional benefit, normal diesel engines can operate on biodiesel without modifications15. Biodiesel can be made from various feedstocks such as soybean, canola, palm, and rapeseed oils16,17,18,19. The cost of edible oil-based raw materials for biodiesel synthesis accounts for 70–80% of the total cost, making biodiesel production more expensive than diesel20.
Several works are being done to reduce the cost of these raw materials. Lathiya et al.21 reported a sulfonated carbon catalyst from waste orange peel through carbonization followed by sulfonation treatment, Khan et al.22 targeted agro waste derived metal oxide, and Zhao et al.23 used pomelo peel biochar for biodiesel synthesis. Non-edible sources such as waste cooking oil (WCO) and Jatropha curcas have been identified as good substitutes24. They tend to contain higher free fatty acid (FFA) levels, which makes them less suitable for alkali-catalyzed processes. Substantial FFA present in the feedstock can adversely affect the performance of the alkaline catalyst, as they react with the catalyst, causing soap and water formation through the saponification process25. Moreover, this type of reaction complicates downstream product separation, which results in an extended production process that is more expensive to operate.
Hence, choosing a proper catalyst is especially important. Generally, acid-catalyzed esterification of FFAs is preferred since the catalyst is designed to tolerate high FFA levels in the feedstock. Sulfuric acid (H2SO4) is the most commonly used conventional catalyst. According to the study done by Aranda et al.26, H2SO4 exhibited higher esterification activity in palm fatty acids. The H2SO4 has a higher catalytic activity due to its ability to protonate the carboxylic moiety of fatty acids and create tetrahedral intermediates. It is more economical and practical to catalyze biodiesel production with heterogeneous than homogeneous catalysts27 because of its many advantages, including ease of regeneration, time-saving, reduced corrosiveness, safety, and cost. Mateo et al.28 reported a sulfonated carbon catalyst developed from agricultural wastes via a one-step process involving direct carbonization and sulfonation with H2SO4 as a reagent. Mendaros et al.29 also synthesized a solid carbon acid catalyst by direct sulfonation of cacao shell for the esterification of oleic acid. Shang et al.30 used agricultural byproduct peanut shell, Kumawat, and Rokhum31 used orange peel waste for simultaneous carbonization and sulfonation with H2SO4 as a reagent. Hassan et al.32 revealed that using H2SO4 for sulfonation is of low cost and provides high acidity to the carbonaceous Bentonite catalyst. Ngaosuwan et al.33 predicted that these sulfonated-carbon catalysts in industries for catalytic reactions like esterification, transesterification, nitration, and cellulose hydrolysis could soon replace homogeneous H2SO4 catalyst.
Response surface methodology (RSM) is used to evaluate the impact of two or more independent factors on a complicated set of dependent variables. It uses numerous regression and correlation analyses to reduce the number of experiments required to gather adequate data for a statistically valid result. Central composite design (CCD) is one of the most popular RSM response design experiments. This method has already been utilized to improve biodiesel yield from a wide range of feedstocks and catalysts27. Doehlert Design (DD), Box-Behnken Design (BBD), and full factorial design are the types of design used for the RSM study, including CCD34. However, because of the benefit of optimizing multifactor problems with the minimum number of experimental runs, CCD is extensively employed for optimization procedures. The CCD model permits two-level factors to be extended, which are commonly utilized in response surface modeling and optimization. The most significant benefit of this kind of optimization model is its accuracy, as the three-level factorial experiment is not required to construct a second-order quadratic model34,35. The effects of various factors such as methanol to the oleic acid molar ratio (MOMR), catalyst weight percentage, temperature, and time were investigated systematically.
According to the report of Statista 2021, The largest fruit market in the entire globe is the banana market. The production of bananas was 124.98 million metric tonnes in 202136. In addition, as a waste, it is quite expensive to dispose of away banana peel. Hence its beneficial usage would boost the economy of bananas in general37. Although a carbon-based solid catalyst made from waste biomass has the potential to solve many issues related to biodiesel production, its use on an industrial scale is constrained by the expense associated with catalyst fabrication38. For the industrial production of biodiesel, it is therefore highly desired to use a straightforward, economic, and ecologically friendly strategy that uses a waste biogenic heterogeneous catalyst39. Carbon materials such as banana peels are generally inexpensive and easily available, and they can be readily functionalized with –SO3H groups by treating them with concentrated H2SO4, resulting in sulfonated carbon catalysts. The acid-catalyzed esterification of oleic acid, normally present in natural oil, has become a paradigm in biodiesel research. Thus, the current study examines a novel method of using sulfonic acid functionalized banana peel (denoted as BP-SO3H-10-16-80 as a heterogeneous catalyst, as shown in Fig. 1), which can be regarded as more economical and effective, to convert oleic acid to biodiesel.
Experimental methodology
Materials and methods
Banana peels (Musa acuminata) were collected from Kolasib, Mizoram (24° 13′ 36.3792″ N, 92° 40′ 39.9″ E), India. The required permissions were obtained for collecting banana peels, and this study complies with relevant institutional, national, and international guidelines and legislation. The collected banana peels were dried thoroughly in the sunlight. Oleic acid (Analytical Reagent Grade, purity ≥ 99%) was purchased from Sigma Aldrich. Methanol (99.8%), H2SO4 (98.07%), BaCl2 (99.95%), NaHCO3 (≥ 98.7%) and were purchased from Merck. Double distilled water was used throughout the experiments. All the solvents and chemicals used were of analytical grade, bought from commercial sources, and utilized without purification.
Preparation of BP-SO3H catalyst
Four batches of banana peel-supported sulfonic acid (BP-SO3H) catalysts were prepared by varying the banana peel-to-sulfuric acid ratio, reaction time, and temperature. Catalysts prepared in the initial batch include dried banana peel powder (1 g) mixed thoroughly with conc. H2SO4. Banana peel powder: H2SO4 ratios (g L−1) of 1:5, 1:10, 1:15, and 1:20 were used, whereas the reaction temperature varied between 80 and 120 °C while reaction time was monitored for 16, 18, 20, 22, and 24 h. In order to remove residual sulfate ions in the filtrate, 50–60 mL of deionized water was added to the mixture. It was washed several times with hot deionized water until no residual sulfate ions could be detected (a 6 mol L−1 solution of BaCl2 was used for testing). The resultant sulfonic acid functionalized banana peel (BP-SO3H) was dried in an oven overnight. All the synthesized BP-SO3H catalysts were assigned a code based on their synthesis procedure; BP-SO3H-X-Y-Z, where X is the wt/volume ratio of banana peel/H2SO4, Y is the 'in 'situ' hydrothermal-sulfonation time, and Z stands for reaction temperature. Accordingly, the catalyst prepared using a 1:10 (wt/volume) banana peel/sulfuric acid ratio, hydrothermal sulfonation time of 16 h, and reaction temperature of 80 °C were designated as BP-SO3H-10-16-80.
