Abstract
Extracting rare earth elements (REEs) from wastewater is essential for the growth and an eco-friendly sustainable economy. However, it is a daunting challenge to separate individual rare earth elements by their subtle differences. To overcome this difficulty, we report a unique REE nanotrap that features dense uncoordinated carboxyl groups and triazole N atoms in a two-fold interpenetrated metal-organic framework (named NCU-1). Notably, the synergistic effect of suitable pore sizes and REE nanotraps in NCU-1 is highly responsive to the size variation of rare-earth ions and shows high selectivity toward light REE. As a proof of concept, Pr/Lu and Nd/Er are used as binary models, which give a high separation factor of SFPr/Lu = 796 and SFNd/Er = 273, demonstrating highly efficient separation over a single step. This ability achieves efficient and selective extraction and separation of REEs from mine tailings, establishing this platform as an important advance for sustainable obtaining high-purity REEs.
Similar content being viewed by others
Introduction
Rare-earth elements (REEs) are used in a wealth of high-tech applications, including permanent magnets, lasers, phosphors, catalytic converters, and batteries1,2,3,4, owing to their 4 f peculiar electronic structure. To meet the REEs demands of the emerging clean energy technology market, recovery and separation of REEs from wastes is an eco-friendly sustainable strategy. However, achieving their selective separation and purification still faces a great challenge due to the large excess of interfering ions, low REE concentrations, and their highly similar chemical properties5,6.
Various approaches have been utilized to separate REEs. Fractional crystallization, as one of the earliest separation methods, which has low separation efficiency, owning to its driving force originates primarily from the ionic radii differences7,8. Currently, solvent extraction9,10,11, and liquid membrane separation methods12,13 have been utilized for the industrial separation REEs. A high separation factor can be achieved by hundreds of stages while it often faces problems such as low efficiency and generating massive of toxic secondary organic liquid waste14. Given this, several strategies have emerged to enhance the separation efficiency of REEs. For example, Schelter et al. based on the differences in the equilibrium constants of early and late metals complex with a tripodal nitroxide ligand to enhance the separation factor of Nd/Dy15. Bu et al. utilized the size-selective crystallization of rare-earth ions method to amplify the difference between early and late lanthanides16,17. Wang et al. controlled the reaction kinetics to separate Nd/Sm and Nd/Dy during the crystallization of borates3. However, these methods share many shortages of high temperature, long incubation times, and low efficiency, which hinder scale-up production and practical application3,16. Compared with the aforementioned methods, an adsorption method could overcome the above limits due to its easy operation, intrinsic economic feasibility, and little secondary pollution18. Traditional adsorbents of activated carbon19, metal oxides20, and composites21 have been developed for REEs extractive and separation, but they usually suffer from low selectivity and capacity because of their low adsorb sites or unsuitable pore sizes22. Therefore, integrating appropriate apertures and high-density active sites within one adsorbent is the key to enhancing the separation efficiency of REEs. Towards this end, metal-organic frameworks (MOFs) provided new opportunities for REEs separation owing to their tunable pore sizes and diverse functionalities at the molecular scale23,24,25,26. Given the fact that light REE ions exhibit a slightly larger size than the heavy REE ions and interfering ions in mine tailings27,28, we reasoned that it is essential to design a suitable aperture or form multiple interactions to enhance the interaction between the light/heavy REE ions and the host framework for efficient REE ions separation. Although these promising properties of MOFs for separation, only a few cases of the separation of REEs by MOFs have been reported. Recently, two hydroxyl-rich 0.8 nm hexagonal channel MOFs were reported for selective separation of lanthanides by solid-phase extraction, where the separation factor was only less than 2, ascribing to the weak affinity between REEs with hydroxyl groups29. Qiu et al. synthesized a Zn-BTC MOF/NG using a solid-phase in situ synthesis strategy, exhibiting excellent separation selectivity of REEs, which attributed to the synergistic effects of the three-dimensional pore of MOF and two-dimensional pore of NG30. Ahn et al. prepared a chromium-based MOF (Cr-MIL-101), and its derivatives with different organic functional groups for the adsorption of several REE ions. It demonstrated that the carboxylate (−COO − ), phosphonic (−PO32−), and nitrogen-containing groups have a strong coordinative affinity toward REE ions31. However, the reported materials have large pore sizes ranging from 1.2 to 2.2 nm, which were ineffective for the separation of different REEs31. It was reported that the crown ether (18-C-6) or macrocyclic molecules with about 3.2 Å cavity diameters show good selectivity for the large Ln3+ ions, due to the better matching of the crown ether cavity size with Ln3+ ions diameter32,33,34. We hypothesized that if the REE nanotrap is immobilized on the suitable pore size MOFs, it will not only provide strong interactions to capture REE ions but also obtain pure individual REE ions.
