Abstract
Optical parametric oscillation (OPO) is distinguished by its wavelength access, that is, the ability to flexibly generate coherent light at wavelengths that are dramatically different from the pump laser, and in principle bounded solely by energy conservation between the input pump field and the output signal/idler fields. As society adopts advanced tools in quantum information science, metrology, and sensing, microchip OPO may provide an important path for accessing relevant wavelengths. However, a practical source of coherent light should additionally have high conversion efficiency and high output power. Here, we demonstrate a silicon photonics OPO device with unprecedented performance. Our OPO device, based on the third-order (χ(3)) nonlinearity in a silicon nitride microresonator, produces output signal and idler fields widely separated from each other in frequency ( > 150 THz), and exhibits a pump-to-idler conversion efficiency up to 29 % with a corresponding output idler power of > 18 mW on-chip. This performance is achieved by suppressing competitive processes and by strongly overcoupling the output light. This methodology can be readily applied to existing silicon photonics platforms with heterogeneously-integrated pump lasers, enabling flexible coherent light generation across a broad range of wavelengths with high output power and efficiency.
Similar content being viewed by others
Introduction
Many applications in quantum information science, metrology, and sensing require access to coherent laser light at a variety of wavelengths, ideally in a chip-integrated format suitable for scalable fabrication and deployment. While integrated photonics lasers are highly developed in the telecommunications band1, many of the aforementioned technologies operate at other wavelengths. To this end, the extension of heterogeneously integrated lasers to other bands has been pursued, with recent demonstrations at 980 nm2,3 and 2000 nm4. However, wavelength access across the entirety of a broad spectral range would demand the challenging integration of several material platforms. In contrast, table-top nonlinear optics5,6 is widely used to produce coherent light at wavelengths that are difficult to access through direct laser emission. Processes such as optical harmonic generation, stimulated four-wave mixing, and optical parametric oscillation enable the spectral translation and/or generation of coherent light at wavelength(s) that can differ dramatically from those at the input. The development of high-performance nonlinear integrated photonics platforms7, when combined with compact lasers, may provide a compelling approach for realizing flexible wavelength access on-chip.
Here, we demonstrate high-performance χ(3) OPO on a silicon microchip. By suppressing competing nonlinear processes that would otherwise saturate parametric gain and by strongly overcoupling the output mode while retaining high overall Q, we simultaneously realize wide spectral separation between the participating modes (signal-idler separation > 150 THz), high conversion efficiency (up to ≈ 29%), and useful output power (up to ≈ 21 mW), a compelling combination of properties that, to the best of our knowledge, has not previously been simultaneously achieved in on-chip OPO. Our work highlights the potential of OPO in silicon photonics to address many requirements for deployable laser technologies in scientific applications, particularly in light of recent progress on heterogeneous integration of III-V lasers and silicon nonlinear photonics8.
Requirements for high performance
In a χ(3) OPO, pump photons at νp are converted to up-shifted signal photons (νs, with νs > νp) and down-shifted idler photons (νi, with νi < νp) that satisfy energy conservation (2νp = νs + νi). Appreciable conversion efficiency requires phase-matching, so that 2βp = βs + βi where βp,s,i, is the propagation constant for the pump, signal, and idler modes, respectively. In microring resonators, which have periodic boundary conditions, this phase relationship can be recast as 2mp = ms + mi where mp,s,i denotes the azimuthal mode order of the pump, signal, and idler modes, respectively. Finally, OPO has a power threshold, meaning that the cavity modes must have sufficiently low loss rates (high loaded Qs) that can be exceeded by the available parametric gain.
While phase- and frequency-matching and high-Q are baseline requirements for OPO, additional requirements are imposed if high-performance OPO is to be achieved. With respect to performance, we focus on the output power and conversion efficiency of wide-bandwidth (signal-idler separation) OPO as our main metrics. Another typical OPO metric is its threshold pump power. While threshold can be important in terms of quantifying resonant enhancement of the nonlinear process, it has a less direct impact on many applications, where the most relevant pump power is determined by the desired output power. To achieve high-performance OPO based on these metrics, first, it is necessary to suppress competitive nonlinear processes that, for example, divert pump energy to the creation of frequency components other than the targeted signal and idler frequencies (Fig. 1(a, b)). In addition, to maximize the conversion efficiency for the output field of interest, optimization of the pump injection into the microring and output extraction from the microring is needed (Fig. 1(c)). We discuss each of these items below, starting with resonator-waveguide coupling.
