Abstract
Purpose
Scoliosis patients are normally treated either by surgery or by wearing spinal braces for correction. A spinal brace may be made of rigid materials or soft materials. The use of soft materials for braces, such as fabric materials, is one alternative being used to develop soft braces because textile materials could be comfortable and provide high compliance with users. However, there are no studies about how to provide treatment/prevention of scoliosis using various textile fabric materials to fabricate a soft brace. Thus, this study aims to study the effect of the physical and mechanical properties of textile fabric materials used in a soft brace for the treatment/prevention of scoliosis using finite element model (FEM) simulation.
Methods
This study covers the following stages: a) development of a geometric model of scoliosis through finite element modelling using 2D X-ray clinical data; b) selection of appropriate textile materials to be used in a soft brace by measuring physical and mechanical properties; and c) determination of the performance of the soft brace fabricated with various textile fabric materials in terms of the Cobb angle through FEM simulation.
Results
The results of this study found that the textile fabric materials made of polyester with sandwich mesh and elastic band in parallel layer provides good softness and air permeability and it has a high capability to provide the treatment of scoliosis in terms of Cobb angle changed by 14.4% using FEM simulation.
Conclusion
Such design of soft brace with textile fabric materials provides more comfortable for patients in wearing for long time. It is worthwhile for rehabilitation professionals to design appropriate textile-based soft braces for scoliosis.
Similar content being viewed by others
Data Availability
(data transparency): Collected data and materials are available.
Code Availability
Software application.
References
Weiss, H. R., & Weiss, G. M. (2009). Brace treatment during pubertal growth spurt in girls with idiopathic scoliosis (is): a prospective trial comparing two different concepts. Pediatric Rehabilitation,8(3), 199–206.
Weiss, H.-R., & Werkmann, M. (2012). Soft braces in the treatment of Adolescent Idiopathic Scoliosis (AIS) – Review of the literature and description of a new approach. Scoliosis,7, 11. https://doi.org/10.1186/1748-7161-7-11.
Rizza, R., Liu, X. C., Thometz, J., & Tassone, C. (2015). Comparison of biomechanical behavior between a cast material torso jacket and a polyethylene based jacket. Scoliosis,10(Suppl 2), S15–S15.
Gutman, G., Benoit, M., Joncas, J., Beauséjour, M., Barchi, S., Labelle, H., et al. (2016). The effectiveness of the spinecor brace for the conservative treatment of adolescent idiopathic scoliosis comparison with the boston brace. Spine Journal Official Journal of the North American Spine Society,16(5), 626–631.
Martin, M., Suzanne, B., Jonathan, M., & Jennifer, F. (2016). The use of dynamic elastomeric fabric orthosis suits as an orthotic intervention in the management of children with neuropathic onset scoliosis: a retrospective audit of routine clinical case notes. Scoliosis & Spinal Disorders,11(1), 1–10.
Matthews, M., & Crawford, R. (2006). The use of dynamic lycra orthosis in the treatment of scoliosis: a case study. Prosthetics & Orthotics International,30(2), 174.
Cobetto, N., Aubin, C. E., Clin, J., Le, M. S., Desbiens-Blais, F., Labelle, H., et al. (2014). Braces optimized with computer-assisted design and simulations are lighter, more comfortable, and more efficient than plaster-cast braces for the treatment of adolescent idiopathic scoliosis. Spine Deform,2(4), 276–284.
Duke, K., Aubin, C. E., Dansereau, J., & Labelle, H. (2008). Computer simulation for the optimization of patient positioning in spinal deformity instrumentation surgery. Medical & Biological Engineering & Computing,46(1), 33–41.
Huynh, A. M., Aubin, C. E., Mathieu, P. A., & Labelle, H. (2007). Simulation of progressive spinal deformities in duchenne muscular dystrophy using a biomechanical model integrating muscles and vertebral growth modulation. Clinical Biomechanics,22(4), 392–399.
Wang, W., Baran, G. R., Betz, R. R., Samdani, A. F., Pahys, J. M., & Cahill, P. J. (2014). The use of finite element models to assist understanding and treatment for scoliosis: a review paper. Spine Deformity,2(1), 10–27.
Goel, V. K., Monroe, B. T., Gilbertson, L. G., & Brinckmann, P. (1995). Interlaminar shear stresses and laminae separation in a discrete finite element analysis of the l3–l4 motion segment subjected to axial compressive loads. Spine,20(6), 689–698.
Wang, Z., Liu, Z., Wang, Z., Wang, C., & Ming, Y. E. (2008). Development of finite element model for the scoliotic spine and its parameters optimization. Beijing Biomedical Engineering.
Clin, J., Aubin, C. É., Parent, S., & Labelle, H. (2011). Biomechanical modeling of brace treatment of scoliosis: effects of gravitational loads. Medical & Biological Engineering & Computing,49(7), 743.
https://caelinux.org/wiki/index.php/Contrib:KeesWouters/bc/rbe3
Wang, T., & Wu, H. N. (2015). Introduction to the Thermal and Humid Comfort and Evaluation Method. Journal of China Fiber Inspection,10, 74–76.
You, F., Wang, J. M., Luo, X. N., Li, Y., & Zhang, X. (2002). Garment's pressure sensation (1): subjective assessment and predictability for the sensation. International Journal of Clothing Science & Technology,14(5), 307–316.
Nie, W. Z., Ye, M., Liu, Z. D., & Wang, C. T. (2009). The patient-specific brace design and biomechanical analysis of adolescent idiopathic scoliosis. Journal of Biomedical Engineering,131(4), 041007.
Zhou, J. Y., Li, Y., Lam, J., & Cao, X. (2018). The poisson ratio and modulus of elastic knitted fabrics. Textile Research Journal.,80(18), 1965–1969.
Horng, M., Kuok, C., Fu, M., Lin, C., & Sun, Y. (2019). Cobb Angle Measurement of Spine from X-Ray Images Using Convolutional Neural Network. Computational and Mathematical Methods in Medicine,2019, 6357171.
Lechner, R., Putzer, D., Dammerer, D., Liebensteiner, M., Bach, C., & Thaler, M. (2017). Comparison of two- and three-dimensional measurement of the Cobb angle in scoliosis. International Orthopaedics,41(5), 957–962.
Suwannarat, P., Wattanapan, P., Wiyanad, A., Chokphukiao, P., Wilaichit, S., & Amatachaya, S. (2017). Reliability of novice physiotherapists for measuring Cobb angle using a digital method. Hong Kong Physiotherapy Journal,37, 34–38.
Giannoglou, V., & Stylianidis, E. (2016). Review of advances in Cobb angle calculation and image-based modelling techniques for spinal deformities. ISPRS Annals of Photogrammetry, Remote Sensing and Spatial Information Sciences, III-5, 129–135.
Funding
This study was financially supported by the Hong Kong Polytechnic University Research Grant (Number: YBFA and YBGU).
Author information
Authors and Affiliations
Contributions
Chi Leung Hui designed the experiments, performed data analysis, and made report writing. Jinli Piao carried out the experiments, supported analysis and made report writing. MS Wong supported the collection of 2D X-ray data. ZhiYong Chen developed the finite element model.
Corresponding author
Ethics declarations
Conflicts of interest
The authors declares that they have no conflict of interest.
Rights and permissions
About this article
Cite this article
Hui, Cl., Piao, J., Wong, M. et al. Study of Textile Fabric Materials used in Spinal Braces for Scoliosis. J. Med. Biol. Eng. 40, 356–371 (2020). https://doi.org/10.1007/s40846-020-00516-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40846-020-00516-9