Abstract
A comparative sustainability study of bioethanol production from selected starchy feedstocks that are abundantly available was carried out in this work. This is to ensure the safe, reliable, and efficient production and consumption of fuel-grade bioethanol. The analysis utilised the established economic minimum bioethanol plant capacity of 158,000 m3/annum. The processing flowsheet model utilised was the same for each feedstock. The sustainability study's economic, environmental, and energy perspectives were investigated. The economic and environmental indices were assessed using Superpro Designer and openLCA sustainability software, respectively. Exergy and lost work were subsequently estimated manually with Microsoft Excel. The economic analyses showed that the plants using cassava and sweet potato initially had the highest return on investment (ROI) of 64.41 and 41.96% respectively at a minimum of 80% plants’ capacity utilisation. The break-even point occurs at a bioethanol price of $3.27 per gallon, beyond which positive net present values were obtained for the four processes. The least profitable plant was based on sorghum recording an ROI value of 34.11%. The environmental assessment on the four selected feedstocks showed that the processes based on cassava, corn, sweet potato, and sorghum recorded encouraging global warming potential (GWP) of 0.2452, 0.2067, 2.5261, and 0.2099 kg CO2 equivalent respectively. Cassava and corn emerged as the two most economically viable feedstocks when economic parameters were adjusted to include pollutants emission/discharge costs but with a slight decrease in profitability indices. The lost work analyses showed that distillation columns were the least energy-efficient units in the four bioethanol production routes assessed, recording loss work of about 61, 68, 34, and 49 MW for cassava, sweet potato, corn, and sorghum processing plants respectively. However, the net energy balance (NEB) and energy renewability results of the four production routes showed that the processes utilising the four selected starchy biomass feedstocks are more sustainable compared to fossil fuels.
Similar content being viewed by others
Introduction
The global energy resources profile is rich in natural gas, solar, tar sand, coal, biomass, and crude oil but fossil fuel-based energy has remained the greatest energy and revenue source1. Crude oil accounts for about 53,369 TWh of global power consumption, while natural gas-based global power consumption stands at 39,063 TWh2. These figures are products of their constantly increasing consumption levels for the past few decades despite the attractive prospect possessed by other energy sources especially biofuels2.
Biofuels have been identified as low-carbon alternatives to fossil fuels because they tend to reduce greenhouse gas (GHG) emissions, and the other associated undesirable climate change impacts3. The constantly growing worldwide industrialization and overreliance on non-renewable energy sources have resulted in a huge quantity of greenhouse gases being emitted. This has led to a rise in global temperature and the attendant effect of environmental dilapidation4. The increment in worldwide mean atmospheric carbon dioxide (CO2) concentration from the pre-industrialization era of 1850 to date has been estimated at 285–419 ppm5,6 which is quite significant. In light of this, the United Kingdom meteorological office evaluates a worldwide mean surface temperature rise of about 0.97–1.21 °C between these periods, with a dominant estimate of 1.09 °C. It has also been predicted that this trend of global temperature increase will continue in subsequent years7. Furthermore, Rabaey and Ragauskas, 2014 also predicted a rise in global greenhouse gas emissions to be 50% by 2050, as a result of the utilisation of non-renewable energy-based CO2 emissions8. Therefore, in the absence of urgent and effective measures or technological modifications to curtail CO2 emissions, the global mean atmospheric concentration of CO2 and ocean temperatures will steadily increase9,10.
Fortunately, world leaders are well informed about this environmental deterioration posed by fossil fuel consumption and as such adopted an agendum of cleaner energy of the sustainable development goal in 2015. Some countries like USA and Brazil initiated a plan to realise this agendum by the use of biofuel (gasohol); 10% bioethanol and 90% gasoline (E10) in preference to the use of 100% conventional premium motor spirit (PMS) with much priority given to corn and sugarcane, as feedstocks for the bioethanol production11.
The usage of renewable sources for fuels and electricity in transport is capable of profitably achieving great decarbonisation of the transport sector and expanding energy diversification within the sector while encouraging modernization and providing jobs in the Union economy and minimising overreliance on energy importations12.
However, the reliance on first-generation (consumables) bioethanol feedstocks has prompted great concern and opinions on whether its fulfillment will not engender the risk of food scarcity12. Meanwhile, second-generation biofuel production utilizes uneatable materials but the financial involvement in its large-scale production has hindered its growth. Recently, attention has been shifted to third and fourth-generation biofuels with greater emphasis on the use of algae and genetically modified microorganisms, respectively12. These probable interwoven consequences of food shortage from the utilization of food crops to ensure energy security have made the second, third, and fourth-generation feedstocks (lignocellulosic) more attractive12. Nevertheless, decisive measures can be put in place by governments and other stakeholders to replace the obsolete traditional farming practices with modern mechanized techniques to ensure improved acreage yields of these food crops for sustainable biofuel policies and food security.
