Abstract
Photonic integrated circuits (PICs) are revolutionizing nanotechnology, with far-reaching applications in telecommunications, molecular sensing, and quantum information. PIC designs rely on mature nanofabrication processes and readily available and optimised photonic components (gratings, splitters, couplers). Hybrid plasmonic elements can enhance PIC functionality (e.g., wavelength-scale polarization rotation, nanoscale optical volumes, and enhanced nonlinearities), but most PIC-compatible designs use single plasmonic elements, with more complex circuits typically requiring ab initio designs. Here we demonstrate a modular approach to post-processes off-the-shelf silicon-on-insulator (SOI) waveguides into hybrid plasmonic integrated circuits. These consist of a plasmonic rotator and a nanofocusser, which generate the second harmonic frequency of the incoming light. We characterize each component’s performance on the SOI waveguide, experimentally demonstrating intensity enhancements of more than 200 in an inferred mode area of 100 nm2, at a pump wavelength of 1320 nm. This modular approach to plasmonic circuitry makes the applications of this technology more practical.
Similar content being viewed by others
Introduction
Chip-based nanophotonic waveguides that incorporate photonic and electronic functionality on a compact, monolithic platform1 promise to revolutionize communications, sensing, and metrology2,3,4. The most promising approach being pursued relies on expanding existing silicon-on-insulator (SOI) technologies from the electronic to the optical domain, to produce photonic integrated circuits (PICs) exhibiting superior performance in terms of bandwidth and speed5,6. The quest for optical miniaturization is ultimately limited by diffraction—which in silicon corresponds to a maximum achievable spatial confinement of approximately 200 nm at telecommunication wavelengths. One of the most promising approaches for overcoming the diffraction limit by several orders of magnitude relies on nano-plasmonic structures7, which harness metals to compress light down to the molecular, and even atomic scale8,9. Moreover, the giant intensity enhancement provided by plasmonic nanofocusing—typically ~100–2000 times10—has attracted interest for ultrafast, high-bandwidth, low-power nonlinear optics applications11,12, e.g., for nano-scale sensing13 and all-optical wavelength conversion14. Plasmonics can be harnessed for nanoscale second- and third-harmonic generation, which respectively relied on either the large surface χ(2) or bulk χ(3) of the metal itself15,16,17, or on the large intensity enhancement within a dielectric at a plasmonic nanofocus14. This has mainly been demonstrated in planar structures that cannot be efficiently interfaced to PICs18.
Interfacing waveguide-based PICs with plasmonic nanostructures is challenging: typically, the latter is hindered by large losses (due to metallic absorption) and low coupling efficiency (due to extreme differences in the participating mode profiles). PICs and plasmonics can be married using hybrid plasmonic waveguides (HPWGs) containing a low-index buffer layer between the metal and the high-index waveguide, enabling relatively low propagation loss without sacrificing plasmonic confinement, and providing a convenient intermediate interface for coupling between photonic and plasmonic waveguides19,20. Whereas the efficient energy transfer between PIC-compatbile photonic and plasmonic structures has been under intense experimental investigation with a diverse range of functionalities21,22,23,24,25,26,27, including HPWG experiments demonstrating tight confinement and low propagation losses28,29,30, nonlinear experiments using this platform have been limited31.
While a number of simple HPWGs have been reported, the next challenge is to incorporate them into a more complex circuit with multiple modular, functional elements32—analogously to conventional PICs1. Ideally, such structures would be entirely chip-based, and be accessible using standard, industry-norm photonic components, thus simplifying the integration with more conventional technologies. Here we present the design, fabrication, and characterization of such a circuit, operating at λ = 1.32 μm. It consists of two modules: a mode converter that efficiently transforms an incoming photonic transverse electric (TE) mode into a hybrid-plasmonic transverse magnetic (TM) mode, followed by a plasmonic nanofocuser that functions as a nonlinear wavelength converter. We note that standard solutions exist for the coupling of light into the TE photonic waveguide, which here is achieved by using a grating with an incident free-space Gaussian beam. In this way, our device thus represents a fully integrated chip by which a free-space Gaussian beam is focused to a cross-section that is almost two orders of magnitude below the diffraction limit in silicon, with a concomitant increase in intensity. To demonstrate that this increased intensity is due to the focuser, we fabricate and characterize two similar devices: one with a partial focuser and one with no focusing element at all. Note that while preliminary reports of both a TE-to-TM rotator33 and directional-coupling-based TM-nano-focuser30 have been reported separately, this is a proposal and demonstration of combining these two modular elements into a monolithic PIC-compatible plasmonic integrated circuit. This approach has clear advantages in terms of both design flexibility (enabling an industry-standard TE-waveguide input to achieve plasmonic nano-focusing), and wider bandwidth (enabled by the quasi-adiabatic modal evolution).
