Abstract
Aqueous Two-Phase Extraction is known to be a gentle separation technique for biochemical molecules where product partitioning is fast. However, the reason for the high mass transfer rates has not been investigated, yet. Many researchers claim that the low interfacial tension facilitates the formation of very small droplets and with it a large interfacial area causing a fast partitioning. However, an experimental evidence for this hypothesis has not been published yet. In this study, the mass transfer coefficients of two proteins, namely lysozyme and bromelain, were determined by providing a defined interfacial area for partitioning. Compared to low molecular weight solutes the mass transfer coefficient for the proteins investigated was small proving for the first time that the large interfacial area and not fast diffusion seems to be the reason for fast protein partitioning.
Similar content being viewed by others
Introduction
Aqueous Two-Phase Extraction (APTE) has been successfully applied as gentle unit operation for the purification of biomolecules such as therapeutic proteins1,2,3, enzymes4 and antibiotics5,6. Aqueous Two-Phase Systems (ATPSs) are known for fast product partitioning7, however, the reason for these high mass transfer rates has not been investigated so far. According to the kinetic two film model the rate of interphase mass transfer depends on the interfacial area as contact area between two liquid phases, the mass transfer coefficient, which is a measure of the specific mass transport rate across the interface, and the concentration difference, that is the driving force8. Cunha et al. briefly summarize, what Albertsson9, Husted et al.10 and Fauquex et al.11 already explained: “The fast approach to equilibrium is owing to the low interfacial tension between the two phases, which enables the formation of very small droplets and thus a large interface for mass transfer with low energy input”12. This assumption is shared by many researchers12,13,14,15,16,17,18,19. Although, the hypothesis is used over years, its evidence has not been proven so far.
In this study, the mass transfer coefficients of two macromolecules in an ATPS were determined by keeping the interfacial area constant during partitioning. That was realized by using a so-called Nitsch-Cell. This type of cell, first introduced by Lewis20, provides a known fixed interfacial area. The relatively simple set-up offers one of the most efficient methods to determine the mass transfer coefficient8. By determining the mass transfer coefficient and comparing it to values of other systems one can decide, whether the mass transfer is high due to a high mass transfer coefficient or due to the ability of the ATPS to be easily and efficiently dispersed generating a large interface.
Results
Concentration profiles of lysozyme and bromelain in the PEG and citrate phase were measured against time. The profiles for lysozyme in a PEG4000/citrate ATPS with 2 wt.-% NaCl are illustrated in Fig. 1. From the experiments it can be seen that the system reached equilibrium after about 1,020 min. For bromelain the equilibrium was reached after 1,080 min (see Supplementary Fig. S1). The mass balance was closed with an average accuracy of 2% for both systems.
From the slope of the logarithmic profile of \(\mathrm{ln}\,\frac{({c}_{j,\infty }-{c}_{j,0})}{({c}_{j,\infty }-{c}_{j})}\cdot \frac{{V}_{j}}{{a}_{cell}}\) plotted against time the PEG mass transfer coefficients were obtained as shown in Fig. 2. The time interval for the determination of k for both proteins was set to 720 min. The non-linear behaviour for bromelain in the beginning of the logarithmic profile might be a result of mixing the phases during the filling of the Nitsch-Cell. For lysozyme a PEG k -value of 3.79 × 10−6 m s−1 and for bromelain a PEG k -value of 3.44 × 10−6 m s−1 were determined by least square minimization. Mass transfer coefficients were plotted for the PEG phases only as the citrate k –value of lysozyme with 3.72 × 10−6 m s−1 was equal to the PEG one, which should be true for bromelain as well, once the mass balance is fulfilled.
