Abstract
Exceptional point degeneracies (EPD) of linear non-Hermitian systems have been recently utilized for hypersensitive sensing. This proposal exploits the sublinear response that the degenerate frequencies experience once the system is externally perturbed. The enhanced sensitivity, however, might be offset by excess (fundamental and/or technical) noise. Here, we developed a self-oscillating nonlinear platform that supports transitions between two distinct oscillation quenching mechanisms – one having a spatially symmetric steady-state, and the other with an asymmetric steady-state – and displays nonlinear EPDs (NLEPDs) that can be employed for noise-resilient sensing. The experimental setup incorporates a nonlinear electronic dimer with voltage-sensitive coupling and demonstrates two-orders signal-to-noise enhancement of voltage variation measurements near NLEPDs. Our results resolve a long-standing debate on the efficacy of EPD-sensing in active systems above self-oscillating threshold.
Similar content being viewed by others
Introduction
The underlying mathematical structures of non-Hermitian wave systems1,2,3,4 have inspired the last few years new technologies5,6,7,8. Many of these are reliant on the existence of exceptional point degeneracies (EPDs)8. These are non-Hermitian degeneracies where a set of N eigenvalues and their corresponding eigenvectors coalesce1,2. In the proximity of an Nth order EPD (EPD-N), the eigenvalue detuning Δf ≡ |f − fEPD|, due to a small external perturbation ε, follows a sublinear response (SLR) \(\Delta f\sim \root {N} \of{\varepsilon}\, \gg \, \varepsilon\) that can be utilized for enhanced sensing9,10,11,12,13,14,15.
A principal requirement for efficient EPD sensing is the increase of the resolution limit via the narrowing of the resonance linewidth. This can be achieved by judicious design of cavity amplification mechanisms. The downside of this strategy is that it introduces additional noise that, in some EPD platforms, might offset the enhanced signal sensitivity13,16,17,18,19. Furthermore, nonlinear effects might become important—requesting the development of theoretical tools that treat them on equal footing with the sensitivity enhancement near EPDs. However, most current studies rely on linear mathematical constructs, such as the Petermann factor20,21,22, which describes the linewidth enhancement near EPDs due to the bi-orthogonal nature of the eigenmodes of the underlying linear non-Hermitian systems16. Obviously, this approach is not suitable when the response of a system is influenced by nonlinearities. An example case is a laser at an EPD. Fortunately, an appropriate language exists from the area of dynamical systems and bifurcation theory23,24,25,26,27, which can be adopted for the analysis of nonlinear EPDs (NLEPDs). Examples of systems that are amenable to such analysis are shown in Fig. 1a. In fact, some recent theoretical studies have utilized this approach to address issues like the formation of NLEPDs and the emulation of neuronal dynamic functions using parity-time \(({{{{{\mathscr{P}}}}}}{{{{{\mathscr{T}}}}}})\) symmetric systems that involve gain and loss nonlinear channels26,27. These neuromorphic functionalities, belong to the general category of oscillation quenching mechanisms, whose characteristics are determined by the underlying dynamical symmetries of the system28,29,30. Oscillation quenching mechanisms occur in systems of coupled nonlinear oscillators, and can be classified in two different types30: oscillation death (OD), which is associated with the formation of an inhomogeneous steady state, and amplitude death (AD), which results in a homogenous steady state. These mechanisms have been observed in a variety of dynamical systems ranging from climate, lasers, electronic circuits, chemical systems, neurons, and more (for indicative references, see review paper30). Recently, in the framework of non-Hermitian photonic systems with \({{{{{\mathscr{P}}}}}}{{{{{\mathscr{T}}}}}}\)-symmetry, oscillation quenching mechanisms have been proposed, theoretically, for topological protection, signal processing26,27 and memory devices31. The interplay of \({{{{{\mathscr{P}}}}}}{{{{{\mathscr{T}}}}}}\)-symmetry and oscillation quenching were also theoretically discussed in the framework of electronic circuits. These theoretical studies highlighted a connection between a broken (exact) \({{{{{\mathscr{P}}}}}}{{{{{\mathscr{T}}}}}}\)-symmetric phase and an OD (AD) oscillation quenching mechanism, see Fig. 1b.I and Fig. 1b.II, respectively. The transition between these two regimes is characterized by the formation of a NLEPD (see Fig. 1b right and Fig. 1c). Can these NLEPDs be used for sensing and what is the signal-to-noise enhancement (SNE) factor in their proximity? A definite answer to this question requires not only a theoretical modeling24,25,32,33,34,35,36, but, most importantly, the establishment of controllable experimental platforms that will scrutinize the predictions of the theory, and guide the theoretical language as it is developing.
Here, we address the viability of NLEPD sensing protocols using two nonlinear RLC tanks whose capacitive coupling is used as a sensing platform for voltage variations. The RLC circuits have anharmonic parts consisting of a complementary amplifier (gain) and a dissipative conductor (loss), see Fig. 1a and “Methods.” The nonlinear supermodes (NS) are the fixed points of the dynamical equations, and their properties arise from the underlying dynamical symmetries and stability. We focus on stable NS that are experimentally accessible and these are identified from the (negative) real part of the eigenvalues {λn} of the Jacobian matrix—which describes the linearized dynamics around each of these fixed points23. Their properties lead to the partition of the parameter space into three distinct domains (see domains I, II, III in Fig. 1b right). The last of them, domain III, involves trivial NS with zero amplitude at each RLC tank (see inset of right subfigure of Fig. 1b) and is therefore irrelevant to our investigations. The other two domains, are separated by a NLEPD (see red line in right subfigure of Fig. 1b and red point in Fig. 1c) and contain one (two) non-trivial stable hyperbolic fixed points in the OD (AD) phase, see Fig. 1c (and Fig. 1b.I and Fig. 1b.II, respectively). The stable NS in the AD phase coalesce at the NLEPD-point at a voltage variation δV = 0, where δV controls the capacitive coupling between the two resonators. The detuned eigenfrequencies follow a characteristic SLR, \(\varDelta {f}_{\pm }\equiv {f}_{\pm }-{f}_{{{{{{\rm{{NLEPD}}}}}}}}\propto \pm \sqrt{\delta V}\), leading to two-orders enhancement of sensitivity to small voltage variations, and a similar SNE near the NLEPD, see Fig. 1c. Our results challenge the validity of linear concepts (e.g., Petermann factor) for the noise analysis near NLEPDs, and confirm beyond doubt that self-oscillating systems above threshold have an enhanced signal-to-noise sensing performance in the proximity of the NLEPDs.