Results
Circuit design
Our on-chip hybrid plasmonic integrated circuit (HPIC) is formed by two in-series plasmonic elements on a SOI waveguide (WG): a mode converter and a focuser. The latter combines a taper and a sharp tip, which functions as a nonlinear nanoscale light source. In our particular demonstration, we probe second harmonic generation (SHG) in the visible from a near-infrared pump. Figure 1a shows a schematic of the HPIC. The first component (i) is formed by a polarization rotator33 (also operating as a TE-photonic to TM-plasmonic mode converter34); the second (ii) is a nanofocusing gold tip10 resulting in SHG due to the intense nanoscale localization of the optical field, combined with the large surface χ(2) of gold18. Figure 1c shows an electron micrograph of a fabricated HPIC on a SOI waveguide, highlighting the ~10 nm tip sharpness, which is limited only by the gold grains generated during the evaporation process35.
To analyze our circuit we first consider the relevant HPIC modes during propagation. Figure 2a shows the result of 2D finite element (FE) simulations (COMSOL) of the modal evolution along the HPIC. Figure 2a also shows a top-view schematic of Fig. 1 for clarity. In the first instance, a gold film36 (tAu = 50 nm) with a SiO2 spacer underneath37 (tspacer = 20 nm) gradually extends on a silicon waveguide (350 nm × 220 nm, nSi = 3.5) until complete coverage (here, ℓstrip = 30–300 nm, as defined in Fig. 2). The red line in Figure 2a shows how the hybrid-TE (HTE) mode evolves within the waveguide, in terms of the real effective index and loss. The input is the fundamental TE-SOI mode of the bare waveguide, which excites the HTE mode (i) that rotates into a hybrid-TM mode (HTM) (ii). The HTM mode is then converted to a deep-subwavelength HTM plasmonic mode (iii)38 by reducing the gold strip width (wstrip = 300–10 nm, as defined in Fig. 2). The z-component of the time-averaged Poynting vector Sz associated with each participating mode is shown in Fig. 2b, and presents the salient features of the evolution of TE-SOI mode after it couples to the HTE mode. The modal evolution of the equivalent HTM mode is shown as the blue curve in Fig. 2a for completeness. The TE-SOI waveguide mode excites both the HTE and HTM hybrid plasmonic eigenmodes in location (i), each evolving in a non-trivial way along the device.
a An industry-standard TE ridge waveguide is followed by two in-series plasmonic circuit modules: (i) efficient TE-photonic to TM-plasmonic rotator and (ii) nano-focusing tip. b Geometric parameters at the rotator-focuser boundary. c Scanning electron micrograph (SEM) of a fabricated device. Scale bar: 400 nm. Here, wSi = 350 nm; hSi = 220 nm; g = 25 nm; tspacer = 20 nm; tAu = 50 nm Inset: high-resolution nanotip detail, revealing 10 nm apex sharpness.
a Calculated effective index \({\mathbb{R}}e({n}_{{\rm{eff}}})\) and loss for relevant modes (λ = 1.32 μm). Red line: a TE mode at input (TE SOI) (i) couples to a hybrid TE (HTE) mode, (ii) evolving to a rotated hybrid TM (HTM) mode, and (iii) transitions to a nano-focused HTM plasmonic mode. The dashed blue line shows the HTM-to-HTE evolution. b Corresponding mode profiles as labeled. White arrows represent the dominant electric field direction. The color represents the z-component of the time-averaged Poynting vector Sz. Window size: 0.8 × 0.8 μm2. See Fig. 1 caption for relevant parameters.
We next calculate the performance of the full device using full 3D FE simulations. Due to the many parameters, materials, and functionalities involved, the optimization of the complete device is challenging: first, a suitable compromise between adiabaticity (requiring a slow modal transition, i.e., a long device length) and loss (requiring short device lengths) is required; secondly, small changes in geometric parameters, alignment, and surface roughness can have a significant impact on the conversion efficiency. However, this process can be significantly simplified by using the modularity, which enables us to consider each element separately.
We model the fabricated structure shown in Fig. 1c. The cross-section of the Ex and Ey field components in the middle of the Si-WG are shown in Fig. 3a. Note in particular the polarization rotation in the spacer, manifesting as a vanishing Ex component and an emerging Ey component. A detailed plot of the electric field intensity ∣E∣2 within the spacer near the tip is shown in Fig. 3b, showing a strong local enhancement at the tip apex. We calculate a ~1200× intensity enhancement at the gold surface with respect to the peak intensity in the silicon for the TE-SOI input. Figure 3c shows Sz in each xy cross-section as indicated by the dashed lines in Fig. 3a(i)–(iv). We calculate the conversion efficiency between the incoming TE-SOI mode and each of the participating modes in the full device by performing overlap integrals between the calculated 3D fields of Fig. 3c and the 2D modes of Fig. 2, as outlined in ref. 34.
a Electric field components in the xy plane (a) in the middle of the silicon waveguide, showing polarization rotation (vanishing Ex and emerging Ey). Window size: 7 × 1 μm2. b Field intensity ∣E∣2 in the middle of the spacer, showing nano-concentration of energy. Window size: 1.5 × 0.2 μm2. c Time-averaged Poynting vector Sz at each of the locations (i)–(iv) and input as labeled in (a). Inset: relative contribution (in %) for each mode shown in Fig. 234.