Increasing the maximum conversion efficiency
The conversion efficiency for the signal (or idler) is dependent on the coupling regime (e.g., overcoupled/undercoupled) of both the signal (or idler) and the pump9,10. As a starting point, we consider a simplified three-mode model in which only the pump, signal, and idler modes are allowed to interact, from which the system’s maximum conversion efficiency, \({\eta }_{s,i}^{{{{{\mathrm{max}}}}}}\equiv {N}_{s,i}/{N}_{p}\) can be derived9. Here, Np is the flux of pump photons at the input of the waveguide and Ns,i is flux of signal or idler photons at the output of the waveguide. The maximum conversion efficiency, \({\eta }_{s,i}^{{{{{{\mathrm{max}}}}}}}\), will occur when the Kerr-shifted modes are perfectly phase- and frequency-matched, and can be written in terms of the coupling parameter Kp,s,i of each resonance as:
where Kp,s,i = κ(p, s, i),ext/κ(p, s, i),int and κ(p, s, i),(ext, int) is the extrinsic (waveguide coupling) or intrinsic loss rate for the pump, signal, or idler mode (Fig. 1(c)). This equation shows that \({\eta }_{s,i}^{max}\) in a χ(3) OPO increases to a maximum value of 0.5 as Kp,s,i increase without bound. However, strongly overcoupling the resonator decreases the total Q = ν/(κext + κint) of the corresponding cavity mode(s), yielding a less efficient nonlinear enhancement. This can translate into very high threshold powers, which may be unsupportable by compact pump lasers. Therefore, efficient OPO generation via overcoupling requires a resonator with very high intrinsic Qint ≈ ν/κint as a starting point. In recent years, it has been demonstrated that Si3N4 microring resonators, suitable for nonlinear photonics and created by mass-production fabrication techniques, can yield intrinsic Qint > 107 (Ref. 11), suggesting that strong overcoupling can be reached while maintaining high overall Q.
Suppressing parasitic processes
In practice, saturation of OPO usually occurs before \({\eta }_{s,i}^{{{{{{\mathrm{max}}}}}}}\) is reached, especially when imposing the additional requirement of achieving \({\eta }_{s,i}^{{{{{{\mathrm{max}}}}}}}\) with high output power. In OPO, the frequency mismatch Δν = − 2νp + νs + νi between the cold-cavity resonances is compensated by their Kerr shifts, which are pump-power dependent quantities, so that there is a limited range of input powers for which Δν will be small enough for high conversion efficiency to be achieved9,10. Thermorefractive shifts will typically also play a role, and in widely separated OPO the wavelength-dependence of the thermorefractive shifts also becomes meaningful. However, because dispersion is influenced by device geometry12, these effects can be addressed by choosing a geometry that targets a Δν > 0 compatible with the input power range of interest.
A more significant challenge comes from parasitic nonlinear processes that deplete the gain of the desired OPO process (Fig. 1(a, b)). Competitive parasitic nonlinear processes in this system are a consequence of a microring resonator’s many azimuthal spatial modes10, and can be worsened by the presence of higher-order transverse spatial modes (including those of a different polarization). As a result, in widely separated OPO, there can be hundreds of modes that exist between the pump and targeted signal (or idler) mode, which can be populated by processes such as modulational instability and subsequent Kerr comb formation. These processes are detrimental to system efficiency as they divert pump photons away from the targeted three-mode OPO process. The natural way to limit close-to-pump parasitic nonlinear processes is to situate the pump in the normal dispersion regime, so that Kerr shifts lead to a larger amount of frequency mismatch for nearby signal-idler pairs. However, normal dispersion around the pump (i.e., Δν < 0) must be balanced by sufficient higher-order dispersion for the widely separated signal-idler pair of interest to be frequency matched, so that Δν ≈ 0, as in (Fig. 1(a))9,12,13. Moreover, the amount of normal dispersion near the pump is also important, as cross-phase modulation involving the widely separated signal and idler modes can result in nonlinear conversion to unwanted spectral channels near the pump if the amount of normal dispersion is insufficient10. Thus, a dichotomy arises: strong normal dispersion suppresses parasitic process, but strong normal dispersion makes the frequency and phase matching conditions challenging to satisfy.