Results
Experimental platform
The sensor consists of a pair of nonlinear RLC resonators37,38,39,40 (see Fig. 1a) with natural frequency \({f}_{0}=\frac{1}{2\pi }\frac{1}{\sqrt{{LC}}}\, \approx \, 338\,{{{{{{\rm{kHz}}}}}}}\), and an impedance (at resonance) \({Z}_{0}=\sqrt{\frac{L}{C}}\approx 424\,\Omega\). One of the resonators (gain—indicated with red in Fig. 1a) incorporates a nonlinear amplifier, −R1(V1), which is characterized by an I–V curve of \({I}_{1}({V}_{1})=-\frac{{V}_{1}}{{R}_{1}^{\left(0\right)}}+b{V}_{1}^{3}\) while the other one (loss—indicated with green in Fig. 1a) incorporates a nonlinear loss, R2(V2), with an I–V curve of \({I}_{2}({V}_{2})=\frac{{V}_{2}}{{R}_{2}^{\left(0\right)}}+b{V}_{2}^{3}\) (where b ≈ 7 · 10−4 AV−3 and V1(2) are the voltages at the nodes 1(2)). The two resonators are coupled together via a capacitance voltage controlled (CVC) capacitor Cκ(V) = κ · C where κ is a dimensionless parameter representing the strength of the coupling. The linear conductances, \(\frac{1}{{R}_{1}^{\left(0\right)}} > \frac{1}{{R}_{2}^{\left(0\right)}}\), were tuned such that the system undergoes a transition from AD to OD as the voltage at the coupling capacitor varies (see Fig. 1b, c and “Methods”). A transmission line (TL) with impedance z0 = 50 Ω is weakly coupled to each resonator via capacitors Ce ≪ C. The TLs were used to collect and direct the signal generated by the circuit to a VNA for further processing (see “Methods”). The NLEPD (occurring at δV = 0) can be experimentally identified as the point for which the voltage amplitudes \(\frac{{V}_{1}}{{V}_{2}}\) of each RLC resonator deviates from unity (AD domain) and begins to acquire larger values (OD domain)—see Fig. 2b.
Theoretical analysis of nonlinear supermodes
The voltage dynamics Vn at each RLC tank (n = 1,2), is described via a temporal coupled mode theory (TCMT) (see Supplementary Notes 1 and 2)
where \({a}_{n} \equiv \sqrt{\frac{3}{8}b{Z}_{0}}\left({V}_{n}+i\frac{1}{2\pi }\frac{{\dot{V}}_{n}}{{f}_{0}}\right),{\gamma }_{n}={\gamma }_{n}^{\left(0\right)}+{\left(-1\right)}^{n}({|{a}_{n}|}^{2}+\eta ),\, {\nu }_{\kappa }=1-\frac{\kappa }{2}-\sqrt{\frac{\eta }{2}\frac{{Z}_{0}}{{z}_{0}}}\) and \(\tau \equiv 2\pi {f}_{0}{{{{{\rm{t}}}}}}\) is the rescaled time. The parameters \({\gamma }_{n}^{(0)}\) are the linear gain (n = 1) and loss (n = 2) coefficients associated with the gain and loss RLC resonator, respectively, while \(\eta \equiv \frac{1}{2}\frac{{z}_{0}}{{Z}_{0}}{\left(\frac{{C}_{e}}{C}\right)}^{2}\) models the coupling of the circuit to the TLs. The global frequency shift fκ = f0 · νk is associated with the renormalization of the natural frequency f0 of the RLC resonators due to the capacitive coupling between them (κ-term) and the coupling with the TLs (η-term). The κ-dependence could be, in principle, avoided if we choose another type of coupling (e.g., inductive coupling). Below, we analyze the steady-state properties of Eq. (1) in terms of the coupling parameter κ = κ(δV), which is used as a sensing platform of voltage variations δV (see “Methods”).
The nonlinearities in our system have been chosen carefully to prevent the system from evolving towards undesirable unbounded states where A1 and/or A2 → ∞. This can be easily realized from Eq. (1) by recognizing that whenever the field intensity of the gain resonator exceeds a critical value \({\left|{a}_{1}\right|}^{2} > {\gamma }_{1}^{(0)}-\eta\) the gain coefficient γ1 becomes negative, thus turning the gain RLC tank into a lossy one. The NS of Eq. (1) may be expressed in the polar representation \({a}_{n}={A}_{n}{e}^{i{\varphi }_{n}}{e}^{-\frac{{if}\tau }{{f}_{0}}}\) and are identified as the fixed points of the dynamical system whose evolution is defined in a three-dimensional phase space (A1,A2,φ ≡ φ2 − φ1). We classify these fixed points according to their underlying (dynamical) symmetry, and stability. The latter is determined by the eigenvalues {λ1,λ2,λ3} of the 3 × 3 Jacobian matrix, J, when evaluated at the fixed point (see Supplementary Note 5)23. When Re(λn) ≠ 0 (∀n = 1,2,3), the fixed point is a hyperbolic equilibrium and there is a homeomorphism that maps the phase portrait in its proximity onto solutions of its linearized system described by J41. When all Re(λn) < 0, the fixed point is stable, and it is unstable if at least one Re(λn) > 0. Hyperbolic equilibria are robust to small variations which do not, qualitatively, change the phase portrait. The opposite scenario of non-hyperbolic equilibria is associated with cases where either one of the eigenvalues of the Jacobian matrix is zero or has a zero real part. These are structurally unstable cases, and one can numerically test the nature of the stability of these fixed points by direct dynamical simulations with Eq. (1).
