Abstract
Cell-free systems designed to perform complex chemical conversions of biomass to biofuels or commodity chemicals are emerging as promising alternatives to the metabolic engineering of living cells. Here we design a system comprises 27 enzymes for the conversion of glucose into monoterpenes that generates both NAD(P)H and ATP in a modified glucose breakdown module and utilizes both cofactors for building terpenes. Different monoterpenes are produced in our system by changing the terpene synthase enzyme. The system is stable for the production of limonene, pinene and sabinene, and can operate continuously for at least 5 days from a single addition of glucose. We obtain conversion yields >95% and titres >15 g l−1. The titres are an order of magnitude over cellular toxicity limits and thus difficult to achieve using cell-based systems. Overall, these results highlight the potential of synthetic biochemistry approaches for producing bio-based chemicals.
Similar content being viewed by others
Introduction
Terpenes comprise one of the largest classes of industrially relevant bioactive natural products and have found wide use as flavours, fragrances, biofuels, commodity chemicals, vitamins and pharmaceuticals1,2,3,4,5. While many of the industrial and pharmaceutically relevant terpenes in use are plant-derived6, low yields from natural sources limit their use and makes production subject to the unpredictability of agricultural boom and bust cycles7,8. Production in metabolically engineered microbes could therefore provide an attractive alternative for increased terpenoid production9,10,11,12. Escherichia coli and Saccharomyces cerevisiae have both been successfully engineered to produce monoterpenes such as limonene13, pinene14 and sabinene15; sesquiterpenes such as santalene16,17, bisabolene18 and amorphadiene19; and diterpenes such as sclareol20, taxadiene21 and carotinoids22. Nevertheless, the high titres and yields needed for economic viability of high-volume chemical uses have generally not been realized. Even in the case of monoterpenes limonene and pinene where established supply streams exist, their wider adoption as bio-safe solvents and biofuels is limited by amounts produced in nature23. Titres of terpenes are typically very low (<0.5 g l−1), and in even the best reported cases are only around ≤1.5 g l−1 (refs 24, 25). The notable exception is amorphadiene, which can be produced at 40 g l−1 in S. cerevisiae, but the yields are too low (17% carbon yield) to be useful for low-cost chemicals such as biofuels19.
Multiple factors limit the success of engineered microbes for terpene production (and biochemical production in general), including toxicity of products or intermediates, competing endogenous pathways, difficult pathway optimization (at both the transcriptional and translational level) and expensive product isolation from complex growth media26. In the case of monoterpenes limonene and pinene, a cellular toxicity limit of ≤0.5% (5 g l−1) is a major contributor to low titres and presents a key barrier for production in a microbial host27,28.
Cell-free production provides an alternative approach to chemical transformations that can ease the technical challenges of engineering microorganisms and the limitations imposed by requiring cell viability26. Rather than engineer cells to produce and house the desired biochemical pathway, the cell-free approach simply mixes enzymes together in a reaction vessel (either from crude preparations or purified)29,30,31,32. While freedom from the constraints of the cell has many advantages, it also poses challenges because the complex regulatory systems and biochemical replenishing systems that exist in cells are eliminated. The design of enzyme systems that can be self-sustaining for long periods of time requires special considerations—a process we call synthetic biochemistry32.
Here we use synthetic biochemistry to build a system for the production of monoterpenes from glucose. The system is stable and functions continuously for at least 5 days without any further additions of cofactors or enzymes. The high yields and titres for limonene (12.5±0.3 g l−1) and pinene (14.9±0.6 g l−1) are nearly an order of magnitude higher than that has been demonstrated in living systems. Our results suggest that commodity chemicals and pharmaceutical intermediates derived from acetyl-CoA and ATP are accessible through synthetic biochemistry systems.
Results
Overview of in vitro monoterpene biosynthesis from glucose
The challenges facing synthetic biochemistry can be seen in the conversion of glucose to monoterpenes by a combination of the Embden–Meyerhof–Parnas (EMP) glycolytic and the mevalonate pathways. The mevalonate pathway requires 3 acetyl-CoA, 2 NADPH and 3 ATP to yield the terpene-building blocks isopentenyl pyrophosphate or dimethylallyl pyrophosphate. From 1.5 glucose, standard EMP glycolysis (hereafter referred to as ‘glycolysis’) will yield the 3 acetyl-CoA and the net 3 ATP needed, but will also produce 6 NADH, creating two problems: (1) an excess of reducing equivalents is produced; and (2) they are of the wrong type (NADH rather than NADPH) so that NAD+ would not be recycled. We have previously developed a method to handle NAD(P)H/NAD(P)+ balancing by creating enzymatic purge valve nodes32,33 that use a combination of NAD+- and NADP+-utilizing dehydrogenases and NADH oxidase (NoxE) so that NADPH can be generated via the NADP+-utilizing dehydrogenase, but excess reducing equivalents can be purged via NoxE to maintain carbon flux (see ref. 31 for description). The ATP pay-in phase of glycolysis presents an additional complication because if ATP is used too rapidly in the first hexokinase (Hex) step, there will be no ATP left to allow flux through the phosphofructokinase step34. Finally, high-energy phosphate for all metabolites (for example, the γ-phosphate of ATP) is ultimately (re)generated from inorganic phosphate (Pi), so that Pi concentrations can affect flux through the system.