This problem is circumvented though the use of hybrid-mode OPO (hOPO)14, which phase and frequency matches azimuthal modes from different transverse spatial mode families (Fig. 1(b)). Using this technique, it is possible for each of the pump, signal, and idler bands to have strong normal dispersion, thereby suppressing competitive processes, while maintaining phase and frequency matching for the targeted modes. Hence, through careful design of the resonator’s dispersion, it is possible to isolate the hOPO, taking the many-mode system to the limit where it behaves like the modeled three-mode system, where high output power and high conversion efficiency are simultaneously accessible without sacrificing wavelength access.
Results
Device design, dispersion, and coupling
Our devices were fabricated by Ligentec (certain commercial products or names are identified to foster understanding. Such identification does not constitute recommendation or endorsement by the National Institute of Standards and Technology, nor is it intended to imply that the products or names identified are necessarily the best available for the purpose) through a photonic damascene process11 and consist of an H ≈ 890 nm thick, fully SiO2-clad Si3N4 microring resonator with outer radius of 23 μm and a ring width of RW ≈ 3 μm. Figure 2(a) shows a typical cross-section of a microring, which has an inverted trapezoidal shape, with sidewall angle θ ≈ 16∘ as a result of the reflow step within the damascene process, and whose geometry has been verified through focused ion beam cross-sectional imaging of the devices (see Supplementary Material Fig. S2). Finally, the temperature of the devices was not actively managed; they were passively cooled in an ambient-temperature room.
We first measure the frequency mismatch Δν for phase-matched sets of signal, idler, and pump modes, as shown in Fig. 2(a) (see Methods). We plot Δν as a function of the relative mode number μ, indexed with respect to a pump band mode at 308 THz. We consider two cases, the targeted process in which the idler and pump are from the fundamental transverse electric (TE0) mode family and the signal is from the fundamental transverse magnetic mode (TM0) family (shown in purple), and one in which all three modes are from the TE0 mode family (shown in green), i.e., the more typical single mode family case. In the TE0-TE0-TM0 hOPO scheme, Δν ≈ 0 at frequencies near 390 THz and 226 THz, indicating that we can anticipate an OPO signal and idler pair near these frequencies for an appropriate level of pump laser detuning and Kerr nonlinear shifts to compensate for any non-zero frequency mismatch. In contrast, Δν < 0 at all frequencies for the TE0-TE0-TE0 case, indicating that the widely separated process of interest will not occur for this set of modes. More importantly, these results confirm that the pump is situated in a regime of normal dispersion, which is explicitly validated through the evaluation of the dispersion parameter D for the TE0 and TM0 mode families, where \(D=-\frac{c}{2\pi {\lambda }^{2}}\frac{{\partial }^{2}\beta }{\partial {\nu }^{2}}\). As shown in Fig. 2(b), D < 0 for the TE0 family—not only in the pump band, but also in the idler band (as well as the signal band). In addition, D < 0 for the TM0 family in the signal band. As discussed above, this normal dispersion throughout the entire frequency range between the signal and idler, and in particular surrounding the pump, should suppress many potentially competing nonlinear processes.
We next move to the resonator-waveguide coupling, which, as noted in a previous section, is critical for a high-performance OPO. We focus on conversion efficiency and output power of the idler generated near 1300 nm. From Eq. (1), \({\eta }_{i}^{{{{{{\mathrm{max}}}}}}}\) depends on the coupling parameter for the pump Kp and for the idler Ki, with greater efficiency being achieved with increased Ki and Kp. Additionally, to maintain an acceptable threshold power and because we are not focusing on extraction of the signal, we target small Ks. Using a straight waveguide that is at a gap and tangent to the ring naturally leads to variation in resonator-waveguide coupling across broad spectral ranges, since the modal overlap between ring and waveguide modes depends on the evanescent decay lengths of each mode (Fig. 2(c) inset), which itself depends on wavelength. As a result, long wavelength modes tend to be overcoupled and short wavelength modes tend to be undercoupled15, so that Ki > Kp > Ks as desired, provided that intrinsic quality factors remain high throughout. We note that other possible OPO objectives, such as high efficiency and output power for the signal field, or equal efficiency and output power for both signal and idler fields, may require alternate coupling strategies, such as pulley waveguide couplers15.