The economic viability of bioethanol production using different feedstocks is dependent on factors such as local cost and composition of the feedstocks, energy cost, technology alternatives, plant capacity, etc. The sustainability of bioethanol production with respect to economic, environmental, and social indices has been carried out for some starchy feedstocks when utilised in different countries and/or under different conditions3,4,12,13,14,15. Consideration of these sustainability indicators requires the stepwise analysis of bioethanol produced from different starchy feedstocks in different climes. Despite this bright global prospect for biofuel production, no work has been reported on the sustainability assessment of bioethanol production from this abundant tuber and grain starchy feedstocks. Thus, sustainability analysis of bioethanol production with these feedstocks is essential to assist policymakers and bioethanol producers in feedstock selection.
In this work, a sustainability study of bioethanol production from cassava, sweet potato, corn, and sorghum was carried out as well as a comparative assessment of the technological pathways utilising the feedstocks.
Methodology
Process technology selection
The dry grind milling method was chosen for the starchy feedstocks because it has been identified to be cheaper and produce a higher yield of bioethanol than the wet milling process16. Separate hydrolysis and fermentation (SHF) was selected in preference to simultaneous saccharification and fermentation (SSF) for maximum starch-to-glucose conversion17. Two enzymes in separate reactors (alpha-amylase in alkaline (ammonia) medium, the temperature of 100 °C, a pressure of 1.013 bar, and 0.082% dried base) and glucoamylase (in sulphuric acid medium, the temperature of 60 °C, pressure of 1.013 bar, and 0.11% dried base) was selected for saccharification18. The selected temperatures and pressures have been established as the optimum conditions for alpha-amylase and glucoamylase activities in their respective medium. More so, alpha-amylase and glucoamylase-based hydrolysis are associated with a high rate of glucose yield, exceptional resistance of the enzymes to denaturation, especially at high temperatures, and reduced viscosity of the starchy medium19. Saccharomyces cerevisiae was selected as the fermentation organism for its cost-effectiveness and efficient glucose conversion20. The ideal fermentation conditions (temperature of 32 °C and pressure of 1.013 bar for 48 h) were selected21.
Double-effect distillation columns were the chosen distillation technology as they promote energy savings at a low cost22. while the first column performed at best condenser temperature (107.6 °C) and reboiler condition (111.3 °C pressure is 1.013 bar), the other performed at condenser temperature (84.1 °C) and reboiler condition (99.9 °C and pressure of 1.013 bar) for ethanol recovery. This approach concentrated the bottom of the first column and solids of the pretreatment section in a multi-effect evaporator. The dried solid was collected to be sold as animal feed. The bottom of the second column and the evaporator joined the distillation feed stream. The cost of the hydrophilic membrane, the complexity of installing pervaporation, and solvents recovery costs for azeotropic and extractive distillations23 favour the selection of molecular sieve adsorption process (operating at a contact time of 7.36 min, approach speed of 529.088 cm/s, the temperature of 85 °C and pressure of 1.013 bar) for the four processes in dehydration.
Process simulation and economic analysis
Having selected the technologies as described in “Process technology selection” section a continuous process of 90% (329 days = 7896 h) annual running time24 was input in the Superpro Designer simulation startup window. The process flow models for the selected technologies were represented in the Superpro Designer simulation environment. Updated engineering plant and raw material costs were estimated using cost indices for November 201625 which were 100.3 and 99.7 respectively, and November 2013 (106.8) as the base cost using Eq. (1).
where, X = year 2013, Y = November, 2016.
The economic parameters extracted from Sinnott et al., (2005) as given in Table 1 were input in the ‘Economic Evaluation Parameter’ window, and a startup period of 4 months was input into the ‘Time Valuation’ window24. The discounted cash flow parameters presented in Table 2 and the discount rate of 15.5%26 were input on the ‘Finances’ window. The indirect and fixed costs presented in Table 1 were input on the ‘Main Section’ window comprising capital cost and operating cost adjustments panes. The cost and size of equipment on flow models were registered on ‘Equipment Data’ panes.
Similarly, the costs of feedstocks were registered on the ‘Pure Component’ pane. The prices were registered on a per-kilogram basis and the price of the products (ethanol) was set at $3.27 per gallon27. The average cost of co-product (electricity) was set at $0.047/kWh. Utility steam and cooling water requirement costs within the programme were set at US$ 17.08 per 1000 kg and US$ 0.1 per 1000 kg respectively11. The exchange rate used was $ = ₦43726. The costs of major equipment were obtained from equipment suppliers and erectors28. Equipment of varying capacities from received quotations had their costs adjusted using the scaling expression given by Eq. (2).
where C = current cost, dollars, C0 = base cost, dollars, Q = current capacity, Qb = base capacity, I = current index, dimensionless, Io = base index, dimensionless n = exponent number or cost factor.