Discussion
Comparing the results with experiments obtained by Kruber et al. where the transfer of hexan between heptane and methanol was determined in the same Nitsch-Cell used here, the equilibrium was reached faster (approx. 60 min) and the k -value of 6.26 × 10−5 m s−1 21 was 17–18 times higher than the ones measured in this study. Assuming an ideal mixing in each part of the compartment in the Nitsch-Cell, mass transfer is controlled by diffusion. As the mass transfer coefficient is related to the film thickness that is generally affected by the mixing conditions, higher stirrer speeds might lead to turbulent conditions and thus a thicker film. However, as the interface was stable due to the adjusted speed of the stirrer for the system in this study and for that examined by Kruber et al., it can be assumed that the significantly smaller mass transfer coefficients in this study cannot be related to the film thickness alone. The slower mass transfer obtained in this study might be influenced by the higher viscosity of the PEG phase, as with higher viscosity the diffusion coefficient decreases22. In addition, the molecular weight might affect the k -value, due to the increase in frictional resistance23. That is why further literature data was investigated: Kulaguin Chicaroux determined the concentration profile of the amino acid L-serine in a PEG8000/Dextran ATPS in the same Nitsch-Cell. The equilibrium was reached after approximately 300 min24. Comparing the value to the partitioning of lysozyme the equilibrium was reached approximately three times faster resulting in a k -value of 1.22 × 10−5 m s−1. Melgarejo-Torres measured for a cyclic ketone (MW = 108.14 g mol−1) with a similar molecular weight compared to L-serine (MW = 105.09 g mol−1) in a water ionic liquid biphasic system using a modified Lewis-Cell a k-value of 1.01 × 10−5 m s−1 25. After comparing the physicochemical properties of the ionic liquid used in the study of Melgarejo-Torres, they differ in the viscosity of the PEG phase and interfacial tension to that of the ATPSs used in this study and to that of the PEG8000/Dextran system. The kinematic viscosity in the PEG phase used for lysozyme is significantly higher with a value of 23.86 mm2 s−1, measured by a capillary viscometer according to Kaplanow et al.26, compared to that of the ionic liquid with 2.5 × 10−5 mm2 s−1 25. For the PEG8000/Dextran system the kinematic viscosity of the PEG phase is 8.6 mm2 s−1 and for the Dextran phase it is 44.9 mm2 s−1, both significantly higher in comparison to the water ionic liquid system27. Regarding the interfacial tension the one of the ionic liquid is with 7.5 mN m−1 about 60 times larger compared to the PEG/citrate ATPS without NaCl (0.125 mN m−1)26 and about 25 times larger compared to the same ATPS with exemplary 4 wt.-% NaCl (0.300 mN m−1). For the PEG8000/Dextran system a 125 times smaller interfacial tension of 0.060 mN m−1 was determined compared to the ionic liquid system28. Although the kinematic viscosity and the interfacial tension of the water ionic liquid system differs significantly to that of the PEG/Dextran system, the k -values determined were in the same range, as the molecular weight of the amino acid and the cyclic ketone were similar. However, for the PEG/citrate system the viscosity was approximately as high as for the PEG/Dextran APTS, but the molecular weight of lysozyme with 14.4 kDa29 is significantly higher compared to that of L-serine with 0.105 kDa. Thus, the small k -values for lysozyme and bromelain measured in the study were a result of a high molecular weight. Due to bromelain’s higher molecular weight of 21.4 kDa; measured via SDS-PAGE gel electrophoresis (own data), compared to lysozyme, it reached the equilibrium later than lysozyme. As the mass transfer in the Nitsch-Cell is controlled by diffusion only, the diffusion coefficients might give an explanation for the small mass transfer coefficients of macromolecules. Thereby, the diffusion coefficient is influenced by the solute size. The larger the molecular volume, the smaller the diffusion coefficient and the smaller the mass transfer coefficient.
The k -values for proteins investigated in this study are small. As the partitioning for proteins in an ATPS is fast, even at larger scale (30 L)14, the hypothesis seems to be true that the mass transfer is enhanced by generating large interfacial area only.
Conclusion
In this study, the mass transfer coefficients of lysozyme and bromelain were determined for a constant interfacial area utilising a Nitsch-Cell. As the mass transfer rates of the proteins were 17 times lower compared to values of an organic compound in an organic/organic system, the fast equilibrium obtained in an ATPS seems to be caused by the large interfacial area generated during mixing. After comparing the physicochemical parameters of polymer/salt ATPS to those of polymer/polymer and water ionic liquid systems and the mass transfer coefficients of high and low molecular weight solutes, the molecular size seems to be the dominating parameter affecting the mass transfer coefficient.