The goal of this study was to show that glucose breakdown through glycolysis can produce enough carbon building blocks and ATP to drive an important anabolic process (for example, the mevalonate pathway). So far, complex cell-free systems for building chemicals have either avoided the use of ATP completely30 or stoichiometrically balance ATP use and consumption during catabolic reactions only35. While ATP-specific regeneration systems have been developed, these are generally simple systems consisting of only a few enzymes that utilize sacrificial substrates (for example, polyphosphate or acetyl-phosphate)36,37. It remains unclear whether excess ATP (for example, the net 2 ATP produced from glycolysis) can be effectively used outside the cell to drive anabolic pathways in a fully recyclable manner30,31. In the synthetic biochemistry system we designed (Fig. 1 and Supplementary Fig. 1), ATP, NADPH and acetyl-CoA are generated using glycolysis reconstituted from purified components (Supplementary Table 1). NADPH production is regulated with a new molecular purge valve at the glyceraldehyde-3-phosphate dehydrogenase (Gap) step (rather than the pyruvate dehydrogenase (Pdh) step described previously32) by including a mutant Gap (mGap) that is specific for NADP+ along with NoxE. Geranyl-pyrophosphate is ultimately produced through the canonical mevalonate pathway using the acetyl-CoA, ATP and NADPH output from the engineered EMP pathway. Various monoterpenes can then be made simply by adding different monoterpene synthases in the final step following geranyl-pyrophosphate production. Importantly, pyrophosphate released by the prenyltransferase and terpene synthase steps is then converted back to Pi by the action of a pyrophosphatase, ensuring that all cofactors (ATP/ADP/NAD/NADP/CoA/Pi) are recycled continuously in situ and there is no build-up of any metabolite besides the intended product. We also added catalase, glutathione and glutathione reductase to ensure the system maintains a reduced environment (Supplementary Table 1).
Enzymes in each submodule (coloured boxes) are labelled as described in the text and Supplementary Table 1. ATP-consuming and -generating steps are shown in purple and blue, respectively. The NADPH-generating purge valve is shown in red while the NADPH-consuming top of the mevalonate pathway is shown in orange. Solid arrows show the flow of cofactors and dotted arrows highlight their recycle through respective steps in the pathway.
Modelling with CoPASI to identify potential bottlenecks
To ensure that our designed system could run effectively in theory, and to determine factors that may contribute to maximizing overall titres of limonene from glucose, we developed a computer model using CoPASI38. Although we have not measured kinetic parameters for the enzymes used experimentally, our goal was to explore fundamental features of the overall system design. We therefore used kinetic parameters defined for homologous enzymes where needed to obtain a reasonable model. Equations describing enzyme kinetics for glycolysis and the mevalonate pathway were taken from established models describing yeast metabolism39 (Supplementary Note) with values for Km, Vmax and Keq based on published values in the BRENDA database40 and previous modelling experiments39. The Gap purge valve (including EcGap, mGap and NoxE) and pyrophosphatase were also included in the model. The final parameters and equations are provided in the Supplementary Note.
A virtual time course was performed starting with 500 mM glucose and system parameters (for example, Vmax or starting cofactor concentration) were adjusted to identify features important for the reaction to go to completion (final values shown in Supplementary Table 2). We focused on parameters that would allow the reaction to go to completion rather than improve reaction rate because we wanted to develop a system that was robust and sustainable, that is, could run for long periods of time without intervention (Fig. 2a). Modelling with CoPASI suggests that system sustainability is particularly sensitive to Hex (Fig. 2b) and Pdh enzyme activity (Fig. 2c), and also to initial Pi concentration (Fig. 2d).
(a) Levels for glucose (black line), limonene (blue line) and cofactors (ATP, ADP, G6P, F16BP, Pi and PPi) in an optimized CoPASI model starting at 500 mM glucose and a time of 20,000 s (5.6 h). Glucose and limonene levels are plotted on the left axis and cofactor levels are plotted on the right axis. (b) Parameter scan in CoPASI showing the dependence of limonene production on units of Hex varied between 0.05 and 0.15 units. (c) Parameter scan in CoPASI showing the dependence of limonene production on units of Pdh varied between 1 and 50 units. (d) Parameter scan in CoPASI showing the dependence of limonene production on starting Pi varied between 1 and 50 mM. (e) Experimental data showing the dependence of limonene production on units of Hex, Pdh and Pi. (f) Experimental data showing the dependence of limonene production on the ratio of Hex and Pfk units to the kinases in the mevalonate pathway: Mvk; Pmvk; and Mdc (MevKs). The reactions in c and d were started with the addition of 250 mM glucose and analysed after 16 h.
The importance of Hex and Pi is perhaps unsurprising as Hex and Pi are instrumental in ATP usage and recycling. It has been noted previously that too much Hex activity leads to a build-up of glucose-6-phosphate (G6P) and depletion of ATP, which is needed for the phosphofructokinase reaction34. ATP depletion can thereby block passage through the ATP pay in phase of glycolysis. Similarly, sequestration of Pi in hexose phosphates (for example, G6P and fructose-1,6-bisphosphate) can block the Gap step, shutting down glycolysis (Supplementary Fig. 2a). The strong dependence of the reaction sustainability on Pdh activity is less clear. Since Pdh is followed by the first three ATP-independent steps of the mevalonate pathway (Fig. 1 and Supplementary Fig. 1), it is possible that too little Pdh causes a lag before ATP usage via Mvk, Pmvk and Mdc. As a result of this lag, Hex and Pfk might out-compete the kinases in the mevalonate pathway and again phosphate would become sequestered in hexose phosphates at the top of glycolysis. Overall, CoPASI modelling suggests that initial levels of Hex, Pi and Pdh are the most critical contributors to successful conversion of glucose to limonene (Supplementary Fig. 2b).
