Skip to main content
SpringerLink
Log in

Springback behavior of tailor rolled blank in U-shape forming

  • Published:
Journal of Iron and Steel Research International Aims and scope Submit manuscript

Abstract

The springback of tailor rolled blanks with quenching and partitioning steels was investigated. In order to find out the springback behavior and related influence factors for the novel sheets, both experimental and simulation methods have been used to compare and analyze the springback characteristics of equal thickness blanks and tailor rolled blanks in U-channel forming. From the results, the overall springback angles of tailor rolled blanks at thin and thick sides are respectively 106.79° and 99.705°, which are both lower than those of the corresponding equal thickness blanks. Due to the existence of the thickness transition zone, the stress distribution in thin and thick sides of blanks is changed. The location of dangerous region in thin side of tailor rolled blanks is closer to the end of side, and the thick side moved to the middle of straight wall, which are different with the equal thickness blanks. Afterwards, the released quantities of tangential stress and strain per unit section of blank are adopted to calculate relative springback angles and give novel evaluation criteria for qualitatively analyzing the amount of springback angles. By comparing the results, it shows that the tangential strain method is more suitable for the actual situation.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. P. J. Yan, J. T. Han, Z. Y. Jiang, H. J. Li, L. X. Liu, Adv. Mater. Res. 189–193 (2011) 3001–3006.

    Article  Google Scholar 

  2. S. Ying, H. Dong, Lect. Notes Electr. Eng. 195 (2013) 933–947.

    Article  Google Scholar 

  3. J. G. Speer, E. D. Moor, K. O. Findley, D. K. Matlock, B.C.D. Cooman, Metall. Mater. Trans. A 42 (2011) 3591–3601.

    Article  Google Scholar 

  4. E. J. Seo, L. Cho, Y. Estrin, B. C. D. Cooman, Acta. Mater. 113 (2016) 124–139.

    Article  Google Scholar 

  5. S. D. Chen, X. H. Liu, L. Z. Liu, Int. J. Mech. Sci. 100 (2015) 226–236.

    Article  Google Scholar 

  6. J. P. Li, Z. G. Liu, X. L. Bai, P. Li, J. Wuhan Univ. Technol. Mater. Sci. Ed. 32 (2017) 422–429.

    Article  Google Scholar 

  7. O. Engler, C. Schäfer, H. J. Brinkman, J. Brecht, P. Beiter, K. Nijhof, J. Mater. Process. Technol. 229 (2016) 139–148.