We have found that one fixed point of Eq. (1) is a trivial state (A1,A2) = (0,0). The dynamical simulations indicate that it is stable in the parametric domain III (see Fig. 1b) while it is unstable in the other two domains. Below, we analyze the stable non-trivial fixed points occurring in domains I and II of Fig. 1b. In these cases, the real-valued amplitudes An > 0 take the form (see Supplementary Note 4 and Supplementary Fig. 2):
where the real-valued variable \(\rho \equiv \frac{{A}_{2}}{{A}_{1}} > 0\) is a solution of the quartic algebraic equation \(1-2\rho \big(\frac{{\gamma }_{2}^{\left(0\right)}+\eta }{\kappa }\big)-2{\rho }^{3}\big(\frac{{\gamma }_{1}^{\left(0\right)}-\eta }{\kappa }\big)+{\rho }^{4}=0\). The physical requirement \({A}_{{{{{\mathrm{1,2}}}}}}^{(\pm )}{\mathfrak{\in }}{\mathfrak{R}}{\mathfrak{(}}{A}_{n}{\mathfrak{\in }}{\mathfrak{R}}{\mathfrak{)}}\) leads to the condition \({\gamma }_{1}^{(0)}-{\gamma }_{2}^{\left(0\right)}-2\eta \ge 0\) (\({\gamma }_{1}^{(0)}-\eta -\frac{\kappa \rho }{2}\ge 0\)) which determines the boundary between domains II and III (domains I and III), see Fig. 1b. Finally, the relation \({\kappa }_{{{{{{{\rm{NLEPD}}}}}}}}={\gamma }_{1}^{(0)}+{\gamma }_{2}^{(0)}\) defines the transition between domains I and II—which is characterized by the formation of a NLEPD associated with the coalescence of two stable NS (see solid red line in Fig. 1b). This is further confirmed by evaluating the nonlinear eigenfrequencies f±(κ) associated with the solutions of Eq. (2). From the TCMT, we have that (see Supplementary Note 4a, b):
where the square-root dependence of the eigenfrequencies from the coupling detuning κ reflects the presence of the NLEPD. In the range of voltage variations that have been used in our experiment (−1.1 V ≤ δV ≤ 2 V with resolution of 1 mV), the coupling is κ(δV) ≈ κNLEPD − (0.0234 V−1)⋅δV with \({\kappa }_{{{{{{{\rm{NLEPD}}}}}}}}\equiv {\gamma }_{1}^{\left(0\right)}+{\gamma }_{2}^{\left(0\right)}\, \approx \, 0.30\) (where \({\gamma }_{1}^{\left(0\right)}\, \approx \, 0.18;{\gamma }_{2}^{\left(0\right)}\, \approx \, 0.12\)).
The two fixed points in domain II (κ ≥ κNLEPD), are associated with the AD phase where the field amplitudes at each resonator are the same and the two stable NS differ only by the relative phase φ± (see Supplementary Note 4a). In this parameter range, the system respects an exact parity-time symmetry—where both the system and the corresponding NS are invariant under a joint parity (i.e., space inversion 1 ↔ 2) and time-reversal (i.e., complex conjugation) symmetry. In domain I (κ ≤ κNLEPD), instead, there is only one non-trivial stable NS. This domain is associated with the OD phase where the field amplitudes at each RLC resonator differ from one another. A detailed fixed point numerical analysis using a MATLAB fsolve routine confirms the above theoretical predictions and provides more general information about other (unstable) fixed points, as well as the stability analysis of the nontrivial NS via the eigenvalues of the Jacobian (see Fig. 2a, b). In the inset of Fig. 2b, we also report some represented values of the measured voltage ratios \(\frac{{V}_{1}}{{V}_{2}}\) versus the voltage variation δV. These results compare nicely with the TCMT predictions (black line) indicating that the NLEPD occurs at the transition between AD and OD phases. The slight deviations for large negative δV are attributed to the small detunings of various components in our circuit from its ideal (TCMT) parameters (see Supplementary Note 7 and Supplementary Fig. 4) and to the limitations of the TCMT. The applicability of the latter is subject to a number of approximations: high-Q factors of each RLC resonator, weak coupling between the two RLC tanks, and the elimination of fast-oscillating terms (see Supplementary Note 1). Nevertheless, the overall agreement between the predictions of TCMT, the NGSPICE simulations (blue solid line) and the experimental results are satisfactory. Additionally, the TCMT predicts that the voltage contrast follows a Puiseux expansion, \(\frac{{V}_{1}}{{V}_{2}}\approx 1+|\delta {{V|}}^{\frac{2}{3}}+O(|\delta {{V|}}^{\frac{4}{3}})\), resulting in \(\log \left(\frac{{V}_{1}}{{V}_{2}}\right) \sim |\delta {{V|}}^{\frac{2}{3}}\). This sublinear response of the voltage contrast suggests that it could also be used as another physical observable for sensing purposes. Further analysis on the SNE of such observable is necessary to establish it as sensing measurand and will be reported elsewhere.
