Abstract
Suppression of the crosstalk between adjacent waveguides is important yet challenging in the development of compact and dense photonic integrated circuits (PICs). During the past few years, a few of excellent approaches have been proposed to achieve this goal. Here, we propose a novel strategy by introducing nonuniform subwavelength strips between adjacent waveguides. In order to determine the widths and positions of nonuniform subwavelength strips, the particle swarm optimization (PSO) algorithm is utilized. Numerical results demonstrate that the coupling length between adjacent waveguides is increased by three (five) orders of magnitude in comparison with the case of uniform (no) subwavelength strips. Our method greatly reduces crosstalk and is expected to achieve a highly compact integrated density of PICs.
Similar content being viewed by others
Introduction
Over the past decades, much attention has been paid on the development of silicon photonics because of its compatibility with complementary metal oxide semiconductor (CMOS) technology1,2. Along with its further development, more and more waveguide elements need to be integrated on the silicon-on-insulator (SOI) platform3. Though various optical elements have been studied so far, such as transceivers, couplers/inverse taper, subwavelength gratings, multiplexers and so on4,5,6,7,8,9, the packing density of photonic integrated circuits (PICs) is still not as high as their electronic counterparts10. The reason is that the diffraction limit hinders the further shrinking of waveguide11.
During the past few years, great efforts have been paid to improve the integration density of PICs. One intuitive method is the use of plasmonic waveguides or metal-dielectric hybrid structures that can overcome the diffraction limit to further shrink the device footprint12,13,14. However, the large ohmic losses in metal limit its application in PICs. Alternatively, if we can effectively reduce the crosstalk between adjacent waveguide components, the minimum spacing will be greatly decreased and the packing density increased correspondingly. Recently, waveguide super-lattices15,16 and nanophotonic cloaking17 have been proposed to reduce crosstalk. The fundamental results show that negligible crosstalk can be obtained at telecommunication wavelengths.
Recently, subwavelength silicon gratings have been brought into optical waveguide and on-chip architectures to provide new degrees of freedom to control the guided wave in PICs18,19,20,21. As a consequence, the past few years have witnessed the emergence of a couple of compact waveguide devices including polarization/wavelength splitter22, polarization/mode converters/rotators23,24 and ultra-sharp waveguide bends25, integrated photonic switches26. Besides harnessing the guided wave, recent theoretical investigations show that subwavelength silicon gratings can be also utilized for evanescent wave manipulation27. Interestingly, the anisotropic gratings strips possess low effective index in direction normal to the gratings for total internal reflection in the core waveguide. Simultaneously, the anisotropic silicon gratings exhibit high index in the direction parallel to the interface for rapid decay of evanescent waves leaked from the core waveguide. Following this principle, Amin Khavasi et al. introduced two subwavelength strips between two neighboring waveguides18. Experimental results indicated that all-dielectric metamaterials can achieve a highly constrained mode and the coupling length is increased by ten times compared to the case without subwavelength strips. Yu et al. subsequently carried comprehensive studies regarding the effect of different geometries and their physical dimensions on the performance of crosstalk reduction28. With the same waveguide sizes, they increased the coupling length by two orders of magnitude when more than three silicon strips are placed between two adjacent waveguides.
It should be noted that all of the aforementioned works are based on uniform subwavelength gratings/strips, which can be taken as a homogenous material in the macroscopic picture. It is intuitive to know that a nonuniform structure possesses more design freedom than a uniform counterpart29. Bian considered uniform strips and the obvious question, inspired by other work in photonic optimization30,31,32,33,34,35,36,37,38, a computationally-optimized nonuniform design could be even better.
Results
Figure 1(a,b) show the proposed configuration that incorporates several subwavelength silicon strips lying in-between two adjacent single-mode SOI waveguides. The width, height, and edge to edge separation of the core waveguides are set to be 500 nm, 220 nm and 500 nm, respectively. Since the separation between single-mode SOI waveguides is only 500 nm (~λ/3), strong evanescent waves coupling between them will occur, accompanied by strong crosstalk and catenary shaped field39 (a hyperbolic consine function). Therefore, the motivation of this paper is to effectively suppress crosstalk by introducing nonuniform subwavelength structures (three subwavelength strips are utilized here as a representative example) between two neighboring waveguides. Since strong evanescent waves coupling or crosstalk will result in a short coupling distance, a useful measure of crosstalk strength is characterized by the coupling distance, which can be taken as the figure of merit (FOM) of the optimization design.