Prices of cassava, sweet potato, maize, and sorghum per kg are presented in Table 3. The equivalent revenue generated from the sales of the pomases and dried distiller grains with solubles (DDGS) resulting from their conversions was also considered. The carbon dioxide produced was released because of the high cost of purification and transportation to end users.
Environmental assessment
A life cycle approach of cradle-to-grave was chosen as the assessment approach using openLCA sustainability software. This method followed the product from its primal production stage of raw materials production through to its end use. The required information was the source of material and process parameters input (agrochemicals in Table 3, raw materials and utilities obtained from Superpro Designer, and distance traveled) and output (ethanol and electricity) within the openLCA system boundary. The system boundaries included:
-
i.
Agricultural production of the feedstocks
-
ii.
Feedstocks transportation to the processing site
-
iii.
Feedstocks processing to fuel-grade bioethanol and coproducts (distillers dried grain with soluble and pomace).
Literature provided the types and amount of agrochemical input listed in Table 4. On activation, the openLCA window provided flow, process, and product interface. The flow interface was created and defined as ‘bioethanol flow’ for the four processing plants. This command led to process creation which was defined as a ‘bioethanol production process. The input and output, administrative information, parameters, allocations, and social aspects are found in the process creation window. A truck (> 35tonnes a trip from the openLCA database) with an assumed distance of 400 km considering traffic and the nature of Nigerian roads was selected. Materials for feedstock conversion were the input materials represented in openLCA while quantified bioethanol and electricity produced were registered as the output materials.
After adding input and output materials, the ‘product system’ interface was created. A new window arose for the choice of editing the parameters, input, or output data before calculating the various associated impacts. Characterisation model (CMLbaseline 2016 v2.05) for life cycle impact assessment (LCIA) incorporated in SimaProv8.0 was imported into openLCA 1.5.5 and selected as the life cycle impact method. The CML baseline characterization model was then used to run the environmental assessment results where acidification, eutrophication, global warming, human toxicity, and photochemical oxidation potentials of the four bioethanol production processes were estimated.
The environmental and economic performances of the four production routes were then established from environmental emissions/discharge and energy perspectives (net energy ratio and energy renewability). The costs of all the environmental emissions/discharge for the four selected starchy feedstocks were then estimated and added to the annual operating cost of each process. Economic parameters such as gross margin, return on investment, net present value (NPV), internal rate of return (IRR), and payback period were re-estimated to establish the financial implications of the pollutants.
Exergy/lost work analyses
Exergy analyses of the four production routes were conducted with Microsoft Excel spreadsheet using data from Superpro Designer simulations. Superpro Designer is weak with thermodynamic analysis, so Eq. (3)9 was used to estimate the total entropy of each unit. Evaluation of lost work and exergy components with Eqs. (3) to (5)30 followed subsequently. The exergy data were used to estimate the net energy ratio and renewability of the four-bioethanol production routes (see Eqs. 6 and 7).
Results and discussion
Economic analysis
Figure 1 presents the total capital investment (TCI), annual operating cost (AOC), and total revenue (TR) of the processes that convert corn, sorghum, cassava, and sweet potato to fuel-grade bioethanol.
From Fig. 1, the cassava-based plant required the highest TCI of 110 million dollars while the TCI of the other three processes fell between 88 and 94 million dollars. This variation in TCI of the four processing plants was largely due to the higher raw materials requirement of the cassava process, which is a consequence of its relatively lower bioethanol yield of 175 kg ethanol/tonne (see Table 3). The economic impact of this difference in raw material requirement was less pronounced in the annual operating costs of the cassava-to-bioethanol process. This is because of the relatively low market price of cassava in Nigeria (Table 3).
Figure 2 shows the four-bioethanol production routes' gross margin and return on investment (ROI). ROI as a measure of profitability is the fraction of a process's profit after tax (PAT) and total capital investment (TCI). Cassava-based bioethanol plant gave the highest return on investment (ROI) value of 64.41% followed by sweet potato which recorded an ROI value of 41.96%. This ROI value showed that cassava is a more economically viable feedstock for bioethanol production among the four starchy feedstocks under study followed by sweet potato.
This economic viability of cassava and sweet potato was justified by their discounted payback periods (1.5 and 2 years) and net present value (NPV) ($151,964,521 and $124,516,463) at an annual discounted rate of 15.5% (Central Bank of Nigeria report, 2022) for the four bioethanol production routes and a project lifespan of ten (10) years (see Table 5). The NPV is a measure of the current value of future cash flows. The four processes assessed recorded positive NPVs as generated with Superpro Designer software for the economic analyses. These results signify the degree of viability of the investments concerning future cash flow. The NPVs presented in Table are the overall financial involvement of the four bioethanol production pathways under reference over their lifetime with cognizance of the time value of money. The observed differences in the NPV resulted from the different initial capital investments due to the variation in equipment sizing of the four processes. The equipment sizing is a factor of raw materials requirements to produce the desired throughput (158,000 m3/annum bioethanol) from each of the feedstocks, which ultimately affects the utility cost, annual operating costs, and the overall profitability of the processes. Similarly, the internal rate of return for each of the four processes was higher than the interest rate (15.5%) from which the NPV was generated (see Table 5).