The existence of a stable NS does not guarantee the evolution of the system to this specific state. Instead, the system may evolve either to a stable trivial state, or to another stable NS in case of bistabilities (AD domain). The former scenario is easily excluded by an appropriate choice of the relative gain parameter (see Fig. 1b). The latter scenario can be controlled by realizing that the final state depends strongly on the initial conditions {A1(0), A2(0), φ(0)} (see Supplementary Note 6). The phase-space volume that contains the initial conditions which converge to a specific stable fixed point constitute a basin of attraction, and its size provides a measure of how attractive this fixed point is. Detailed dynamical simulations using Eq. (1)—for various κ values along with a fine mesh of initial conditions {A1, A2, φ}—allowed us to identify the basins of attraction of the two fixed points in the AD domain. We find that initial excitations with a relative phase \(\left|\varphi \right|\, > \, \frac{\pi }{2}\) end up at the AD fixed point associated with the f− mode while an initial preparation with a phase \(\left|\varphi \right|\, < \, \frac{\pi }{2}\) leads to a f+ supermode. In Fig. 2c, we show the basins of attraction for the f+(f−) fixed points which are indicated with blue (yellow) color for the example case of δκ ≡ κ(δV) − κNLEPD ≈ 5 ⋅ 10−5 (corresponding to δV ≈ 2 mV). In fact, further analysis using TCMT indicated that a small detuning between the resonant frequencies of the two RLC resonators smoothens the frequency splitting in the close proximity of the NLEPD without drastically affecting the square-root response of f+. At the same time, it has important consequences on the stability of the NS in the vicinity of the NLEPD by favoring only the upper branch f+ which remains stable—as opposed to the lower branch f− that turns unstable (see Supplementary Note 7 and Supplementary Fig. 4). Away from the NLEPD the bistable nature at the AD domain persists. Either way, the square-root scaling of the NS frequency f+ from fNLEPD (see Eq. (3)) is unaffected.
Sensing protocol
In Fig. 3a, we report a density-plot of the voltage power spectrum |V1(ω)|2 for various voltage variations δV by performing a Fourier transform of the temporal field—which were evaluated via time-domain simulations of the TCMT Eq. (1). To achieve the asymptotic states associated with the f+(f−) supermodes in the AD domain, we have prepared the initial excitation at relative phase \(\left|\varphi \right| < \frac{\pi }{2}(\left|\varphi \right| > \frac{\pi }{2})\) as discussed above. The numerical data agree nicely with the theoretical predictions of Eq. (3). In Fig. 3b, we show a density plot of the measured power spectrum of the emitted signal together with the TCMT predictions of Eq. (3) for the f+ frequency (red dashed line). The absence of f− from the measured power spectrum, is associated with the fact that the experimental initial preparation favors a field excitation with a small relative phase \(\left|\varphi \right| < \frac{\pi }{2}\). In the same figure, we also report the f+ frequency (versus δV) that has been extracted by a Fourier transform of the voltage V1(t) using NGSPICE simulations (black dotted line).
The sublinear detuning is better appreciated by reporting Δf+ ≡ f+ − fNLEPD versus δV in a double-logarithmic plot. The experimental data (cyan circles) nicely match the results from the NGSPICE (dashed black line) showing the predicted behavior \(\varDelta {f}_{\!\!+}\propto \sqrt{\delta V}\) from TCMT, see Fig. 3c. This sublinear response offers an opportunity to develop an enhanced sensing protocol for detecting small voltage variations, δV, using the coupling capacitor Cκ(δV) as a sensing platform. At the same time, the square-root SLR extends the dynamical range (DR) of the sensing measurements up to relatively large values of δV. The DR is the other important metric that characterizes the efficiency of a sensor, and it is defined as the ratio between the maximum and the minimum δV variation that the sensor can measure. Furthermore, the presence of gain elements guarantees the narrowing of the emission peaks and promotes an enhanced resolution. To further quantify the efficiency of our sensing protocol, we have introduced the sensitivity, \(\chi \equiv \frac{\partial \big(\frac{\varDelta f}{{f}_{0}}\big)}{\partial \left(\delta V\right)}\). In Fig. 3d we report the measured sensitivity (violet circles) together with the NGSPICE results (black dashed line). We find that, within the experimental resolution, \(\chi \sim \frac{1}{\sqrt{\delta V}}\) in the proximity of the NLEPD. Obviously, the frequency smoothening of Δf+ around the NLEPD (see Fig. 3b), whose origin is traced back to small unavoidable resonant mismatch between the resonances of the two RLC tanks (see Supplementary Note 7 and Supplementary Fig. 4), will eventually set a saturation value for the sensitivity.
Noise analysis
The sublinear frequency detuning Eq. (3) guarantees an enhanced transduction function from the voltage variation to the sensitivity χ. However, it does not, address another important characteristic of high-performance sensors that is related to the precision of the measurements. The latter is identified with the smallest measurable variation in the input signal that can be identified by the sensor due to noise at the output signal.