Next, we experimentally study Ki, Kp, and Ks for a series of devices in which the resonator-waveguide gap is varied between 200 nm and 500 nm in Fig. 2(c). We observe the expected increase in Ki,p,s with decreasing gap, that Ki > Kp > Ks throughout, and that specific gap values can be chosen to target the high-performance overcoupled regime. For example, Fig. 2(d) shows the cavity mode transmission spectra at a gap of 300 nm. Of note are the high intrinsic quality factors achieved, e.g., Qint ≈ {5.2 × 106, 6.1 × 106, 3.3 × 106} for the signal, pump, and idler bands, respectively. This enables significant overcoupling to be achieved (Ki ≳ 10, Kp ≳ 1) while maintaining high overall Qs. In comparison to other works utilizing resonators of a similar cross-section and size (i.e., an FSR of 1 THz)16, the intrinsic Qs we observe are somewhat higher. This is likely a consequence of the relatively wide 3 μm ring widths we use, which limits the interaction of the optical field with the sidewalls. The ability to use such wide rings is a consequence of the hOPO scheme.
High-performance OPO
We next characterize the hOPO performance of our dispersion- and coupling-engineered microresonators. Figure 3(a) shows the output spectrum when a device with a gap of 300 nm is pumped with Pp = (87.3 ± 3.0) mW of power at a frequency of 308 THz. As parasitic sidebands are suppressed, a well-isolated OPO spectrum with idler at 230 THz and signal at 386 THz is produced with an on-chip idler power of Pi = (13.8 ± 1.1) mW, corresponding to a conversion efficiency (in photon flux) ηi ≈ 0.21 ± 0.03 (the uncertainty values are described in the Fig. 3 caption). In contrast, traditional wide-span single-mode-family OPOs typically start to see the formation of parasitic sidebands at Pi ≈ 1 mW. To elucidate the crucial role of resonator-waveguide coupling in the generation of high \({\eta }_{i}^{{{{{{\mathrm{max}}}}}}}\) and high Pi OPO, Fig. 3(b, c) plots these metrics as a function of resonator-waveguide gap, illustrating a strong increase in both as the resonator-waveguide gap decreases (and therefore as the Kp,i increase; see Fig. 2(c)). \({\eta }_{i}^{{{{{{\mathrm{max}}}}}}}\) based on Eq. (1) and the Kp,i values from Fig. 2(c) are plotted as a dashed line in Fig. 3(b). In general, the measured \({\eta }_{i}^{{{{{{\mathrm{max}}}}}}}\) values we report are still below the theoretical curve, likely due to imperfect frequency matching, where the pump detuning, Kerr, and thermal shifts do not perfectly compensate for Δν. In Fig. 3(c) we note that at smallest gap, we can generate isolated OPO with nearly 21 mW in the idler field (see Fig. 4(a)) despite some reduction in efficiency ( ≈ 190 mW pump), likely due to the aforementioned imperfect frequency matching. Finally, Fig. 4(b) displays a spectrum with ηi = 0.29 ± 0.04 and Pi ≈ 18.3 mW, recorded in Fig. 3(b, c) as a green dot at a gap of 300 nm, which is one of the highest conversion efficiencies achievable in our devices. At these levels of ηi and Pi, parasitic sidebands resurface, although the sidebands around the idler are still suppressed by more than 40 dB. Further improvements may be possible with continued device engineering to account for Kerr and thermal-shift contributions to the frequency mismatch.
We further consider the evolution of our OPO output as a function of pump power and pump laser tuning within the pump mode. In Fig. 3(a, inset) we plot a series of traces for waveguide-coupled pump powers between 70 mW and 165 mW, and for each trace we vary the pump laser frequency while recording Pi. The x-axis is referenced to the frequency at which the OPO threshold power (≈30 mW) is dropped into the cavity. That is, for each waveguide-coupled pump power, we adjust the pump laser frequency until the dropped power in the cavity is high enough to reach threshold, and that value is taken as zero detuning. Beyond threshold, each trace displays a steady increase in Pi (and hence ηi) until a maximum value for each is reached, after which the values decrease and eventually go to zero once frequency matching is completely lost. The detuning value at which this occurs depends on pump power, which is likely due to the differing thermal shifts of the cavity resonances and its impact on frequency mismatch. Once again, the strong normal dispersion for the pump mode family is successful in suppressing close-band parametric process, and pure OPO spectra with isolated pump/signal/idler tones like that in Fig. 3(a) are observed for much of the tuning range, though in some cases, the regions of highest conversion efficiency show additional parametric sidebands, as noted above and shown in Fig. 4(b). The additional sidebands remain strongly suppressed around the idler (40 dB to 50 dB below the idler), while in the signal band, they are only suppressed by ≈15 dB to 20 dB.
