Abstract
The global transport sector is heavily dependent on fossil fuels as a vital source of energy. This has adversely affected the climate. This climate change necessitates that technologies employing renewable and clean energy should be utilized in the global transportation sector. To address this issue, in this study, a small wind turbine was implemented on a vehicle, such that it is able to capture the air when the vehicle is in motion to generate the required energy to run the vehicle. Consequently, theoretical modeling and experimental calculation were conducted to confirm the utilization of wind by the turbine of the running vehicle to generate electricity through the conversion process of its electrical subsystem, thereby powering the vehicle as a self-sufficient energy mechanism that can be commercialized. The results show that a car moving at 10 kph produces 8 kWh, for an average wind speed of 2 kph. As a standard car requires 20 kWh to get fully energized, the results indicate that it is possible to fully charge the car and run it for 200 kilom if the car runs at 10 kph for two hours during charging. Consequently, if the car runs at 60 kph, it will take require 20 min to get fully charged and run for the same distance. The findings of this research suggest that the large-scale adoption of wind energy, which is completely clean and available in abundance, to run vehicles can be an innovative solution to meet the energy demand of the global transportation sector.
Similar content being viewed by others
References
Touaiti B, Azza HB, Jemli M (2016) A MRAS observer for sensorless control of wind-driven doubly fed induction generator in remote areas. In: Proceedings of the 17th international conference on sciences and techniques of automatic control and computer engineering (STA); 2016 Dec 19–21; Sousse, Tuisia. https://doi.org/10.1109/STA.2016.7951979.
Ribeiro E, Monteiro A, Cardoso AJM, Boccaletti C (2014) Fault tolerant small wind power system for telecommunications with maximum power extraction. In: Proceedings of the IEEE 36th international telecommunications energy conference (INTELEC); 2014 Sept 28–Oct 2; Vancouver, Canada. https://doi.org/10.1109/INTLEC.2014.6972225.
Junyent-Ferre A, Gomis-Bellmunta O, Sumperb A, Salad M, Mata M (2010) Modeling and control of the doubly fed induction generator wind turbine. Simulat Model Pract Theor 18:1365–1381. https://doi.org/10.1016/j.simpat.2010.05.018
Singh J, Ouhrouche M (2011) MPPT control methods in wind energy conversion systems. In: Carriveau R (ed) Fundamental and advanced topics in wind power. InTech, Rijeka, pp 339–360
Kerrouche K, Mezouar A, Belgacem K (2013) Decoupled control of doubly fed induction generator by vector control for wind energy conversion system. Energy Proc 42:239–248. https://doi.org/10.1016/j.egypro.2013.11.024
Hossain MF (2019) Flying transportation technology. Elsevier, Amsterdam
Falehi AD (2017) Augment dynamic and transient capability of DFIG using optimal design of NIOPID based DPC strategy. Environ Prog Sustain 37:1491–1502. https://doi.org/10.1002/ep.12811
Mwaniki DJ, Lin H, Dai Z (2017) A condensed introduction to the doubly fed induction generator wind energy conversion systems. J Eng. https://doi.org/10.1155/2017/2918281
Hossain MF (2017) Design and construction of ultra-relativistic collision PV panel and its application into building sector to mitigate total energy demand. J Build Eng 9:147–154. https://doi.org/10.1016/j.jobe.2016.12.005
Hossain MF, Fara N (2016) Integration of wind into running vehicles to meet its total energy demand. Energy Ecol Environ 2:35–48. https://doi.org/10.1007/s40974-016-0048-1
Ling Y (2018) A fault ride through scheme for doubly fed induction generator wind turbine. Aust J Electr Electron Eng 15:71–79. https://doi.org/10.1080/1448837X.2018.1525172
Zin AABM, Mahmoud HAP, Khairuddin AB, Jahanshaloo L, Shariatu O (2013) An overview on doubly fed induction generators’ controls and contributions to wind-based electricity generation. Renew Sustain Energy Rev 27:692–708. https://doi.org/10.1016/j.rser.2013.07.010
Zohoori A, Vahedi A, Noroozi MA, Meo S (2016) A new outer-rotor flux switching permanent magnet generator for wind farm applications: flux switching permanent magnet generator for wind farm applications. Wind Energy 20:3–17. https://doi.org/10.1002/we.1986
Gaillard A, Poure P, Saadate S (2010) Reactive power compensation and active filtering capability of WECS with DFIG without any over-rating. Wind Energy 13:603–614. https://doi.org/10.1002/we.381
Mani P, Lee J-H, Kang K-W, Joo YH (2019) Digital controller design via LMIs for direct-driven surface mounted PMSG-based wind energy conversion system. IEEE Trans Cybern. https://doi.org/10.1109/TCYB.2019.2923775(Epub ahead of print)
Ouassaid M, Elyaalaoui K, Cherkaoui M (2015) Reactive power capability of squirrel cage asynchronous generator connected to the grid. In: Proceedings of the 3rd international renewable and sustainable energy conference (IRSEC); 2015 Dec. 10–13; Marrakech, Morocco. https://doi.org/10.1109/IRSEC.2015.7455003.