The sensitivity analyses were conducted on the four fuel-grade bioethanol production pathways with Microsoft Excel and the results showed that the desired net profit can be realized only when the plants are operated at a minimum of 80% capacity utilization. Although the profit can still be realized through a price increase of the fuel produced. However, in this case, affordability is of the essence for the gasohol policy and its implementation to rapidly gain general acceptance for environmental sustainability. The sensitivity analysis also gave a break-even point at a bioethanol price of $3.27 per gallon, beyond which positive net present values were obtained for the four processes. It can therefore be asserted based on NPV, discounted payback period, and IRR that these four processes are economically profitable and acceptable.
Environmental assessment
The environmental impact assessment was conducted using a life cycle approach of cradle-to-grave with openLCA sustainability software. This method followed the product from its primal production stage of raw materials production through to its end use. The openLCA software gave reports of global warming potential, acidification potential, eutrophication potential, photochemical oxidation potential, and human toxicity potential at a standard error of 0.077.
Global warming potential (GWP100)
From Fig. 3, the net overall greenhouse gas emissions per kg of ethanol produced (measured relative to kg CO2 equivalents) are 0.2453, 2.5261, 0.2067, and 0.2099 for cassava, sweet potato, corn, and sorghum respectively. The results show that the global warming potential was highest in sweet potatoes with carbon dioxide from fossils contributing the highest emission of 85.19% (see Table 6). This is due to the transportation of large quantities of sweet potatoes required for the process, tractor operations, and nitrogenous fertilizer application.
The application of chemical fertilizers and herbicides generally improves crop production. However, concerns have been raised not only about the severe environmental problems posed by such practices but also about their long-term sustainability29. On the other hand, the use of organic materials (e.g., animal manures, crop residues, green manures, etc.) as an alternative source holds promise. Organic farming has been expanding at an annual rate of 20% in the last decade31.
Acidification potential (AP)
Enzyme production had recently been reported to be the dominant contributor to the overall acidification burdens due to SO2 emissions from fossil fuel consumption in bioethanol production processes32. In this work, the results presented in Fig. 4 show that the process utilising sorghum recorded the highest acidification potential value of 0.0205 kg SO2 equivalent.
A large amount of nitrogenous fertilizer required to produce the needed sorghum for the set bioethanol throughput (see Table 4) is responsible for the high acidification value recorded in the sorghum process. Ammonia and nitrogen monoxide were the dominant emission contributors of 51.90% and 46.14% respectively as shown in Table 6. The sulfuric acid used in the hydrolysis of the starchy feedstocks also contributed to the acidification burden on the environment.
Eutrophication potential (EP)
Eutrophication potential is generally associated with the environmental impacts of excessively high nutrients (such as N and P) that lead to shifts in species composition and increased biological productivity33.
Among the bioethanol production processes assessed, bioethanol produced from sweet potatoes was the dominant contributor to the eutrophication burden as seen in Fig. 5. From Table 6, phosphorus constituted 87.04% of the overall emissions in the sweet potato process due to excessive liming material application, which is consequent to its relatively low yield of bioethanol.
Although corn, sorghum, and cassava require larger amounts of liming material, the overall quantity of sweet potato needed to actualize the desired bioethanol throughput is larger because of its lower bioethanol yield (Table 3).
Photochemical oxidation potential (POP)
Photochemical oxidation also referred to as summer smog is the result of reactions between NOx and hydrocarbons or volatile organic compounds (VOCs)33. The four selected processes showed close photochemical oxidation burdens of 0.0089, 0.0067, 0.0076, and 0.0082 kg ethylene equivalent for cassava, sweet potato, corn, and sorghum respectively (Fig. 6). However, the photochemical oxidation impact of the cassava process was slightly higher due to excessive nitrogenous fertilizer utilization and excessive raw material requirements for the set throughput. Octane emission was the only contributor to the cassava and corn processes (Table 6).
Human toxicity potential-(HTP)
The human toxicity potential (HTP) of each emission of the emitted toxic substance into the air, water body, and soil is often measured relative to 1,4-dichlorobenzene (1,4-DB) and is expressed as kg 1,4 DB equivalent. The principal HTP in the four processes was derived from the hydrolysis phase, which involves the use of acid. Sorghum was the dominant contributor to human toxicity burden (recording 0.0142 kg 1,4-DB equivalent as shown in Fig. 7) with nitrogen oxide contributing about 95.14% as shown in Table 6, while cassava, corn, and sweet potato recorded 0.0006, 0.0046, and 0.0107 kg 1,4-DB equivalent respectively.