Simulation model and mode field distribution. (a) The proposed configuration that comprises a nonuniform silicon strip array inserted between the silicon waveguide pair. The substrate and cladding are silica and air, respectively. The width and height of two identical silicon ridge waveguides are 500 nm and 220 nm, respectively. (b) An enlarged view of the structure. The widths of three strips are w1, w2, w3, respectively. The widths of four gaps are g1, g2, g3, g4 respectively. (c) The electric field distribution of the waveguide cross section is plotted in log scale.
Intrinsically, the crosstalk is a consequence of the interaction between the modes in two adjacent waveguides. In this circumstance, the coupling between the original mode in each guide gives rise to two new supermodes that are simultaneously supported by two strong coupled waveguides, i.e., one symmetric (even) supermode and one antisymmetric (odd) supermode with the propagation constants denoted as β+ and β−, respectively. The coupling length Lc is defined as the distance over which a π phase difference accumulates between the two modes40, and thus can be expressed as:
Substituting the relationship between propagation constants is related to the mode effective index i.e., β+ = 2πne/λ and β− = 2πno/λ into Eq. (1), we can arrive at:
where ne and no are the real parts of the mode indexes for the even and odd modes, respectively (see Supplementary Fig. S1 for details). According to Eq. (2), when the mode index difference between them is infinitely small, the coupling distance will become infinitely large. Therefore, the key of the design is finding proper nonuniform subwavelength structures geometries to make the mode index difference as small as possible. Although one can obtain a rough estimate of the mode refractive index based on effective material theory when the waveguide dimensions are larger than the wavelength of light, it is not practical when the waveguide dimensions fall in the subwavelength scale41. The proposed silicon waveguide structures were investigated numerically by solving Maxwell’s equations on a cross-sectional mesh of the waveguide using the eigenmode solver of the finite difference eigenmode method (FDE) based software MODE solutions. The core of the FDE method is that Maxwell’s equations are formulated into a matrix eigenvalue problem after meshing the waveguide geometry by using the finite difference algorithm, and then, to obtain the effective index and mode profiles of the waveguide modes by using sparse matrix techniques (Lumerical Inc.)42.
Since the mode index is highly sensitive to the geometries, separation distance, and ambient conditions, the introduction of several nonuniform subwavelength structures between the two coupled waveguides gives rise to a nontrivial design space for decreasing the crosstalk. Since it is inefficient to find an excellent design by full parameters sweeping, we alternatively resort to optimization algorithms in our design. Among various optimization algorithms, particle swarm optimization (PSO) has been widely used in the optimization of a myriad of optical waveguide devices, e.g., waveguide crossing43, optical phased arrays44, compact silicon grating coupler45. Initially, several simulations with different coefficients were performed using the standard PSO (SPSO) setup, and the results were always fluid. The desired coupling length was mainly varying between 107~108 μm and sometimes greater than 108 μm which meant that the program might be stuck in the local optimum. In order to tackle this problem, the computationally-optimized method is adopted here. Fortunately, the commercial software MODE Solutions has provided an application programming interface (API) to the MATLAB so that we can run MODE Solutions with matlab. Among them, the MODE Solutions provides a comprehensive optical waveguide design environment, in which FDE solvers could be used to calculate the effective index precisely. The improved PSO algorithm for avoiding local optimization is implemented by MATLAB software. A flow diagram of the simulation for the optimization process is shown in Fig. 2.