To explore the validity of this hypothesis, we synthesized a new 2D metal-organic framework (termed NCU-1) that features densely uncoordinated carboxyl groups and triazole N atoms, thus providing an REE-philic environment. Owing to the two-fold interpenetration, NCU-1 forms numerous small cavities (3.2 Å) that better match with the size/shape of light REE ions. Therefore, the synergistic effect of suitable apertures and multipoint functional sites in unique REE nanotraps results in a rare high light REE ions uptake and high separation factor for light/heavy REE ions over a single step (Fig. 1). The breakthrough experiments revealed that REE nanotraps could efficiently and selectively separate REE ions from mine tailings over a single step. Thereby, this work provides a powerful approach to obtain high-purity REEs.
Results
Synthesis and structure description of NCU-1
The light brown plate crystal of NCU-1 crystallizes in the orthorhombic space group, Pna21 (Supplementary Table 1). The morphology of NCU-1 and its size was studied by SEM, which showed bulk crystals of different sizes (Supplementary Fig. 1). Each Zn2+ is 5-coordinated and binds to two DTB ligands, two BTC, and one water molecule (Fig. 2a). Viewed from the a axis, rectangular windows with a size of 9.9 Å × 5.8 Å can be observed (Fig. 2b and Supplementary Fig. 2). Owing to the two-fold interpenetration, NCU-1 features numerous small square pockets decorated by multipoint functional sites (Fig. 2c). Each of such small pockets with a size of 3.2 Å is constructed by triazole rings and uncoordinated carboxylate groups that better match with the size/shape of the larger light REE ions (Fig. 2d and Supplementary Fig. 3). The PXRD pattern is consistent with that of the simulated one, indicating the phase purity of NCU-1 (Supplementary Fig. 4). Meanwhile, the chemical stabilities of NCU-1 were investigated upon treatments in various pH values ranging from 2 to 13. The crystallinity of this treated NCU-1 was still retained as evidenced by the PXRD patterns (Supplementary Fig. 5). Furthermore, according to the TG analysis, the NCU-1 showed high thermal stability up to 320 °C (Supplementary Fig. 6). These results suggest that NCU-1 exhibits good stability in harsh conditions, which is highly desirable for capturing and separating of REEs from mine tailings.
a The coordination environment of Zn2+. b The 2D extended framework of NCU-1. c The simplified topological structure of 2-fold interpenetration (different colors represent different single sets of the interpenetration). d The two fold-interpenetrated structure of NCU-1 produces numerous square small pockets. (Zn, magenta; C, dark gray; N, blue; O, red).
Sorption isotherm analysis
The adsorption isotherms of Pr3+, Nd3+, Eu3+, Gd3+, Dy3+, Er3+, and Lu3+ (Ln3+, Ln(NO3)3·6H2O) were explored at pH 4.5 as representative models of REE ions due to their abundance in mine tailings collected from Ganzhou city, Jiangxi province, a well-known REEs industry center in China (Supplementary Figs. 7-19 and Supplementary Table 2). The results showed that the seven Ln3+ were fitted well with the Langmuir adsorption model, and the maximum capacity (qm) of Pr3+, Nd3+, Eu3+, Gd3+, Dy3+, Er3+, and Lu3+ were analyzed by ICP-MS were 420, 310, 221, 140, 126, 97, and 66 mg/g, respectively (Fig. 3a, Supplementary Figs. 20-26, and Supplementary Table 3). This greatly exceeds the capacity of most current adsorbents, such as CA@Fe3O4 NPs35, KIT-6-1,3-PDDA36, MFC-O37, MIL-101-DGA38, and PEI800/ES-1/2.139. Energy dispersive X-ray spectroscopy (EDS) mapping analysis confirms that Pr3+, Nd3+, Gd3+, and Dy3+ entered the structures of the material with a uniform distribution throughout the samples (Supplementary Fig. 27). In X-ray photoelectron spectroscopy (XPS) (Supplementary Figs. 28-31), the characteristic peaks of Pr3+, Nd3+, Eu3+, and Er3+ were clearly found after adsorption of Pr3+, Nd3+, Eu3+, and Er3+, respectively. As depicted in Supplementary Fig. 32, after capturing Pr3+, the XRD of NCU-1 shows the shift of some peak sites as compared to the pristine one, which can be attributed to the adsorption of Pr3+ on the pores of NCU-1 and interacted with them.