Implementation of in vitro monoterpene production system
Since the modelling results suggest that the system design could function in a sustainable fashion, we set out to implement the pathway. We set initial cofactor concentrations and the relative glycolysis enzyme levels as described in a prior work41. The rest of the enzymes levels were set so they would not be rate-limiting. We then varied Hex, Pdh or Pi concentrations over a 10-fold range, keeping the rest of the system concentrations constant. Figure 2e shows the dependence of limonene titres on the amount of Hex, Pi or Pdh input during a 16 h reaction. For Pi or Pdh, the extent of reaction increases with increasing loading until a threshold is met, consistent with the COPASI modelling results. The limonene titre increased with increasing units of Hex activity to a certain point after which the limonene titre began to decline. If too much Hex was added, the rate of glucose phosphorylation outpaced Pfk and Mvk, Pmvk and Mdc activity. As shown in Fig. 2f, adding additional units of Pfk, Mvk, Pmvk and Mdc recovers limonene titre to starting conditions. The results suggest that if the kinase steps are not balanced, Pi becomes sequestered in G6P, fructose-6-phosphate and fructose-1,6-bisphosphate (FBP; hexose phosphates), and Gap activity ceases. Clearly, care must be taken to balance Hex activity with all other kinases.
Purge valve requirement for sustainable limonene production
To test whether a molecular purge valve is necessary to drive the mevalonate pathway using glycolysis, we developed a new molecular purge valve at the Gap step (composed of an NAD+-dependent Gap from E. coli, an NADP+-dependent mGap from Geobacillus stearothermophilus and NoxE) and evaluated the consequences of eliminating purge valve components. As shown in Fig. 3, leaving out any part of the new molecular purge valve significantly compromises the ability of the system to convert glucose into limonene. In fact, leaving out NoxE completely abolished limonene production from glucose as seen in prior characterization of other purge valves32,33. The dependence on NoxE is not surprising since both the molecular purge valve and Pdh rely on NoxE activity for unimpeded flux. With the full system, 2.57±0.15 g l−1 (average of three independent measurements; n=3) limonene could be produced in 24 h. Therefore, the new molecular purge valve at Gap can produce NADPH and maintain enough flux to provide ATP and acetyl-CoA for limonene production.
The graph shows the dependence of limonene production from glucose on the purge valve implemented at the Gap step. Various components were left out of each reaction (Gap, wild-type Gap from E. coli; mGap, NADP+-specific mutant Gap from G. stearothermphilus; NoxE, NADH oxidase from Lactococcus lactis). The last experiment (+Gap, +mGap and +NoxE) contains all components. Leaving out any component leads to reduced limonene production from glucose. All reactions were started with the addition of 250 mM glucose and analysed after 16 h. Reactions were performed in triplicate (n=3) and analysed as described in the Methods. Error bars represent s.d. ND, not determined.
Continuous production of limonene from glucose
To test efficient and sustainable in vitro production of limonene from glucose, we set up a semi-optimized system (Supplementary Table 3) and allowed the reaction to proceed for multiple days from a single addition of glucose. To monitor function and longevity, a single addition of 100 mM (Fig. 4a), or 200 mM glucose (Fig. 4b) was added at the start and the reaction was evaluated at various time-points for limonene production, remaining glucose and levels of ATP and Pi (Fig. 4). Within 2 days, 4.94±0.18 g l−1 (n=3) limonene was produced from 100 mM glucose (Fig. 4a), which corresponds to a 100% theoretical yield at a maximum productivity of ∼0.1 g l−1 h−1. Monitoring glucose (total hexose and hexose phosphates), ATP and Pi show that all glucose input is consumed and ATP and Pi cycle accordingly (Fig. 4c). When twice as much glucose was input (200 mM), glucose consumption and limonene production rates were nearly constant over 5 days reaching 8.87±0.59 g l−1 (n=3) limonene and correspond to a theoretical yield of 97.6% (Fig. 4b). When ATP and Pi were monitored concurrently (Fig. 4d), both ATP and Pi levels decrease to a low basal level (∼200 μM and 2 mM for ATP and Pi, respectively) and then fluctuate over the course of 4 days as would be expected (that is, when ATP is higher, Pi is lower and vice versa). When 200 mM glucose was input, the limonene titre did not plateau until day 4 when all of the available glucose had been consumed, suggesting the system could progress further. Finally, to determine the full extent of biosynthetic capability for the in vitro system, 500 mM glucose was input and limonene production monitored over 7 days. At day 7, limonene reached a final titre of 12.5±0.3 g l−1 (n=3; Fig. 5) with a total yield of 88.3%±4.6% (n=3) of theoretical suggesting little or no loss of carbon due to side reactions. Our in vitro production of 12.5 g l−1 limonene directly from glucose is nearly an order of magnitude higher than has so far been demonstrated for limonene production in living systems42 and >2 times the toxicity limit of between 0.02 and 0.5% for E. coli or S. cerevisiae27,43.