The simulation includes two significant processes: one is the data exchange between MATLAB and MODE, and another is the iterative operation of optimization algorithm in MATLAB. Firstly, a set of widths and gaps are randomly generated in MATLAB within the specified range, which is transferred to MODE by using API to generate subwavelength structure models with different widths and separations. The mode effective index which is calculated by using the FDE solver is passed back to MATLAB for calculating coupling length. The maximum coupling length and the width information of its corresponding subwavelength structure are stored. Next, we move on to the second part. The population of each iteration consists of 30 particles. The currently obtained coupling length, widths and gaps generated in each iteration step are compared with the previous best results, and the maximum coupling length as well as corresponding widths and gaps are updated each time. The performance of SPSO is affected by changing the values of its coefficients. Inspired by an adaptive approach46, a dynamic maximum flight speed and an inertia weight are chosen by selecting the appropriate range. The inertia weight provides a restriction in position jump: low values allow particles to roam around the target positions, while high values provide a large movement orientated to target. Maximum flight speed determines how far the particles in PSO can fly. Initially, the inertia weight and maximum flight speed are set to be 0.6 and 0.05, respectively. To a certain extent, keeping the dynamic change of speed within the specified range can avoid falling into local optimization. Dynamic flight speed is applied to update the position. Here, we set two sets of the inertia weight (0.55~0.65 under the threshold 1 and 0.65~0.75 under the threshold 2) and flight speed (0.005~0.01 under the threshold 1 and 0.01~0.05 under the threshold 2) according to the requirements of two different thresholds. In the initial attempt, we find that it is difficult to make a change once the coupling length exceeds 10 m. Therefore, in order to avoid falling into local optimization, we use the “jump long distance, search small distance” approach to improve the PSO algorithm. And two threshold values (threshold 1 is 107 μm and threshold 2 is 108 μm) are set in advance for judgment. Specifically, when the coupling length reaches the threshold value 1 and maintains no change for a certain amount of generations, a slightly larger inertia weight and a flight speed (inertia weight: 0.65~0.75, flight speed: 0.01~0.05) are utilized to endow a new position to the parameters of swarms, and subsequently, a small range of iterative search (inertia weight: 0.55~0.65, flight speed: 0.005~0.01) is performed. If the results remain the same after a certain number of iterations (such as, ten generations), a large range of jumps is applied again and the circle continues until the coupling length exceeds threshold value 2 or the maximum number of iterations is reached.
In order to verify our proposal, different aspects are presented in the following. The first design is a pair of Si ridge waveguides with an edge-to-edge separation of 500 nm, with three subwavelength strips in between to reduce crosstalk. The second design is similar to the first one but with an edge-to-edge separation of 450 nm. Meanwhile, the electric field intensity distributions of both cases are plotted so as to see the coupling process in a more intuitive way.
Uniform subwavelength strips (e.g. one strip, two and three strips with the same width and separation) are first investigated to compare with the results of the ref. 28. The results shown in Fig. 3(a–c) indicate that a good agreement between them is found and the small discrepancy is caused by different software, demonstrating our convergence test is justification (see Supplementary Table S1). Next, we take three strips as example to explore the influence of the introduction of subwavelength structures on suppressing crosstalk. Figure 3(d) shows the FOM varies with the number of iterations, where the coupling length is calculated according to the theoretical formula shown in Eq. (2), with the effective indexes obtained by using the FDE solver. After more than 100 iterations, the coupling length reaches 312.2 m, three orders of magnitude improvement than the result obtained in the ref. 28. The results demonstrated that the proposed strategy of introducing nonuniform subwavelength strips can be used as a promising candidate in suppressing crosstalk between two neighboring waveguides. The optimization widths of gaps and strips (g1, w1, g2, w2, g3, w3, g4) are 77 nm, 72 nm, 58 nm, 86 nm, 58 nm, 72 nm, 77 nm, respectively. It should be noted that the optimization design can be fabricated by advanced 193 nm immersion lithography technology with an achieved feature size down to 50 nm47. The analysis of the fabrication imperfection of our proposed structures and its sensitivity to wavelength are also studied (see Supplementary Fig. S2).
In order to study the influence of the introduction of nonuniform subwavelength strips on the crosstalk between waveguides in Fig. 1, the electric field intensity distribution along the propagation direction was examined. The acquisition of electric field intensity distribution is divided into two steps. The first step is to calculate the field distribution along the propagation direction for both supermodes (even mode and odd mode) through a “propagate” command packaged by the software or FDE solver, and the second step is to accumulate these field distributions to obtain the total propagation field. The concrete implementation is achieved through scripts. It can be seen from Fig. 4(a,b) that the fundamental mode can be transmitted forward for more than 100 m without crosstalk occurring, which is superior to the result previously reported28. The coupling length obtained from Fig. 4(c) agrees well with the result we get in Fig. 3(d). Multiple coupling processes occur when the propagation length is far enough, as shown in Fig. 4(d).