The absence of sidebands in Fig. 4(a) and their presence in Fig. 4(b) can be motivated from the understanding presented in the Suppressing Parasitic Processes section above. Namely, at 200 nm gap, the circulating power of each of the pump, signal, and idler fields is lower than that at 300 nm gap since the 300 nm gap is closer to critical coupling. Since the geometry of the rings (and hence their dispersion) is nominally the same, the greater circulating power within the 300 nm gap ring supports sideband formation more strongly than the power within the 200 nm gap ring. Furthermore, the large spectral separation ( >150 THz) between the signal and the idler allows the two tones to experience vastly different levels of cavity enhancement. Thus, considering the 300 nm gap device alone, one may expect the greater cavity enhancement near the signal (see Fig. 2) to support sideband formation more strongly than that near the idler. Nevertheless, some ambiguity persists because of the possibility that mode couplings result in local regions of near-zero dispersion (e.g., seen in the spread in the dispersion data) that might promote parasitic processes once the signal and/or idler power become sufficiently strong, and these mode couplings may differ for devices with different waveguide coupling parameters.
Finally, Fig. 3(d) shows \({\eta }_{{{\mbox{i}}}}^{{{\mbox{max}}}}\) and \({P}_{i}^{{{\mbox{max}}}}\) for this OPO device as a function of waveguide-coupled pump power. We observe a saturation of Pi and a monotonic reduction in ηi as the pump power increases, likely due to the aforementioned combination of pump-power-dependent frequency mismatch (due to thermal shifts) and competing parasitic processes near the signal and idler bands as explained above. Further mitigation of these effects is needed to continue to improve the power performance and conversion efficiency of these devices.
Discussion
In considering the potential applications and future development of the OPO devices we describe in this work, it is useful to place their performance in context with other demonstrated OPO systems9,12,14,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33. Figure 5 illustrates the output power for various OPO demonstrations, ranging from chip-integrated technologies to mm-scale resonators to larger table-top technologies, as a function of their input power. While OPO has seen tremendous progress at all scales, it stands to reason that a widely deployable on-chip device should have access to an on-chip pump source and produce output power suitable for downstream applications, which in some cases may require more than one milliwatt output on chip. As highlighted by the red gradients in Fig. 5, power considerations alone greatly reduce the number of OPO demonstrations amenable to deployable systems. The additional requirements of small-size and compatibility with silicon photonics leaves our microresonator device as a strong contender for the rapid and scalable deployment of a wide-wavelength-access laser system that simultaneously achieves high output power and conversion efficiency. In particular, we note the distinct application space for our chip-integrated system, where pump, signal, and idler waves are all widely separated in frequency, e.g., in comparison to nearly degenerate systems in either χ(2) or χ(3) platforms.
Furthermore, while Fig. 5 contextualizes the output power and conversion efficiency of our passively cooled device, other investigations12,14 have noted that supplementing similar χ(3) OPO systems with active thermal tuning can aid in aligning the OPO output wavelengths to an externally defined target wavelength. Given recent advancements18 in high-efficiency thermal tuning solutions for on-chip nonlinear nanophotonics devices, we expect thermal control of the refractive index to further strengthen the suite of features afforded by high performance OPO.
We emphasize that while integrated microresonator OPOs have realized high efficiency previously, it has largely been in a regime of low output powers (≈100 μW), with the exceptions of refs. 14,19, where a few mW of signal and idler power were generated from a 780 nm band pump, but the signal-idler separation was limited to a few tens of THz. Our work realizes output powers exceeding 20 mW at a signal-idler separation greater than 150 THz, while operating with pump powers that are still accessible from compact laser sources. This performance has been made possible through a combination of coupling engineering to efficiently inject the pump and extract the OPO output, and dispersion engineering to promote the nonlinear process of interest while suppressing competing parasitic processes. The former involves overcoupling of both the pump mode and targeted output mode (idler in our case) while maintaining high loaded Q, while the latter involves the use of a hybrid mode matching scheme in which all modes of interest are situated in regions of normal dispersion, but are nevertheless still able to realize phase- and frequency-matching. We note that table-top OPOs routinely produce significantly more than 100 mW of output power at high efficiency, though they require pump powers that are typically not easily available from compact laser sources. On the other end of the spectrum, breakthrough devices20,34 continue to usher in ultra-low threshold powers, but thus far with limited output powers. We note that in general, ultra-low threshold and high output power are not achieved simultaneously in χ(3) microresonator OPO devices, due to power-dependent Kerr frequency shifts. These shifts prevent a system that is frequency-matched for low power operation from being frequency-matched for high power operation, and degrading the device Q, to reduce the Kerr shifts by reducing the intracavity intensity, itself increases the threshold power.