Time course of limonene production, glucose consumption, and ATP and Pi levels starting from either 100 (a,c) or 200 mM (b,d) glucose over 5 days. The reaction starting from 200 mM glucose produces twice as much limonene over 5 days compared to starting with 100 mM glucose. Reactions were performed in triplicate (n=3) and analysed as described in the Methods. Error bars represent s.d.
The chart shows production of monoterpenes limonene, pinene and sabinine from 500 mM glucose over 7 days. The final titre of monoterpenes and glucose remaining were determined by GC and enzyme assay as described in the Methods. For the limonene synthase reaction (green bar), the product was 100% limonene. For the pinene synthase reaction (purple bar), the product distribution is 80.8±0.33% α-pinene and 19.2±0.33% β-pinene. For the sabinene synthase reaction catalysed by the N345A Limonene synthase mutant (orange bar), the product distribution is 11.5±0.03% α-pinene, 11.2±0.01% β-pinene, 37.9±0.02% (−)-sabinene, 3.5±0.01% (+)-sabinene, 27.1±0.04% limonene and 5.7±0.01% myrcene. Reactions were performed in triplicate (n=3) and analysed as described in the Methods. Error bars represent s.d.
Production of other monoterpenes from glucose
To test whether our synthetic biochemistry system could be used as a broad platform for the production of other monoterpenes, we attempted to produce pinene and sabinene from glucose. To make pinene or sabinene, the appropriate monoterpene synthase was simply swapped with the limonene synthase used above. For pinene synthesis, α-pinene synthase from Picea sitchensis was used, which has been shown to produce a mixture of 77% α-pinene and 22% β-pinene44. For sabinene production the limonene synthase mutant N345A was used, which produces sabinene as its major product along with smaller amounts of other monoterpenes45. Starting with 500 mM glucose, monoterpene production was allowed to proceed for 7 days and then quantified by GC (Supplementary Fig. 3). Pinene titre (sum of α-pinene and β-pinene nearly identical to distribution in ref. 44) reached 14.9±0.6 g l−1 (n=3) while sabinene titre (total monoterpenes, similar distribution to ref. 45) was 15.9±0.4 g l−1 (n=3) with yields of 103.9%±8.1% (n=3) and 94.5%±4.7% (n=3) of theoretical, respectively (Fig. 5). Like limonene production, these values are at least an order of magnitude higher than microbial production for pinene14 and sabinene15 and multiple times higher than the toxicity limit for these compounds15,43.
Discussion
Our results show that industrially relevant complex biomolecules such as monoterpenes can be produced in vitro directly from glucose using a synthetic biochemistry platform. Specifically, we find that the ATP and the carbon-building block acetyl-CoA generated by glycolysis can be used to drive the biosynthesis of complex compounds directly from glucose, a low-cost, renewable feedstock. This represents a significant expansion of synthetic biochemistry platform as both acetyl-CoA and ATP are needed for the biosynthesis of many desirable products besides terpenes. We were able to produce monoterpenes at high titres (12.5±0.3, 14.9±0.6 and 15.9±0.4 g l−1 for limonene, pinene and sabinene, respectively) and yields (88.3±4.6%, 103.9±8.1% and 94.5±4.7% of theoretical, respectively), and production was continuous over many days without any further additions of enzyme or cofactors. While the flux reported here is still about an order of magnitude below rates needed for industrial production (0.1 versus 1–2 g l−1 h−1), this work significantly improves on a previous, less-complicated system41 from phosphoenolpyruvate (PEP) to isoprene in both rate (0.014 g l−1 h−1) and overall extent of reaction (for example, titre and scale). Rates for in vitro production of less-complex molecules such as ethanol34,46, 2,3-butanediol47, mevalonate31 and polhydroxybutyrate33 from glucose in either a lysate or purified system range from 0.7 to as high as 47.9 g l−1 h−1, suggesting that the rate for in vitro terpene production could be raised if either more terpene synthase were used or the rate was significantly improved through engineering. Therefore, with further optimization of reaction conditions as well as in vitro evolution of enzyme stability and activity (for example, terpene synthase), it should be possible to develop a faster system that functions for much longer.
Without the limitations of toxicity and substrate competition, it should also be possible to expand the synthetic biochemistry platform to make sesquiterpenes and diterpenes simply by changing two proteins. Because the system works with an excess of NADPH, it is also possible to envision the incorporation of modifying enzymes such as cytochrome P450s to further expand the number and diversity of products generated.
Our results suggest that synthetic biochemistry has the potential to reach industrially relevant production parameters for a wide range of complex molecules that are difficult to produce in vivo. The key will be to keep enzyme costs low by finding stable enzymes so they can be used for long periods of time, methods for recycling the enzymes and inexpensive purification methods. Implementing a more stable system with engineered enzymes that last for weeks or months will significantly lower the cost of the enzymes not only in terms of dollars but also in initial input of glucose needed to produce enzymes (which was not taken into consideration for our yield calculations). The longer the proteins last (that is, higher total turnover number), the larger the reduction in up-front costs, including glucose. Our monoterpene platform demonstrates that in vitro systems can reach yields and titres required for industrial production of specialty bio-based chemicals but significant improvements are necessary in areas such as stability and total turnover number before synthetic biochemistry can begin to challenge synthetic biology for production of commodity chemicals from biomass.