Catalyst characterization
Based on the modified Boehm titration procedure, the density of –COOH, –SO3H, and –OH groups on the surface of BP-SO3H was determined40,41. The total acid density was determined using basic solutions of NaOH. The acid density of –COOH and –SO3H were calculated using NaHCO3 and NaCl, respectively. Equation (1) was used to calculate the total surface acid density of the catalyst.
where, \(\frac{{n}_{\text{HCl} }}{{n}_{B}}\) is the molar ratio of HCl to base reacted; \(\left[B\right]\) and \({V}_{B}\) are the concentration and volume of the reaction base mixed with the catalyst, respectively; Valiquot is the volume of the aliquot taken from the \({V}_{B}\), [HCl] and \({V}_\text{HCl}\), are the concentration and volume of acid used in the acidification, and [NaOH] and \({V}_\text{NaOH}\) are the concentration and volume of the NaOH used in the titration.
A 40 kV generator voltage and a tube current of 100 mA were used to obtain powder X-ray diffraction (XRD) patterns at 2θ = 10–60° on an X'Pert Pro diffractometer (PAN analytical, Netherland). Before degassing for 10 h at 150 °C, the Brunauer–Emmett–Teller (BET) analysis was performed on a surface area and porosity analyzer (Micromeritics ASAP 2010, USA). A JEOL JSM-7600F (Japan) microscope was utilized for energy-dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM) at 1500× magnification power, 80 mA beam current, and 20 kV. The catalyst was disseminated in ethanol and dropped onto a Cu grid drop-wise before being dried in an oven. An electron microscope (JEM-2100, 200 kV) from JEOL (Tokyo, Japan) was used to record high-resolution transmission electron microscopy (HRTEM). Thermo gravimetric analysis (TGA) was performed in the temperature range of 50–600 °C under the continuous flow on N2 using a Perkin-Elmer instrument with model no TGA 4000 (Shelton, USA). A Nicolet 6700 spectrophotometer (Nicolet Instrument Corporation, USA) was used to record Fourier transform infrared spectra (FTIR) on the KBr pellet. Thermo Fisher 'Scientific's ESCALAB Xi+ (USA) device with Al Kα radiation was used for the X-ray photoelectron spectroscopy (XPS) analysis.
Esterification of oleic acid
The esterification reaction was carried out under microwave irradiation under different conditions (50–90 °C, 25–65 min, 2–10 catalyst wt% (with respect to OA), 5:1–25:1 MOMR; Fig. 2). Optimized conditions (see “Results and Discussion”) were methanol (20 mmol) and OA (1 mmol) in a 20:1 molar ratio and 8 wt% catalyst (0.0225 g) at 80 °C for 55 min. Thin-layer chromatography (TLC) was used to monitor the progress of the reaction and the formation of fatty acid methyl ester (FAME). The newly synthesized biodiesel was filtered when TLC showed complete conversion. The excess amount of methanol in the compound was evaporated using a rotary evaporator followed by a suction pump. 1HNMR analysis (Fig. S4) and Gas chromatography (GC), Fig. S5, were used to confirm the formation and purity of the biodiesel or fatty acid methyl ester product. The biodiesel quality (Table S1) was studied using the conventional American Society for Testing Materials (ASTM).
Parametric optimization by response surface methodology (RSM)
Central composite design (CCD) efficiently fits experimental data using a second-order model. In this manner, variables are structured at three levels, each uniformly spaced, i.e., Low, intermediate, and high values represented by − 1, 0, and + 1, respectively42. It is more successfully utilized to construct a model that can be tested for accuracy using statistical analysis of variance (ANOVA) is a software-guided technique. This work uses CCD to measure model accuracy and how interacting factors affect the results43. The MeOH: OA molar ratio (A), catalyst loading (B), time (C), and temperature (D) were all investigated in the biodiesel manufacturing process. In total, 30 experiments were designed. To determine the performance of the components and their interaction affects the efficiency (optimal response) of biodiesel production, a quadratic polynomial equation (Eq. 2) is applied.
where αo is the intercept term, α1–4 are the coefficients of the linear terms, α12-14, α23, α24, and α34 are coefficients of the interaction terms, and α11, α22, α33, and α44 are coefficients of the quadratic terms. A–D are coded factors.
Biodiesel product analysis
The biodiesel or fatty acid methyl ester was purified using column chromatography and then analyzed by 1H NMR and 13C NMR for product confirmation and purity. On a Bruker Avance II 700 MHz spectrometer (Fällanden, Switzerland), the 1H NMR and 13C NMR spectra of the produced biodiesel were recorded using tetramethylsilane (TMS) as an internal reference. Using the integrals for methoxy and methylene groups (\({\mathrm{A}}_{\mathrm{Me}}\) and \({\mathrm{A}}_{{\mathrm{CH}}_{2}}\), respectively in Eq. (3)), biodiesel conversion was determined by the equation derived by Knothe and Kenar.
where C indicates the triglyceride to biodiesel (fatty acid methyl ester) conversion percentage (%), AMe denotes the integration value of the methyl esters, and \({A}_{{CH}_{2}}\) is the integration value of the methylene protons. Factors 2 and 3 ascribe to the proton number in methylene and the proton number in the methyl ester, respectively. The biodiesel yield was calculated by the equation given by Leung and Guo as given in Eq. (4).
Kinetic study of the reaction
Considering the reaction to be a Pseudo-Homogeneous (P–H) model, the rate of the reaction can be expressed as
where \(k\) and \({k}^{^{\prime}}\) are the reaction rate constants, CA, CB, CE and Cw are the concentration of oleic acid, methanol, methyl ester and water respectively; a, b, e, and w are the respective reaction orders. Since the concentration of methanol is too high with respect to other concentration terms, thus \({C}_{B}^{b}\) is considered to be constant. Also, \(k\) is larger than \({k}^{^{\prime}}\)44,45, so Eq. (5) can be reduced to (Eq. 6).
\({C}_{{A}_{o}}\) and \(X\) refers to initial concentration of oleic acid and fractional biodiesel yield, respectively. Furthermore, Eq. (7) can be written as Eq. (8).
where, \(\left(\frac{k}{{C}_{{A}_{o}}}\right)= {k}_{1}\) and for n = 1, the above equation, Eq. (8) can be integrated as Eq. (9). Similarly, for n = 2, second order reaction, Eq. (8) can be integrated to a simplified equation, Eq. (10). As given in Eq. (11), the activation energy (Ea) of the reaction was determined using the Arrhenius equation in which the rate constants at different temperatures were used (50–90 °C)46.
Here, the reaction temperature is denoted by T, the pre-exponential factor by A and R is 8.314 × 10–3 kJ K−1 mol−1.
Test for heterogeneity and reusability of the catalyst
The hot filtration method (Sheldon's test)47 was employed for the heterogeneity test of the BP-SO3H-15-18-100 catalyst. After 35 min, filtration separated the catalyst from the reaction mixture. Then, the reaction was continued for another 30 min with a catalyst-free and filtered reaction mixture; further TLC and GC were employed to monitor the progress of the reaction.
TLC conditions: TLC plates were made from microscope slides of 76.2 × 25.5 mm and a thickness of 1.2 mm. Silica was used as the adsorbent (stationary phase), and 20% ethyl acetate solution (mobile phase) was used to run the TLC plates.
GC conditions: For GC analysis, the sample was diluted five times with ethanol. Conditions for a GC include an HP-5MS quartz capillary (30 mm × 0.25 0.25 mm × 0.25 m), a column temperature range of 70–260 °C, a programmed temperature rate of 5 °C/min, a column flow rate of 1.0 mL/min, an inlet temperature of 260 °C, a pressure in front of the column of 100 kPa, an injection volume of 0.40 L, transmission line temperature of 250 °C, an ion source temperature of 220 °C, a quadrupole temperature of 140 °C, and a mass scanning range of 35–500 amu.