To better understand the effects of noise in the measurement process, we have analyzed the Allan deviation, \({\sigma }_{{\widetilde{\varDelta f}}_{+}}(\tau )\), of the normalized frequency detunings, \({\widetilde{\varDelta f}}_{+}\equiv \frac{\varDelta {f}_{+}}{{f}_{0}}\), as a function of the sampling time τ42,43. The measured Allan deviation is reported in Fig. 4a for representative δV values—both well within the NLEPD-enhanced sensitivity regime and away from it. We observe that as δV decreases, and the system approaches towards the NLEPD, the noise increases. To better appreciate the effects of noise in the measured voltage variation, we report in Fig. 4b the normalized Allan deviation, \({\sigma }_{\alpha }\left(\tau \right)={\sigma }_{{\widetilde{\varDelta f}}_{+}}\left(\tau \right)/\chi \,\, [V]\). Our measurements show that the noise grows slower than the signal enhancement as we are approaching the NLEPD. Therefore, we conclude that the proposed protocol can provide an enhanced SNR in the proximity of a NLEPD. Based on the behavior of Allan deviation, we can distinguish different regimes depending on the duration of the sampling time τ. Each regime is influenced by a different type of noise source. At the limiting case of long sampling times, the Allan deviation behaves as \({\sigma }_{\alpha }^{{{{{{{\rm{DRR}}}}}}}}={\alpha }_{{{{{{{\rm{DRR}}}}}}}}\tau .\) This is typical of a drift rate ramp (DRR) noise associated with the presence of systematic (deterministic) errors. For intermediate sampling times, the Allan deviation reaches a saturation value \({\sigma }_{\alpha }^{{{{{{{\rm{BI}}}}}}}}\left(\tau \right)={\alpha }_{{{{{{{\rm{BI}}}}}}}}{\tau }^{0}\), which is indicative of the bias instability (BI) noise. The value of αBI sets the smallest possible reading of our sensor. Its origin is traced to the random flickering of electronics or other components of the system. Finally, the short-time behavior of Allan deviation exhibits voltage (variations) random walk (VRW) noise which decreases with the sampling time τ as \({\sigma }_{\alpha }^{{{{{{{\rm{VRW}}}}}}}}={\alpha }_{{{{{{{\rm{VRW}}}}}}}}\cdot {\tau }^{-1/2}\). The origin of the VRW is traced to noise sources, such as thermal (Johnson-Nyquist) noise from the circuit elements (resistors and the amplifier) and attached TLs; the readout noise; and other noise sources associated with fluctuations of the voltage applied to the coupling capacitor or fluctuations of the capacitance due to thermal variations. Each of them is described by a separate noise coefficient αcir, αTL, αdet, αadd, respectively, and contributes to the noise equivalent voltage variation given by \({\alpha }_{{{{{{{\rm{VRW}}}}}}}}=\sqrt{{\alpha }_{{{{{{{\rm{JN}}}}}}}}^{2}+{\alpha }_{\det }^{2}+{\alpha }_{{{{{{{\rm{add}}}}}}}}^{2}}\), where \({\alpha }_{{{{{{{\rm{JN}}}}}}}}^{2}={\alpha }_{{{{{{{\rm{cir}}}}}}}}^{2}+{\alpha }_{{{{{{{\rm{TL}}}}}}}}^{2}\). Since αdet can be actively minimized, the thermal noise, αJN, together with αadd, represent the best obtainable limit for αVRW.
In Fig. 4c, we provide a panorama of αVRW for all δV-values that we have used in our measurements (blue circles). From the measurements, we conclude that \({\alpha }_{{{{{{{\rm{VRW}}}}}}}}\approx 0.002\,\delta {V}^{0.5}[{{Vs}}^{\frac{1}{2}}]\), indicating a robustness to the VRW noise, which is attributed to the stable hyperbolic nature of the f+ supermode. Specifically, the phase-space around these hyperbolic fixed points are structurally stable41, and the associated basin of attraction is relatively broad—even for voltage variations close to the NLEPD (see Fig. 2c). Therefore, the VRW noise is not able to significantly push the phase-space trajectories out of the basin of attraction. In the same figure, we also show the noise coefficient αJN from NGSPICE (red diamonds), where we have incorporated thermal noise at the resistors, the amplifier, and the TLs described by an ambient temperature of T = 300 K. The simulated value of αJN is over an order of magnitude smaller than our experimental measurements for αVRW. We conclude that the detection noise αdet combined with αadd overwhelms the thermal noise αJN. Eventually, the absolute bound of αVRW will be determined by the noise due to coupling fluctuations that originate from applied voltage uncertainties and temperature-dependent capacitive effects.
Discussion
We have demonstrated a SNE sensing of an NLEPD-based voltmeter. The proposed sensing protocol is based on a square-root frequency detuning from the NLEPD induced by a small voltage variation that modifies the coupling between two nonlinear RLC tanks. The NLEPD occurs at the transition between two types of oscillation quenching regimes, i.e., OD and AD domains, in the parameter space, which are consequences of the nonlinear gain/loss channels assigned to each RLC tank. The underlying phase space is structurally stable in the proximity of the (stable) fixed points associated with the degenerate NS, while the corresponding basins of attraction are relatively broad, even for voltage variations that are close to the NLEPD. These characteristics, shield the sensing signal from noise resulting in a two orders of magnitude enhancement of signal-to-noise ratio in the proximity of the NLEPD. Our results establish EPD-sensing from self-oscillating systems as an efficient platform with a dramatically improved SNE factor in the proximity of the NLEPD. Our scheme can guide the design of oscillation quenching-based hypersensitive sensors with enhanced dynamical range that can be utilized in electroencephalography, electrocardiography and neuroprosthetics. Other applications that can utilize the current design include sensitive manometers, flow sensors, accelerometers, inclinometers for telemetry44 and implantable microsensors45. Many of these applications could also be realized in other frameworks, such as photonics, where circuits with neuromorphic functionalities have already been reported46.
Let us finally point out that while the specific form of the nonlinearity used in our design leads to an enhanced signal-to-noise ratio in the proximity of the NLEPD, this is not necessarily the case for just any self-oscillating system. For example, in refs. 13,16, the EPD-based Brillouin ring-laser gyroscope was found to enhance the noise in the proximity of the EPD, offsetting the enhancement in sensitivity. In this respect, it will be interesting to extend the current investigation of SNE sensing schemes to other self-oscillating systems whose nonlinear nature allows for the presence of limit cycles and Hopf bifurcations47. Sublinear sensing protocols based on nonlinear mechanisms are a promising direction for building hypersensitive SNE sensors. For example, a recent theoretical proposal that advocates for SNE48 utilizes sublinear intensity variations due to a dynamic hysteresis occurring in nonlinear resonators. Its experimental implementation, however, could be problematic for fast sensing purposes, since it requires up-down sweeping of a control parameter which can be time-consuming. Further exciting future research includes the identification of other physical observables, such as scattering cross-section anomalies (e.g., Wigner cusps)49,50 and transmission peak degeneracies15, whose sublinear response for sensing purposes has thus far been utilized in linear settings.
