Skip to main content
SpringerLink
Log in

Effect of heat treatment on the impact toughness and thermal properties of the AlSi10Mg alloy manufactured by laser powder bed fusion

  • Full Research Article
  • Published:
Progress in Additive Manufacturing Aims and scope Submit manuscript

Abstract

The objective of this work was to investigate the impact toughness and thermal properties of laser powder bed fusion AlSi10Mg alloy under the influence of different heat treatment conditions viz. T6 and direct aging (DA). At room temperature, the tensile results showed that the DA alloy possessed higher yield and ultimate tensile strengths whereas, the T6 alloy had lower yield strength and ultimate tensile strength as expected. Impact energy absorption value of DA alloy was higher than the T6 alloy; however, lower than the as-built condition. Fractographic examination after impact toughness test revealed that crack propagated mainly along the molten pool boundary and high-density precipitated Si particles were also observed inside the fine dimple in DA alloy. Variation in microstructural morphology, cellular structure, and the distribution of Si particles due to heat treatments substantially affected impact toughness and thermal properties. The thermal properties such as heat capacity, thermal diffusivity, and thermal conductivity as a function of different heat treatment conditions were suggested. DA specimen had the lowest thermal conductivity and thermal diffusivity than as-built and T6 specimens. It indicated that heat transfer was hindered by the fine Si particles present in the Al matrix and Si-rich region, owing to the low thermal conductivity of Si. Based on the above results, the controlling method for toughness and thermal conductivity of selective laser melted AlSi10Mg alloy was also discussed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

Data availability

The datasets used and analyzed during the current investigation are available from the corresponding author on reasonable request.

References

  1. Frazier WE (2014) Metal additive manufacturing: a review. J Mater Eng Perform 23:1917–1928. https://doi.org/10.1007/s11665-014-0958-z

    Article  Google Scholar 

  2. Prashanth KG, Scudino S, Klauss HJ, Surreddi KB et al (2014) Microstructure and mechanical properties of Al-12Si produced by selective laser melting: effect of heat treatment. Mater Sci Eng A 590:153–160. https://doi.org/10.1016/j.msea.2013.10.023

    Article  Google Scholar 

  3. Tonelli L, Liverani E, Valli G, Fortunato A, Ceschini L (2020) Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting. Int J Adv Manuf Technol 106:371–383. https://doi.org/10.1007/s00170-019-04641-x

    Article  Google Scholar 

  4. Yasa E, Kruth JP (2011) Microstructural investigation of selective laser melting 316L stainless steel parts exposed to laser re-melting. Procedia Eng 19:389–395. https://doi.org/10.1016/j.proeng.2011.11.130

    Article  Google Scholar 

  5. Zhang J, Song B, Wei Q, Bourell D, Shi Y (2019) A review of selective laser melting of aluminum alloys: processing, microstructure, property and developing trends. J Mater Sci Technol 35:270–284. https://doi.org/10.1016/j.jmst.2018.09.004

    Article  Google Scholar 

  6. Wu J, Wang X, Wang W, Attallah M, Loretto M (2016) Microstructure and strength of selectively laser melted AlSi10Mg. Acta Mater 117:311–320. https://doi.org/10.1016/j.actamat.2016.07.012

    Article  Google Scholar 

  7. Brandl E, Heckenberger U, Holzinger V, Buchbinder D (2012) Additive manufactured AlSi10Mg samples using selective laser melting (SLM): microstructure, high cycle fatigue, and fracture behavior. Mater Des 34:159–169. https://doi.org/10.1016/j.matdes.2011.07.067

    Article  Google Scholar 

  8. Aboulkhair NT, Maskery I, Tuck C, Ashcroft I, Everitt NM (2016) The microstructure and mechanical properties of selectively laser melted AlSi10Mg: the effect of a conventional t6-like heat treatment. Mater Sci Eng A 667:139–146. https://doi.org/10.1016/j.msea.2016.04.092

    Article  Google Scholar 

  9. Tradowsky U, White J, Ward R, Read N, Reimers W, Attallah M (2016) Selective laser melting of AlSi10Mg: influence of post-processing on the microstructural and tensile properties development. Mater Des 105:212–222. https://doi.org/10.1016/j.matdes.2016.05.066

    Article  Google Scholar 

  10. Liu Y, Liu Z, Jiang Y, Wang G, Yang Y, Zhang L (2018) Gradient in microstructure and mechanical property of selective laser melted AlSi10Mg. J Alloy Compd 735:1414–1421. https://doi.org/10.1016/j.jallcom.2017.11.020

    Article  Google Scholar 

  11. Cerri E, Ghio E, Bolelli G (2021) Effect of the distance from build platform and post-heat treatment of AlSi10Mg alloy manufactured by single- and multi-laser selective laser melting. J Mater Eng Perform 30:4981–4992. https://doi.org/10.1007/s11665-021-05577-8