Reusing a solid heterogeneous catalyst is one of its most important characteristics. Oleic acid esterification using recycled catalyst was carried out under optimized conditions to test the catalyst's reusability. The recovered catalyst was filtered and washed with methanol after each catalytic run. It was then dried overnight at 80 °C in a vacuum oven before being utilized in the next cycle.
Results and discussion
Total acidity test using Boehm titration
The catalyst of 100 mg was dissolved in 40 mL of 0.05 M NaOH and stirred for 24 h. The mixture was then filtered, and 10.00 mL of aliquot was taken and acidified with 20.00 mL of standardized 0.05 M HCl solution. Further, phenolphthalein indicator was added and titrated with standardized 0.05 M NaOH. The same procedure was repeated to get the concordant value. The above procedure was followed to determine the acid density of –COOH using NaHCO3 as a basic solution and the acid density of SO3H 2 M NaCl solution. Finally, the acid density of –OH was calculated by subtracting the acid density of –COOH and –SO3H from the total acid density.
Catalyst composition in relation to sulfonation parameters
A total of four batches of BP-SO3H catalysts with banana peel and conc. H2SO4 in the ratio of 1:5, 1:10, 1:15, and 1:20 (wt in g/volume in mL) were prepared with different reaction times ranging from 16 to 24 h by varying temperatures from 80 to 120 °C in a Pyrex bottle to determine the level of sulfonation. In the sulfonation process, the ratios of sulfonating agent to biomass precursor ratio are known to impact the total acid density of the catalyst48. As the sulfuric acid added in the first batch (1:5) was much less, the S content and overall acidity were quite low compared to the later batches. The overall acid density in 1:10, 1:15, and 1:20 were studied separately, and it was found that 1:15 (wt in g/volume in mL) is the optimum condition, while continued addition of sulfuric acid resulted in a drop in both parameters. This can be attributed to several factors. Dehydration, which occurs at high sulfuric acid concentrations, will remove –OH and –COOH groups, thus reducing total acid density49. With the increase in dehydration, aromatization and cyclization proceed more quickly, decreasing the amount of surface that may be available for sulfonation, ultimately reducing S content. The ratio of 1:15 had the highest acid density (4.3 mmol g−1) and sulfur content (4.62 wt%). Hence it was concluded that when sulfuric acid is loaded at a higher concentration during sulfonation, more -SO3H groups can be attached to the catalyst surface.
Increasing the time of sulfonation resulted in an increase in the acid densities of the catalysts until an optimal time of 18 h was reached. However, a further increase in the sulfonation time beyond the optimal point did not influence the overall acid density values of the catalyst50,51.
With the increase in the sulfonation temperature, the –SO3H and phenolic –OH density of the catalyst increases significantly up to a certain temperature. However, BP-SO3H-15-18-120 had lower amounts of –SO3H and phenolic –OH than BP-SO3H-15-18-100 because high sulfonation temperature resulted in a higher degree of acid dehydration, which led to reduced C–H and C–OH bonds that are thereby producing harder carbon materials which provide lesser edges for sulfonation50,52. The preparation and activities of different catalysts used for biodiesel synthesis are presented in Table 1, whereas the complete experimental biodiesel yields using the optimized catalyst (BP-SO3H-15-18-100) are shown in Table 2.
Characterization of catalyst
Powder X-ray diffraction analysis (PXRD) was used to evaluate the crystallinity of the biomass-derived BP-SO3H catalyst, and the results were analysed. According to Fig. S1a given in supplementary information (SI), there is no particular diffraction peak in the whole pattern. A broad peak is obtained around 2θ = 23°, suggesting that amorphous catalysts were produced during a green synthesis process53. It is generally accepted that sulfonated catalysts have amorphous structures consisting mostly of sheets of polycyclic aromatic carbons coated with –SO3H, –OH, and –COOH54.
TGA of BP and BP-SO3H (Fig. S1b) displays significant changes under the thermal responses at a temperature ranging from 30 to 800 °C. In the TGA of BP, a small mass loss from the temperature range 30–100 °C could be ascribed to the loss of moisture, while a major mass loss from 140 to 430 °C could be attributed to the evolution of volatile compounds present in the BP. However, in the TGA of BP-SO3H, mass loss are accounted for the loss of adsorbed water from temperature range of 50–100 °C followed by mass loss from range of 250–500 °C due to the decomposition of –COOH, –SO3H, and –OH groups55.
As shown in Fig. S1c, the N2 adsorption–desorption isotherm of BP-SO3H catalyst exhibited a type IV isotherm with H3-type hysteresis loop, suggesting the presence of non-homogeneous mesoporous material in the catalyst. Pore size distribution analysis by BJH (Barrett, Joyner, and Halenda) showed a distribution of 2.205 nm. The pore volume and surface area of catalyst BP-SO3H were both within the ranges predicted for this type of material, at 0.016 cc g−1 and 14.024 m2 g−1, respectively56.
In order to detect the functional groups present, FTIR analysis of BP-SO3H-15-18-100 along with BP, recovered BP-SO3H was performed (Fig. S1d). The analysis showed that a 1028 cm−1 peak is associated with SO3− symmetric stretching57 found in both the sulfonated and recovered catalyst, indicating the presence of the sulfonic group even after 5-times reuse of catalyst. Peaks at 1700 cm−1 and 1613 cm−1 were attributable to carbonyl stretching and C=C stretching in aromatic rings, respectively58. The peak at 2921 cm−1 and 3300 cm−1 corresponds to C–H and O–H stretching vibrations, respectively59.
In the SEM and TEM images of raw BP Fig. (S2a,be,f), large particles of irregularly compacted layers could be seen. On the surface of the clay particles, there is a wide distribution of dispersed spherical grains, which may be associated with the presence of organic substances. However, in contrast, the surface of the clay particles of BP-SO3H (Fig. S3c,d) appears to be smoother than the particles of BP. This result also corroborated with the TEM images (Fig. S2g,h) of BP-SO3H which shows agglomeration of dense particles leading to a spherical structure. This possibly could be due to sulfonation using H2SO4 which might be the effect of the acid in oxidizing organic matters and dissolving impurities32. The EDX analysis results also support the observation, as the S content was found to be 4.62 wt% (1.4437 mmol g−1) (Fig. S3g). Before sulfonation (Fig. S3d,e), there was a quantitative presence of C, O, Mg, Si, P, Cl and K, while after sulfonation in the SEM–EDX spectrum of BP-SO3H (Fig, S3f,g) it could clearly be seen that there is increase of carbon amount with less irregularity and increase of porosity due to simultaneous carbonization and sulfonation. The elemental mapping also confirmed the distribution of carbon (red), oxygen (yellow), and sulfur (green) for the BP-SO3H catalyst.