Figure 8 compares the global warming potentials of the four-bioethanol production routes with that of gasoline production processes. The differences between all four routes and gasoline production are quite pronounced.
The sweet potato process recorded the highest value of greenhouse gas (GHG) emissions among the four processes. This can be attributed to fossil fuel combustion derived from tractor activities (such as bush clearing, ploughing, planting, mineral fertilizer application, and harvesting). The impact of the high global warming burden of the sweet potato process was also demonstrated in Fig. 9 where the “avoided emissions” is least for the bioethanol production process utilising sweet potato.
The environmental performances (concerning global warming, acidification, eutrophication, photochemical oxidation, and human toxicity burdens) of bioethanol production processes from the selected feedstocks were critically assessed and the processes were ranked accordingly as shown in Table 7.
The high level of consistency displayed by corn and cassava through economic and environmental sustainability assessment indicators proves that they are the most viable of the selected four starchy feedstocks. Cassava and sweet potato stood first and second in the economic assessment with return on investment of 64.41% and 41.96%. However, the difference in the economic performances of corn and sweet potato is insignificant as evident from Fig. 2. This profitability of cassava and corn processes matched their environmental performances, recording the least environmental burdens from their respective categories (see Figs. 4, 5, 6, 7 and 8) and the best avoided greenhouse gas emission result (see Fig. 9). It is obvious from the results that corn showed attractive economic trends but was partly overshadowed by its net energy balance (NEB) presented in “Net energy balance (NEB) and energy renewable” section.
Net energy balance (NEB) and energy renewable
Table 8 presents the net energy balance (NEB) which is the ratio of the total energy of the bioethanol produced to the net energy consumed in the course of bioethanol production. From the results presented in Table 8, it can be seen that the bioethanol production process utilizing cassava was the most energy effective of the four processes.
Table 9 depicts the energy renewability of the selected feedstocks. This is a ratio of the energy of the fuel-grade bioethanol produced to the net fossil energy consumed. The results showed that sweet potato and cassava consumed the least amount of fossil energy among the four production pathways. This observation could be traceable to the fact that sweet potato does not require the addition of herbicides and formicide (see Table 4).
Table 10 presents the pollutant emission and discharge costs used in this work.
From Table 11, carbondioxide constitutes over 90% of the total emission costs for all the bioethanol production processes studied in this work. Sweet potato and cassava processes recorded the highest emissions of carbon dioxide of 4 691 641 and 454 766 tonnes/annum respectively. From the material balance results, the cassava conversion process to fuel-grade bioethanol produced 1625 tonnes/annum CO2 out of the 30 317 tonnes/annum, while that of the sweet potato process produced 1374 tonnes/annum CO2 out of 312 776 tonnes/annum as shown in Table 11. The remaining 28 692 and 311 402 tonnes/annum of CO2 from cassava and sweet potato processes emanated from fossil fuel combustion derived from bush clearing, ploughing, planting, mineral fertilizer application, harvesting, and subsequent transportation of the feedstocks to the processing site as summarized in Table 11. This fossil fuel-derived CO2 emission constituted a system bottleneck in the feedstock production phase.
Upon assigning emission/discharge costs to the environmental pollutants as presented in Table 11, the overall emission cost of each processing plant was added to its annual operating cost and the economic parameters were re-evaluated as presented in Table 12. It was found that cassava maintained its status as the most economically viable bioethanol feedstock among the starchy feedstocks under study. Although there was a slight decrease in its ROI values (see Table 12). The economic profitability of the sweet potato process was greatly reduced by excessive carbondioxide emission and therefore, outperformed by the corn-to-bioethanol process.
Exergy analyses
Figure 10 depicts the exergy efficiencies of the four bioethanol production routes using the values generated with Superpro Designer in a Microsoft Excel spreadsheet. The highest exergy efficiencies for cassava, corn, and sorghum processes were observed in the adsorption columns. This is understandable as the interaction of the fluid in the adsorption column is largely mass transfer with little or no heat exchange. This varied slightly for a sweet potato-to-ethanol process where the highest exergy efficiency was observed at the degasser section due to the negligible difference in temperatures of utility high-pressure steam and the preheated fermentation broth. Degas vent condenser units recorded the least exergy efficiencies for all four-bioethanol production plants. This low efficiency can be attributed to the relatively high heat energy content of the carbondioxide leaving the degas condenser which causes most of the heat supplied by steam to be lost.