a Equilibrium data for Pr3+, Nd3+, Gd3+, and Dy3+ adsorption of NCU-1 and fitted with the Langmuir isotherm models. b Kd values of metal ions captured by NCU-1 at various pH values from 2.0 to 6.0. c NCU-1 capture efficiency of metal ions in mine tailings collected from Ganzhou city. d Mine tailing breakthrough curves of metal ions. Error bars represent S.D. n = 3 independent experiments.
Sorption kinetics analysis
The kinetics of NCU-1 for individual Pr3+, Nd3+, Eu3+, Gd3+, Dy3+, Er3+, and Lu3+ adsorption were then investigated (Supplementary Figs. 33-46 and Supplementary Table 4). The REE ions were rapidly captured by NCU-1, all of which reached equilibrium within 1 h, much shorter than those of the other adsorbents. For example, magnetite@MOF40 and hydroxyl-decorated flexible MOF29, require longer than 2–4 h to reach equilibrium. Additionally, for any sorbents, recyclability is crucial for practical implementation. Significantly, the adsorption processes were fully reversible as reflected by the fact that the loaded REE ions can be washed off by diluted HNO3 at pH 3 with maintained capture efficiency for at least four cycles of sorption/desorption (Supplementary Figs. 47-50). After the fourth cycle, the crystallinity of NCU-1 was maintained, as confirmed by PXRD studies (Supplementary Fig. 51). In addition, the morphology of the fourth reuse of NCU-1 is almost unchanged (Supplementary Fig. 52). The results indicate that NCU-1 can serve robustly towards highly efficient REEs recovery and affirm the judicious choice of the MOF for affording selective trapping REEs.
Selectivity
The selectivity of REE ions is a key parameter for evaluating adsorbents. Thereby, the distribution coefficient (Kd) as a barometer for selectivity was also tested. NCU-1 was dispersed in the mixed solutions containing REE ions and interfering ions with different pH values ranging from 2.0 to 6.0 (Fig. 3b). The Kd of NCU-1 to REEs increases rapidly and reaches the maximum when the pH increases from 2.0 to 4.5, and then decreases to 6.0 (Supplementary Table 5). Compared to transition metal ions and alkaline-earth metal ions, the Kd of NCU-1 to REE ions is 3–4 orders of magnitude higher, suggesting a clear advantage of NCU-1 in selective capture of REE ions. Remarkably, the Kd to various rare-earth ions differs significantly at pH 4.5, which induces that the optimal separation selectivity for REEs can be achieved. Generally, a material is considered an excellent adsorbent if Kd is over 104 mL g-1. Particularly, Kd Gd-La was up to 1.6 × 104–1.0 × 106 mL g-1 at pH 4.5. Such high Kd indicates that NCU-1 has an obviously higher affinity toward light REE ions.
Tailings treatment
Encouraged by the excellent performance of NCU-1 for extraction and separation of REE ions, we evaluated the ability of NCU-1 to capture and separate REE ions from mine tailing collected from Ganzhou city. The natural rare-earth tailing sample was filtered through a 0.22 µm filter for ICP-MS analysis. The results show that the concentrations of rare earth elements in the tailing are low about 0.09–0.92 ppm, and the competitive ions concentration of Al (8.15 ppm) is about 10 times compared to those of the REEs (Supplementary Table 2), making the REEs adsorption and separation a great challenging task. Except for competing ions, the NCU-1 could effectively selective capture all REE ions from the natural mine tailing (Fig. 3c), manifesting it is a good platform for adsorption and separation of REEs from mine tailings. As an industrially relevant performance test, experimental breakthrough studies were performed to evaluate the actual separation ability of NCU-1 (Supplementary Fig. 53). The competitive ions occurs first at 10 bed volumes and REE ions occur after 50 bed volumes (Fig. 3d and Supplementary Fig. 54), indicating NCU-1 has an excellent separation effect on REE ions from competitive ions. It is worth noting that compared to heavy REE ions, light REE ions have even higher uptakes and larger breakthrough bed volumes. For instance, the breakthrough bed volume of Pr3+ is 150, which is larger than that of Dy3+ (80) (Supplementary Fig. 55). The results illustrate that NCU-1 is a promising candidate for separation and obtaining high purity REE ions from mine tailing over a single step.