Figure 3 shows XPS analysis which was carried out on the acid-functionalized catalyst BP-SO3H. C, O, and S were visible in the spectrum. In the deconvoluted spectrum of the C1s region, major peaks at 287 eV and 282 eV are assigned to C=O and C=C, respectively (Fig. 3a). Similarly, the O1s (Fig. 3b) region showed peaks at 535 and 530 eV for C=O and C–O, respectively56. XPS also demonstrates the presence of a sulfonic group in the catalyst. As seen in Fig. 3c, the strong S2p peak at 170 eV corresponds to the –SO3H group60. This means that most of the S in the sample is in the form of –SO3H. On the other hand, a peak at 171 eV (weak) exists, which suggests a minute quantity of –O–SO3H61.
Data analysis and modeling using the response surface method (RSM)
The relationship between responses (% yield) and reaction variables A-D (see "Parametric optimization by response surface methodology (RSM)" section) was analyzed using RSM. CCD technique is a partial factorial design method with the center point amplified with a gathering of the axial point that grants evaluation of non-linearity in the predicted model. For the developments of CCD, the number of experiment (N) is calculated by N = 2n + 2n + m, where n is the number of independent variables and m is the number of replicated central point42. For the current system, n = 4 and m = 6. This forms a set of 16 cube points, 8 axial points, and six repeated center data; thus total 30 experiments run (refer to Table 2), which are analyzed in a randomized order where axial point, α = 0.05. A series of thirty experiments were conducted and the results of each CCD experiment along with biodiesel yield are shown in Table 2.
The actual biodiesel yield in experiments ranged from 61.4 to 97.9%. Moreover, Eq. (8) describes the biodiesel yield affected by the coded factors A–D (see the experimental variables A–D in Table 3).
ANOVA study of the process
ANOVA was used to determine the statistical significance of the model equation and the effects of the terms and their interactions on biodiesel yield to evaluate the significance and fitness of the quadratic regression model. Table 3 indicates the ANOVA results for the yield of OA to biodiesel. At the 95% confidence level, the regression model's F-value (Fischer test, which determines the significance of the chosen model and individual parameter affecting the response) of 295.47 and p-value < 0.0001 (probability of error, with < 0.05 representing significance) shows that it is statistically significant62,63. As shown in Table 3, A, C, D, AB, AC, AD, BC, BD, CD, A2, B2, C2, and D2 are significant, while B is not a significant model term. Several statistical parameters were used to assess the accuracy of the regression equation, including the coefficient of determination (R2), the adjusted R2, and adequate precision.
As described by the regression model equation, the R2 value of 0.9964 indicates that the regression model can explain 99.7% of the variation in biodiesel yield. Thus, the developed model correlates well with actual and predicted biodiesel yields64. This was supported by the adjusted R2 of 0.9930, excluding non-significant terms in the model. The model yielded a precision of 63.35 (a value greater than 4 is always preferred)65. According to the value obtained, the signal is adequate, and the regression model is useful for directing the design space for the experimental results64. A value of ˂ 10% indicates that the experimental values correlate with the model's predicted values66.
Diagnostic plots (Fig. 4) were used to evaluate the quality of the regression model developed in this study. Figure 4a depicts a correspondence OA's actual and predicted yield. It indicates a good response estimation concerning changes in the independent variable A–D since data points are close to the fit regression line. It is crucial to check whether the regression model is acceptable by assessing if the residuals have a normal distribution. In experiments, residuals are the differences between actual and predicted values and represent how well the model fits the assumptions of ANOVA.
Figure 4b shows the plot of normal distribution versus studentized residuals. The plot implies that most of the data follow a straight line rather than the abnormal S-shape indicating studentized residuals follow a normal distribution67.
In Fig. 4c, the studentized residuals are displayed against the predicted yield. The residuals are distributed randomly in the plot, suggesting that the original observation is not related to the response values, as suggested by the model. As a result, the response parameter does not need to be transformed.
Figure 4d illustrates the residuals vs. the experimental run. Due to the presence of noise in the experiments, the residual differences between the experimental runs are large. The abscissa represents the number of experiments, whereas the ordinate represents the studentized residuals. All residuals fall within the range of 4.00, indicating that the fitted model accurately approximates all data with no errors recorded68.
Perturbation plots (Fig. 5) help classify the process variables' effect on yield while keeping the other process variables constant at an intermediate level69. The nature of the curvature represents the variability A–D factors on the biodiesel yield. The factor with a steeper slope more prominently affects biodiesel yield than with a flatter slope70. The plot (Fig. 5) illustrates factor A's prominent effect on biodiesel yield, followed by D, C, and B; similarities can be seen in ANOVA Table 3. Figure 5 shows that the molar ratio (A) at the lower level till the middle value is more sensitive; in contrast, the sensitivity is reduced between the middle and higher levels. Between intermediate to higher level parameter, B and D has a prominent effect on yield. Above the intermediate level, variation in biodiesel yield is moderate compared to the below-intermediate range. As per the ANOVA analysis, the molar ratio (A) is the most significant factor affecting the yield.
Interaction effects of process input variables on OA biodiesel yield
In order to measure the influence of independent parameters A–D (viz., A = MOMR; B = catalyst loading; C = time; and D = temperature) on experimental biodiesel yield obtained through microwave heating, 3D response surface plots were used70. The effect of MOMR and catalyst loading on biodiesel yield is shown in Fig. 6a. By increasing both the variables, biodiesel yield also increased until it reached its maximum of 8 wt% catalyst loading and a MOMR of 20:1. A moderate decrease in yield was observed when the reaction period was prolonged beyond optimum value due to esterification's reversibility67. According to the 3D response curve, the interaction between MOMR and catalyst loading significantly affects the reaction.
The relationship between MOMR and reaction time is depicted in Fig. 6b. By prolonging the reaction time from 45 to 65 min, no significant improvement was observed in the yield efficiency at low methanol to the oleic acid molar ratio (specify the range). However, it showed considerable variations, with a maximum yield at 20:1, whereas altering duration had little effect.
Figure 6c shows the effect of MOMR and temperature interaction on OA yield. The yield increases with increasing both factors until it reaches its center maximum of 98.2% at 20:1 MOMR and 80 °C, which declines modestly. This can be attributed to excessive methanol diluting the reaction mixture71 and thus allowing water to be introduced, reinitiating the reverse reaction72. MOMR and temperature interact strongly in this reaction, as seen in the 3D response curve.
Figure 6d illustrates the effect of the catalyst dosage and reaction time on biodiesel yield. With an increase in the amount of catalyst, oleic acid yield increased drastically as more active sites were provided. Despite the further increase in catalyst concentration, the maximum yield of oleic acid to methyl oleate was observed at 8 wt%. The maximum yield was observed at 55 min, after which it declined due to the reversibility of esterification reaction73.
Figure 6e shows the interaction of catalyst loading and temperature. The methyl oleate yield was highest at 8 wt% and 80 °C, respectively. Due to the endothermic nature of esterification, an increase in temperature resulted in initially increased yield74. At higher temperatures, there was a drop in yield due to methanol evaporation75.
Figure 6f illustrates the interaction of reaction time and temperature. As the temperature initially increased, methyl oleate yield increased to 98.2% at 80 °C and 55 min. Both factors show significant interaction. Considering these data, 55 min of reaction time, 80 °C of temperature, 8 wt% of catalyst loading, and a MOMR of 20:1 has been concluded as the optimal conditions for the given microwave-assisted esterification reaction.