Methods
Chemicals and reagents
All buffers, reagents and cofactors (for example, bis-tris propane, glucose, limonene, pinene, sabinene, FBP, ATP, NAD(P)+, coenzyme A and so on) were purchased from Sigma-Aldrich. Yeast Hex (H6380) was from Sigma. Hexanes, isopropyl myristate and nonane were from ARCOS and were the highest grade available. Liquid and solid media for growth of E. coli was from Fisher Scientific (BD Difco).
Cloning and purification of enzymes
All enzymes were cloned into pET28a(+) (Novagen) with an N-terminal 6xHis-tag unless otherwise noted (Supplementary Table 1). NCBI gene accession codes used in this work are listed in Supplementary Table 1. Primers used for cloning are listed in Supplementary Table 4. E. coli strain BL21Gold(DE3) (Agilent) was used for both cloning and overexpression of His-tagged proteins. Genes were amplified from plasmid or genomic DNA using HotStart Taq Mastermix (Denville) and then cloned into PCR-amplified vectors using a modified Gibson method as described previously41,48. Mutagenesis of limonene synthase to introduce the N345A mutation45 and GsGap to construct the D32A/L33R/T34K triple mutant was done using the Quickchange Site-Directed Mutagenesis Kit (Stratagene).
For overexpression and purification of all constructs (except Pdh, see below), 1 l of Luria broth (LB) media containing antibiotic was induced with 0.4 mM isopropyl-β-D-thiogalactoside once the optical density 600 nm reached 0.6. After 16 h incubation, soluble 6xHis-tagged proteins were purified from clarified cell lysates by Ni-NTA affinity chromatography, adjusted to 10% glycerol, flash-frozen with liquid N2 and stored at −80 °C until use. For terpene synthases, enzymes were concentrated to ∼20 mg ml−1 with a 30 kDa molecular weight cut-off concentrator (Amicon) before freezing.
Assembly and purification of Pdh complex
All three subunits of the Pdh complex (AceE, AceF and Lpd) were cloned as N-terminal 6xHis-tag constructs as above. The AceE and Lpd subunits of Pdh were expressed and purified individually by Ni-NTA. For AceF overexpression, the media was supplemented with 0.2 mM (±) lipoic acid before induction with isopropyl-β-D-thiogalactoside. Following lysis, AceF was precipitated by two additions of ammonium sulfate to 25 and 55%. The pellet from the 55% ammonium sulfate addition was dialysed into 25 mM Tris-Cl (pH 8.5), and purified by ion-exchange chromatography using a 25 ml HiTrap Q column. Fractions containing AceF were pooled, and AceF was isolated by ultracentrifugation (105,000 g for 3 h). The pellet containing AceF was resuspended in 25 mM Tris-Cl (pH 8) containing 10% glycerol and then mixed with Ni-NTA-purified AceE and Lpd. The mixture was allowed to incubate at 4 °C for 30 min to form the complex and then isolated by ultracentrifugation (105,000 g for 3 h). The resulting yellow pellet was resuspended in 7 ml 25 mM Tris-Cl (pH 8) and 0.1 M NaCl containing 50% glycerol, and stored at −20 °C.
CoPASI modelling
CoPASI v4.16 was downloaded from http://copasi.org/ (ref. 38). For simulation and analysis of the combined glycolytic and mevalonate pathways designed in this study, Km and kcat values were obtained from the BRENDA database40 (Supplementary Table 2) and rate equations (Supplementary Note and Supplementary equations (1)–(23)) were derived based on descriptions of yeast metabolism39. A time course task was run with a timescale of 20,000 s and parameters adjusted until a steady rate of conversion of glucose into limonene was obtained. Next, a parameter scan task was performed for the Vmax of various enzymes or starting concentration of various cofactors (for example, Pi or ATP) over either a 10- or 50-fold range in 20 steps to identify bottlenecks and optimum starting conditions. Bottleneck enzymes (for example, Pdh) were identified by starting with a 250- to 500-fold excess over Hex and systematically decreasing each enzyme to a 5- to 10-fold excess followed by monitoring limonene production over 20,000 s. Pdh was the only enzyme that failed to run to completion during the given time frame.
Enzyme assays
Enzymes used in this work were assayed as described previously32,33,41. In general, enzymes that produce or consume NAD(P)H were monitored at 340 nm. Enzymes that do not produce or consume NAD(P)H directly were coupled to an enzyme that does (for example, FBP aldolase coupled to glyceraldehyde-3-phosphate dehydrogenase). Enzymes that consume or produce ATP were monitored at 340 nm using a coupled assay to NADH consumption through the activity of pyruvate kinase and lactate dehydrogenase. All readings were performed in triplicate (n=3) using a SpectraMax M5 Plate Reader.
Initial limonene production from glucose
Initial reactions for the continuous in vitro bioconversion of glucose to limonene were composed of 100 mM Tris-Cl (pH 7.5), 6 mM MgCl, 10 mM KCl, 2 mM ADP, 2 mM ATP, 1 mM FBP, 1.5 mM CoA, 0.5 mM NAD+, 1.5 mM NADP+, 100 mM glucose, 0.5 mM thiamine pyrophosphate, 0.25 mM 2,3 bisphosphoglycerate, 5 mM reduced glutathione and 10 mM Pi in a final volume of 200 μl. Glutathione reductase and catalase were simply added as a precaution to prevent oxidation over the course of 7 days. We did not optimize or investigate the need for these components. As the overall system design with the purge valve produces an excess of NADPH, there is sufficient NADPH in the system to supply glutathione reductase. The enzyme concentrations are given in Supplementary Table 3. The reactions were initiated with the addition of glucose followed by carefully overlaying the reaction sample with 600 μl isopropyl myristate. The reactions were allowed to proceed for at least 24 h and gentle shaking with limonene production monitored by gas chromatography equipped with a flame ionization detector (GC-FID).