Separation mechanism
The FT-IR and XPS were applied to evaluate the structure-performance relationship of NCU-1 in the effective capture of REE ions. After adsorption Pr3+ and Nd3+, the signal of -COOH shows a large blue shift of 22.1 cm-1 and 20.0 cm-1, respectively (from 1574.5 cm-1 to 1552.4 cm-1 and 1554.5 cm-1)26, and the peak of N atoms from triazole has a 12.7 cm-1 and 11 cm-1 (from 1519.2 cm-1 to 1531.9 cm-1 for Pr3+, and 1530.2 cm-1 for Nd3+, respectively) redshift (Supplementary Figs. 56 and 57), illustrating that the robust interaction between Ln3+ and carboxyl groups and triazole groups in NCU-1. As shown in Supplementary Fig. 28, the character peak at 933.95 eV of NCU-1-Pr ascribed to Pr 3d5/2 demonstrated that Pr3+ was successfully adsorbed into the NCU-1. After adsorption of Nd3+, distinctive Nd 3d5/2 and 3d3/2 peaks appeared at 982.95 and 1005.59 eV, which had a great blue shift of 0.85 eV compared to the signal (BE, 983.70 eV) of Nd 3d5/2 in Nd(NO3)341, indicating that Nd3+ was successfully loaded onto the NCU-1 and had strong interaction between them (Supplementary Fig. 29). In the O 1 s high-resolution spectrum, the signals at 531.36 eV and 533.01 eV are assigned to -COOH and water, respectively (Supplementary Fig. 58). Obviously, the peak at 531.36 eV of –COOH in NCU-1 has a significant positive shift by 0.60 eV and 0.18 eV after capturing Pr3+ and Nd3+ respectively, proving strong interactions between Ln3+ and the carboxyl in NCU-1, which is consistent with the results of the C 1 s high-resolution spectrum (Supplementary Figs. 59-63). In addition, the binding energies at 533.01 eV of NCU-1 shifted by 0.49 eV and 0.37 eV to higher binding energy after extraction of Pr3+ and Nd3+, respectively. These results suggest that the water molecules have also participated in the coordination of rare-earth ions. Comparing the N 1 s peaks in the before and after adsorption Ln3+ of two different samples (Supplementary Figs. 64-66), the -NH (399.98 eV) peak shifted by 0.40 eV and 0.36 eV to lower binding energy after extracting Pr3+ and Nd3+, respectively. After adsorption of Pr3+ and Nd3+, the -C = N- peaks at 401.44 eV were changed to 401.28 and 401.36 eV, respectively. This implies that triazolium nitrogen atoms in NCU-1 were also involved in the coordination of Ln3+. In conclusion, the results show that the high adsorption toward REE ions of NCU-1 is ascribed to the strong coordination ability between the REE ions and carboxyl groups, lattice water molecules, and triazolium nitrogen atoms in the host.
To examine the crystal structures of the NCU-1-REEs ions in greater detail, we performed additional investigations using Cryo-Electron Microscopy (Cryo-EM). As shown in Fig. 4a, the NCU-1 has distinct lattice fringes with a spacing of 0.192, corresponding to the (316) crystal planes. The Cryo-EM image of NCU-1-Pr and NCU-1-Nd with obvious lattice fringes evidenced the highly crystalline nature after adsorbing REEs. Among these, the lattice spacings of 0.231 nm and 0.320 nm, correspond to the (-113) crystal planes of Pr2O3 and (100) of Nd2O3, respectively42,43 (Fig. 4b, c). These results suggested that the rare earth ions may be trapped by REE nanotrap and interact with the oxygen atoms of carboxylic acid in NCU-1 to form oxide species.