Analysis of 1H NMR and 13C NMR
Fig. S6a, given in the SI shows the 1H NMR spectrum of methyl oleate (biodiesel). A singlet signal at 3.62 ppm represents methoxy protons in the methyl ester. A triplet signal at 2.26 ppm represents the α-CH2 protons in the methyl ester (–CH2CH2COOMe). It is evident from these two peaks that there are methyl esters in biodiesel. A triplet signal of 0.84 ppm was observed as the result of the terminal methyl protons, a strong multiplet signal at 1.22 ppm was observed from the methylene protons of the carbon chain, a multiplet was observed at 1.57 ppm from the β-carbonyl methylene protons (-CH2CH2COOMe), a multiplet at 1.97 ppm and another at 5.30 ppm was detected from the olefinic hydrogen76,77. 1H-NMR revealed 99.5% biodiesel conversion by triplet integration at δ 2.28 ppm for methyl oleate (using the formula given in (Eq. 3))78. Furthermore, biodiesel yield of 97.9% was calculated using Eq. (4) under the same optimized condition.
Fig. S6b shows the 13C NMR spectrum of methyl oleate (biodiesel). The carbonyl carbon of the ester molecules (–COOMe) is represented by the signal at 174.8 ppm, whereas the signal at 130.5 ppm represents the olefinic carbons. Methoxy carbons of methyl esters (–COOMe) are responsible for the signal at 52 ppm in the 13C NMR spectra of biodiesel. The fatty acid moiety's methylene and methyl carbons are found in the range of 14.6 to 34.6 ppm79.
Kinetic study of oleic acid esterification
Figure 7a,c showed a linear relationship between −ln(1−X) Vs. time and X/(1−X) Vs. time for reactions carried out at different temperatures ranging from 50 to 80 °C. The plots in Fig. 7a–d represent pseudo-first and second-order reaction kinetics based on the Eqs. (9) and (10), respectively. The activation energy was determined by different rate constants and the Arrhenius equation (Eq. 11). Upon comparing the linear regression coefficients (R2) it was found that the pseudo-first-order reaction kinetic model had a higher R2 value of 0.9961 than the second-order kinetic model having R2 value of 0.9742. This indicated that the constructed pseudo-first-order kinetic model is more plausible. The esterification reaction's activation energy (Ea) was determined by substituting the rate constants in the Arrhenius equation (Eq. 11). From the line's intercept and slope (−Ea/R), the pre-exponential factor and Ea for the reaction can be inferred, respectively75. From Fig. 7b, Ea was found to be 48.53 kJ mol−1, which comes in the range of 24.7–84.1 kJ mol−146,80. It showed that the current catalyst induces a substantial decrease in activation energy compared to various other esterification catalysts. These include Al-Sr nanocatalyst (72.9 kJ mol−1)81, CaO/SiO2 (66.3 kJ mol−1)80 and H3PW12O40 (51.0 kJ mol−1)82. The pre-exponential factor in the present study was calculated to be 1.1 × 106 min−1.
Test for heterogeneity and catalyst reusability
A heterogeneity test for the BP-SO3H-15-18-100 catalyst was performed using the "hot filtration method (Sheldon's test)"47. The catalyst was separated by filtration under hot conditions after 35 min of reaction, and a yield of 85% was observed. Then, the reaction was continued for another 30 min with catalyst-free, where the yield of the product, 86.6%, was achieved (see SI, Fig. S6). This study confirmed that an insignificant amount of soluble active species in the filtrate could no longer increase catalytic activity. Hence, the catalyst displayed heterogeneous nature. One of the key benefits of employing a heterogeneous catalyst for biodiesel synthesis is that the catalyst may be reused, reducing biodiesel production costs significantly. Authors can anticipate the economic viability of biodiesel production at a commercial scale using reusability analyses. The synthesized banana peel catalyst was subjected to repeated catalytic cycles under optimal conditions (20:1 MOMR, 8 wt% catalyst loading, 80 °C, 55 min) to study its reusable nature. Each catalytic run was followed by filtration and methanol wash to recover the catalyst. The recovered catalyst was dried in a vacuum oven at 80 °C overnight before being used in subsequent cycles. OA yield to methyl ester progressively declined with every subsequent cycle, eventually reaching 80% in the fifth cycle (Fig. 8). Methylation of sulfonic acid groups83 and leaching83,84 were the major causes that contributed to the decline in oleic acid yield in each reaction cycle. SEM and EDX of the recovered catalyst (Fig. S7) were performed, and there was observed a decrease in the level of sulfur content from 4.62 wt% (1.4437 mmol g−1) of fresh catalyst to 3.08 wt% (0.9625 mmol g−1) of recovered catalyst.
Comparison of the present catalyst with the reported catalyst for esterification of OA to biodiesel
Table 4 compares the efficacy of the catalyst BP-SO3H to other reported acid-functionalized esterification catalysts. A majority of these proved successful in converting OA to FAME (excluding entry 11); however, drawbacks include high MOMR (entries 8,11,12), high catalyst loading (entries 3,4,9,10), elevated temperature (1,4,7,8,9,11), and long reaction time (entries 1–9). The turnover frequency (TOF, Eq. S1) of most reported catalysts was lower than BP-SO3H-15-18-100, whose TOF was 0.047 mol g−1 h−1. Even though Fe3O4@ZIF-8/TiO2 achieved a higher TOF value, the requirement for high MOMR, the non-biogenic (not renewable or non-biodegradable) nature of the catalyst, and due to lower biodiesel yield, its appeal has been reduced.
Conclusion
In this work, sulfonic acid functionalized banana (Musa acuminata) peel was synthesized and used as a novel heterogeneous catalyst for biodiesel production from oleic acid as a test substrate. Successful sulfonation of M. acuminata sample was confirmed by physicochemical characterization. A single peak at 170 eV in the XPS spectrum confirmed that the sulfur in the catalyst is mainly in the form of a sulfonic acid group. An RSM-CCD approach predicted a biodiesel yield of 98.2% under the optimized reaction conditions. Experimentally, microwave heating observed an actual biodiesel yield of 97.9 ± 0.7%. Based on the results of this study, the RSM-CCD approach can be used to forecast biodiesel synthesis under a range of conditions, allowing for subsequent synthesis to be more effective. The catalyst showed excellent stability on repeated reuse without much loss in its activity, where a high conversion of 82.2 ± 0.5% methyl oleate biodiesel was observed on the fifth catalytic cycle. The yield decreased mainly due to sulfur leaching from 4.62 wt% (fresh) to 3.08 wt% (5th recycled), which was detected by SEM–EDX analysis. Thus, compared to synthetic catalysts, which are toxic, unsustainable, expensive, and non-biodegradable. The current catalyst has a profound impact on environmental conservation.
Data availability
The datasets used and/or analyzed during the current study available from the corresponding author on reasonable request.
References
Gebremariam, S. N. & Marchetti, J. M. Economics of biodiesel production: Review. Energy Convers. Manag. https://doi.org/10.1016/j.enconman.2018.05.002 (2018).
Helwani, Z. et al. Conversion of Jatropha curcas oil into biodiesel using re-crystallized hydrotalcite. Energy Convers. Manag. 73, 128–134 (2013).
Gouda, S. P. et al. Microwave-assisted biodiesel production using UiO-66 MOF derived nanocatalyst: Process optimization using response surface methodology. Catalysts 12, 1312 (2022).