Lost work analysis
Table 13 presents the lost work results obtained from processing the four-bioethanol feedstocks. From the results obtained, distillation columns constituted the highest lost work of over 50% in all four processes (see Table 13). The sorghum plant recorded the highest total lost work among the four starchy feedstocks. This is traceable to higher materials and utility requirements in the sorghum process. The corn processing plant recorded the least total lost work of 64 MW and therefore outperformed cassava, sweet potato, and sorghum from an energy efficiency perspective. This high-energy loss in the distillation column was therefore identified as the system bottleneck in the feedstocks processing phase for the four-bioethanol production processes considered in this work. Hence, it can be inferred that cassava and corn are the best bioethanol feedstocks upon a considerable tradeoff among economic, energy, and environmental perspectives.
Feedstocks production
Carbondioxide emissions in the feedstock production phase were derived from fossil fuel combustion from tractor operations (such as bush clearing, ploughing, and planting, mineral fertilizer application, pesticide application, harvesting, and processing) as estimated in Table 14. Mineral fertilizer usage is the major contributor to CO2 emission in corn production with about 62% of the overall CO2 released31 while a similar process in cassava production contributes about 30.15% of CO234. Hence, mineral fertilizer application was identified as a feedstock production phase bottleneck. According to the findings of Tongwane et al. (2016), and Nguyen et al. (2007), the use of compost manure derived from decayed plant residue left in the field is capable of reducing CO2 emission by 62% and 30.15% for corn and cassava productions respectively with the corresponding reduction in annual operating costs by $129 760, and $72 475 respectively as expressed in Table 14. This is justifiable, as the crop yield with compost manure usage for various crops is higher compared to mineral fertilizers utilization29.
Feedstocks processing
The feedstock processing phase bottleneck was identified to be the distillation column with 61 MW and 32 MW of lost work in cassava and corn processing plants respectively. These figures amount to 59.81 and 53.44% of the total energy losses in their respective processes. As a way of reducing energy losses in fermentation broth purification, Suleiman et al. (2014) suggested the use of a hybrid configuration of a totally heat-integrated distillation column (THIDC) and molecular sieve adsorption column35. His study on the exergo recycled stream-economic assessment of bioethanol refining showed that energy savings of 61.8% could be achieved with the use of THIDC and molecular sieve hybrid configuration. The adoption of this hybrid configuration in this work is capable of reducing the cost of utility by $2827.81 and $1588.66 for the cassava and corn processing plants respectively as presented in Table 15.
Conclusion
A sustainability study of four selected starchy feedstocks (cassava, sweet potato, corn, and sorghum) for bioethanol production was conducted to include economic, environmental, and energy indicators. The four-bioethanol production routes were found to be economically viable recording ROI values of 64.41, 41.96, 40.89, and 34.11% for cassava, sweet potato, corn, and sorghum processes respectively. While all the processes recorded positive NPVs for a discounted rate of 15.5% and a 10-year project span, the sensitivity analyses revealed an important constraint to the four processes, which limit the capacity utilization of the production routes to a minimum of 80% per annum below which the projects recorded losses. The four processes were also observed to be environmentally favorable from an energy perspective as they recorded net energy balance values of greater than 1. The four processes portrayed appreciable economic viability (recording new ROI values of 54.11, 36.51, 40.59, and 34.11% for cassava, sweet potato, corn, and sorghum processes respectively) despite adjusting the economic parameters to include pollutants emission/discharge costs. Because of the huge impact, carbon dioxide emission cost had on the sweet potato process, the final ROI value of the sweet potato process fell below that of the corn-based bioethanol process. As such cassava and corn-based bioethanol production processes represent the two most sustainable bioethanol production routes. The two production routes (cassava and corn-based processes) recorded a total lost work of 101 MW and 64 MW respectively. As a way of enhancing the energy and environmental performances of the best two processes, which would ultimately translate into better economic prosperity, compost manure utilisation and hybrid configuring of thermally integrated distillation column (THIDC) were suggested to minimize CO2 emissions and lost work in the feedstock production and processing phases respectively. The major limitations to this research work are the insufficiency of a reliable database on costs of feedstocks and materials with their variations, fluctuations in currency exchange rates, and the cost of acquiring licensed software that contains all the information of the selected feedstocks. Further comparative sustainability studies concerning these three indicators (economic, environmental, and energy) should be conducted simultaneously on more attractive third and fourth-generation bioethanol feedstocks.
Data availability
The supporting data from which the results of this work were generated are openly available in the following links presented in Table
Abbreviations
- FAO:
-
Food and Agricultural Organisation
- FEWS:
-
Famine Early Warning System
References
Ogundare, I. O. Techno-Economic Assessment of Biofuel as an Alternative Energy Source for Transportation in Nigeria. Technology Planning and Development Unit, Obafemi Awolowo University, Ile-Ife (MSc Thesis)-Unpublished (2010).
Global fossil fuel consumption. Our World in Data. Retrieved October 14, 2022, from https://ourworldindata.org/grapher/global-fossil-fuel-consumption (2022).