    Article  Google Scholar 

  12. Butler C, Babu S, Lundy R, O’Reilly Meehan R, Punch J, Jeffers N (2021) Effects of processing parameters and heat treatment on thermal conductivity of additively manufactured AlSi10Mg by selective laser melting. Mater Charact 173:110945. https://doi.org/10.1016/j.matchar.2021.110945

    Article  Google Scholar 

  13. Seifi M, Salem A, Beuth J, Harrysson O, Lewandowski JJ (2016) Overview of materials qualification needs for metal additive manufacturing. JOM 68:747–764. https://doi.org/10.1007/s11837-015-1810-0

    Article  Google Scholar 

  14. Kittel C (1976) Introduction to solid state physics. 5th edn. John Wiley & Son, Inc New York, New York, p 126–146

  15. Cingi C, Rauta V, Suikkanen E, Orkas J (2012) Effect of heat treatment on thermal conductivity of aluminum die casting alloys. Adv Mater Res 538–541:2047–2052. https://doi.org/10.4028/www.scientific.net/AMR.538-541.2047

    Article  Google Scholar 

  16. Lumley RN (2018) Thermal conductivity of aluminium high-pressure die castings. Fundamentals of aluminium metallurgy. Elsevier, Amsterdam, pp 217–247

    Chapter  Google Scholar 

  17. Kaschnitz E, Funk W, Pabel T (2014) Electrical resistivity measured by millisecond pulse-heating in comparison to thermal conductivity of the aluminium alloy Al-7Si-0.3 Mg at elevated temperature. High Temp Press 43:175–191

    Google Scholar 

  18. Choi SW, Kim YM, Kim YC (2019) Influence of precipitation on thermal diffusivity of Al-6Si-0.4 Mg-0.9Cu-(Ti) alloys. J Alloys Compd 775:132–137. https://doi.org/10.1016/j.jallcom.2018.10.068

    Article  Google Scholar 

  19. Yan C, Hao L, Hussein A, Young P, Huang J, Zhu W (2015) Microstructure and mechanical properties of aluminum alloy cellular lattice structure manufactured by direct metal laser sintering. Mater Sci Eng A 628:238–246. https://doi.org/10.1016/j.msea.2015.01.063

    Article  Google Scholar 

  20. Li W, Li S, Liu J, Zhang A, Zhou Y, Wei Q, Yan C, Shi Y (2016) Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties and fracture mechanism. Mater Sci Eng A 663:116–125. https://doi.org/10.1016/j.msea.2016.03.088

    Article  Google Scholar 

  21. Fiocchi J, Tuissi A, Bassani P, Biffi CA (2017) Low temperature annealing dedicated to AlSi10Mg selective laser melting products. J Alloy Comp 695:3402. https://doi.org/10.1016/j.jallcom.2016.12.019

    Article  Google Scholar 

  22. Strumza E, Yeheskel O, Hayun S (2019) The effect of texture on the anisotropy of thermophysical properties of additively manufactured AlSi10Mg. Addit Manuf 29:100762. https://doi.org/10.1016/j.addma.2019.06.013

    Article  Google Scholar 

  23. Selo R, Catchpole-Smith S, Maskery I, Ashcroft I, Tuck C (2020) On the thermal conductivity of AlSi10Mg and lattice structures made by laser powder bed fusion. Addit Manuf 34:101214. https://doi.org/10.1016/j.addma.2020.101214

    Article  Google Scholar 

  24. Yang P, Deibler LA, Bradley DR, Stefan DK, Carroll JD (2018) Microstructure evolution and thermal properties of an additively manufactured, solution treatable AlSi10Mg part. J Mater Res 33:1–13. https://doi.org/10.1557/jmr.2018.405

    Article  Google Scholar 

  25. Girelli L, Giovagnoli M, Tocci M et al (2019) Evaluation of the impact behaviour of AlSi10Mg alloy produced using laser additive manufacturing. Mater Sci Eng A 748:38–51. https://doi.org/10.1016/j.msea.2019.01.078

    Article  Google Scholar 

  26. Raus AA, Wahab MS, Ibrahim M, Kamarudin K, Ahmed A, Shamsudin S (2017) Mechanical and physical properties of AlSi10Mg processed through selective laser melting. AIP Conf Proc 1831:020027. https://doi.org/10.1063/1.4981168

    Article  Google Scholar 

  27. Giovagnoli M, Tocci M, Fortini A, Merlin M, Ferroni M, Migliori A, Pola A (2021) Effect of different heat-treatment routes on the impact properties of an additively manufactured AlSi10Mg alloy. Mater Sci Eng A 802:140671. https://doi.org/10.1016/j.msea.2020.140671

    Article  Google Scholar 

  28. Park TH, Baek MS, Hyer H, Sohn Y, Lee KA (2021) Effect of direct aging on the microstructure and tensile properties of AlSi10Mg alloy manufactured by selective laser melting process. Mater Charact 176:111113. https://doi.org/10.1016/j.matchar.2021.111113