elucidate the origin of the observed high selectivity of the NCU-1 for REE ions, the first principle calculations were carried out between metal ions and the NCU-1 configurations. Al3+, Dy3+, and Pr3+ were selected as the representative interfering ions, heavy REEs ions, and light REE ions, respectively. Figure 5a–c show the differential charge density (DCD) maps of NCU-1 configurations after adsorption Al3+, Dy3+, and Pr3+, respectively. Obviously, charge redistribution occurs at metal ions and NCU-1, and the negatively charged regions (yellow) with excess electrons accumulate around the O atoms and N atoms, which are beneficial to the adsorption of metal ions44,45. The Bader charge analysis46 shows that the charges on Al3+ ion in the NCU-1 configuration are +2.09 e, while +2.17 e for Dy3+, and increase to +2.31 e for Pr3+. Generally, the larger the Bader charge, the stronger the binding strength between the host and guests47. Therefore, the order of the binding strength of NCU-1 with the three ions is as follows: Al3+<Dy3+<Pr3+. It suggests that the selectivity of NCU-1 for light REE ions is higher than those of heavy REE ions and interfering ions, due to the more electrons obtained from the host. Moreover, the density functional theory (DFT) calculation clearly reveals that the primary adsorption sites of metal ions are located at the REE nanotraps (Fig. 5d–f). As for Pr3+, two oxygen atoms of the carboxyl group and one water molecule were calculated to coordinate with Pr3+ with the bond distances of 1.79 Å, 2.73 Å, and 1.94 Å, respectively (Supplementary Fig. 67). The calculated distance of Pr3+···N in NCU-1 is 3.30 Å. In the case of Nd3+, it is coordinated to the two oxygen atoms of the carboxyl group and one water molecular with the bond distances of 1.66 Å, 2.76 Å, and 1.86 Å, respectively, and the Nd3+···N bond distance is about 3.27 Å (Supplementary Fig. 68). While as for Al3+, only the coordination bonds between the carboxyl and water molecular oxygen and Al3+ were calculated (Supplementary Fig. 69). The adsorption energies (Eads) of NCU-1 with different metal ions were also calculated to discriminate the adhesion level. The calculated adsorption energy for Al3+, Dy3+, and Pr3+ are -1.66 eV, -2.58 eV and -3.29 eV, respectively. It decreases when the size of the adsorbed ions increases, which is fully consistent with our experimental observations. This is partly because the larger Pr3+ (r = 0.99 Å) sterically “matches” better to the nanotraps size/shape than Dy3+ (r = 0.91 Å) and Al3+ (r = 0.50 Å)6,17. Light REE ions within a larger size radius enter the REE nanotraps and form stable complexes with the uncoordinated carboxylic groups and N atoms in the NCU-130. However, competing ions and heavy rare earth ions with a large difference in pore size from NCU-1 have poor binding ability to coordinate with O, which makes the ions easily escape from the pores and achieve high-selectivity separation of light RREs. Therefore, the suitable sizes of the nanotraps and the uncoordinated carboxyl groups and N atoms in nanotraps play a decisive role in the light/heavy REE separation.
Differential charge distribution of NCU-1 configuration after adsorption with a Pr3+, b Dy3+, and c Al3+ with the corresponding Bader charges. The Bader charge on the metal ion is defined as qM. Optimized structures of NCU-1 and the adsorption energy of metal ions d Pr3+, e Dy3+, and f Al3+ (Pr3+, yellow; Dy3+, purple; Al3+, light blue).