The mechanism that converts the TE mode at input (Fig. 3a (input)) to the TM mode at the end of the rotator (Fig. 3a(ii)) is complicated by the fact that the waveguide evolves continuously over wavelength-scale propagation lengths, and that this is a lossy structure. In the rotator section, the gold-nanofilm overlayer tapers sideways relative to the underlying silicon waveguide, beginning on one corner on top of the silicon waveguide. Since the beginning of the rotator is formed by a sharp gold nanotip off-axis (Fig. 3a(i)), energy is distributed between the HTE and HTM mode, with most of the energy being coupled into the HTE mode for the TE SOI WG input considered. Our calculations using the method presented in ref. 34 indicate that the HTE and HTM modes at the start of the rotator are excited with a coupling efficiency of 70% and 30%, respectively (Fig. 3c(i)). As the gold film gradually tapers sideways to cover the waveguide, these two orthogonal modes evolve by rotating their polarization. In a quasi-adiabatic treatment33, as the gold film gradually tapers sideways to cover the waveguide, the rotation mechanism can be interpreted to originate from the dominant electric field remaining orthogonal to the metal surface. Due to the asymmetry at input, the input HTE mode of the waveguide rotates into the HTM mode. A pioneering experimental study identified three possible regimes, depending on the rotator length chosen33: a non-adiabatic regime (short coupler, low power transfer); an adiabatic regime (long coupler, strong absorption); and a quasi-adiabatic regime with good power transfer to the desired mode at an intermediate length, which is the region where we operate. We obtain a TE-to-HTM (rotator) conversion efficiency of 41%, comparable to previous reports33, and a TE-to-HTM (nanofocus) conversion efficiency of 12%, also comparable to the state of the art for plasmonic nanofocusing14. Note that 9% of the TE mode remains in the WG at output, which can be improved, for example, by more sophisticated multi-section rotator designs39.
Fabrication and linear experiments
With an eye on the potential for modular approach to enhance off-the-shelf photonic waveguides with tailored plasmonic functionality, we purposefully choose to integrate our HPICs on previously fabricated SOI-WGs with standard electron-beam lithography and evaporation techniques. Figure 4 shows an optical microscope image of an example bare SOI-WG with length L = 20 μm: light is coupled in and out of the waveguide with shallow gratings optimized for TE polarization. For further details of the bare SOI-WG design and characterization, see “Methods” and Supplementary Fig. 1. The HPIC nanostructures, shown in Fig. 1c, were deposited on the WG in a subsequent step via combination of electron-beam lithography, SiO2/gold evaporation, and lift-off—note in particular the excellent quality of the gold film, the sharp tip obtained, and the high alignment precision (<10 nm resolution). The details of the HPIC fabrication procedure are presented in the “Methods” and in Supplementary Fig. 2. Preliminary experimental waveguide characterization in the near-infrared (NIR) was performed by coupling light from free space (λ = 1320 μm) onto the waveguide input grating coupler using a 100× near-infrared microscope objective (NA = 0.85—Olympus) and observing the light scattered by the device using a InGaAs camera (NIRvana, Princeton Instruments) (see “Methods” and Supplementary Fig. 3). The resulting measurement is shown in Fig. 4b. The field emerging from each nanoscale tip appears as a diffraction-limited spot, since all tips have physical dimensions well below the diffraction limit. We observe a diffraction-limited spot at the expected location of the gold nanotip, as well as residual TE light contained within the waveguide (in agreement with the simulations, see Fig. 3a(iv)), originating from the output grating. Figure 4c shows the same measurement when inserting a polarizer between the sample and camera with different orientations: we measure that the diffraction-limited spot is longitudinally (TM) polarized40, confirming polarization rotation and that light exiting the grating is TE polarized. As further confirmation, Fig. 4d shows a direct comparison of the amount of light exiting the grating in the presence of the HPIC, with respect to an adjacent control sample without the HPIC. From the ratio of the total power scattered by each TE grating under comparable input conditions (see Supplementary Fig. 4), we conclude that the residual light in the TE waveguide in the presence of the HPIC, relative to the bare SOI waveguide, is (13 ± 1)%, in agreement with 3D simulations (see Fig. 3c(iv)).
a Microscope image of a 20 μm WG with an HPIC (SEM inset). Light is coupled to the waveguide using a TE grating at input. b Measured light from the output TE grating and the tip (dashed line in (a)). c Placing a polarizer between scattered light and camera confirms that light from the tip is TM polarized, while light from the grating is TE polarized. White arrows in (c) show polarizer orientation. d Measured light scattered by the output grating with and without the HPIC, resulting in 13% relative transmittance. Colorscale in (b), (c), and (d) represents the number of photon counts measured by the InGaAs camera, divided by the maximum number of counts measured in (b) and (d), respectively.