    Article  Google Scholar 

  29. Chen KJ, Hung FY, Lui TS, Tsai CL (2020) Improving the applicability of wear-resistant Al–10Si–0.5 Mg alloy obtained through selective laser melting with T6 treatment in high-temperature, and high-wear environments. J Mater Res Technol 9:9242–9252. https://doi.org/10.1016/j.jmrt.2020.06.078

    Article  Google Scholar 

  30. Kempen K, Thijs L, Van Humbeeck J, Kruth JP (2012) Mechanical properties of AlSi10Mg produced by selective, laser melting. Phys Procedia 39:439–446. https://doi.org/10.1016/j.phpro.2012.10.059

    Article  Google Scholar 

  31. Rosenthal I, Stern A, Frage N (2017) Strain rate sensitivity and fracture mechanism of AlSi10Mg parts produced by selective laser melting. Mater Sci Eng A 682:509–517. https://doi.org/10.1016/j.msea.2016.11.070

    Article  Google Scholar 

  32. Suryawanshi J, Prashanth K, Scudino S, Eckert J, Prakash O, Ramamurthy U (2016) Simultaneous enhancements of strength and toughness in an Al-12Si alloy synthesized using selective laser melting. Acta Mater 115:285–294. https://doi.org/10.1016/j.actamat.2016.06.009

    Article  Google Scholar 

  33. Dai D, Gu D, Zhang H, Xiong J, Ma C, Hong C, Poprawe R (2018) Microstructure and tensile properties of selective laser melting additive manufactured aluminum-based parts. Opt Laser Technol 99:91–100. https://doi.org/10.1016/j.optlastec.2017.08.015

    Article  Google Scholar 

  34. Silbernagel C, Ashcroft I, Dickens P, Galea M (2018) Electrical resistivity of additively manufactured AlSi10Mg for use in electric motors. Addit Manuf 21:395–403. https://doi.org/10.1016/j.addma.2018.03.027

    Article  Google Scholar 

  35. Kim MS (2021) Effects of processing parameters of selective laser melting process on thermal conductivity of AlSi10Mg alloy. Materials 14:2410. https://doi.org/10.3390/ma14092410

    Article  Google Scholar 

  36. Maradiaga DM, Mishin OV, Engelbrech K (2020) Thermal properties of selectively laser-melted AlSi10Mg products with different densities. J Mater Eng Perform 29:7125–7130. https://doi.org/10.1007/s11665-020-05192-z

    Article  Google Scholar 

  37. Kimura T, Nakamoto T, Mizuno M, Araki H (2017) Effect of silicon content on densification, mechanical and thermal properties of AlxSi binary alloys fabricated using selective laser melting. Mater Sci Eng A 682:593–602. https://doi.org/10.1016/j.msea.2016.11.059

    Article  Google Scholar 

  38. Thijs L, Kempen K, Kruth J, Humbeeck JV (2013) Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater 61:1809–1819. https://doi.org/10.1016/j.actamat.2012.11.052

    Article  Google Scholar 

  39. Kempf A, Hilgenberg K (2020) Influence of sub-cell structure on the mechanical properties of AlSi10Mg manufactured by laser powder bed fusion. Mat Sci Eng A 776:138976. https://doi.org/10.1016/j.msea.2020.138976

    Article  Google Scholar 

  40. Maamoun AH, Xue YF, Elbestawi MA, Veldhuis SC (2019) The effect of selective laser melting process parameters on the microstructure and mechanical properties of Al6061 and AlSi10Mg alloys. Materials 12:12. https://doi.org/10.3390/ma12010012

    Article  Google Scholar 

  41. Taarea D, Bakhtiyarov SI (2004) General physical properties. In: Gale WF, Totemeier TC (eds) Smithells metals reference book, 8th edn. Butterworth-Heinemann, Oxford, pp 1–45

    Google Scholar 

Download references

Acknowledgements

This work was supported by the National Research Foundation of Korea (NRF) Grant funded by the Korean Government (MSIP) (No. Grant Number – NRF-2022R1A5A1030054).

Author information

Authors and Affiliations

  1. Department of Materials Science and Engineering, Inha University, Incheon, 22212, Republic of Korea

    R. Kreethi & Kee-Ahn Lee

  2. Advanced Materials Processing and Analysis Center, University of Central Florida, Orlando, FL, 32816, USA

    Yongho Sohn

Authors
  1. R. Kreethi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Yongho Sohn
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Kee-Ahn Lee
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

Conceptualization, investigation, methodology, writing—original draft: RK; validation, funding acquisition, resources: YS; supervision, conceptualization, writing—review and editing: K-AL. The authors have read and agreed to the published version of the manuscript.

Corresponding author

Correspondence to Kee-Ahn Lee.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Kreethi, R., Sohn, Y. & Lee, KA. Effect of heat treatment on the impact toughness and thermal properties of the AlSi10Mg alloy manufactured by laser powder bed fusion. Prog Addit Manuf 9, 543–551 (2024). https://doi.org/10.1007/s40964-023-00473-0

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40964-023-00473-0

Keywords

Search

Navigation