Maheswari, P. et al. A review on latest trends in cleaner biodiesel production: Role of feedstock, production methods, and catalysts. J. Clean. Prod. 355, 131588 (2022).
Ao, S. & Rokhum, S. L. Recent advances in the valorization of biodiesel by-product glycerol to solketal. J. Chem. 2022, 1–18 (2022).
Changmai, B., Vanlalveni, C., Ingle, A. P., Bhagat, R. & Rokhum, L. Widely used catalysts in biodiesel production: A review. RSC Adv. 10, 41625–41679 (2020).
Gouda, S. P., Dhakshinamoorthy, A. & Rokhum, S. L. Metal-organic framework as a heterogeneous catalyst for biodiesel production: A review. Chem. Eng. J. Adv. 12, 100415 (2022).
Laskar, I. B. et al. Waste snail shell derived heterogeneous catalyst for biodiesel production by the transesterification of soybean oil. RSC Adv. https://doi.org/10.1039/c8ra02397b (2018).
Alagumalai, A., Mahian, O., Hollmann, F. & Zhang, W. Environmentally benign solid catalysts for sustainable biodiesel production: A critical review. Sci. Total Environ. https://doi.org/10.1016/j.scitotenv.2020.144856 (2021).
Gouda, S. P. et al. Microwave assisted biodiesel production using sulfonic acid-functionalized metal-organic frameworks UiO-66 as a heterogeneous catalyst. Renew. Energy 197, 161–169 (2022).
Bayat, A., Baghdadi, M. & Bidhendi, G. N. Tailored magnetic nano-alumina as an efficient catalyst for transesterification of waste cooking oil: Optimization of biodiesel production using response surface methodology. Energy Convers. Manag. 177, 395–405 (2018).
Alaei, S., Haghighi, M., Toghiani, J. & Rahmani Vahid, B. Magnetic and reusable MgO/MgFe2O4 nanocatalyst for biodiesel production from sunflower oil: Influence of fuel ratio in combustion synthesis on catalytic properties and performance. Ind. Crops Prod. 117, 322–332 (2018).
Saikia, K. et al. Sulphonated biomass-based catalyst for solketal synthesis by acetalization of glycerol—A byproduct of biodiesel production. Fuel Process. Technol. 238, 107482 (2022).
Das, A., Shi, D., Halder, G. & LalthazualaRokhum, S. Microwave-assisted synthesis of glycerol carbonate by transesterification of glycerol using Mangifera indica peel calcined ash as catalyst. Fuel 330, 125511 (2022).
Noriega, M. A., Narváez, P. C., Cadavid, J. G. & Habert, A. C. Modeling of biodiesel production in Liquid-Liquid Film Reactors including mass transfer effects. Fuel Process. Technol. 167, 524–534 (2017).
Ruatpuia, J. V. L. & Rokhum, S. L. Biodiesel production through heterogeneous catalysis route: A review. 2022, 1–19 (2022).
Leung, D. Y. C., Wu, X. & Leung, M. K. H. A review on biodiesel production using catalyzed transesterification. Appl. Energy https://doi.org/10.1016/j.apenergy.2009.10.006 (2010).
Eldiehy, K. S. H. et al. Towards biodiesel sustainability: Waste sweet potato leaves as a green heterogeneous catalyst for biodiesel production using microalgal oil and waste cooking oil. Ind. Crops Prod. 187, 115467 (2022).
Eldiehy, K. S. H. et al. Radish (Raphanus sativus L.) leaves: A novel source for a highly efficient heterogeneous base catalyst for biodiesel production using waste soybean cooking oil and Scenedesmus obliquus oil. Renew. Energy 191, 888–901 (2022).
Zhang, Y., Dubé, M. A., McLean, D. D. & Kates, M. Biodiesel production from waste cooking oil: 2. Economic assessment and sensitivity analysis. Bioresour. Technol. 90, 229–240 (2003).
Lathiya, D. R., Bhatt, D. V. & Maheria, K. C. Synthesis of sulfonated carbon catalyst from waste orange peel for cost effective biodiesel production. Bioresour. Technol. Rep. 2, 69–76 (2018).
Khan, H. M. et al. Application of agricultural waste as heterogeneous catalysts for biodiesel production. Catalysts https://doi.org/10.3390/catal11101215 (2021).
Zhao, C. et al. Biodiesel synthesis over biochar-based catalyst from biomass waste pomelo peel. Energy Convers. Manag. 160, 477–485 (2018).
Agarwal, M., Chauhan, G., Chaurasia, S. P. & Singh, K. Study of catalytic behavior of KOH as homogeneous and heterogeneous catalyst for biodiesel production. J. Taiwan Inst. Chem. Eng. 43, 89–94 (2012).
Meher, L. C., Vidya Sagar, D. & Naik, S. N. Technical aspects of biodiesel production by transesterification—A review. Renew. Sustain. Energy Rev. 10, 248–268 (2006).
Aranda, D. A. G., Santos, R. T. P., Tapanes, N. C. O., Ramos, A. L. D. & Antunes, O. A. C. Acid-catalyzed homogeneous esterification reaction for biodiesel production from palm fatty acids. Catal. Lett. 122, 20–25 (2008).
Avinash, A. & Murugesan, A. Prediction capabilities of mathematical models in producing a renewable fuel from waste cooking oil for sustainable energy and clean environment. Fuel 216, 322–329 (2018).
Mateo, W. et al. One-step synthesis of biomass-based sulfonated carbon catalyst by direct carbonization-sulfonation for organosolv delignification. Bioresour. Technol. 319, 124194 (2021).
Mendaros, C. M., Go, A. W., Nietes, W. J. T., Gollem, B. E. J. O. & Cabatingan, L. K. Direct sulfonation of cacao shell to synthesize a solid acid catalyst for the esterification of oleic acid with methanol. Renew. Energy 152, 320–330 (2020).
Shang, Y., Jiang, Y. & Gao, J. One-step synthesis of peanut shell-derived solid acid for biodiesel production. Energy Sources Part A Recov. Util. Environ. Effects https://doi.org/10.1080/15567036.2011.60302637,1039-1045 (2015).
Kumawat, M. K. & Rokhum, S. L. Biodiesel production from oleic acid using biomass-derived sulfonated orange peel catalyst. Front. Catal. 2, 1–12 (2022).
Hassan, W. A. et al. Sulfonation of natural carbonaceous bentonite as a low-cost acidic catalyst for effective transesterification of used sunflower oil into diesel; statistical modeling and kinetic properties. ACS Omega 6, 31260–31271 (2021).
Ngaosuwan, K., Goodwin, J. G. & Prasertdham, P. A green sulfonated carbon-based catalyst derived from coffee residue for esterification. Renew. Energy 86, 262–269 (2016).
Achparaki, M. et al. Central composite design for response surface methodology and its application in pharmacy. 13 (Intech, 2012).
Dhawane, S. H., Kumar, T. & Halder, G. Central composite design approach towards optimization of flamboyant pods derived steam activated carbon for its use as heterogeneous catalyst in transesterification of Hevea brasiliensis oil. Energy Convers. Manag. 100, 277–287 (2015).