Nanofocusing and nonlinear enhancement
Plasmonic nanofocusing leads to spot sizes that are well below the diffraction limit, so that far-field linear optical experiments are inherently incapable of characterizing the focusing performance of our HPIC. Here we harness the high field intensities at the apex of the gold tip to estimate the field enhancement via nonlinear SHG experiments. Here, the surface nonlinear susceptibility χ(2) of gold dominates over that of all surface and bulk sources of all constituent materials41. Ultrashort pump pulses (λp = 1320 nm, 200 fs, 80 MHz31) are coupled into the TE mode of the photonic waveguide via a grating coupler. They then enter one of three HPIC-enhanced WGs, each possessing incrementally sharper tips: the three HPIC considered here are shown in Fig. 5a. Scattered light images by each HPIC captured using near-infrared (NIR) and visible (VIS) cameras (PIXIS—Princeton Instruments) are shown in Fig. 5b, c, respectively. While nonlinear generation/scattering occurs during propagation across the entire HPIC15, due to the large absorption of silicon (approximately 12 dB over 10 μm at 660 nm42), the absence of phase matching, and the wavelength-scale propagation lengths considered, we can attribute the measured nonlinear signal only to the localized intensity at the edge of the gold tip from which the NIR light emerges. The spectra of the NIR pump and the visible radiation are shown in the inset of Fig. 6a. The figure confirms that the visible radiation indeed is the second harmonic of the pump since λSHG = λp/2 = 660 nm. We observe that the sharpest tip causes the least amount of NIR scattering, consistent with 3D simulations (see Supplementary Fig. 5). In contrast, this tip also causes the strongest visible light emission (see Fig. 5b, c, magenta), even though the incident power is an order of magnitude smaller than in the other two cases—a preliminary indicator of nonlinear enhancement. In this case, the input power is reduced by 10 times in order to avoid damaging the sharp due to the high field strength.
a SOI-HPIC scanning electron micrographs, with tip width of 300 nm (blue), 138 nm (red), and 10 nm (magenta). Measured scattering from the SOI-HPIC b in the NIR c and visible. Images in (b) and (c) are respectively captured under the same conditions, unless otherwise indicated. Pin is the average power incident onto the input grating for the three captured images in (c). The color bar represents the number of counts measured in (b) and (c), divided by the maximum number of counts in (b) and (c), respectively.
a Circles: square root of the measured yield for each sample (color coding as in Fig. 5). Dashed lines: linear fits confirming quadratic dependence on incident power (\({I}_{{\rm{SHG}}}^{1/2}\propto {P}_{{\rm{in}}}\)). Inset: spectra of the pump (blue), and of the SHG from the tip (orange). b Calculated enhancement (left axis, solid line) and effective area (right axis, dashed line) as a function of strip width for a focuser length of 3 μm, relative to the largest wstrip = 300 nm, following38. Light- and dark-blue shadow encompass the enhancement values predicted by full 3D simulations and the Eikonal model respectively, see Supplementary Fig. 5b. Black crosses show the experimentally measured relative increase in intensity, obtained from the square of the slopes in (a)—error bars from confidence intervals of the straight line fits in (a) are smaller than symbol size. Black circles: calculated effective area range of 50– 200 nm2 for wstrip = 10 nm.
To quantify the nonlinear response of each tip, we measure the raw spectral yield versus incident power at the SHG wavelength, as shown in Fig. 6a (circles). The linear relationship between the square root of the yield and the average power incident on the sample Pin (corresponding to a quadratic input power dependence, \({I}_{{\rm{SHG}}}^{1/2}\propto {P}_{{\rm{in}}}\)), further confirms the mechanism of SHG. As a first conclusion, we note the dramatic increase in SHG intensity for the sharpest tip, which indicates that nano-focusing was achieved. We compare the slopes of the three curves quantitatively via a linear fit to the experiment, as shown in the dashed lines of Fig. 6a, and infer the relative intensity enhancement with respect to the strip. The results are summarized in Fig. 6b, which shows the intensity enhancement as a function of the tip width obtained using different approaches. Black crosses show the measured enhancement, obtained by taking the square of the slopes in Fig. 6a, normalized to wstrip = 300 nm. We experimentally observe a maximum intensity enhancement of a factor ~216 ± 16 for the sharpest gold tip relative to the gold strip (uncertainties are obtained from the confidence intervals of the straight line slopes in Fig. 6a). The predicted range of theoretical enhancement at the tip is shown in the dark blue shaded region of Fig. 6b (left axis), and was calculated using an Eikonal approach38, in excellent agreement with both the experiment and the range of intensity enhancements at the tip predicted by full 3D simulations (light blue region—see Supplementary Fig. 5 for further details). Note that the enhancement predicted by the Eikonal approach is inversely proportional to the effective mode area Aeff, the definition of which can vary12,38,43. For completeness, Fig. 6b shows the range of inferred effective mode area for wstrip = 10 nm, i.e., Aeff ~ 50–200 nm[2 42 (black circles, in agreement with published calculations38).
