Abstract
Purpose
A new in-vacuum three-dimensional Hall probe magnetic measurement system is under fabrication for characterizing the magnetic performance of the Cryogenic Permanent Magnet Undulator (CPMU). In order to fit the small gap (5 mm) of magnetic structure and vacuum environment, a small three-dimensional Hall probe has been manufactured. The angular and positional misalignment errors of the Hall sensors play an important role in the measurement accuracy of the CPMU. In order to minimize the misalignment errors, a method of calibrating angle error and relative assembly displacements of a three-dimensional Hall probe is carried out.
Methods
The angle error of Hall sensors will be calibrated by a standard dipole magnet and a five-dimensional Hall bench. The standard dipole magnet will generate a single direction and uniform magnetic field. And the five-dimensional Hall bench is used to rotate the Hall probe which is put in the center of magnet. Based on the relationship between angle and magnetic field strength, the angle error of each Hall sensor will be obtained. The relative position between the sensitive areas of the Hall sensors will be calibrated by a two-dimensional magnetic field undulator section. Based on Maxwell’s equations, through the calculation of measurement magnetic field strength, the relative assembly displacements of the three Hall sensors can be derived.
Results
The details of the calibration methods and the data processing of angle error and relative assembly displacements of a three-dimensional Hall probe are presented. The three-dimensional magnetic fields of a cryogenic permanent magnet undulator can be received accurately by correcting these angle errors and position errors of Hall sensors.
Conclusions
This paper illustrates the relative position and angle calibration procedures and the data processing of a three-dimensional Hall probe. Now the design of a smaller Hall probe is in process. The calibration of the angle errors and position errors will be carried out after the fabrication of the standard dipole magnet.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Change history
13 March 2018
The original version of these four articles as below unfortunately contained a mistake. The category “Review” was incorrect. The correct category is “Original Paper”.
References
X. Jiang, J.Q. WANG, Q. QIN, Chinese high energy photon source and the test facility[J]. Sci. Sinica Phys. Mech. Astron. 44(10), 1075 (2014)
W. Lei, W. Xiao-Long, L. Chun-Hua et al., Preliminary R&D of vibrating wire alignment technique for HEPS[J]. Chin. Phys. C 39(8), 087002 (2015)
S. C. Sun and al., Mechanical design of a cryogenic permanent magnet undulator at IHEP. in Proceeding of the IPAC17, 8th International Particle Accelerator Conference, May 14–19, Copenhagen, Denmark, TUPAB066, (2017)
L. Zhang and al., Design of the CPMU vacuum system at the HEPS. in Proceeding of the IPAC17, 8th International Particle Accelerator Conference, May 14–19, Copenhagen, Denmark, TUPAB068, (2017)
Y. Yang, H. Lu, S. Sun et al., Field Error Correction Considerations of Cryogenic Permanent Magnet Undulator (CPMU) for High Energy Photon Source Test Facility (HEPS-TF)[C]. in 7th International Particle Accelerator Conference (IPAC’16), Busan, Korea, May 8–13, JACOW, Geneva, Switzerland, 4038–4040, (2016)
H. H. Lu and al., Development of a PrFeB cryogenic permanent magnet undulator (CPMU) prototype At IHEP. in Proceeding of the IPAC17, 8th International Particle Accelerator Conference, May 14–19, Copenhagen, Denmark, TUPAB064, (2017)
C. Kitegi, Development of a Cryogenic Permanent Magnet Undulator at the ESRF[D] (Université Joseph Fourier, Grenoble, 2009)
W. Chen, C T. Shi, H H. Lu, et al., Development of insertion devices measurement system at IHEP[J]
J. Campmany, J. Marcos, V. Massana, New improvements in magnetic measurements laboratory of the ALBA synchrotron facility[J]. Phys.Proced. 75, 1214–1221 (2015)
J. Marcos, J. Campmany, V. Massana, et al., Construction & commissioning of a 3D hall probe bench for insertion devices measurements at ALBA Synchrotron Light Source[C]. Contribution to the International Magnetic Measurements Workshop IMMW15. Fermi National Accelerator Lab. (2007)
Z. Wolf, Hall element angle calibrations for the delta undulator LCLS-TN-13-10
J. Chavanne, P. Elleaume, Technology of insertion devices[J]. Undulators Wigglers Appl. 1, 148–213 (2003)
J. Campmany , J. Marcos , V. Massana , et al., Status of magnetic measurements at ALBA[C]. in International Magnetic Measurements Workshop IMMW18, (2013)
Acknowledgements
The authors would like to acknowledge Dr. Shu Guan, Dr. Wu Lei, Dr. Gu Kuixiang and Dr. Tang Zheng for great helpful discussion and suggestion.
Author information
Authors and Affiliations
Corresponding author
Additional information
A correction to this article is available online at https://doi.org/10.1007/s41605-018-0036-4.
Rights and permissions
About this article
Cite this article
Gong, LL., Chen, W., Kang, W. et al. Hall sensor angle error and relative position calibrations for cryogenic permanent magnet undulator of high energy photon source test facility (HEPS-TF). Radiat Detect Technol Methods 1, 17 (2017). https://doi.org/10.1007/s41605-017-0018-y
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1007/s41605-017-0018-y
Keywords
- Magnetic measurement system
- Cryogenic permanent magnet undulator
- Three-dimensional Hall probe
- Calibration of Hall probe