Methods
Circuit design and fabrication
The circuit schematic used for this experiment can be seen in Supplementary Fig. 1. It features two RLC resonators which are coupled to each other via voltage-controlled capacitors. The main elements that make up each RLC resonator are a resistor, Ri, an inductor, Li, and a pair of in-parallel grounded capacitors, Cv and Ci, where i = 1,2, denotes the gain and loss RLC units, respectively. The inductors, Li = 200 μH, used in both the gain and loss resonators are API Delevan 807-1537-90HTR. The total capacitance in each resonator is made up by a combination of a tunable capacitor, Cv, connected in parallel with a fixed capacitor, Ci. The tunable capacitor, Cv, is a Murata 81-LXRW19V201-058 with a capacitance range of 100–200 pF. A voltage of 0.5 V was applied to the tunable capacitor in each RLC resonator, and it was controlled by a EG&G Instruments 7265 DSP lock-in amplifier, that was connected via a Bayonet Neill–Concelman (BNC) port to a resistor, Rv, model Yageo 603-RC0402FR-074K99L, with a resistance of Rv = 4.99 kΩ. This resistor was connected to a grounded fixed capacitor, Cv1, a Murata 81-GCM32EL8EH106KA7L, with a capacitance of Cv1 = 10 μF. The fixed capacitors in each resonator unit, Ci, is a Kemet 80-C0603C911F5G with a capacitance of 910 pF. This gives a total capacitance in each RLC resonator of 200 pF + 910 pF = 1110 pF.
Each RLC resonator has resistive elements that collectively provide gain and loss. The former is provided by an operational amplifier (op-amp) model Analog Devices 584-ADA4862-3YRZ-R7. The power supply for the op-amp was connected by a standard 3 pin connector, with one going to ground, and the other two being connected to V+ = 6 V and V− = −6 V, respectively. To produce gain, the op-amp has a pair of internal resistances, RG1 and RG2, of 550 Ω each. RG1 is connected in between the output of the op-amp and the inverting input of the op-amp. RG2 is connected on one end to the inverting input of the op-amp and, grounded on the other end. The mechanically tunable variable resistor in the gain RLC tank, R1, is a Vishay 71-PHPA1206E2001BST1 component that has a resistance of R1 = 2000 Ω. R1 is connected on one end to the operational amplifier’s non-inverting input. The other end of R1 is connected to a capacitor, Ce1, model Kemet 80-C0805C100FDTACTU where Ce1 = 10 pF, capacitively couples each RLC resonator to transmission lines. A mechanically tunable variable resistor, RT1, is connected in parallel to R1, and the op-amp, is a Bourns 652-3269W-1-102GLF with RTi = 720 ± 200 Ω. The set value of RT1 = 720 Ω, and it is connected to a pair of grounded back-to-back of diodes, Di, Onsemi 512-1N914BWS—which represent the nonlinear elements of this RLC dimer. The fixed resistor in the loss resonator, R2, is a Vishay 71-PCNM2512E2501BST5 component with a resistance of R2 = 2500 Ω. R2 is connected in parallel to RT2 = 750 Ω. On the other end, RT2 is connected to a pair of back-to-back grounded diodes—the same model of diodes as in the gain resonator was used.
The coupling between the two resonators was achieved using two parallel variable capacitors, Cvc. The component used in Cv, a Murata 81-LXRW19V201-058 is the same model as the variable capacitors in the resonator units, Cvc. As in the RLC tanks, Cvc is connected to a grounded Cv1 which in turn is connected to Rv. The same lock-in amplifier is used to control the tuning voltage via a BNC port. One of the two capacitors is held fixed at 200 pF with a constant applied voltage of 0.5 V, whereas the other is tuned in voltage range between 0.4 and 3.5 V.
Voltage and frequency detuning measurements
The emitted signal from the electronic circuit was collected for different applied voltage variations of the capacitance voltage control (CVC) capacitor. These voltage variations where electronically controlled via an EG&G Instruments 7265 DSP lock-in amplifier. The imposed voltage variations were in the range between 0.4 and 3.5 V associated with −1.1 V ≤ δV ≤ 2 V with resolution of up to 1 mV. At each specific voltage variation, the emitted spectrum was collected using a network analyzer Keysight E5080A. The individual frequency sweeps contain 4001 points in a range of 295–320 kHz. A single measurement was obtained from the collected spectrum with an intermediate frequency bandwidth (IFBW) of 100 Hz giving a sampling time of 40.01 s. The peak frequencies of the spectrum f+ were then identified from the resulted spectrum, which allows the calculation of the frequency detuning Δf+.
Allan deviation measurement
The Allan deviation \({\sigma }_{{\widetilde{\Delta f}}_{\!\!+}}(\tau )\) of the frequency associated with the voltage power spectrum peak of the emitted signal is defined as
where τ is the sampling time, M is the total number of frequency measurements and \(\langle {\widetilde{\varDelta f}}_{\!\!+}^{\left(n\right)}\rangle\) indicates the average rescaled frequency detuning during the sampling time interval [nτ,(n + 1)τ]. For the extraction of Allan deviation, the rescaled emitted peak detunings \({\widetilde{\varDelta f}}_{\!\!+}\equiv \frac{\varDelta {f}_{+}}{{f}_{0}}\) were sampled with an IFBW of 10 kHz for 101 points in a frequency range of 7 kHz centered around the expected Δf+ for the associated δV. Twenty thousand consecutive spectral measurements were performed over a period of approximately 2700 s for each δV. This results in a sampling time of 0.1337 s.
NGSPICE simulations
We use NGSPICE, an open-source software for electronic circuits, to simulate the dynamical behavior of our experimental platform. We consider two RLC tanks coupled by a capacitor using the same characteristics as the experimental platform, where, unless specified otherwise, uses the same parameters of the electronic components described in “Circuit Design and Fabrication” sub-section of “Methods.” The op-amp in the gain resonator is represented by a high impedance Norton amplifier by designating its constituent components—a transconductance that quantifies gain, a capacitor and diode clippers. Nonlinearity in the gain and loss resonators is modeled with back-to-back diodes via 1N914 diodes—the same type as used in the experimental platform—using the appropriate parameters that describe its behavior. To compensate for the detuning due to the capacitor in the op-amp, the capacitor in the gain resonator, Cv + C1, was detuned slightly to 0.9955(Cv + C1), to fit the experimental data obtained. In conjunction with that Li (i = 1,2) was set at 0.965Li, in the simulations. Using this setup, we evaluate the signal generated by the circuit for a total time of \(t=\frac{6000}{{f}_{0}}\, \approx \, 0.017\,{{{{{\rm{s}}}}}}\) with the time steps of \(dt=\frac{1}{({80f}_{0})}\, \approx \, 37\,{{{{{{\rm{ns}}}}}}}\). In our analysis of the power spectrum, we dropped the first 0.0017 s, which correspond to the short time transient, to consider only the steady-state behavior.