Finally, we estimate the SHG conversion efficiency. After taking into account the effect of all optical elements, we conclude that the maximum SHG power is emitted by the sample for the sharpest nanotip (Fig. 6a, magenta) is 2.3 fW for an incident power of 0.22 mW, corresponding to a net conversion efficiency of 10−11. Taking into account the coupling efficiency into the waveguide (14%, see Supplementary Fig. 1d), this corresponds to ~0.7 × 10−10 of the power in the waveguide before the plasmonic rotator, and ~0.6 × 10−9 of the inferred power in the TM mode at the tip (cfr. Fig. 2d(ii)). Though these values are comparable to optimized nonlinear plasmonic SHG geometries44,18, our geometry has the significant advantage of being on a PIC-compatible platform. It is worth noting that only ~0.06% of the power generated by a TM point source on the surface of a silicon waveguide radiates upwards, whereas the great majority of the SHG light is scattered into (and absorbed by) the silicon waveguide (see Supplementary Fig. 6). Future work will focus on new strategies to make use of the generated SHG, e.g., using hydrogenated amorphous silicon with low absorption at visible wavelengths, which will enable measurements of the SHG signal captured by the photonic waveguide45.
Discussion
The conversion efficiency could be further improved by optimizing the individual modular elements. Separate calculations for each module predict a peak rotator conversion efficiency of 58% for a rotator length of 4 μm, and of 34% for a focuser length of 1 μm (keeping all other parameters constant), resulting in a compound conversion efficiency of 20%. This is in good agreement with equivalent calculations for the full device, predicting a maximum conversion efficiency of 24% for the same rotator and focuser lengths of 4 and 1 μm, respectively. Thus, we estimate that through modest changes of the device parameters (e.g., increasing the gold thickness or with multi-section tapers39 with up to 95% conversion efficiency), the pump TE-to-TM efficiency could be improved by approximately 9×, which would lead to a ~80-fold increase in nonlinear conversion efficiency. Further improvements may be achieved either by incorporating 2D materials on the waveguide surface, which possess a χ(2) that is at least 1 order of magnitude greater than gold surfaces45. Additionally, χ(3) nonlinear effects such as third-harmonic generation and four-wave-mixing may be accessed by placing highly nonlinear materials at the nanofocus14. Further enhancement may be achieved with additional plasmonic modules, such as a bowtie nanoantenna46 adjacent to the tip, or additional focuser and rotator modules which couple light back into the photonic waveguide.
This experiment represents a PIC-compatible, integrated nonlinear-plasmonic-SHG nanoscale light source, that makes use of two, in-series hybrid-plasmonic circuit elements. This design, fabrication, and characterization represent a TM plasmonic nano-focuser that is monolithically interfaced with an industry-standard TE-input SOI waveguide, and which can be coupled into by a conventional grating coupler. This work opens the door to the development of modular plasmonic circuit elements that can be seamlessly integrated on off-the-shelf photonic waveguides. Note that there has been a recent discussion of CMOS-compatible hybrid plasmonic waveguides47,48, which requires using aluminum or copper as metals. We believe that this PIC can be easily fabricated using CMOS-compatible metals such as Cu and Al, which would result in rotator modules with comparable TE-to-TM conversion efficiencies34, as well as focuser modules with similar enhancement38 (see Supplementary Fig. 7). Our approach unifies the emerging modular nanophotonic-circuit paradigm32 with hybrid-integration of plasmonic nano-elements on industry-standard waveguides27,26, extending the range of accessible structures to efficient hybrid plasmonic waveguides culminating in deep-subwavelength mode volumes, by performing three difficult-to-access optical functions (namely rotation, nano-focusing, and nonlinear conversion) back-to-back and on an integrated platform. This approach will facilitate access to efficient PIC-compatible deep-subwavelength field enhancements for on-chip quantum photonics and spectroscopy49, nonlinear13 and atomic-scale9 sensing, and nanoscale terahertz sources and detectors50.