Abulizi M, Peng L, Francois B, Li Y (2014) Performance analysis of a controller for doubly-fed induction generators based wind turbines against parameter variations. Int Rev Electr Eng 9:262–269. https://doi.org/10.15866/iree.v9i2.1797
Hamoud F, Doumbia ML, Cheriti A (2014) Hybrid PI-Sliding mode control of a voltage source converter based STATCOM. In: Proceedings of the 16th international power electronics and motion control conference and exposition; 2014 Sept 21–24; Antalya, Turkey. https://doi.org/10.1109/EPEPEMC.2014.6980571.
Boumassata A, Kerdoun D, Madaci M (2015) Grid power control based on a wind energy conversion system and a flywheel energy storage system. In: IEEE EUROCON 2015: proceedings of the international conference on computer as a tool (EUROCON); 2015 Sept 8–11; Salamanca, Spain. https://doi.org/10.1109/EUROCON.2015.7313699.
Kerrouche K, Mezouar A, Boumedien L (2013) A simple and efficient maximized power control of DFIG variable speed wind turbine. In: Proceedings of the 3rd International conference on systems and control; 2013 Oct 29–31; Algiers, Algeria. https://doi.org/10.1109/ICoSC.2013.6750963.
Upadhyay VC, Sandhu KS (2018) Reactive power management of wind farm using STATCOM. In: Proceedings of the international conference on emerging trends and innovations in engineering and technological research (ICETIETR); 2018 July 11–13; Ernakulam, India. https://doi.org/10.1109/ICETIETR.2018.8529090.
Ghedamsi K, Aouzellag D (2010) Improvement of the performances for wind energy conversions systems. Int J Electr Power Energy Syst 32:936–945. https://doi.org/10.1016/j.ijepes.2010.02.012
Touaiti B, ben Azza H, Jemli M (2019) Control scheme for stand-alone DFIG feeding an isolated load. In: Proceedings of the 10th international renewable energy congress (IREC); 2019 March 26–28; Sousse, Tunisia. https://doi.org/10.1109/IREC.2019.8754515.
Rani MD, Kumar MS (2017) Development of doubly fed induction generator equivalent circuit and stability analysis applicable for wind energy conversion system. In: Proceedings of the International Conference on Recent Advances in Electronics and Communication Technology (ICRAECT); 2017 March 16–17; Bangalore, India. https://doi.org/10.1109/ICRAECT.2017.34.
Bento F, Cardoso AJM (2018) A comprehensive survey on fault diagnosis and fault tolerance of DC–DC converters. Chin J Electr Eng 4:1–12. https://doi.org/10.23919/CJEE.2018.8471284
Saeed MSR, Mohamed EEM, Sayed MA (2016) Design and analysis of dual rotor multi-tooth flux switching machine for wind power generation. In: Proceedings of the 18th international middle east power systems conference (MEPCON); 2016 Dec. 27–29; Cairo, Egypt. https://doi.org/10.1109/MEPCON.2016.7836937.
Rad MAV, Ghasempour R, Rahdan P, Mousavi S, Arastounia M (2019) Techno-economic analysis of a hybrid power system based on the cost-effective hydrogen production method for rural electrification, a case study in Iran. Energy. https://doi.org/10.1016/j.energy.2019.116421
Karthikeyan R, Parvathy AK (2015) Peak load reduction in micro smart grid using non-intrusive load monitoring and hierarchical load scheduling. In: Proceedings of the 2015 international conference on smart sensors and systems (IC-SSS); 2015 Dec 21–23; Bangalore, India; https://doi.org/10.1109/SMARTSENS.2015.7873609.