Initial levels of glycolysis enzyme loadings were set based on data from Scopes and Welch34 for in vitro ethanol production from glucose. Levels for Pdh and mevalonate pathway enzymes were set based on measured (PhaA, Hmgs, Hmgr, Mvk, Pmvk and Mdc) or reported (Idi and Fpps) units per milligram values such that none of the mevalonate pathway enzymes (with the exception of limonene synthase) were limiting. Minimal optimization was performed by varying key enzyme (Hex, Pdh, NoxE, Gap and mGap) and cofactor (NAD+, ATP and phosphate) levels until a maximum titre could be established in 24 h that was dependent on the terpene synthase activity. Final enzyme loadings are listed in Supplementary Table 3.
Continuous terpene production from glucose
Reactions were set up in triplicate at a volume of 200 μl in 2 ml glass vials and incubated uncapped with an organic overlay at 25 °C and gentle shaking. Each reaction contained 100 mM bis-tris propane (pH 7.5), 20 mM potassium phosphate (pH 7.5), 1 mM FBP, 4 mM ATP, 1.5 mM NADP+, 0.2 mM NAD+, 1.5 mM CoA, 6 mM MgCl2, 10 mM KCl, 0.5 mM thiamine pyrophosphate, 0.25 mM 2,3 bisphosphoglycerate and 5 mM glutathione. For limonene and pinene production, GsFpps mutant S82F was used in combination with Mentha spicata limonene synthase (produces 100% 4S-limonene) or P. sitchensis α-pinene synthase (produces 5:1 ratio of α and β pinene), respectively. For sabinene production, M. spicata limonene synthase mutant N345A was used (which produces sabinene as its major product along with smaller amounts of five other monoterpenes). The total catalyst load is detailed in Supplementary Table 3. Reactions were initiated with the addition of 125, 250 or 500 mM (final) glucose and then immediately overlaid with 600 μl isopropyl myristate. Reactions were allowed to proceed for the time indicated, vortexed for 5 s and centrifuged for 2 min at 16,060 × g to separate the aqueous and organic layers. For analysis and quantification of terpene production, 75 μl of the organic layer was mixed with 175 μl hexanes and analysed by GC-FID. For analysis of residual glucose, ATP and phosphate, the bottom aqueous layer was separated to a new tube, brought back to 200 μl with buffer and heat-treated for 2 min at 95 °C to denature proteins. Samples were then centrifuged (16,060 × g for 2 min) and stored at −20 °C until analysis.
The yield was calculated by dividing the moles of monoterpene produced by the theoretical moles of monoterpene that could be produced from the moles of glucose that entered the system (that is, glucose consumed, not total glucose input). The amount of glucose that entered the system was calculated by the amount of glucose measured at t=0 minus the amount of glucose remaining at t=7 days. All reactions were performed in triplicate (n=3).
Analytical methods
Terpenes isolated in the organic layer were analysed by GC-FID (HP5890II) equipped with a HP-INNoWax column (0.32 mm × 30 m, Agilent). A volume of 1 μl was injected and terpenes were identified and quantified by comparison to an authentic standard curve (limonene, α-pinene or sabinene). Representative traces are shown in Supplementary Fig. 3. The carrier gas was helium with a flow rate of 5 ml min−1. The oven temperature was kept at 70 °C for 3 min, raised to 260 at 5 °C min−1 and then held at 260 °C for 3 min. The inlet and detector temperatures were kept at 250 and 300 °C, respectively.
For analysis of glucose, a coupled enzymatic assay was performed based on reduction of NAD+ to NADH by Gap. Briefly, heat-treated samples were diluted and 2 μl was added to 200 μl assay mix containing 100 mM Tris-Cl (pH 7.5), 5 mM MgCl2, 10 mM KCl, 1 mM ATP, 2 mM NAD+, 7 mM Pi and fresh Hex, Pgi, Pfk, Ald, Tpi, Gap and Pgk. The change in absorbance was monitored for 10 min at 340 nm. The amount of glucose present was calculated based off a standard curve from known quantities of glucose.
For analysis of ATP, the ATP Bioluminescent Assay Kit (Sigma-Aldrich) was used. Before performing the quantification, the ATP Assay Mix was diluted 625-fold with ATP-Assay Mix Dilution buffer. To quantify ATP, 100 μl of a 1:100 diluted sample was added to 100 μl ATP Assay Mix and the luminescence was measured immediately. A standard curve for ATP was run concurrently and used to calculate the amount of ATP present.
For analysis of Pi, the Malachite Green Phosphate Detection Kit (R&D Systems) was used. A volume of 1 μl of a 1:100 dilution of sample was added to 49 μl H2O and then processed according to the manufacturer’s directions. Phosphate was calculated by comparison to a standard curve run concurrently with known amounts of Pi.
Data availability
NCBI gene accession codes used in this work are listed in Supplementary Table 1. All the other data supporting the findings of this study are available within the paper and its Supplementary Information files and from the corresponding author on reasonable request.
Author contibutions
All the authors contributed to the conception and planning of the project. T.P.K. and P.H.O. performed the experiments. All the authors analysed the results. T.P.K. and J.U.B. wrote the manuscript.