Methods
Photonic waveguide grating design and characterization
The waveguide gratings were designed in-house using a 2D solver CAMFR51, with infinite air cladding and silicon substrate layer, a box layer of 2 μm thick, and a silicon waveguide layer of 220 nm, presenting grooves with an etching depth of he and a period of Λ. Here, he = 80 nm and period Λ = 440 nm, resulting in a high coupling efficiency (Tup = 51%), and wide bandwidth centered in λ = 1320 nm, low reflection (R = 3.5%), and a selective in-coupling angle (−11°). From images of the optimized coupling to the waveguide, referenced to a mirror, we obtain a grating coupling efficiency of 14%, assuming that the loss due to each grating is equal. Waveguide losses without the HPIC are measured to be 0.12 dB μm−1 using waveguides of different lengths. See Supplementary Fig. 1 for further details of the calculations, the calculated bandwidth, and experimental measurements of coupling- and propagation-losses.
Hybrid plasmonic integrated circuit fabrication
The plasmonic HPICs are integrated on the SOI waveguides as follows. First, the silicon waveguides are spin-coated with polymethyl methacrylate resist, and the HPIC structures are written with standard electron-beam lithography and developed with methyl isobutyl ketone. 20 nm silica and 50 nm gold are subsequently coated with electron-beam evaporation. Finally, a lift-off step (methyl-isobutyl-ketone) removes the resist. The alignment precision (~10 nm) is obtained using local gold markers, placed in the immediate vicinity of our off-the-shelf waveguides. See Supplementary Fig. 2 for a schematic of the fabrication procedure and alignment markers used.
Experimental setup
A detailed schematic of the experimental setup is shown in Supplementary Fig. 3. The source is an optical parametric oscillator (λp = 1320 nm, FWHM: 200 fs; repetition rate: 80 MHz). The power incident on the sample is controlled via a motorized half-waveplate placed before a polarizer. The beam is spatially shaped using a beam expander, telescope, and elliptical lens, so that its profile matches that of the input waveguide grating. A beamsplitter (BSPM) and powermeter (PM) monitor the input power. A microscope holds the WGs and HPICs. Light is delivered and collected to the sample via a 100× NIR microscope objective (Olympus, NA = 0.85) and BS. A short-pass filter (850 nm) is included in SHG experiments to filter out the NIR light. The scattered light is measured with an imaging spectrometer, using NIR (NIRvana) and VIS (PIXIS) cameras. An additional NIR camera at a second output monitors alignment. The laser power drift is <±0.5%. Sample-to-sample waveguide coupling conditions fluctuate by ±4%, as obtained from the standard deviation of the total power emitted by the output grating of 10 nominally identical bare waveguide samples for optimized coupling conditions.
Data availability
The data that support the findings of this study are available from the corresponding author upon reasonable request.
References
Chrostowski, L. & Hochberg, M. Silicon Photonics Design: From Devices to Systems (Cambridge University Press, 2015).
Dong, P. et al. Monolithic silicon photonic integrated circuits for compact 100+ Gb/s coherent optical receivers and transmitters. IEEE J. Sel. Top. Quantum Electron. 20, 150–157 (2014).
Estevez, M. C., Alvarez, M. & Lechuga, L. M. Integrated optical devices for lab-on-a-chip biosensing applications. Laser Photonics Rev. 6, 463–487 (2012).
Marpaung, D., Yao, J. & Capmany, J. Integrated microwave photonics. Nat. Photonics 13, 80–90 (2019).
Lipson, M Guiding, modulating, and emitting light on silicon-challenges and opportunities. J. Lightwave Technol. 23, 4222–4238 (2005).
Chen, L., Preston, K., Manipatruni, S. & Lipson, M. Integrated GHz silicon photonic interconnect with micrometer-scale modulators and detectors. Opt. Express 17, 15248–15256 (2009).
Zia, R., Schuller, J. A., Chandran, A. & Brongersma, M. L. Plasmonics: the next chip-scale technology. Mater. Today 9, 20–27 (2006).
Taylor, A. B. & Zijlstra, P. Single-molecule plasmon sensing: current status and future prospects. ACS Sens. 2, 1103–1122 (2017).
Lee, J., Crampton, K. T., Tallarida, N. & Apkarian, V. A. Visualizing vibrational normal modes of a single molecule with atomically confined light. Nature 568, 78–82 (2019).
Gramotnev, D. K. & Bozhevolnyi, S. I. Plasmonics beyond the diffraction limit. Nat. Photonics 4, 83–91 (2010).
Kauranen, M. & Zayats, A. V. Nonlinear plasmonics. Nat. Photonics 6, 737–748 (2012).
Li, G., de Sterke, C. M. & Palomba, S. Fundamental limitations to the ultimate Kerr nonlinear performance of plasmonic waveguides. ACS Photonics 5, 1034–1040 (2018).