Fruit: world production by type 2021 | Statista. https://www.statista.com/statistics/264001/worldwide-production-of-fruit-by-variety/.
Han, S., Kim, G. Y. & Han, J. I. Biodiesel production from oleaginous yeast, Cryptococcus sp. by using banana peel as carbon source. Energy Rep. 5, 1077–1081 (2019).
Pathak, G., Das, D., Rajkumari, K. & Rokhum, L. Exploiting waste: Towards a sustainable production of biodiesel using: Musa acuminata peel ash as a heterogeneous catalyst. Green Chem. 20, 2365–2373 (2018).
Daimary, N. et al. Musa acuminata peel: A bioresource for bio-oil and by-product utilization as a sustainable source of renewable green catalyst for biodiesel production. Renew. Energy 187, 450–462 (2022).
Oickle, A. M., Goertzen, S. L., Hopper, K. R., Abdalla, Y. O. & Andreas, H. A. Standardization of the Boehm titration: Part II. Method of agitation, effect of filtering and dilute titrant. Carbon N. Y. 48, 3313–3322 (2010).
Malins, K., Brinks, J., Kampars, V. & Malina, I. Esterification of rapeseed oil fatty acids using a carbon-based heterogeneous acid catalyst derived from cellulose. Appl. Catal. A Gen. 519, 99–106 (2016).
Thakkar, K., Shah, K., Kodgire, P. & Kachhwaha, S. S. In-situ reactive extraction of castor seeds for biodiesel production using the coordinated ultrasound—microwave irradiation: Process optimization and kinetic modeling. Ultrason. Sonochem. https://doi.org/10.1016/j.ultsonch.2018.08.007 (2018).
Sarve, A. N., Varma, M. N. & Sonawane, S. S. Response surface optimization and artificial neural network modeling of biodiesel production from crude mahua (Madhuca indica) oil under supercritical ethanol conditions using CO2 as co-solvent. RSC Adv. 5, 69702–69713 (2015).
Nandiwale, K. Y. & Bokade, V. V. Environmentally benign catalytic process for esterification of renewable levulinic acid to various alkyl levulinates biodiesel. Environ. Prog. Sustain. Energy 34, 795–801 (2015).
Li, Z. et al. Recyclable Li/NaY zeolite as a heterogeneous alkaline catalyst for biodiesel production: Process optimization and kinetics study. Energy Convers. Manag. 192, 335–345 (2019).
Wang, Y. T., Fang, Z. & Zhang, F. Esterification of oleic acid to biodiesel catalyzed by a highly acidic carbonaceous catalyst. Catal. Today 319, 172–181 (2019).
Lempers, H. E. B. & Sheldon, R. A. The stability of chromium in CrAPO-5, CrAPO-11, and CrS-1 during liquid phase oxidations. J. Catal. 175, 62–69 (1998).
Lim, S., Yap, C. Y., Pang, Y. L. & Wong, K. H. Biodiesel synthesis from oil palm empty fruit bunch biochar derived heterogeneous solid catalyst using 4-benzenediazonium sulfonate. J. Hazard. Mater. 390, 121532 (2020).
Anderson, J. M., Johnson, R. L., Schmidt-Rohr, K. & Shanks, B. H. Solid state NMR study of chemical structure and hydrothermal deactivation of moderate-temperature carbon materials with acidic SO3H sites. Carbon N. Y. 74, 333–345 (2014).
Gong, R. et al. Sulfonic-acid-functionalized carbon fiber from waste newspaper as a recyclable carbon based solid acid catalyst for the hydrolysis of cellulose. RSC Adv. 9, 28902–28907 (2019).
Parreño, R. P., Liu, Y. L., Beltran, A. B. & Carandang, M. B. Effect of a direct sulfonation reaction on the functional properties of thermally-crosslinked electrospun polybenzoxazine (PBz) nanofibers. RSC Adv. 10, 14198–14207 (2020).
Okamura, M. et al. Acid-catalyzed reactions on flexible polycyclic aromatic carbon in amorphous carbon. Chem. Mater. 18, 3039–3045 (2006).
Kang, S., Ye, J., Zhang, Y. & Chang, J. Preparation of biomass hydrochar derived sulfonated catalysts and their catalytic effects for 5-hydroxymethylfurfural production. RSC Adv. 3, 7360–7366 (2013).
Xie, Z. L., White, R. J., Weber, J., Taubert, A. & Titirici, M. M. Hierarchical porous carbonaceous materials via ionothermal carbonization of carbohydrates. J. Mater. Chem. https://doi.org/10.1039/c1jm00013f (2011).
Huang, M., Luo, J., Fang, Z. & Li, H. Biodiesel production catalyzed by highly acidic carbonaceous catalysts synthesized via carbonizing lignin in sub- and super-critical ethanol. Appl. Catal. B Environ. 190, 103–114 (2016).
Lalthazuala, S., Changmai, B., Kress, T. & Wheatley, A. E. H. A one-pot route to tunable sugar-derived sulfonated carbon catalysts for sustainable production of biodiesel by fatty acid esteri fi cation. Renew. Energy 184, 908–919 (2022).
Kuwahara, Y., Kango, H. & Yamashita, H. Catalytic transfer hydrogenation of biomass-derived levulinic acid and its esters to γ-valerolactone over sulfonic acid-functionalized UiO-66. ACS Sustain. Chem. Eng. 5, 1141–1152 (2017).
Arancon, R. A., Barros, H. R., Balu, A. M., Vargas, C. & Luque, R. Valorisation of corncob residues to functionalised porous carbonaceous materials for the simultaneous esterification/transesterification of waste oils. Green Chem. 13, 3162–3167 (2011).
Mondal, N. K. & Kar, S. Potentiality of banana peel for removal of Congo red dye from aqueous solution: Isotherm, kinetics and thermodynamics studies. Appl. Water Sci. 8, 1–12 (2018).
Siril, P. F., Shiju, N. R., Brown, D. R. & Wilson, K. Optimising catalytic properties of supported sulfonic acid catalysts. Appl. Catal. A Gen. 364, 95–100 (2009).
Liu, H., Peng, Q., Ren, J., Shi, B. & Wang, Y. Synthesis of a sulphated-group-riched carbonaceous catalyst and its application in the esterification of succinic acid and fructose dehydration to form HMF. J. Iran. Chem. Soc. 18, 2649–2656 (2021).
Welter, R. A. et al. Methyl oleate synthesis by TiO2-photocatalytic esterification of oleic acid: Optimisation by response surface quadratic methodology, reaction kinetics and thermodynamics. ChemPhotoChem https://doi.org/10.1002/cptc.202200007 (2022).
Roman, F. F. et al. Optimization and kinetic study of biodiesel production through esterification of oleic acid applying ionic liquids as catalysts. Fuel 239, 1231–1239 (2019).
Li, Y., Hu, S., Cheng, J. & Lou, W. Acidic ionic liquid-catalyzed esterification of oleic acid for biodiesel synthesis. Cuihua Xuebao/Chin. J. Catal. 35, 396–406 (2014).
Han, B. et al. Optimization of oleic acid esterification for biodiesel production using brønsted acidic ionic liquid as a catalyst. Chiang Mai J. Sci. 46, 714–726 (2019).