Additional information
How to cite this article: Korman, T. P. et al. A synthetic biochemistry platform for cell free production of monoterpenes from glucose. Nat. Commun. 8, 15526 doi: 10.1038/ncomms15526 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
Oldfield, E. & Lin, F.-Y. Terpene biosynthesis: modularity rules. Angew. Chem. Int. Ed. 51, 1124–1137 (2012).
Dixon, R. A. Plant natural products: the molecular genetic basis of biosynthetic diversity. Curr. Opin. Biotechnol. 10, 192–197 (1999).
Withers, S. T. & Keasling, J. D. Biosynthesis and engineering of isoprenoid small molecules. Appl. Microbiol. Biotechnol. 73, 980–990 (2006).
Krings, U. & Berger, R. G. Biotechnological production of flavours and fragrances. Appl. Microbiol. Biotechnol. 49, 1–8 (1998).
Ajikumar, P. K. et al. Terpenoids: opportunities for biosynthesis of natural product drugs using engineered microorganisms. Mol. Pharm. 5, 167–190 (2008).
Bohlmann, J., Meyer-Gauen, G. & Croteau, R. Plant terpenoid synthases: molecular biology and phylogenetic analysis. Proc. Natl. Acad. Sci. USA 95, 4126–4133 (1998).
Gershenzon, J. Metabolic costs of terpenoid accumulation in higher plants. J. Chem. Ecol. 20, 1281–1328 (1994).
Jongedijk, E. et al. Biotechnological production of limonene in microorganisms. Appl. Microbiol. Biotechnol. 100, 2927–2938 (2016).
Zhang, M. M., Wang, Y., Ang, E. L. & Zhao, H. Engineering microbial hosts for production of bacterial natural products. Nat. Prod. Rep. 33, 963–987 (2016).
Martin, V. J. J., Pitera, D. J., Withers, S. T., Newman, J. D. & Keasling, J. D. Engineering a mevalonate pathway in Escherichia coli for production of terpenoids. Nat. Biotechnol. 21, 796–802 (2003).
Kirby, J. & Keasling, J. D. Metabolic engineering of microorganisms for isoprenoid production. Nat. Prod. Rep. 25, 656–661 (2008).
Carroll, A. L., Desai, S. H. & Atsumi, S. Microbial production of scent and flavor compounds. Curr. Opin. Biotechnol. 37, 8–15 (2016).
Alonso-Gutierrez, J. et al. Metabolic engineering of Escherichia coli for limonene and perillyl alcohol production. Metab. Eng. 19, 33–41 (2013).
Yang, J. et al. Metabolic engineering of Escherichia coli for the biosynthesis of alpha-pinene. Biotechnol. Biofuels 6, 60 (2013).
Zhang, H. et al. Microbial production of sabinene—a new terpene-based precursor of advanced biofuel. Microb. Cell Factories 13, 20 (2014).
Jones, C. G. et al. Sandalwood fragrance biosynthesis involves sesquiterpene synthases of both the terpene synthase (TPS)-a and TPS-b subfamilies, including santalene synthases. J. Biol. Chem. 286, 17445–17454 (2011).
Tippmann, S., Scalcinati, G., Siewers, V. & Nielsen, J. Production of farnesene and santalene by Saccharomyces cerevisiae using fed-batch cultivations with RQ-controlled feed. Biotechnol. Bioeng. 113, 72–81 (2016).
Peralta-Yahya, P. P. et al. Identification and microbial production of a terpene-based advanced biofuel. Nat. Commun. 2, 483 (2011).
Westfall, P. J. et al. Production of amorphadiene in yeast, and its conversion to dihydroartemisinic acid, precursor to the antimalarial agent artemisinin. Proc. Natl Acad. Sci. USA 109, E111–E118 (2012).
Schalk, M. et al. Toward a biosynthetic route to sclareol and amber odorants. J. Am. Chem. Soc. 134, 18900–18903 (2012).
Ajikumar, P. K. et al. Isoprenoid pathway optimization for taxol precursor overproduction in Escherichia coli. Science 330, 70–74 (2010).
Alper, H., Jin, Y.-S., Moxley, J. F. & Stephanopoulos, G. Identifying gene targets for the metabolic engineering of lycopene biosynthesis in Escherichia coli. Metab. Eng. 7, 155–164 (2005).
Schwab, W., Fuchs, C. & Huang, F.-C. Transformation of terpenes into fine chemicals. Eur. J. Lipid Sci. Technol. 115, 3–8 (2013).
Zebec, Z. et al. Towards synthesis of monoterpenes and derivatives using synthetic biology. Curr. Opin. Chem. Biol. 34, 37–43 (2016).
Beller, H. R., Lee, T. S. & Katz, L. Natural products as biofuels and bio-based chemicals: fatty acids and isoprenoids. Nat. Prod. Rep. 32, 1508–1526 (2015).
Dudley, Q. M., Karim, A. S. & Jewett, M. C. Cell-free metabolic engineering: biomanufacturing beyond the cell. Biotechnol. J. 10, 69–82 (2015).
Chubukov, V. et al. Acute limonene toxicity in Escherichia coli is caused by limonene hydroperoxide and alleviated by a point mutation in alkyl hydroperoxidase AhpC. Appl. Environ. Microbiol. 81, 4690–4696 (2015).