Binary REE ions separation
Since the affinity of NCU-1 to REE ions exhibits a unique periodic trend with significant differences, the individual REE can be separated from other REEs by the adsorption method (Fig. 3b). As a proof of concept, a series of experiments (6 combinations in total) were conducted to determine its application on individual REE separations. Consequently, NCU-1 was dispersed into binary mixtures of REE ions (M1 and M2) in a 1:1 molar ratio. As shown in Fig. 6, larger Ln3+ is selectively adsorbed by NCU-1, and smaller Ln3+ almost remained in the solution, indicating that this system successfully separated light/heavy REE mixtures. For a mixtures that contained Nd3+ and Dy3+, the separation factor (SF) reached up to 67, which exceeded those of many materials, for example, TriNOx3- (SFNd:Dy = 8.45 ± 1.62)4, Zn-BTC (SFNd:Dy = 30.23)30, TRPO (SFNd:Dy < 5)11. Especially interesting is the separation factor of 73 observed for Eu3+ over Lu3+, a value that is high than that of the crystallization extraction method recently developed by Wang et al.3. Impressively, the case of Pr/Lu, obtains a high separation factor of 796, which is one of the highest single-step separation factors known for REEs separations48. Mixtures that contained Nd: Er also gave a large separation factor of SFNd: Er = 273. Generally, NCU-1 demonstrates a clear and high preference for larger-sized REE ions in the solid adsorption process, and the selectivity increases with the ionic radii difference. High-purity individual rare-earth ions can be obtained through one-step adsorption in this work, which has made a breakthrough process in the separation of REEs.
Discussion
In conclusion, we report a unique REE nanotrap featuring dense uncoordinated carboxyl groups and triazole N atoms and suitable pore sizes in NCU-1 that can induce strong interaction with light REE ions. Thereby the NCU-1 affords outstanding light REEs adsorption and separation performance for potential use in capturing REEs from mine tailings. Notably, the high response to light REE is firstly realized by simple adsorption progress, which could obtain high purity individual REEs over a single step. Not only does this work report a promising platform that offers a solution to the long-term challenge of REEs recovery from complex wastewater systems, but it also sheds light on the rational design of metal framework materials for applications in the field of REE purification.
Methods
Materials
4,4-di(4H-1,2,4-triazol-4-yl)-1,1-biphenyl (DTB) and trimesic acid (BTC) were purchased from Jilin Chinese Academy of Sciences-Yanshen Technology Co., Ltd. Zn(NO3)·6H2O and trivalent lanthanide nitrates were purchased from Energy Chemical Co., Ltd. Acetonitrile (MeCN) and ethanol were purchased from Sinopharm Chemical Reagent Co., Ltd. Ultrapure water was prepared from the Millipore system (18.25 MΩ cm). All the purchased reagents were of analytical grade and used without further purification.
Synthesis of NCU-1
To a 20 mL PTFE reactor, trimesic acid (21.0 mg, 0.10 mmol), 4,4-di(4H-1,2,4-triazol-4-yl)-1,1-biphenyl (28.8 mg, 0.10 mmol), Zn(NO3)·6H2O (29.5 mg, 0.1 mmol), MeCN 2 mL, and water 8 mL were added. The mixture was sealed and heated 140 °C for 3 days, followed by slow cooling at a rate of 5 °C/h to room temperature, and light brown crystals for X-ray analysis were collected and dried in air.
Data availability
The data that support the findings of this paper are available in the paper and supplementary information files. The X-ray crystallographic data for the structure reported in this article has been deposited at the Cambridge Crystallographic Data Centre (CCDC) with the number CCDC 2141439. Any further relevant data are available from the corresponding authors upon request.
References
Binnemans, K. Lanthanide-based luminescent hybrid materials. Chem. Rev. 109, 4283–4374 (2009).
Woodruff, D. N. et al. Lanthanide single-molecule magnets. Chem. Rev. 113, 5110–5148 (2013).
Yin, X. et al. Rare earth separations by selective borate crystallization. Nat. Commun. 8, 14438 (2017).
Higgins, R. F. et al. Magnetic field directed rare-earth separations. Angew. Chem. Int. Ed. 59, 1851–1856 (2020).
Li, X. Z. et al. A supramolecular lanthanide separation approach based on multivalent cooperative enhancement of metal ion selectivity. Nat. Commun. 9, 547 (2018).
Qi, X. H. et al. Layered A2Sn3S7·1.25H2O (A = organic cation) as efficient ion-exchanger for rare earth element recovery. J. Am. Chem. Soc. 139, 4314–4317 (2017).
Lu, H. et al. Size-dependent selective crystallization using an inorganic mixed-oxoanion system for lanthanide separation. Dalton Trans. 48, 12808–12811 (2019).
Zhu, Z. et al. Separation of uranium and thorium from rare earths for rare earth production–A review. Min. Eng. 77, 185–196 (2015).
