Abstract
This paper mainly reports a proper selection of beam material for the step structured based RF MEMS switch. Generally, the performance of the device purely depends upon beam material used for the RF switch. There is a wide range of materials available for the beam layer which may change the performance of RF switch with their distinct material properties. Though various material selection methods are implemented earlier, among those methodologies Ashby’s material approach requires minimum execution steps for the beam selection based on various geometrical and performance indices. There are mainly three key performance indices like actuation voltage, S-parameters and residual stress by heat, are used to obtain the desired performance. The material selection in this work says that SU-8, PTFE followed by aluminum and gold are the more suitable materials for beam material selection for Step structured RF-MEMS switch. Due to fabrication complexity, SU-8 and PTFE are not considered for the beam layer. After the investigation, the above given two material (i.e.) Gold and Aluminum are preferable for the beam, owing to its high cost gold is not much preferable material for the beam. Therefore, Aluminum is good for the beam layer.
Similar content being viewed by others
References
R.J. Lee, et al. Military use of satellite communications, remote sensing, and global positioning systems in the war on terror. J. Air L. & Com. 79(1), 69–79 (2014)
M. Bonthu, A.K. Sharma, An investigation of dielectric material selection of RF-MEMS switches using Ashby’s methodology for RF applications. Microsyst. Technol. 24(4), 1803–1809 (2018)
N. Kolhare, MEMS switches for 0.1–40 GHz for Pico-satellite application. Microsyst. Technol. 21(4), 707–717 (2015)
M. Daneshmand, R.R. Mansour, Multiport MEMS-based waveguide and coaxial switches. IEEE Trans. Microw. Theory Tech. 53(11), 3531–3537 (2005)
Daneshmand M, Mansour RR (2011) RF MEMS satellite switch matrices, in IEEE Microwave Magazine, pp 02–109
D. Bansal, A. Kumar, A. Sharma, P. Kumar, K.J. Rangra, Design of novel compact anti-stiction and low insertion loss RF MEMS switch. Microsyst. Technol. 20(2), 337–340 (2014)
S. Lucyszyn, S. Pranonsatit, J.Y. Choi, R.W. Moseley, E.M. Yeatman, A.S. Holmes, Novel RF MEMS switches, in Asia-Pacific Microwave Conference, Bangkok (2007), pp. 1–4. https://doi.org/10.1109/apmc.2007.4554610
A.K. Ilkhechi, H. Mirzajani, E.N. Aghdam et al., A new electrostatically actuated rotary three-state DC-contact RF MEMS switch for antenna switch applications. Microsyst. Technol. (2017). https://doi.org/10.1007/s00542-015-2714-1
K. Khodadady, B.A. Ganji, Design and modeling of a novel RF MEMS series switch with low actuation voltage. Microsyst. Technol. (2016). https://doi.org/10.1007/s00542-015-2683-4
S. Gopalakrishnan, A. DasGupta, D.R. Nair, Novel RF MEMS capacitive switches with design flexibility for multi-frequency operation. J. Micromech. Microeng. 27(9), 09513 (2017). https://doi.org/10.1088/1361-6439/aa7d21
W. Simon, B. Schauwecker, A. Lauer, A. Wien, Designing a novel RF MEMS switch for broadband power applications, in Proceedings of the European Microwave Conference (Milan, Italy, 2002), pp. 519–522
A. Paldas, N. Gupta, Material selection and parameter characterization for Rf mems switches. Int. J. Mech. Prod. Eng. 1(3), 2320–2092 (2013)
M.F. Ashby, Materials selection in mechanical design, 2nd edn. (Butterworth-Heinemann, Oxford, 1999)
M.F. Ashby, Materials and the environment: Eco-informed material choice. (Butterworth-Heinemann, Oxford, 2009)
G.P. Reddy, N. Gupta, Material selection for microelectronic heat sinks: an application of the Ashby approach. Mater. Des. 31, 113–117 (2010)
G.M. Rebeiz, RF MEMS: theory, design, and technology, 3rd edn. (Wiley, Hoboken, 2003)
Acknowledgements
The Authors would like to thank to NMDC supported by NPMASS, National Institute of Technology, Silchar for providing the necessary computational tools.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Girija Sravani, K., Guha, K. & Srinivasa Rao, K. Analysis on Selection of Beam Material for Novel Step Structured RF-MEMS Switch used for Satellite Communication Applications. Trans. Electr. Electron. Mater. 19, 467–474 (2018). https://doi.org/10.1007/s42341-018-0068-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s42341-018-0068-y