To add noise, we modeled Johnson–Nyquist noise—electronic noise due to thermal fluctuations. This was added to our simulations by adding random voltage sources at every resistor in our circuit (including the TLs). The amount of noise added at each resistor using the TRNOISE function of NGSPICE at these resistors are dictated by the root mean square of the voltage due to Johnson–Nyquist noise. This is given by \({v}_{{{{{{{\rm{rms}}}}}}}}=\sqrt{4{k}_{{{{{{\rm{B}}}}}}}{{{{{{\rm{TRB}}}}}}}}\) where kB is Boltzmann’s constant; R is the value of the respective resistor at which the random voltage source was added; B is the bandwidth of the noise for which the natural frequency of the resonator ≈ 338 kHz was assumed; and T is the temperature for which the ambient value of 300 K was chosen.
Data availability
The datasets generated during and/or analyzed during the current study are available in the Zenodo repository51 (https://doi.org/10.5281/zenodo.8250657).
Code availability
The codes for reproducing TCMT data are deposited at the Zenodo repository51 (https://doi.org/10.5281/zenodo.8250657).
References
Kato, T. Perturbation Theory for Linear Operators (Springer Berlin/Heidelberg, 1995).
Ma, Y. & Edelman, A. Nongeneric eigenvalue perturbations of Jordan blocks. Linear Algebra Appl. 273, 45–63 (1998).
Moiseyev, G. N. Non-Hermitian Quantum Mechanics (Cambridge Univ. Press, 2011).
Bender, C. M. PT Symmetry in Quantum and Classical Physics (World Scientific, 2018).
El-Ganainy, R. et al. Non-Hermitian physics and PT symmetry. Nat. Phys. 14, 11–19 (2018).
Feng, L., El-Ganainy, R. & Ge, L. Non-Hermitian photonics based on parity–time symmetry. Nat. Photonics 11, 752–762 (2017).
Özdemir, Ş. K. et al. Parity–time symmetry and exceptional points in photonics. Nat. Mater. 18, 783–798 (2019).
Miri, M.-A. & Alu, A. Exceptional points in optics and photonics. Science 363, eaar7709 (2019).
Wiersig, J. Enhancing the sensitivity of frequency and energy splitting detection by using exceptional points: application to microcavity sensors for single-particle detection. Phys. Rev. Lett. 112, 203901 (2014).
Hodaei, H. et al. Enhanced sensitivity at higher-order exceptional points. Nature 548, 187–191 (2017).
Chen, W. et al. Exceptional points enhance sensing in an optical microcavity. Nature 548, 192–196 (2017).
Hokmabadi, M. P. et al. Non-Hermitian ring laser gyroscopes with enhanced Sagnac sensitivity. Nature 576, 70–74 (2019).
Lai, Y. H. et al. Observation of the exceptional-point-enhanced Sagnac effect. Nature 576, 65–69 (2019).
Wiersig, J. Prospects and fundamental limits in exceptional point-based sensing. Nat. Commun. 11, 2454 (2020).
Kononchuk, R. et al. Exceptional-point-based accelerometers with enhanced signal-to-noise ratio. Nature 607, 697–702 (2022).
Wang, H. et al. Petermann-factor sensitivity limit near an exceptional point in a Brillouin ring laser gyroscope. Nat. Commun. 11, 1610 (2020).
Lau, H. K. & Clerk, A. A. Fundamental limits and non-reciprocal approaches in non-Hermitian quantum sensing. Nat. Commun. 9, 4320 (2018).
Langbein, W. No exceptional precision of exceptional-point sensors. Phys. Rev. A 98, 023805 (2018).
Wiersig, J. Robustness of exceptional point-based sensors against parametric noise: the role of Hamiltonian and Liouvillian degeneracies. Phys. Rev. A 101, 053846 (2020).
Petermann, K. Calculated spontaneous emission factor for double-heterostructure injection lasers with gain-induced waveguiding. IEEE J. Quantum Electron. 15, 566 (1979).
Siegman, A. E. Excess spontaneous emission in non-Hermitian optical systems. I. Laser amplifiers. Phys. Rev. A 39, 1253 (1989).
Goldberg, P., Milonni, P. W. & Sundaram, B. Theory of the fundamental laser linewidth. Phys. Rev. A 44, 1969 (1991).
Kuznetsov, Y. A. Elements of Applied Bifurcation Theory (Applied Mathematical Sciences, 112) (Springer, 2013).
Kominis, Y., Kovanis, V. & Bountis, T. Spectral signatures of exceptional points and bifurcations in the fundamental active photonic dimer. Phys. Rev. A 96, 053837 (2017).
Zhiyenbayev, Y., Kominis, Y., Valagiannopoulos, C., Kovanis, V. & Bountis, A. Enhanced stability, bistability and exceptional points in saturable active photonic couplers. Phys. Rev. A 100, 043834 (2019).
Yu, S., Piao, X. & Park, N. Neuromorphic functions of light in parity-time-symmetric systems. Adv. Sci. 6, 1900771 (2019).
Yu, S., Piao, X. & Park, N. Topologically protected optical signal processing using parity-time-symmetric oscillation quenching. Nanophotonics 10, 2883 (2021).
Buzsáki, G. Rhythms of the Brain (Oxford Univ. Press, 2006)
Saxena, G., Prasad, A. & Ramaswamy, R. Amplitude death: the emergence of stationarity in coupled nonlinear systems. Phys. Rep. 521, 205–228 (2012).