Materials and Methods
Materials
Polyethylene glycol (PEG) with an average molecular weight of 4000 g mol−1 was obtained from Merck KGaA (Germany). Tri-sodiumcitrate dihydrate (Na3C6H5O7 * 2 H2O, ≥99.0 wt.-%) was purchased from VWR Chemicals (Belgium). Citric acid (C6H8O7, ≥99.0 wt.-%) and sodium chloride (NaCl, ≥99.8 wt.-%) were obtained from Carl Roth GmbH & Co. KG (Germany). The proteins lysozyme (from chicken egg white; ≥90.0 wt.-%) and bromelain (from pineapples, ≥40.0 wt.-%) were purchased from Sigma-Aldrich Co. (Germany). Pure deionized water was received from a Milli-Q Synthesis apparatus with 0.22 μm Millipack express filters from EMD Millipore Corporation (USA) and was used for all solutions throughout this work.
Methods
Preparation of ATPS
For all ATPS, PEG with a molecular weight of 4000 g mol−1, citrate as second phase forming component and NaCl as displacement agent to control partitioning were solved in deionized water. The pH value of 5.6 was adjusted by adding Na3C6H5O7 * 2 H2O and C6H8O7 as citrate components in a mass ratio of 13.2. The systems were weighted to reach 12.5 wt.-% of each phase forming compound. For lysozyme and bromelain an ATPS with 2 wt.-% and 6 wt.-% of NaCl, respectively, was prepared. All ATPSs were equilibrated and settled in a tempered double-walled dropping funnel at a constant temperature of 298.15 K. The equilibrated phases were separated and solutions were prepared for lysozyme (Lys) and bromelain (Bro) by dissolving 0.1 gLys L−1 or 1 gBro L−1 in the equilibrated citrate phase of an ATPS with 2 or 6 wt.-% NaCl, respectively. All solutions were stored at 298.15 K prior the experiments.
Nitsch-Cell
A Nitsch-Cell30 consisting of a double-walled glass cylinder (I) with an internal diameter of 103.8 mm and a volume of 1.04 L was used to determine the mass transfer coefficients (Fig. 3). Two identical internal fittings consisting of a 28 mm flow tube (II) with an inner diameter of 72.5 mm and eight baffles (IV) with a height of 50 mm and integrated stirrer (VI) in both phases provided a convective flow from the interphase to the stirrer. To enable a stable interface with a constant area of 84.6 cm2, the stirrer speed was adjusted to keep the flow directions equal in both phases. Due to the higher viscosity in the PEG phase compared to the citrate phase, different agitation rates were adjusted. By stirring the PEG phase at 120 rpm and the citrate phase for 40 rpm a convective flow in each phase was provided and a stable interface was guaranteed. Silicone oil was used as heat transfer medium passing the double-walled jacket ensuring a constant temperature of 298.15 K. The experiments were performed as triplicates.
Mass transfer coefficient experiments
The Nitsch-Cell was equally filled with citrate and PEG phase volume. After filling the Nitsch-Cell with citrate phase, the PEG phase was added carefully to prevent any mixing. The stirrers were started first with small agitation rates of 30 rpm for the citrate and 50 rpm for the PEG phase. After a clear interface became visible, the agitation rates were increased to 40 rpm and 120 rpm, respectively. In regular intervals samples of the citrate and PEG phase were taken for analysis using syringes.
The two-film theory is based on Fick’s first law and can be used to describe the mass transfer through a binary interface. Thereby, the assumption is the existence of stationary films on the two sides of the interface that are responsible for all the resistance to mass transfer and the mass transfer in the laminar interface layer is controlled by molecular diffusion. At the interface a linear equilibrium relationship between the PEG and the citrate phase and no concentration gradients in the bulk phases are assumed. As the mass transfer is purely diffusive, the film thickness might have an impact on the mass transfer coefficient. Thereby, the film thickness is related to the hydrodynamic properties, which depend on the average velocity of the liquid, the geometry and the physical properties of the fluids.
The mass transfer through the liquid/liquid interface is expressed by equation (1) for the phase j (here either PEG or citrate phase)8:
where \(\frac{d{c}_{j}}{dt}\,\,\)is the mass transfer rate in the phase j, Vj is the compartment volume of the corresponding phase, kj is the mass transfer coefficient, \({a}_{cell}\) is the interfacial area, \({c}_{j,\infty }\) is the final concentration in the bulk phase j (here the concentration reached at equilibrium), and cj the concentration in the bulk phase j at time t. The equation (1) is applicable for the up taking side (here the PEG phase). The delivering side (here the citrate phase) has an opposite sign. Solving equation (1) at t = 0, cj = cj,o, where cj,o is the concentration in the beginning, results in equation (2):
By plotting \(\mathrm{ln}\,\frac{({c}_{j,\infty }-{c}_{j,0})}{({c}_{j,\infty }-{c}_{j})}\cdot \frac{{V}_{j}}{{a}_{cell}}\) against the time the mass transfer coefficient is equivalent to the slope of the curve.