To summarize, we demonstrate high-performance on-chip microresonator optical parametric oscillation that produces > 15 mW of output power at conversion efficiencies > 25%, without compromising on the span of the output signal and idler frequencies ( > 150 THz signal-idler separation). Simultaneously realizing these three features in an on-chip OPO represents a significant advance in the realization of flexible wavelength access for lasers. Furthermore, its development on a platform compatible with silicon photonics makes it well suited for wide-scale deployment outside of laboratory settings. This was accomplished by suppressing competitive processes within the resonator through the use of an hOPO scheme and by engineering the coupling to an access waveguide. Going forward, we expect combined coupling engineering and flexible frequency matching techniques, such as the hybrid mode-matching scheme used in this work (or recently implemented photonic crystal microring approaches35,36), to enable high-performance OPO across different wavelength bands, including the visible37 and mid-infrared9,38. Such work would further establish microresonator OPO as a practical approach for realizing high-performance laser wavelength access across a broad spectral range.
Methods
Characterization of OPO devices
The OPO devices under study were characterized using the experimental setup shown in Supplementary Fig. S1. For linear characterization of the devices, continuously tunable lasers (CTL) in the 780, 980, and 1300 nm bands were used. Each laser has a piezo-controlled (PZ-controlled) fine-frequency sweep modulated by a signal generator whose voltage is recorded by a data acquisition device (Oscilloscope in drawing). At the output of each laser, cascaded 90/10 and 50/50 couplers (at the appropriate wavelengths) provide light for two frequency measurements. As the PZ control voltage is modulated and recorded, the absolute frequency of the light is measured at the peaks of the driving saw-tooth voltage using a wavemeter. In between the saw teeth, displacements from the wavemeter-referenced frequencies are continuously recorded by Mach-Zehnder interferometers (MZIs) that feed into wavelength-compatible photodiodes. The use of an MZI allows us to track nonlinear deviations in the frequency sweeps of the laser. The 90% tap of the lasers is then attenuated to low powers ( ≈ 10 μW) using fiber-coupled attenuators (atten.) and aligned to a polarization of interest using fiber-coupled polarization controllers (PCs). Next, 10% (nominal rating at 980 nm) of the light is tapped to a power meter (PMin) to measure and monitor the power during subsequent steps and measurements. Finally, light is injected into the on-chip waveguide with a 980 nm lensed fiber. At the output of the chip, a similar lensed fiber is used to collect emission from the on-chip waveguide. 10 % of the collected light is routed to an optical spectrum analyzer (OSA) for analysis. Of the remaining light, 10% is tapped to monitor the insertion loss between points (A) and (B) in the diagram. To ensure precision, each of the couplers in the set up were characterized in each of the three wavelength bands. For simplicity, the nominal (i.e., 90/10 or 50/50) ratios are reported in the figure. The final portion of the light reaches a 980/1300 wavelength division multiplexer (WDM). The 980 nm light is coupled to a visible-light photo detector (PDVIS). The 1300 nm path routes the light through an 1100 nm long pass filter before being coupled to an infrared photodiode. The voltage of either PDVIS or PDIR (depending on the laser utilized) is recorded simultaneously with the voltages from the frequency measurement (i.e., the signal generator, MZI, and wavemeter measurements). The recorded voltages are then processed to provide transmission scans, like those shown in Fig. 2(d), which are then fit to Lorentzian lineshapes to determine the Qs of various devices. The dispersion measurements of our devices use the same setup and are acquired by manually tuning the laser frequency to the bottom of a resonance and measuring its frequency using a wavemeter.
For OPO characterization, the same set up was employed without the green dashed-line bypass. In this scheme, only the 980 CTL is used as a pump laser, with its output amplified by a tapered amplifier. In this configuration, the output photodiode (PDIR) measures voltage VIR = γiPi. The value of γi is determined by measuring the losses between (b) and (d) in the schematic, after which the measurements shown in Fig. 3 can be recorded.