Koseska, A., Volkov, E. & Kurths, J. Oscillation quenching mechanisms: amplitude vs. oscillation death. Phys. Rep. 531, 173–199 (2013).
Choi, S., Kim, J., Kwak, J., Park, N. & Yu, S. Topologically protected all-optical memory. Adv. Electron. Mater. 8, 2200579 (2022).
Hassan, A. U., Hodaei, H., Miri, M.-A., Khajavikhan, M. & Christodoulides, D. N. Nonlinear reversal of the PT-symmetric phase transition in a system of coupled semiconductor microring resonators. Phys. Rev. A 92, 063807 (2015).
Ge, L. & El-Ganainy, R. Nonlinear modal interactions in parity-time (PT) symmetric lasers. Sci. Rep. 6, 24889 (2016).
Kominis, Y., Choquette, K. D., Bountis, A. & Kovanis, V. Exceptional points in two dissimilar coupled diode lasers. Appl. Phys. Lett. 113, 081103 (2018).
Zhu, B., Wang, Q. J. & Chong, Y. D. Laser-mode bifurcations induced by PT-breaking exceptional points. Phys. Rev. A 99, 033829 (2019).
Benzaouia, M., Stone, A. D. & Johnson, S. G. nonlinear exceptional-point lasing with ab initio Maxwell-Bloch theory. APL Photonics 7, 121303 (2022).
Lin, Z., Schindler, J., Ellis, F. M. & Kottos, T. Experimental observation of the dual behavior of PT-symmetric scattering. Phys. Rev. A 85, 50101 (2012).
Bender, N. et al. Observation of asymmetric transport in structures with active nonlinearities. Phys. Rev. Lett. 110, 1 (2013).
Lee, J. M. et al. Reconfigurable directional lasing modes in cavities with generalized PT-symmetry. Phys. Rev. Lett. 112, 253902 (2014).
Chitsazi, M. et al. Experimental observation of lasing shutdown via asymmetric gain. Phys. Rev. A 89, 43842 (2014).
Hartman, P. On the local linearization of differential equations. Proc. Am. Math. Soc. 14, 568–573 (1963).
El-Sheimy, N., Hou, H. & Niu, X. Analysis and modeling of inertial sensors using Allan variance. IEEE Trans. Instrum. Meas. 57, 140–149 (2008).
Quinchia, A. G., Falco, G., Falletti, E., Dovis, F. & Ferrer, C. A comparison between different error modeling of MEMS applied to GPS/INS integrated systems. Sensors 13, 9549–9588 (2013).
Chen, P. Y. et al. Generalized parity–time symmetry condition for enhanced sensor telemetry. Nat. Electron. 1, 297–304 (2018).
Dong, Z. et al. Sensitive readout of implantable microsensors using a wireless system locked to an exceptional point. Nat. Electron. 2, 335–342 (2019).
Prucnal, P. R. & Shastri, B. J. Neuromorphic Photonics (CRC Press, 2017).
Valagiannopoulos, C. & Kovanis, V. Injection-locked photonic oscillators: legacy results and future applications. IEEE Antennas Propag. Mag. 63, 51–59 (2021).
Peters, K. J. H. & Rodriguez, S. R. K. Exceptional precision of a nonlinear optical sensor at a square-root singularity. Phys. Rev. Lett. 129, 013901 (2022).
Tuxbury, W., Kononchuk, R. & Kottos, T. Non-resonant exceptional points as enablers of noise-resilient sensors. Commun. Phys. 5, 210 (2022).
Kononchuk, R., Knee, J., Feinberg, J. & Kottos, T. Enhanced avionic sensing based on Wigner’s cusp anomalies. Sci. Adv. 7, eabg8118 (2021).
Suntharalingam, A., Fernández-Alcázar, L., Kononchuk, R. & Kottos, T. Data and codes for “Noise resilient exceptional-point voltmeter enabled by oscillation quenching phenomena”. zenodo https://doi.org/10.5281/zenodo.8250656 (2023).
Acknowledgements
A.S., R.K., and T.K. acknowledge partial support from MPS Simons Collaboration via grant No. 733698 and from NSF-CMMI-1925543. A.S. and T.K. also acknowledges partial support from grant NSF ECCS 2148318, which is supported in part by funds from OUSD R&E, NIST, and industry partners as specified in the Resilient & Intelligent NextG Systems (RINGS) program. L.F.-A. acknowledges support by CONICET Grant No. PIP2021 (11220200100170CO). We acknowledge useful discussions with Professor U. Kuhl on improvements of noise analysis, Professor F. Ellis on circuit design and Mr. W. Tuxbury for assisting with the experimental platform. We also acknowledge useful discussions with Professor G. Aaron and Professor K. Perks on neuronal functionalities.
Author information
Authors and Affiliations
Contributions
A.S. and R.K. designed and fabricated the electronic circuit. A.S. and R.K. characterized the electronic circuit and performed the experimental measurements. A.S. and L.F.-A. developed the theory and carried out simulations and data analysis. T.K. formulated the project. All authors discussed the results. A.S., L.F.-A., and T.K. wrote the manuscript with input from R.K.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Vassilios Kovanis, Sunkyu Yu, and the other anonymous reviewers for their contribution to the peer review of this work. A peer review file is available.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Suntharalingam, A., Fernández-Alcázar, L., Kononchuk, R. et al. Noise resilient exceptional-point voltmeters enabled by oscillation quenching phenomena. Nat Commun 14, 5515 (2023). https://doi.org/10.1038/s41467-023-41189-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-023-41189-7
- Springer Nature Limited
This article is cited by
-
Chiral transmission by an open evolution trajectory in a non-Hermitian system
Light: Science & Applications (2024)
-
Enhanced sensitivity with nonlinearity-induced exceptional points degeneracy lifting
Communications Physics (2024)
-
Observation of continuum Landau modes in non-Hermitian electric circuits
Nature Communications (2024)