Tomko, T. A. & Dunlop, M. J. Engineering improved bio-jet fuel tolerance in Escherichia coli using a transgenic library from the hydrocarbon-degrader Marinobacter aquaeolei. Biotechnol. Biofuels 8, 165 (2015).
Zhang, Y.-H. P. Production of biofuels and biochemicals by in vitro synthetic biosystems: opportunities and challenges. Biotechnol. Adv. 33, 1467–1483 (2015).
Guterl, J.-K. et al. Cell-free metabolic engineering: production of chemicals by minimized reaction cascades. ChemSusChem. 5, 2165–2172 (2012).
Dudley, Q. M., Anderson, K. C. & Jewett, M. C. Cell-free mixing of Escherichia coli crude extracts to prototype and rationally engineer high-titer mevalonate synthesis. ACS Synth. Biol. 5, 1578–1588 (2016).
Opgenorth, P. H., Korman, T. P. & Bowie, J. U. A synthetic biochemistry molecular purge valve module that maintains redox balance. Nat. Commun. 5, 4113 (2014).
Opgenorth, P. H., Korman, T. P. & Bowie, J. U. A synthetic biochemistry module for production of bio-based chemicals from glucose. Nat. Chem. Biol. 12, 393–395 (2016).
Welch, P. & Scopes, R. K. Studies on cell-free metabolism: ethanol production by a yeast glycolytic system reconstituted from purified enzymes. J. Biotechnol. 2, 257–273 (1985).
Ye, X. et al. Synthetic metabolic engineering-a novel, simple technology for designing a chimeric metabolic pathway. Microb. Cell Factories 11, 120 (2012).
Alissandratos, A., Caron, K., Loan, T. D., Hennessy, J. E. & Easton, C. J. ATP recycling with cell lysate for enzyme-catalyzed chemical synthesis, protein expression and PCR. ACS Chem. Biol. 11, 3289–3293 (2016).
Sato, M., Masuda, Y., Kirimura, K. & Kino, K. Thermostable ATP regeneration system using polyphosphate kinase from Thermosynechococcus elongatus BP-1 for d-amino acid dipeptide synthesis. J. Biosci. Bioeng. 103, 179–184 (2007).
Hoops, S. et al. COPASI—a COmplex PAthway SImulator. Bioinformatics 22, 3067–3074 (2006).
Smallbone, K. & Mendes, P. Large-scale metabolic models: from reconstruction to differential equations. Ind. Biotechnol. 9, 179–184 (2013).
Placzek, S. et al. BRENDA in 2017: new perspectives and new tools in BRENDA. Nucleic Acids Res. 45, D380–D388 (2016).
Korman, T. P. et al. A synthetic biochemistry system for the in vitro production of isoprene from glycolysis intermediates. Protein Sci. 23, 576–585 (2014).
Willrodt, C. et al. Engineering the productivity of recombinant Escherichia coli for limonene formation from glycerol in minimal media. Biotechnol. J. 9, 1000–1012 (2014).
Dunlop, M. J. et al. Engineering microbial biofuel tolerance and export using efflux pumps. Mol. Syst. Biol. 7, 487 (2011).
McKay, S. A. B. et al. Insect attack and wounding induce traumatic resin duct development and gene expression of (−)-pinene synthase in sitka spruce. Plant Physiol. 133, 368–378 (2003).
Srividya, N., Davis, E. M., Croteau, R. B. & Lange, B. M. Functional analysis of (4S)-limonene synthase mutants reveals determinants of catalytic outcome in a model monoterpene synthase. Proc. Natl Acad. Sci. USA 112, 3332–3337 (2015).
Algar, E. M. & Scopes, R. K. Studies on cell-free metabolism: ethanol production by extracts of Zymomonas mobilis. J. Biotechnol. 2, 275–287 (1985).
Kay, J. E. & Jewett, M. C. Lysate of engineered Escherichia coli supports high-level conversion of glucose to 2,3-butanediol. Metab. Eng. 32, 133–142 (2015).
Gibson, D. G. et al. Enzymatic assembly of DNA molecules up to several hundred kilobases. Nat. Methods 6, 343–345 (2009).
Acknowledgements
We thank members of the lab for helpful comments. This work was supported by DOE grant DE-FC02-02ER63421 and ARPA-E DE-AR0000556 to J.U.B.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Competing interests
The authors have formed a company, Invizyne Technologies, to expand and develop cell-free biomolecule production technologies.
Supplementary information
Supplementary Information
Supplementary Figures, Supplementary Tables, Supplementary Note, Supplementary References. (PDF 797 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Korman, T., Opgenorth, P. & Bowie, J. A synthetic biochemistry platform for cell free production of monoterpenes from glucose. Nat Commun 8, 15526 (2017). https://doi.org/10.1038/ncomms15526
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms15526
- Springer Nature Limited
This article is cited by
-
Expanding chemistry through in vitro and in vivo biocatalysis
Nature (2024)
-
ATP-free in vitro biotransformation of starch-derived maltodextrin into poly-3-hydroxybutyrate via acetyl-CoA
Nature Communications (2024)
-
Improving Aerobic Digestion of Food Waste by Adding a Personalized Microbial Inoculum
Current Microbiology (2024)
-
Investigating ethanol production using the Zymomonas mobilis crude extract
Scientific Reports (2023)
-
A synthetic cell-free 36-enzyme reaction system for vitamin B12 production
Nature Communications (2023)