Xie, F. et al. A critical review on solvent extraction of rare earths from aqueous solutions. Min. Eng. 56, 10–28 (2014).
Sun, P. et al. Antagonistic role of aqueous complexation in the solvent extraction and sseparation of rare earth ions. ACS Cent. Sci. 7, 1908–1918 (2021).
Sun, X. et al. Synergistic effect between bifunctional ionic liquids and a molecular extractant for lanthanide separation. ACS Sustain. Chem. Eng. 2, 2758–2764 (2014).
Yaftian, M. R. et al. Rare-earth metal-ion separation using a supported liquid membrane mediated by a narrow rim phosphorylated calix[4]arene. J. Membr. Sci. 144, 57–64 (1998).
Nazari, A. M. et al. Selective heavy rare earth element extraction from dilute solutions using ultrasonically synthesized Cyanex 572 oil droplets and Cyanex 572-impregnated resin. J. Ind. Eng. Chem. 59, 388–402 (2018).
Panak, P. J. et al. Complexation and extraction of trivalent actinides and lanthanides by triazinylpyridine N-donor ligands. Chem. Rev. 113, 1199–1236 (2013).
Bogart, J. A. et al. An operationally simple method for separating the rare-earth elements neodymium and dysprosium. Angew. Chem. Int. Ed. 54, 8222–8225 (2015).
Zhao, X. et al. Size-selective crystallization of homochiral camphorate metal–organic frameworks for lanthanide separation. J. Am. Chem. Soc. 136, 12572–12575 (2014).
Yang, H. et al. Selective crystallization of rare-earth ions into cationic metal-organic frameworks for rare-earth separation. Angew. Chem. Int. Ed. 60, 11148–11152 (2021).
Florek, J. et al. Understanding selectivity of mesoporous silica-grafted diglycolamide-type ligands in the solid-phase extraction of rare earths. ACS Appl. Mater. Interfaces 12, 57003–57016 (2020).
Gad, H. M. H. et al. Factors affecting on the sorption/desorption of Eu (III) using activated carbon. Separ. Sci. Technol. 42, 3657–3680 (2007).
Tan, X. et al. Grambow B. Eu(III) sorption to TiO2 (anatase and rutile): batch, XPS, and EXAFS studies. Environ. Sci. Technol. 43, 3115–3121 (2009).
Zhao, C. et al. Synthesis of a flower-like MoS2/carbon nanocomposite with enhanced adsorption performance toward Eu(III): the cooperative effects between S atoms and carboxyl groups. Environ. Sci. Water Res. Technol. 6, 1482–1494 (2020).
Sun, H. et al. Highly selective recovery of lanthanides by using a layered vanadate with acid and radiation resistance. Angew. Chem. Int. Ed. 59, 1878–1883 (2020).
Furukawa, H. et al. The chemistry and applications of metal-organic frameworks. Science 341, 1230444 (2013).
Furukawa, S. et al. Structuring of metal–organic frameworks at the mesoscopic/macroscopic scale. Chem. Soc. Rev. 43, 5700–5734 (2014).
Ding, M. et al. Carbon capture and conversion using metal–organic frameworks and MOF-based materials. Chem. Soc. Rev. 48, 2783–2828 (2019).
Muschi, M. et al. Formation of a single-crystal aluminum-based MOF nanowire with graphene oxide nanoscrolls as structure-directing agents. Angew. Chem. Int. Ed. 59, 10353–10358 (2020).
Kegl, T. et al. Adsorption of rare earth metals from wastewater by nanomaterials: a review. J. Hazard. Mater. 386, 121632 (2020).
Goodenough, K. M. et al. The rare earth elements: demand, global resources, and challenges for resourcing future generations. Nat. Resour. Res. 27, 201–216 (2018).
Mon, M. et al. Lanthanide discrimination with hydroxyl-decorated flexible metal–organic frameworks. Inorg. Chem. 57, 13895–13900 (2018).
Wu, J. et al. Highly selective separation of rare earth elements by Zn-BTC metal–organic framework/nanoporous graphene via in situ green synthesis. Anal. Chem. 93, 1732–1739 (2021).