Analysis
Determination of lysozyme concentration was performed via high performance liquid chromatography (HPLC) using a Nucleodur® C18EC column with a pore size of 300 Å and a particle size of 5 µm from Macherey-Nagel (Düren, Germany). The method described by Sutherland et al.31 was used with a modified gradient of the mobile phases (see Supplementary Table S1). The quantification of bromelain concentration was performed via UV absorption at 280 nm.
Data Availability
The data will be supplied upon request.
References
Guan, Y., Lilley, T. H., Treffry, T. E., Zhou, C.-L. & Wilkinson, P. B. Use of aqueous two-phase system in the purification of human interferon-alpha1 from recombinant Escherichia coli. Enzyme and Microbal Technology, 446–455 (1996).
Lin, Y. K., Ooi, C. W., Ramanan, R. N., Ariff, A. & Ling, T. C. Recovery of Human Interferon Alpha-2b from Recombinant Escherichia coli by Aqueous Two-Phase System. Separation Science and Technology 47, 1023–1030 (2012).
Muendges, J., Stark, I., Mohammad, S., Górak, A. & Zeiner, T. Single stage aqueous two-phase extraction for monoclonal antibody purification from cell supernatant. Fluid Phase Equilibria 385, 227–236 (2015).
Prinz, A., Hönig, J., Schüttmann, I., Zorn, H. & Zeiner, T. Separation and purification of laccases from two different fungi using aqueous two-phase extraction. Process Biochemistry 49, 335–346 (2014).
Mokhtarani, B., Karimzadeh, R., Amini, M. H. & Manesh, S. D. Partitioning of Ciprofloxacin in aqueous two-phase system of poly(ethylene glycol) and sodium sulphate. Biochemical Engineering Journal 38, 241–247 (2008).
Khederlou, K., Pazuki, G. R., Taghikhani, V., Vossoughi, M. & Ghotbi, C. Measurement and Modeling Process Partitioning of Cephalexin Antibiotic in Aqueous Two-Phase Systems Containing Poly(ethylene glycol) 4000, 10000 and K 2 HPO 4, Na 3 Citrate. Journal of Chemical & Engineering Data 54, 2239–2244 (2009).
Husted, H., Kroner, H., Menge, U. & Kula, M.-R. Protein recovery using two-phase systems. Trends in Biotechnology, 139–144 (1985).
Pratt, H. R. C. In Handbook of solvent extraction, edited by Lo, T. C., Braid, M. H. I. & Hanson, C. pp. 91–123 (Wiley, New York, 1983).
Albertsson, P. A. Partition of Cell Particles and Macromolecules. 3rd ed. (Wiley-Interscience, New York, 1986).
Husted, H., Kroner, K. H. & Kula, M.-R. In Partitioning in Aqueous Two-Phase Systems. Theory, Methods, Uses, and Applications to Biotechnology, edited by H. Walter, D. E. Brooks, D. Fischer, pp. 529–587 (Academic Press. Inc., Orlando, 1985).
Fauquex, P.-F., Husted, H. & Kula, M.-R. Phase equilibration in agitated vessels during extractive enzyme recovery. Journal of Chemical Technology & Biotechnology 1985, 51–59.
Cunha, T. & Aires-Barros, R. In Methods in Biotechnology, edited by Hatti-Kaul, R. (Humana Press Inc., Totowa, N. J.), pp. 391–409.
Bim, M. A. & Franco, T. T. Extraction in aqueous two-phase systems of alkaline xylanase Extraction in aqueous two-phase systems of alkaline xylanase produced by Bacillus pumilus and its application in kraft pulp bleaching. Journal of Chromatography B, 349–356 (2000).
Costa, M. J. L., Cunha, M. T., Cabral, J. M. S. & Aires-Barros, M. R. Scale-up of recombinant cutinase recovery by whole broth extraction with PEG-phosphate aqueous two-phase. Bioseparation, 231–238 (2000).