Geometric characterization of OPO devices
The geometry of the OPO devices was explicitly checked through the use of focused ion beam (FIB) milling, which allows one to image a cross section of the ring resonator. A representative cross section is shown in Supplementary Fig. S2, which resembles an upside-down trapezoid with sidewall angles of approximately 16 degrees, as indicated in the image. The notch at the top of the trapezoid is unintended and likely due to the reflow and chemical mechanical polishing processes used in fabrication. However, the notch has a limited impact on the device dispersion since the optical fields circulate near the edge of the device, away from the notch (see Fig. 2(a) insets).
Data availability
The data that supports the plots within this paper and other findings of this study are available from the corresponding authors upon reasonable request.
References
Malik, A. et al. Low noise, tunable silicon photonic lasers. Appl. Phys. Rev. 8, 031306 (2021).
Park, H., Zhang, C., Tran, M. A. & Komljenovic, T. Heterogeneous silicon nitride photonics. Optica 7, 336 (2020).
Tran, M. et al. Extending the spectrum of fully integrated photonics to sub-micrometer wavelengths. Nature 610, 54–60 (2022).
Spott, A. et al. Heterogeneous integration for mid-infrared silicon photonics. IEEE J Sel. Top. Quantum Electron. 23, 1–10 (2017).
Boyd, R. W. Nonlinear Optics (Academic Press:Elsevier, 2010).
Agrawal, G. P. Nonlinear Fiber Optics (Elsevier/Academic Press, 2013).
Moss, D. J., Morandotti, R., Gaeta, A. L. & Lipson, M. New CMOS-compatible platforms based on silicon nitride and Hydex for nonlinear optics. Nat. Photon. 7, 597–607 (2013).
Xiang, C. et al. Laser soliton microcombs heterogeneously integrated on silicon. Science 373, 99–103 (2021).
Sayson, N. L. B. et al. Octave-spanning tunable parametric oscillation in crystalline Kerr microresonators. Nat. Photon. 13, 701–706 (2019).
Stone, J. R., Moille, G., Lu, X. & Srinivasan, K. Conversion efficiency in Kerr-microresonator optical parametric oscillators. Phys. Rev. Appl. 17, 024038 (2022).
Liu, J. et al. High-yield, wafer-scale fabrication of ultralow-loss, dispersion-engineered silicon nitride photonic circuits. Nat. Commun. 12, 2236 (2021).
Lu, X. et al. Milliwatt-threshold visible-telecom optical parametric oscillation using silicon nanophotonics. Optica 6, 1535 (2019).
Lin, Q., Johnson, T. J., Perahia, R., Michael, C. P. & Painter, O. J. A proposal for highly tunable optical parametric oscillation in silicon micro-resonators. Opt. Express 16, 10596 (2008).
Zhou, F. et al. Hybrid-mode-family Kerr optical parametric oscillation for robust coherent light generation on chip. Laser Photon. Rev. 16, 2100582 (2022).
Moille, G. et al. Broadband resonator-waveguide coupling for efficient extraction of octave-spanning microcombs. Opt. Lett. 44, 4737–4740 (2019).
Ji, X., Roberts, S., Corato-Zanarella, M. & Lipson, M. Methods to achieve ultra-high quality factor silicon nitride resonators. APL Photon. 6, 071101 (2021).
Kippenberg, T. J., Spillane, S. M. & Vahala, K. J. Kerr-nonlinearity optical parametric oscillation in an ultrahigh- Q toroid microcavity. Phys. Rev. Lett. 93, 083904 (2004).
Moille, G. et al. Integrated buried heaters for efficient spectral control of air-clad microresonator frequency combs. APL Photon. 7, 126104 (2022).
Bruch, A. W., Liu, X., Surya, J. B., Zou, C.-L. & Tang, H. X. On-chip χ(2) microring optical parametric oscillator. Optica 6, 1361 (2019).
Marty, G., Combrié, S., Raineri, F. & De Rossi, A. Photonic crystal optical parametric oscillator. Nat. Photon. 15, 53–58 (2021).
Lu, J. et al. Ultralow-threshold thin-film lithium niobate optical parametric oscillator. Optica 8, 539 (2021).
Ledezma, L. et al. Widely-tunable optical parametric oscillator in lithium niobate nanophotonics https://arxiv.org/abs/2203.11482 (2022).
Beckmann, T., Buse, K. & Breunig, I. Optimizing pump threshold and conversion efficiency of whispering gallery optical parametric oscillators by controlled coupling. Optics Lett. 37, 5250–5252 (2012).