    Article  Google Scholar 

  8. L. B. Duan, G. Y. Sun, J. J. Cui, T. Chen, A. G. Cheng, Struct. Multidiscip. O 53 (2016) 321–338.

    Article  Google Scholar 

  9. R. Kopp, C. Wiedner, A. Meyer, Adv. Mater. Res. 6–8 (2005) 81–92.

    Article  Google Scholar 

  10. X. H. Liu, Q. L. Zhao, L. Z. Liu, Acta. Metall. Sin. 27 (2014) 483–493.

    Article  Google Scholar 

  11. X. H. Liu, G. J. Zhang, Y. Zhi, Sci. China 58 (2013) 1769–1774.

    Google Scholar 

  12. H. Kusuda, J. Mater. Process. Technol. 71 (1997) 134–140.

    Article  Google Scholar 

  13. M. Merklein, M. Johannes, M. Lechner, A. Kuppert, J. Mater. Process. Technol. 214 (2014) 151–164.

    Article  Google Scholar 

  14. G. X. Gu, G. Y. Sun, G. Y. Li, L. C. Mao, Q. Li, Struct. Multidiscip. O 48 (2013) 669–684.

    Article  Google Scholar 

  15. P. Beiter, P. Groche, Key. Eng. Mater. 473 (2011) 45–52.

    Article  Google Scholar 

  16. G. Hirth, D. H. Dávalos-Julca, Steel Res. Int. 83 (2012) 100–105.

    Article  Google Scholar 

  17. M. Merklein, M. Johannes, M. Lechner, A. Kupper, J. Mater. Process. Technol. 214 (2014) 151–164.

    Article  Google Scholar 

  18. H. W. Zhang, X. H. Liu, L. Z. Liu, P. Hu, J. L. Wu, J. Iron Steel Res. Int. 23 (2016) 185–189.

    Article  Google Scholar 

  19. D. J. Zhang, Z. S. Cui, X. Y. Ruan, Y. Q. Li, Comp. Mater. Sci. 38 (2007) No. 4, 707–715.

    Article  Google Scholar 

  20. M. Samuel, J. Mater. Process. Technol. 105 (2000) 382–393.

    Article  Google Scholar 

  21. W. Liu, Y. Y. Yang, Z. W. Xing, L. H. Zhao, J. Mater. Sci. Eng. 499 (2009) 325–328.

    Article  Google Scholar 

  22. J. Gau, P. Chris, M. Yu, J. Mater. Process. Technol. 191 (2007) 7–10.

    Article  Google Scholar 

  23. A. Ghaei, D. E. Green, A. Aryanpour, Mater. Des. 88 (2015) 461–470.

    Article  Google Scholar 

  24. J. W. Lee, M. G. Lee, F. Barlat, Int. J. Plasticity 29 (2012) 13–41.

    Article  Google Scholar 

  25. H. W. Zhang, L. Z. Liu, P. Hu, X. H. Liu, Acta. Metall. Sin. 25 (2012) 207–213.

    Google Scholar 

  26. H. W. Zhang, L. Z. Liu, P. Hu, X. H. Liu, J. Iron Steel Res. 19 (2012) No. 9, 8–12.

    Article  Google Scholar 

  27. X. J. Xu, Y. Q. Liu, W. Zhong, Fin. Elem. Anal. Des. 51 (2012) 49–58.

    Article  Google Scholar 

  28. K. Ahn, D. Yoo, M. H. Seo, S. Park, K. Chung, Met. Mater. Int. 15 (2009) 637–647.

    Article  Google Scholar 

  29. J. T. Gau, G. Principe, M. Yu, J. Mater. Process. Technol. 191 (2007) 7–10.

    Article  Google Scholar 

  30. K. M. Zhao, B. K. Chun, J. K. Lee, Fin. Elem. Anal. Des. 37 (2001) 117–130.

    Article  Google Scholar 

  31. W. J. Liu, Q. Liu, F. Ruan, Z. Y. Liang, H. Y. Qiu, J. Mater. Process. Technol. 187–188 (2007) 227–231.

    Article  Google Scholar 

  32. S. D. Chen, X. H. Liu, L. Z. Lin, Trans. Nonferrous Met. Soc. China 25 (2015) 3370–3380.

    Article  Google Scholar 

  33. R. M. Cleveland, A. K. Ghosh, Int. J. Plasticity 18 (2002) 769–785.

    Article  Google Scholar 

  34. L. P. Lei, S. Hwang, B. Kang, J. Mater. Process. Technol. 110 (2001) 70–77.

    Article  Google Scholar 

  35. T. Kuwabara, Int. J. Plasticity 23 (2007) 385–419.

    Article  Google Scholar 

  36. R. H. Wagoner, H. Lim, M. G. Lee, Int. J. Plasticity 45 (2013) 3–20.

    Article  Google Scholar 

  37. M. G. Lee, S. J. Kim, R. H. Wagoner, K. Chung, H. Y. Kim, Int. J. Plasticity 25 (2009) 70–104.

    Article  Google Scholar 

  38. W. D. Carden, L. M. Geng, D. K. Matlock, R. H. Wagoner, Int. J. Mech. Sci. 44 (2002) 79–101.

    Article  Google Scholar 

  39. M. Firat, B. Kaftanoglu, O. Eser, J. Mater. Process. Technol. 196 (2008) 135–148.

    Article  Google Scholar 

  40. L. Luo, A. K. Ghosh, J. Eng. Mater. Technol. 125 (2003) 237–246.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. State Key Laboratory of Rolling & Automation, Northeastern University, 110819, Shenyang, Liaoning, China

    Ri-huan Lu, Xiang-hua Liu Ph.D. (Prof.), Shou-dong Chen, Lu Feng & Xian-lei Hu

  2. School of Materials Science and Engineering, Northeastern University, 110819, Shenyang, Liaoning, China

    Xiang-hua Liu Ph.D. (Prof.) & Li-zhong Liu

Authors
  1. Ri-huan Lu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Xiang-hua Liu Ph.D.
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Shou-dong Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Lu Feng
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Xian-lei Hu
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Li-zhong Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Xiang-hua Liu Ph.D..

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Lu, Rh., Liu, Xh., Chen, Sd. et al. Springback behavior of tailor rolled blank in U-shape forming. J. Iron Steel Res. Int. 24, 787–794 (2017). https://doi.org/10.1016/S1006-706X(17)30118-8

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1016/S1006-706X(17)30118-8

Key words

Search

Navigation