The electric field intensity distribution versus y and L. (a) Electric field intensity distribution with a propagation length of 10 m. No coupling occurs between two waveguides. (b) Electric field intensity distribution with a propagation length of 100 m, where coupling is going to happen. (c) Electric field intensity distribution with a propagation length of 500 m. It could be seen that a complete coupling process is generated between two waveguides. (d) Electric field intensity distribution with propagation length of 2000 m.
Further research shows that the proposed crosstalk suppressing method can work well for smaller waveguide spacing, as shown in Fig. 5(a). We give a schematic that two silicon ridge waveguides are separated from each other with an edge to edge distance of 450 nm, achieving the coupling length of 2.167 m. Figure 5(b) indicates that strong confinement occurs in the ridge waveguide. The simulation result can be obtained from Fig. 5(c,d), which is close to the theory result in Fig. 5(e). Different from the previous setting, we set the inner mesh size to be 500 nm, i.e. an expansion of 25 nm on each side. The optimization widths of gaps and strips (g1, w1, g2, w2, g3, w3, g4) are 52 nm, 60 nm, 57 nm, 112 nm, 57 nm, 60 nm, 52 nm, respectively. Furthermore, smaller waveguide spacings are tested. (See Supplementary Fig. S3 for detail).
Simulation results of evanescent coupling waveguides with a separation gap of 450 nm. (a) Schematic diagram of structure with a separation gap of 450 nm. (b) Mode intensity distribution in waveguide cross section. (c,d) Distribution of light fields with different propagation lengths. (e) The optimization progress for evanescent coupling waveguide with a separation gap of 450 nm.
Even if the edge to edge separation of waveguides is set to be 300 nm, the coupling length can still reach 1000 μm. Although the coupling distance can be further improved by adopting better optimized algorithm and more complex structures with stronger anisotropy, the increase in coupling length seems to have approached to an upper limit owing to the limitations of available materials and fabrication resolution. Furthermore, evanescent waves cannot be completely eliminated, even if they decay sharply between waveguides, according to the theory of Jahani et al. This means that crosstalk must occur between two parallel waveguides, indicating that the coupling length is also limited, but may not be the value we found. As the figure shown above, as the distance between two waveguides becomes smaller, the coupling length decreases. Though unavoidably, our method can still promote the development of silicon photonics in terms of integration and miniaturization due to the effect of great crosstalk suppression.
Discussions
In this paper, we introduce nonuniform subwavelength strip arrays between integrated optical waveguides. Compared with a pair of waveguides with introducing uniform strip arrays, the coupling length is improved by three orders of magnitude, and it is five orders of magnitude greater than the case without strip arrays. It is shown that crosstalk is also suppressed well for waveguides with even smaller spacing, e.g., 450 nm, 400 nm, 350 nm and 300 nm. Though we have to compromise the coupling length and spacing, further reduction in spacing with good coupling length is expected in the future. The introduction of nonuniform strips is expected to realize more intensive photonic integration platform. The reduction of crosstalk is beneficial for the further development of on-chip spectrometer48, automatic cars49, and other applications50.
References
Chrostowski, L. & Hochberg, M. Silicon photonics design: from devices to systems (Cambridge University, 2015).
Soref, R. The Past, Present, and Future of Silicon Photonics. IEEE J. Sel. Top. Quant. 12, 1678–1687 (2006).
Jalali, B. & Fathpour, S. Silicon Photonics. J. Lightwave Technol. 24, 4600–4615 (2006).
Tanaka, Y. Recent Progress in the Development of Large-Capacity Integrated Silicon Photonics Transceivers. IEICE T. Electron. E102.C, 357–363 (2019).
Shen, Y. et al. Silicon Photonics for Extreme Scale Systems. J. Lightwave Technol. 37, 245–259 (2019).
Cerutti, I., Andriolli, N. & Velha, P. Engineering of closely packed silicon-on-isolator waveguide arrays for mode division multiplexing applications. J. Opt. Soc. Am. B 34, 497–506 (2017).