Annam Renita, A., Sreedhar, N. & Magesh Peter, D. Optimization of algal methyl esters using RSM and evaluation of biodiesel storage characteristics. Bioresour. Bioprocess. 1, 1–9 (2014).
Jaliliannosrati, H., Amin, N. A. S., Talebian-Kiakalaieh, A. & Noshadi, I. Microwave assisted biodiesel production from Jatropha curcas L. seed by two-step in situ process: Optimization using response surface methodology. Bioresour. Technol. 136, 565–573 (2013).
Mostafa Marzouk, N. et al. Process optimization of biodiesel production via esterification of oleic acid using sulfonated hierarchical mesoporous ZSM-5 as an efficient heterogeneous catalyst. J. Environ. Chem. Eng. 9, 105035 (2021).
Milano, J. et al. Optimization of biodiesel production by microwave irradiation-assisted transesterification for waste cooking oil-Calophyllum inophyllum oil via response surface methodology. Energy Convers. Manag. 158, 400–415 (2018).
Sharma, A., Kodgire, P. & Kachhwaha, S. S. Biodiesel production from waste cotton-seed cooking oil using microwave-assisted transesterification: Optimization and kinetic modeling. Renew. Sustain. Energy Rev. https://doi.org/10.1016/j.rser.2019.109394 (2019).
Juan, J. C., Zhang, J., Jiang, Y., Cao, W. & Yarmo, M. A. Zirconium sulfate supported on activated carbon as catalyst for esterification of oleic acid by n-butanol under solvent-free conditions. Catal. Lett. 117, 153–158 (2007).
Zhang, Y., Wong, W. T. & Yung, K. F. Biodiesel production via esterification of oleic acid catalyzed by chlorosulfonic acid modified zirconia. Appl. Energy 116, 191–198 (2014).
Shu, Q. et al. Synthesis of biodiesel from waste vegetable oil with large amounts of free fatty acids using a carbon-based solid acid catalyst. Appl. Energy 87, 2589–2596 (2010).
Changmai, B., Sudarsanam, P. & Rokhum, L. Industrial crops & products biodiesel production using a renewable mesoporous solid catalyst. Ind. Crop. Prod. https://doi.org/10.1016/j.indcrop.2019.111911 (2019).
Changmai, B., Rano, R., Vanlalveni, C. & Rokhum, L. A novel Citrus sinensis peel ash coated magnetic nanoparticles as an easily recoverable solid catalyst for biodiesel production. Fuel 286, 119447 (2021).
Tariq, M. et al. Identification, FT-IR, NMR (1H and 13C) and GC/MS studies of fatty acid methyl esters in biodiesel from rocket seed oil. Fuel Process. Technol. 92, 336–341 (2011).
Mello, V. M., Oliveira, F. C. C., Fraga, W. G., Do Nascimento, C. J. & Suareza, P. A. Z. Determination of the content of fatty acid methyl esters (FAME) in biodiesel samples obtained by esterification using 1H-NMR spectroscopy. Magn. Reson. Chem. 46, 1051–1054 (2008).
Wang, A., Zhang, H., Li, H. & Yang, S. Efficient production of methyl oleate using a biomass-based solid polymeric catalyst with high acid density. Adv. Polym. Technol. 2019, 1–11 (2019).
Park, S. H. et al. Biodiesel production from locally sourced restaurant waste cooking oil and grease: Synthesis, characterization, and performance evaluation. ACS Omega https://doi.org/10.1021/acsomega.9b00268 (2019).
Putra, M. D., Irawan, C., Udiantoro, Ristianingsih, Y. & Nata, I. F. A cleaner process for biodiesel production from waste cooking oil using waste materials as a heterogeneous catalyst and its kinetic study. J. Clean. Prod. 195, 1249–1258 (2018).
Feyzi, M. & Shahbazi, Z. Preparation, kinetic and thermodynamic studies of Al–Sr nanocatalysts for biodiesel production. J. Taiwan Inst. Chem. Eng. 71, 145–155 (2017).
Fernandes, S. A., Cardoso, A. L. & Da Silva, M. J. A novel kinetic study of H 3PW 12O 40—catalyzed oleic acid esterification with methanol via 1H NMR spectroscopy. Fuel Process. Technol. 96, 98–103 (2012).
Chen, W. et al. Sustainable carbon aerogels derived from nanofibrillated cellulose as high-performance absorption materials. Adv. Mater. Interfaces 3, 1–9 (2016).
Azargohar, R. & Dalai, A. K. Steam and KOH activation of biochar: Experimental and modeling studies. Microporous Mesoporous Mater. 110, 413–421 (2008).
Yin, P. et al. Biodiesel production from esterification of oleic acid over aminophosphonic acid resin D418. Fuel 102, 499–505 (2012).
Narkhede, N. & Patel, A. Biodiesel production by esteri fi cation of oleic acid and transesteri fi cation of soybean oil using a new solid acid catalyst comprising 12-tungstosilicic acid and zeolite Hβ. Ind. Eng. Chem. Res. 2013(52), 13637–13644 (2013).
Wang, Y. T. et al. Biodiesel production from esterification of oleic acid by a sulfonated magnetic solid acid catalyst. Renew. Energy 139, 688–695 (2019).
Wan, H. et al. Heterogenization of ionic liquid based on mesoporous material as magnetically recyclable catalyst for biodiesel production. J. Mol. Catal. A Chem. 398, 127–132 (2015).
Vieira, S. S. et al. Use of HZSM-5 modified with citric acid as acid heterogeneous catalyst for biodiesel production via esterification of oleic acid. Microporous Mesoporous Mater. 201, 160–168 (2015).
Hara, M. Biodiesel production by amorphous carbon bearing SO3H, COOH and phenolic OH groups, a solid Brønsted acid catalyst. Top. Catal. 53, 805–810 (2010).
Santos, E. M. et al. New heterogeneous catalyst for the esterification of fatty acid produced by surface aromatization/sulfonation of oilseed cake. Fuel 150, 408–414 (2015).
Dehkhoda, A. M. & Ellis, N. Biochar-based catalyst for simultaneous reactions of esterification and transesterification. Catal. Today 207, 86–92 (2013).
MoatamedSabzevar, A., Ghahramaninezhad, M. & NiknamShahrak, M. Enhanced biodiesel production from oleic acid using TiO2-decorated magnetic ZIF-8 nanocomposite catalyst and its utilization for used frying oil conversion to valuable product. Fuel 288, 119586 (2021).
Acknowledgements
We thank IIT Indore, CIF NIT Silchar, IIT Madras, IIT Bombay, IIT Roorkee, IIT Kharagpur, IASST Guwahati, and SAIF NEHU for the analysis.
Author information
Authors and Affiliations
Contributions
R.D.: writing-original draft, investigation, validation, data curation, data analysis, and conceptualization. J.V.L.R., S.P.G.: data curation, data analysis, and writing. P.K., S.B., G.H.: data analysis, writing reviewing, and editing. S. L. R.: conceptualization, investigation, data analysis, reviewing, and supervising.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Devasan, R., Ruatpuia, J.V.L., Gouda, S.P. et al. Microwave-assisted biodiesel production using bio-waste catalyst and process optimization using response surface methodology and kinetic study. Sci Rep 13, 2570 (2023). https://doi.org/10.1038/s41598-023-29883-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-29883-4
- Springer Nature Limited