Bahri N, Amor WO (2019) Intelligent power supply management of an autonomous hybrid energy generator. Int J Sustain Eng 12:312–332. https://doi.org/10.1080/19397038.2019.1581852
Pugh TA, MacKenzie AR, Whyatt JD, Hewitt CN (2012) Effectiveness of green infrastructure for improvement of air quality in urban street canyons. Environ Sci Technol 46:7692–7699. https://doi.org/10.1021/es300826w
Hossain MF (2019) Sustainable technology for energy and environmental benign building design. J Build Eng 22:130–139. https://doi.org/10.1016/j.jobe.2018.12.001
Loucif M, Boumediene A (2015) Modeling and direct power control for a DFIG under wind speed variation. In: Proceedings of the 2015 3rd international conference on control engineering and information technology (CEIT); 2015 May 15–27; Tlemcen, Algeria. https://doi.org/10.1109/CEIT.2015.7233042.
Heydari M, Smedley K (2015) Comparison of maximum power point tracking methods for medium to high power wind energy systems. In: Proceedings of the 20th conference on electrical power distribution networks conference (EPDC); 2015 April 28–29; Zahedan, Iran. https://doi.org/10.1109/EPDC.2015.7330493.
Saidi Y, Mezouar A, Miloud Y, Benmahdjoub MA (2018) A robust control strategy for three phase voltage t source PWM rectifier connected to a PMSG wind energy conversion system. In: Proceedings of the international conference on electrical sciences and technologies in Maghreb (CISTEM); 2018 Oct. 28–31; Algiers, Algeria. https://doi.org/10.1109/CISTEM.2018.8613359.
Ligang H, Xiangdong W, Kang Y (2015) Optimal speed tracking for double fed wind generator via switching control. In: Proceeding of the 27th Chinese control and decision conference (2015 CCDC); 2015 May 23–25; Qingdao, China; https://doi.org/10.1109/CCDC.2015.7162368
Elmansouri A, El-mhamdi J, Boualouch A (2016) Wind energy conversion system using DFIG controlled by back-stepping and RST controller. In: Proceedings of the international conference on electrical and information technologies (ICEIT); 2016 May 4–7; Tangiers, Morocco. https://doi.org/10.1109/EITech.2016.7519612.
Elyaalaoui K, Ouassaid M, Cherkaoui M (2016) Supervision system of a wind farm based on squirrel cage asynchronous generator. In: Proceedings of the international renewable and sustainable energy conference (IRSEC); 2016 Nov 14–17; Marrakech, Morocco. https://doi.org/10.1109/IRSEC.2016.7983874.
Lap-Arparat P, Leephakpreeda T (2019) Real-time maximized power generation of vertical axis wind turbines based on characteristic curves of power coefficients via fuzzy pulse width modulation load regulation. Energy 182:975–987. https://doi.org/10.1016/j.energy.2019.06.098
Venkatesan C, Sundararaman K, Gopalakrishnan M (2017) Grid integration of PMSG based wind energy conversion system using variable frequency transformer. In: Proceedings of the international conference on intelligent computing, instrumentation and control technologies (ICICICT); 2017 July 6–7; Kannur, India. https://doi.org/10.1109/ICICICT1.2017.8342783.
Junyent-Ferre A, Gomis-Bellmunt O (2011) Wind turbine generation systems modeling for integration in power systems. In: Zobaa AF, Bansal R (eds) Handbook of renewable energy technology. World Scientific, Singapore, pp 53–68
Mahato SN, Singh SP, Sharma MP (2013) Dynamic behavior of a single-phase self-excited induction generator using a three-phase machine feeding single-phase dynamic load. Int J Electr Power Energy Syst 47:1–12. https://doi.org/10.1016/j.ijepes.2012.10.067
Bakhsh FI, Khatod DK (2014) A novel method for grid integration of synchronous generator-based wind energy generation system. In: Proceedings of the IEEE international conference on power electronics drives and energy systems (PEDES); 2014 Dec 16–19; Mumbai, India. https://doi.org/10.1109/pedes.2014.7041995.
Acknowledgements
This research was supported by Green Globe Technology under grant RD-02019-06 for building a better environment. Any findings, predictions, and conclusions described in this article are solely performed by the author; and it is confirmed that there is no conflict of interest for publishing this research paper in a suitable journal.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Hossain, M.F. Application of wind energy into the transportation sector. Int. J. of Precis. Eng. and Manuf.-Green Tech. 8, 1225–1237 (2021). https://doi.org/10.1007/s40684-020-00235-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40684-020-00235-1