Marchetti, R., Lacava, C., Carroll, L., Gradkowski, K. & Minzioni, P. Coupling strategies for silicon photonics integrated chips. Photon. Res. 7, 201–239 (2019).
Zhou, W. et al. Subwavelength Engineering in Silicon Photonic Devices. IEEE J. Sel. Top. Quant. 25, 1–13 (2019).
Giewont, K. et al. 300-mm Monolithic Silicon Photonics Foundry. Technology. IEEE J. Sel. Top. Quant. 25, 1–11 (2019).
Arakawa, Y., Nakamura, T., Urino, Y. & Fujita, T. Silicon photonics for next generation system integration platform. IEEE Commun. Mag. 51, 72–77 (2013).
Jahani, S. & Jacob, Z. Transformed cladding waveguides: Confining light with all-dielectric metamaterials. CLEO’ 2013, 1–2 (2013).
Gramotnev, D. K. & Bozhevolnyi, S. I. Plasmonics beyond the diffraction limit. Nature Photon. 4, 83 (2010).
Dionne, J. A., Sweatlock, L. A., Atwater, H. A. & Polman, A. Plasmon slot waveguides: Towards chip-scale propagation with subwavelength-scale localization. Phys. Rev. B 73, 035407 (2006).
Guo, Y. et al. Chip-Integrated Geometric Metasurface As a Novel Platform for Directional Coupling and Polarization Sorting by Spin–Orbit Interaction. IEEE J. Sel. Topics Quantum Electron. 24, 4700107 (2018).
Gatdula, R., Abbaslou, S., Lu, M., Stein, A. & Jiang, W. Guiding light in bent waveguide superlattices with low crosstalk. Optica 6, 585–591 (2019).
Song, W. et al. High-density waveguide superlattices with low crosstalk. Nat. Commun. 6, 7027 (2015).
Shen, B., Polson, R. & Menon, R. Increasing the density of passive photonic-integrated circuits via nanophotonic cloaking. Nat. Commun. 7, 13126 (2016).
Khavasi, A., Chrostowski, L., Lu, Z. & Bojko, R. Significant Crosstalk Reduction Using All-Dielectric CMOS-Compatible Metamaterials. IEEE Photonics Tech. L. 28, 2787–2790 (2016).
Cheben, P., Halir, R., Schmid, J. H., Atwater, H. A. & Smith, D. R. Subwavelength integrated photonics. Nature 560, 565–572 (2018).
Li, Y. et al. On-chip zero-index metamaterials. Nature Photon. 9, 738–742 (2015).
Luo, X. Engineering Optics 2.0: A Revolution in Optical Theories, Materials, Devices and Systems (Springer Singapore, 2019).
Shen, B., Wang, P., Polson, R. & Menon, R. An integrated-nanophotonics polarization beamsplitter with 2.4 × 2.4 μm2 footprint. Nature Photon. 9, 378–382 (2015).
Wang, H. et al. Compact Silicon Waveguide Mode Converter Employing Dielectric Metasurface Structure. Adv. Opt. Mater. 7, 1801191 (2019).
Ohana, D., Desiatov, B., Mazurski, N. & Levy, U. Dielectric Metasurface as a Platform for Spatial Mode Conversion in Nanoscale Waveguides. Nano Lett. 16, 7956–7961 (2016).
Wu, H. et al. Ultra-Sharp Multimode Waveguide Bends with Subwavelength Gratings. Laser & Photonics Rev. 13, 1800119 (2019).
Wu, C. et al. Low-Loss Integrated Photonic Switch Using Subwavelength Patterned Phase Change Material. ACS Photonics 6, 87–92 (2019).
Jahani, S. & Jacob, Z. Transparent subdiffraction optics: nanoscale light confinement without metal. Optica 1, 96–100 (2014).
Bian, Y. et al. Efficient Cross-talk Reduction of Nanophotonic Circuits Enabled by Fabrication Friendly Periodic Silicon Strip Arrays. Sci. Rep. 7, 15827 (2017).
Wang, L. et al. Design of a low-crosstalk half-wavelength pitch nano-structured silicon waveguide array. Opt. Lett. 44, 3266–3269 (2019).