Kravtsov, V., Ulbricht, R., Atkin, J. M. & Raschke, M. B. Plasmonic nanofocused four-wave mixing for femtosecond near-field imaging. Nat. Nanotechnol. 11, 459–464 (2016).
Nielsen, M. P., Shi, X., Dichtl, P., Maier, S. A. & Oulton, R. F. Giant nonlinear response at a plasmonic nanofocus drives efficient four-wave mixing. Science 358, 1179–1181 (2017).
de Hoogh, A., Opheij, A., Wulf, M., Rotenberg, N. & Kuipers, L. Harmonics generation by surface plasmon polaritons on single nanowires. ACS Photonics 3, 1446–1452 (2016).
Celebrano, M. et al. Mode matching in multiresonant plasmonic nanoantennas for enhanced second harmonic generation. Nat. Nanotechnol. 10, 412 (2015).
Lassiter, J. B. et al. Third-harmonic generation enhancement by film-coupled plasmonic stripe resonators. ACS Photonics 1, 1212–1217 (2014).
Butet, J., Brevet, P.-F. & Martin, O. J. F. Optical second harmonic generation in plasmonic nanostructures: from fundamental principles to advanced applications. ACS Nano 9, 10545–10562 (2015).
Oulton, R. F., Sorger, V. J., Genov, D. A., Pile, D. F. P. & Zhang, X. A hybrid plasmonic waveguide for subwavelength confinement and long-range propagation. Nat. Photonics 2, 496 (2008).
Alam, M. Z., Aitchison, J. S. & Mojahedi, M. A marriage of convenience: hybridization of surface plasmon and dielectric waveguide modes. Laser Photonics Rev. 8, 394–408 (2014).
Briggs, R. M., Grandidier, J., Burgos, S. P., Feigenbaum, E. & Atwater, H. A. Efficient coupling between dielectric-loaded plasmonic and silicon photonic waveguides. Nano Lett. 10, 4851–4857 (2010).
Delacour, C. et al. Efficient directional coupling between silicon and copper plasmonic nanoslot waveguides: toward metal-oxide-silicon nanophotonics. Nano Lett. 10, 2922–2926 (2010).
Lin, C., Wong, H. M. K., Lau, B., Swilam, M. A. & Helmy, A. S. Efficient broadband energy transfer via momentum matching at hybrid junctions of guided-waves. Appl. Phys. Lett. 101, 123115 (2012).
Melikyan, A. et al. High-speed plasmonic phase modulators. Nat. Photonics 8, 229–233 (2014).
Haffner, C. et al. Low-loss plasmon-assisted electro-optic modulator. Nature 556, 483–486 (2018).
Li, Z. et al. Controlling propagation and coupling of waveguide modes using phase-gradient metasurfaces. Nat. Nanotechnol. 12, 675–683 (2017).
Guo, R. et al. High-bit rate ultra-compact light routing with mode-selective on-chip nanoantennas. Sci. Adv. 3, e1700007 (2017).
Kim, J. T. et al. Hybrid plasmonic waveguide for low-loss lightwave guiding. Opt. Express 18, 2808–2813 (2010).
Sorger, V. J. et al. Experimental demonstration of low-loss optical waveguiding at deep sub-wavelength scales. Nat. Commun. 2, 331 (2011).
Luo, Y. et al. On-chip hybrid photonic-plasmonic light concentrator for nanofocusing in an integrated silicon photonics platform. Nano Lett. 15, 849–856 (2015).
Diaz, F. J. et al. Sensitive method for measuring third order nonlinearities in compact dielectric and hybrid plasmonic waveguides. Opt. Express 24, 545–554 (2016).
Shi, J. et al. Modular assembly of optical nanocircuits. Nat. Commun. 5, 3896 (2014).
Caspers, J. N., Aitchison, J. S. & Mojahedi, M. Experimental demonstration of an integrated hybrid plasmonic polarization rotator. Opt. Lett. 38, 4054–4057 (2013).
Kim, S. & Qi, M. Polarization rotation and coupling between silicon waveguide and hybrid plasmonic waveguide. Opt. Express 23, 9968–9978 (2015).
Doron-Mor, I., Barkay, Z., Filip-Granit, N., Vaskevich, A. & Rubinstein, I. Ultrathin gold island films on silanized glass. morphology and optical properties. Chem. Mater. 16, 3476–3483 (2004).
Johnson, P. D. & Christy, R. W. Optical constants of the noble metals. Phys. Rev. B 6, 4370–4379 (1972).
Malitson, I. H. Interspecimen comparison of the refractive index of fused silica. J. Opt. Soc. Am. 55, 1205–1209 (1965).