Jeswani, H. K., Chilvers, A. & Azapagic, A. Environmental sustainability of biofuels: A review: Environmental sustainability of biofuels. In Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences (Vol. 476, Issue 2243) (Royal Society Publishing, 2020). https://doi.org/10.1098/rspa.2020.0351.
Wang, X., Huang, J. & Liu, H. Can China’s carbon trading policy help achieve carbon neutrality? A study of policy effects from the five-sphere integrated plan perspective. J. Environ. Manag. 305, 114357. https://doi.org/10.1016/j.jenvman.2021.114357 (2022).
Chen, J. M. Carbon neutrality: Toward a sustainable future. Innovation 2, 100127–100127. https://doi.org/10.1016/j.xinn.2021.100127 (2021).
CO2 Daily. Latest daily CO2. https://www.co2.earth/daily-co2. Accessed 1 Jan 2022 (2022)
Sangomla, A. 2022 may Continue the Trend of the World’s Warmest Years: UK Met Office. https://www.downtoearth.org.in/news/global-temperature/2022-may-continue-the-trend-of-world-warmest-years-UK-met-office-81027. Accessed 8 Jan 2022 (2022).
Rabaey, K. & Ragauskas, A. J. Editorial overview: Energy biotechnology. Curr. Opin. Biotechnol. 27, v–vi. https://doi.org/10.1016/j.copbio.2014.04.001 (2014).
Mora, C. et al. Broad threat to humanity from cumulative climate hazards intensified by greenhouse gas emissions. Nat. Clim. Change 8, 1062–1071. https://doi.org/10.1038/s41558-018-0315-6 (2018).
Yang, M., Chen, L., Msigwa, G., Tang, K. H. D. & Yap, P.-S. Implications of COVID-19 on global environmental pollution and carbon emissions with strategies for sustainability in the COVID-19 era. Sci. Total Environ. 809, 151657. https://doi.org/10.1016/j.scitotenv.2021.151657 (2022).
Nigerian National Petroleum Corporation, NNPC. The Global Drive for Renewable Energy. http://www.nnpcgroup.com/publicrelations/oilandgasstatistics/.../monthlypetroleum.aspx. [accessed 23.06.17] (2017).
Osman, A. I. et al. Bioethanol and biodiesel: Bibliometric mapping, policies and future needs. Renew. Sustain. Energy Rev. https://doi.org/10.1016/j.rser.2021.111677 (2021).
Lassmann, T., Kravanja, P. & Friedl, A. Simulation of the downstream processing in the ethanol production from lignocellulosic biomass with Aspen Plus and IPSEpro. Sustain. Soc. https://doi.org/10.1186/s13705-014-0027-3 (2014).
Martinez-Hernandez, E. et al. Environmental Sustainability Analysis of UK Whole-Wheat Bioethanol and CHP Systems (University of Manchester, 2013).
Sánchez, O. J. & Cardona, C. A. Trends in biotechnological production of fuel ethanol from different feedstocks. Bioresour. Technol. 99, 5270–5295 (2008).
United States Department of Agriculture (USDA). The Economic Feasibility of Ethanol Production from Sugar in the United States. Available at: http://www.usda.gov/oce/reports/energy/EthanolSugarFeasibilityReport3.pdf (2013).
Sree, N. K., Sridhar, M., Suresh, K. & Rao, L. U. High alcohol production by solid substrate fermentation from starch substrates using thermotolerant Saccharomyces cerevisiae. Bioprocess. Eng. 20, 561–563 (2009).
NREL. Development of an ASPEN PLUS Physical Property Database for Biofuels Components. NREL, Golden, CO, Report MP-425-20685, April 2011. http://www.afdc.doe.gov/pdfs/3955.pdf (2011)
Kolusheva, T. A study of the optimal conditions for starch hydrolysis through thermostable α-Amylase. In Marinova Journal of the University of Chemical Technology and Metallurgy (Vol. 42, Issue 1) (2007).
Balat, M., Balat, H. & Oz, C. Progress in bioethanol processing. Prog. Energy Combust. Sci. 34, 551–573 (2008).
Misau, I. M., Bugaje, I. M., Mohammed, J., Mohammed, I. A., Diyau’deen, B. H. Production of bio-ethanol rom sugarcane: A pilot scale study in Nigeria. Int. J. Eng. Res. Appl. (IJERA). 2(4), 1142–1151. ISSN: 2248-9622 www.ijera.com (2012).
Marina, O. D. et al. Improving Bioethanol Production from Sugarcane: Evaluation of Distillation, Thermal Integration and Cogeneration Systems (School of Chemical Engineering, University of Campinas, 2010).
Aden, A., Ruth, M. & Iechura, J. Lignocellulosic Biomass to Ethanol Process Design and Economics Utilising Co-current Dilute Acid Prehydrolysis and Enzymatic Hydrolysis for Corn Stover (National Renewable Energy Laboratory-NREL, Report TP510-32438) (2002).