Lee, Y. R. et al. Selective adsorption of rare earth elements over functionalized Cr-MIL-101. ACS Appl. Mater. Interfaces 10, 23918–23927 (2018).
Roca-Sabio, A. et al. Macrocyclic receptor exhibiting unprecedented selectivity for light lanthanides. J. Am. Chem. Soc. 131, 3331–3341 (2009).
Zhou, J. Z. et al. The stability of coordination compounds of some crown ethers with lanthanide(III) ions. Inorg. Chim. Acta 94, 41–43 (1984).
Calderón, V. et al. Selective solid–liquid extraction of cations using solid-phase polyamides with crown ether moieties as cation host units. J. Appl. Polym. Sci. 106, 2875–2884 (2007).
Ashour, R. M. et al. Selective separation of rare earth ions from aqueous solution using functionalized magnetite nanoparticles: kinetic and thermodynamic studies. Chem. Eng. J. 327, 286–296 (2017).
Hu, Y. et al. Size-selective separation of rare earth elements using functionalized mesoporous silica materials. ACS Appl. Mater. Interfaces 11, 23681–23691 (2019).
Brown, A. T. et al. Critical rare earth element recovery from coal ash using microsphere flower carbon. ACS Appl. Mater. Interfaces 13, 48492–48499 (2021).
Lin, W. et al. Promising priority separation of europium from lanthanide by novel DGA-functionalized metal organic frameworks. Min. Eng. 164, 106831 (2021).
Wang, Q. et al. Amine sorbents for selective recovery of heavy rare-earth elements (dysprosium, ytterbium) from aqueous solution. ChemPlusChem 85, 130–136 (2020).
Elsaidi, S. K. et al. Extraction of rare earth elements using magnetite@MOF. Compos. J. Mater. Chem. A 6, 18438–18443 (2018).
Lu, Q. et al. Postsynthetic functionalization of tthree-dimensional covalent organic frameworks for selective extraction of lanthanide ions. Angew. Chem. Int. Ed. 57, 6042–6048 (2018).
Casillas, J. E. et al. Photocatalytic degradation of diclofenac using Al2O3-Nd2O3 binary oxides prepared by the sol-gel method. Mater 13, 1345 (2020).
Xin, Y. et al. Fabrication of honeycomb-structured composite material of Pr2O3, Co3O4, and graphene on nickel foam for high-stability supercapacitors. N. J. Chem. 47, 211–219 (2023).
Xie, F. et al. Screening heteroatom configurations for reversible sloping capacity promises high-power Na-ion batteries. Angew. Chem. Int. Ed. 61, e202116394 (2022).
Zhang, Y. et al. Stable unbiased photo-electrochemical overall water splitting exceeding 3% efficiency via covalent triazine framework/metal oxide hybrid photoelectrodes. Adv. Mater. 33, 2008264 (2021).
Henkelman, G. et al. A fast and robust algorithm for bader decomposition of charge density. Comp. Mater. Sci. 36, 354–360 (2006).
Xu, Z. L. et al. Exceptional catalytic effects of black phosphorus quantum dots in shuttling-free lithium sulfur batteries. Nat. Commun. 9, 4164 (2018).
Healy, M. R. et al. Efficient separation of light lanthanides(III) by using bis-lactam phenanthroline ligands. Chem. – Eur. J. 25, 6326–6331 (2019).
Acknowledgements
We acknowledge financial support from the National Natural Science Foundation of China (22036003, 22176082, and 22376023), and the Natural Science Foundation of Jiangxi Province (20232BBE50031).
Author information
Authors and Affiliations
Contributions
J.-D.Q. and Q.-H.H. conceived and designed the research. Q.-H.H. performed the synthesis and conducted the experiments. Q.-H.H., A.-M.S, X.G., Y.-Z.S., and W.J. performed the characterizations. Q.-H.H., R.-P.L., and J.-D.Q. participated in drafting the paper and approved the final version of the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Jesús Ferrando-Soria, Eveliina Repo and the other, anonymous, reviewer(s) for their contribution to the peer review of this work.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Hu, QH., Song, AM., Gao, X. et al. Rationally designed nanotrap structures for efficient separation of rare earth elements over a single step. Nat Commun 15, 1558 (2024). https://doi.org/10.1038/s41467-024-45810-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-024-45810-1
- Springer Nature Limited