Lafone, L., Sidiropoulos, T. P. H. & Oulton, R. F. Silicon-based metal-loaded plasmonic waveguides for low-loss nanofocusing. Opt. Lett. 39, 4356–4359 (2014).
Chang, Y.-J. & Feng, R.-W. Hybrid plasmonic mode converter: theoretical formulation and design with a graphical approach. Appl. Opt. 56, 5501–5510 (2017).
Tuniz, A., Chemnitz, M., Dellith, J., Weidlich, S. & Schmidt, M. A. Hybrid-mode-assisted long-distance excitation of short-range surface plasmons in a nanotip-enhanced step-index fiber. Nano Lett. 17, 631–637 (2017).
Che, F., Grabtchak, S., Whelan, W. M., Ponomarenko, S. A. & Cada, M. Relative SHG measurements of metal thin films: gold, silver, aluminum, cobalt, chromium, germanium, nickel, antimony, titanium, titanium nitride, tungsten, zinc, silicon and indium tin oxide. Results Phys. 7, 593–595 (2017).
Aspnes, D. E. & Studna, A. A. Dielectric functions and optical parameters of Si, Ge, GaP, GaAs, GaSb, InP, InAs, and InSb from 1.5 to 6.0 eV. Phys. Rev. B 27, 985–1009 (1983).
Gao, L. et al. Active metal strip hybrid plasmonic waveguide with low critical material gain. Opt. Express 20, 11487–11495 (2012).
Zhang, Y., Grady, N. K., Ayala-Orozco, C. & Halas, N. J. Three-dimensional nanostructures as highly efficient generators of second harmonic light. Nano Lett. 11, 5519–5523 (2011).
Chen, H. et al. Enhanced second-harmonic generation from two-dimensional MoSe2 on a silicon waveguide. Light: Sci. Appl. 6, e17060 (2017).
Peyskens, F., Dhakal, A., Van Dorpe, P., LeThomas, N. & Baets, R. Surface enhanced raman spectroscopy using a single mode nanophotonic-plasmonic platform. ACS Photonics 3, 102–108 (2015).
Fedyanin, D. Y., Yakubovsky, D. I., Kirtaev, R. V. & Volkov, V. S. Ultralow-loss CMOS copper plasmonic waveguides. Nano Lett. 16, 362–366 (2015).
Dabos, G. et al. Aluminum plasmonic waveguides co-integrated with Si3N4 photonics using CMOS processes. Sci. Rep. 8, 13380 (2018).
Tame, M. S., McEnery, K. R., Özdemir, Ş. K., Lee, J. & Maier, S. A. Quantum plasmonics. Nat. Phys. 9, 329–340 (2013).
Salamin, Y. et al. Direct conversion of free space millimeter waves to optical domain by plasmonic modulator antenna. Nano Lett. 15, 8342–8346 (2015).
Taillaert, D. et al. Grating couplers for coupling between optical fibers and nanophotonic waveguides. Jpn. J. Appl. Phys. 45, 6071–6077 (2006).
Acknowledgements
A.T. acknowledges support from the University of Sydney Fellowship Scheme. S.K. acknowledges the support by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) under Germany’s Excellence Strategy—EXC-2123 QuantumFrontiers—390837967. This work was performed in part at the NSW node of the Australian National Fabrication Facility (ANFF).
Author information
Authors and Affiliations
Contributions
A.T. conceived the idea and designed the experiment with input from S.P. and C.M.d.S. A.T. performed the simulations, experiments, and fabrication of the hybrid plasmonic circuit. O.B. designed the plasmonic device and fabricated the alignment markers. F.J.D. designed the bare silicon waveguides and the experimental setup. T.K., S.K., and E.-B.K. fabricated the bare waveguides. A.T. and C.M.d.S. wrote the manuscript with input from S.P. A.T., C.M.d.S., and S.P. directed the project.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Peer review information Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Tuniz, A., Bickerton, O., Diaz, F.J. et al. Modular nonlinear hybrid plasmonic circuit. Nat Commun 11, 2413 (2020). https://doi.org/10.1038/s41467-020-16190-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-020-16190-z
- Springer Nature Limited
This article is cited by
-
An Investigation of Low-Loss Sodium Plasmon Waveguides Based on FEM
Plasmonics (2024)
-
Polarization-insensitive plasmon nanofocusing with broadband interference modulation for optical nanoimaging
Nano Research (2023)
-
Experimental confirmation of self-imaging effect between guided light and surface plasmon polaritons in hybrid plasmonic waveguides
Scientific Reports (2022)
-
Characteristics of a Symmetric Mid-infrared Graphene Dielectric Hybrid Plasmonic Waveguide with Ultra-deep Subwavelength Confinement
Plasmonics (2022)
-
Ultra-compact and -broadband integrated plasmonic waveplates with high efficiency
Applied Physics B (2022)