Glyk, A., Scheper, T. & Beutel, S. PEG–salt aqueous two-phase systems: an attractive and versatile liquid–liquid extraction technology for the downstream processing of proteins and enzymes. Applied Microbiology and Biotechnology 99, 6599–6616 (2015).
Rosa, P. A. J., Azevedo, A. M. & Aires-Barros, M. R. Application of central composite design to the optimisation of aqueous two-phase extraction of human antibodies. Journal of Chromatography A 1141, 50–60 (2007).
Kula, M.-R. & Selber, K. In Encyclopedia of bioprocess technology. Fermentation, biocatalysis, and bioseparation, edited by M. C. Flickinger & S. W. Drew, Vol. 4, pp. 2179–2191 (Wiley, New York, 2002).
Kalaivani, S. & Regupathi, I. Partitioning studies of α-lactalbumin in environmental friendly poly (ethylene glycol)—citrate salt aqueous two phase systems. Bioprocess and Biosystems Engineering 36, 1475–1483 (2013).
Balmelli, M., Steiner, L. & Hartland, S. Behaviour of turbulent dispersions in a stirred single-stage cell. Chemical Engineering Science, 1653–1660 (2000).
Lewis, J. B. The mechanism of mass transfer of solutes across liquid-liquid interfaces. Part I: The determination of individual transfer coefficients for binary systems. Chemical Engineering Science, 248–259 (1954).
Kruber, K. F., Krapoth, M. & Zeiner, T. Interfacial mass transfer in ternary liquid-liquid systems. Fluid Phase Equilibria 440, 54–63 (2017).
Reid, R. C. & Sherwood, T. K. Properties of liquids and gases (McGraw-Hill, New York, 1958).
Lehninger, A. L. Biochemistry. The molecular basis of cell structure and function (Worth Publishers, New York, 1970).
Kulaguin Chicaroux, A. & Zeiner, T. Theoretical and experimental investigation of mass transfer in aqueous two-phase systems based on linear and branched polymers. Fluid Phase Equilibria 479, 106–113 (2019).
Melgarejo-Torres, R. et al. Mass transfer coefficient determination in three biphasic systems (water–ionic liquid) using a modified Lewis cell. Chemical Engineering Journal 181-182, 702–707 (2012).
Kaplanow, I., Schmalenberg, M., Borgmann, I., Schembecker, G. & Merz, J. Tunable Aqueous Polymer Phase Impregnated Resins (TAPPIR®): Investigation of the impregnation stability. Separation and Purification Technology 190, 1–8 (2018).
Kulaguin-Chicaroux, A. & Zeiner, T. Novel aqueous two-phase system based on a hyperbranched polymer. Fluid Phase Equilibria 362, 1–10 (2014).
Kulaguin-Chicaroux, A. & Zeiner, T. Interfacial Behavior of Aqueous Two-Phase Systems Based on Linear and Hyperbranched Polymers. J. Chem. Eng. Data 63, 2467–2476 (2018).
Radziejewska, R.C., Leśnierowski, G. & Kijowski, J. Properties and application of egg white lysozyme and its modified preparations. A review. Polish Journal of food and nutrition sciences, 5–10 (2008).
Nitsch, W. & Weigl, M. Action of Amphiphilic Layers on the Kinetics of Interfacial Reactions at Liquid/Liquid Interfaces. Langmuir 14, 6709–6715 (1998).
Sutherland, I. A. et al. Rapid linear scale-up of a protein separation by centrifugal partition chromatography. Journal of Chromatography A 1190, 57–62 (2008).
Acknowledgements
The research leading to these results has received funding from the Ministry of Innovation, Science and Research of North Rhine-Westphalia (NRW) and by TU Dortmund University as scholarship in the frame of CLIB-Graduate Cluster Industrial Biotechnology (CLIB2021). We acknowledge financial support by Deutsche Forschungsgemeinschaft and Technische Universität Dortmund/TU Dortmund University within the funding programme Open Access Publishing.
Author information
Authors and Affiliations
Contributions
I.K. and F.G. designed experiments, carried out experiments and analysed data. I.K., J.M. and G.S. contributed to the writing of the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Kaplanow, I., Goerzgen, F., Merz, J. et al. Mass Transfer of Proteins in Aqueous Two-Phase Systems. Sci Rep 9, 3692 (2019). https://doi.org/10.1038/s41598-019-39797-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-019-39797-9
- Springer Nature Limited