Werner, C. S., Buse, K. & Breunig, I. Continuous-wave whispering-gallery optical parametric oscillator for high-resolution spectroscopy. Optics Lett. 40, 772 (2015).
Jia, Y. et al. Continuous-wave whispering-gallery optical parametric oscillator based on CdSiP 2. Opt. Express 26, 10833 (2018).
Ghotbi, M., Esteban-Martin, A. & Ebrahim-Zadeh, M. BiB3O6 femtosecond optical parametric oscillator. Opt. Lett. 31, 3128–3130 (2006).
Chaitanya Kumar, S., Das, R., Samanta, G. K. & Ebrahim-Zadeh, M. Optimally-output-coupled, 17.5 W, fiber-laser-pumped continuous-wave optical parametric oscillator. Appl. Phys. B 102, 31–35 (2011).
Kumar, S. C. & Ebrahim-Zadeh, M. High-power, fiber-laser-pumped, picosecond optical parametric oscillator based on MgO. Opt. Express 19, 26660 (2011).
Zhu, H. et al. High-efficiency intracavity Nd:YVO4/KTA optical parametric oscillator with 3.6 w output power at 1.53 μm. Opt. Express 17, 20669 (2009).
Haakestad, M. W., Fonnum, H., Arisholm, G., Lippert, E. & Stenersen, K. Mid-infrared optical parametric oscillator synchronously pumped by an erbium-doped fiber laser. Opt. Express 18, 25379 (2010).
Wei, K. et al. Fiber laser pumped high power mid-infrared laser with picosecond pulse bunch output. Opt. Express 21, 25364 (2013).
Liu, J. et al. Highly efficient tunable mid-infrared optical parametric oscillator pumped by a wavelength locked, Q-switched Er:YAG laser. Opt. Express 23, 20812 (2015).
Qijin Mo, Q. M. et al. Widely tunable optical parametric oscillator in periodically poled congruently grown lithium tantalite whispering gallery mode resonators. Chin. Opt. Lett. 14, 091902–91905 (2016).
McKenna, T. P. et al. Ultra-low-power second-order nonlinear optics on a chip. Nat. Commun. 13, 4532 (2022).
Black, J. A. et al. Optical-parametric oscillation in photonic-crystal ring resonators. Optica, 9, 1183–1189 (2022).
Lu, X., Chanana, A., Zhou, F. & Davanco, M. Kerr optical parametric oscillation in a photonic crystal microring for accessing the infrared. Opt. Lett. 47, 3331–3334 (2022).
Lu, X., Moille, G., Rao, A., Westly, D. A. & Srinivasan, K. On-chip optical parametric oscillation into the visible. Optica 7, 1417 (2020).
Tang, Y., Gong, Z., Liu, X. & Tang, H. X. Widely separated optical Kerr parametric oscillation in AlN microrings. Opt. Lett. 45, 1124 (2020).
Acknowledgements
This work is supported by the DARPA LUMOS and NIST-on-a-chip programs. The authors thank Dr. Junyeob Song from NIST for assistance with focused ion beam characterization of the microring resonator cross-section.
Author information
Authors and Affiliations
Contributions
E.P. led the project, conducted the experiments, data analysis, and paper writing. G.M. contributed to theoretical understanding, experimental design, data collection, and microresonator design. F.Z., X.L., and K.S. contributed to the understanding and characterization of the hOPO scheme employed. J.S. and K.S. contributed to the understanding and execution of parasitic process suppression. E.P., G.M., and K.S. prepared the manuscript. All the authors contributed to and discussed the content of this manuscript.
Corresponding author
Ethics declarations
Competing interests
NIST/UMD have filed patent applications, with X.L. and K.S. listed as inventors, related to the work presented in this article. E.F.P., G.M., J.S., and F.Z. declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Amir Safavi-Naeini, Chang-Ling Zou, and the other anonymous reviewer(s) for their contribution to the peer review of this work.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Perez, E.F., Moille, G., Lu, X. et al. High-performance Kerr microresonator optical parametric oscillator on a silicon chip. Nat Commun 14, 242 (2023). https://doi.org/10.1038/s41467-022-35746-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-022-35746-9
- Springer Nature Limited
This article is cited by
-
A wideband, high-resolution vector spectrum analyzer for integrated photonics
Light: Science & Applications (2024)
-
Ultra-efficient generation of time-energy entangled photon pairs in an InGaP photonic crystal cavity
Communications Physics (2023)