Sinnott, R. K., Coulson, J. M. & Richardson, J. F. Coulson and Richardson’s Chemical Engineering Vol. 6 (Elsevier Butterworth-Heinemann, 2005).
Chemical Engineering Plant Cost Index (CEPCI). Chemical Engineering. November 2016 (2016).
Central Bank of Nigeria: Money and Credit Statistics. Central Bank of Nigeria: Money and Credit Statistics. Retrieved October 10, 2022, from https://www.cbn.gov.ng/rates/mnymktind.asp (2022).
National Bureau of Statistics. Annual Abstract Statistics Volume 1.cdr—National Bureau. www.nigerianstat.gov.ng/.../annual%20abstract%20statistics%20volume1.aspx [Accessed 11.03.16] (2016).
Matches’ Aggglomerator Cost - Cone, Disk and Drum. Retrieved October 7, 2022, from https://www.matche.com/equipcost/Agglomerator.html (2022).
Jiang, G. et al. Manure and mineral fertilizer effects on crop yield and soil carbon sequestration: A meta-analysis and modeling across China. Glob. Biogeochem. Cycles 32(11), 1659–1672. https://doi.org/10.1029/2018GB005960 (2018).
Querel, E., Gonzalis-Reguerel, B., and Perez-Benedito, J.l. (2013). A practical approach to energy and thermoeconomic analysis of industrial processes (1st edition, pp9-40.), London Heidelberg: Springer London Heidelberg, New York Dordrecht.
Tongwane, M. et al. Greenhouse gas emissions from different crop production and management practices in South Africa. Environ. Dev. 9(2016), 23–35 (2016).
Wang, L., Littlewood, J. & Murphy, R. J. Environmental Sustainability of Bioethanol Production from Wheat Straw in the UK. Centre for Environmental Policy, Imperial College London, London SW7 2AZ, UK. http://www.matche.com/equipcost/Default.html. [Accessed 13.7.2016] (2013).
Gabrielle, B. & Gagnaire, N. Life-cycle assessment of straw use in bio-ethanol production: a case study based on biophysical modelling. Biomass Bioenergy 32, 431–441 (2008).
Nguyen, T. L. T., Gheewala, S. H. & Garivait, S. Energy balance and GHG-abatement cost of cassava utilisation for fuel ethanol in Thailand. Energy Policy 35(9), 4585–4596 (2007).
Suleiman, B., Olawale, A. S., Waziri, S. M. Exergetic-Economic Assessment of Bioethanol Refining Configurations. MSc. Thesis, Department of Chemical Engineering, Ahmadu Bello University, Zaria, Nigeria (2014).
Peters, M. S. & Timmerhaus, K. D. Plant Design and Economics for Chemical Engineers 4th edn. (McGraw-Hill, Inc, 2003).
FAOSTAT, Food and Agricultural Organization Organisation of the United Nations. (Accessed 10 December 2016) (2013).
Ogundipe, O. Price of 1 ton of Cassava in Nigeria. Premium Times. Retrieve from https://www.wealthresult.com/question/price-of-1ton-of-cassava-in-nigeria-and-companies-that-buy [Accessed 5.5.2018] (2017).
Famine early warning system (FEWS). Nigeria-Special News. Retrieved from www.fews.net/nigeria/special-report/december-13-2016 (2016).
Ibrahim, M. G., Abubakar, I. A., Isma’il, Y., Jiddah, A.M. & Bilkisu T. S. Prices of foodstuffs in Kano. Daily Trust News; September, 22. Retrieved from https://www.dailytrust.com.ng/harvest-prices-of-foodstuffs-in-kano.html (2017).
Fancelli, A. L. & Neto, D. D.. Produção de milho. 2. ed. Guaíba, Agropecuária, Brazil. 360 pp (2006).
Buah, S. S. & Mwinkaara, S. Response of sorghum to nitrogen fertilizer and plant density in Guinea Savannah zone. J. Agron. 8, 124–130 (2009).
Alliance for Jobs and Clean Energy. Fund the Solutions, Price the Pollution. Updated: November 2016 (2016).
Clean energy for all Europeans package. Retrieved October 8, 2022, from https://energy.ec.europa.eu/topics/energy-strategy/clean-energy-all-europeans-package_en (n.d.).
Author information
Authors and Affiliations
Contributions
A.S. wrote the manuscript and carried out the simulations and sustainability assessments as well as a discussion of the results. A.S.O. and Y.M.S. suggested the applicable software, provided some input data, and proofread the manuscript. S.K. assisted in the LCA results interpretations and standard error minimisation.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sanni, A., Olawale, A.S., Sani, Y.M. et al. Sustainability analysis of bioethanol production from grain and tuber starchy feedstocks. Sci Rep 12, 20971 (2022). https://doi.org/10.1038/s41598-022-24854-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-022-24854-7
- Springer Nature Limited