Pu, M. et al. Catenary optics for achromatic generation of perfect optical angular momentum. Sci. Adv. 1, e1500396 (2015).
Lin, D., Fan, P., Hasman, E. & Brongersma, M. L. Dielectric gradient metasurface optical elements. Science 345, 298 (2014).
Guo, Y. et al. Merging geometric phase and plasmon retardation phase in continuously shaped metasurfaces for arbitrary orbital angular momentum generation. ACS Photonics 3, 2022–2029 (2016).
Verslegers, L. Planar lenses based on nanoscale slit arrays in a metallic film. Nano Lett. 9, 235–238 (2009).
Guo, Y., et al. High‐efficiency and wide‐angle beam steering based on catenary optical fields in ultrathin metalens. Adv. Opt. Mater. 6,1800592 (2018).
Guo, Y., et al. Spoof plasmonic metasurfaces with catenary dispersion for two-dimensional wide-angle focusing and imaging. iScience 21, 145–156 (2019).
Li, X. et al. Multicolor 3D meta-holography by broadband plasmonic modulation. Sci. Adv. 2, e1601102 (2016).
Yu, N. et al. Light Propagation with Phase Discontinuities: Generalized Laws of Reflection and Refraction. Science 334, 333 (2011).
Luo, X. Principles of electromagnetic waves in metasurfaces. Sci. China: Phys., Mech. Astron 58, 594201 (2015).
Luo, X. Catenary Optics (Springer Singapore, 2019).
White, T. P. Theory of resonance and mode coupling in photonic crystal devices (PhD Thesis University of Sydney, 2005).
Eggleton, B. J., Poulton, C. G., Rakich, P. T., Steel, M. J. & Bahl, G. Brillouin integrated photonics. Nature Photon. (2019).
Lin, X. et al. FDTD method and models in optical education. In Proc. SPIE 10452, ETOP 2017 104524J (2017).
Han, H.-L. et al. High performance ultra-compact SOI waveguide crossing. Opt. Express 26, 25602–25610 (2018).
Komljenovic, T. & Pintus, P. On-chip calibration and control of optical phased arrays. Opt. Express 26, 3199–3210 (2018).
Asaduzzaman, M., Bakaul, M., Skafidas, E. & Khandokar, M. R. H. A compact silicon grating coupler based on hollow tapered spot-size converter. Sci. Rep. 8, 2540 (2018).
Nickabadi, A., Ebadzadeh, M. M. & Safabakhsh, R. A novel particle swarm optimization algorithm with adaptive inertia weight. Applied Soft Computing 11, 3658–3670 (2011).
Selvaraja, S. K. et al. 193 nm immersion lithography for high-performance silicon photonic circuits. In Proc. SPIE 9052, Optical Microlithography XXVII (eds Lai, K. & Erdmann, A.) 90520F (2014).
Ma, K., Chen, K., Zhu, N., Liu, L. & He, S. High-resolution compact on-chip spectrometer based on an echelle grating with densely packed waveguide array. IEEE Photonics J. 11, 1–7 (2019).
Xie, W. et al. Heterogeneous silicon photonics sensing for autonomous cars. Opt. Express 27, 3642–3663 (2019).
Krainak, M. et al. Integrated photonics for NASA applications. In Proc SPIE 10899, Components and Packaging for Laser Systems V 108990F (2019).
Acknowledgements
The work was supported by the National Natural Science Foundation of China (61875253, 61575201, 61622508).
Author information
Authors and Affiliations
Contributions
Y.H.G. conceived the original idea, Y.Y., Y.H.G. M.B.P. establish the model and do the numerical simulations, Y.Y., Y.H.G., and Y.J.H. wrote the manuscript. X.G.L. supervised the project. All the authors have analyzed and discussed the results thoroughly.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Yang, Y., Guo, Y., Huang, Y. et al. Crosstalk reduction of integrated optical waveguides with nonuniform subwavelength silicon strips. Sci Rep 10, 4491 (2020). https://doi.org/10.1038/s41598-020-61149-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-020-61149-1
- Springer Nature Limited
This article is cited by
-
Bolstering functionality in multilayer and bilayer WS2 via focused laser micro-engraving
Science China Information Sciences (2023)