Skip to main content
SpringerLink
Log in

Temperature-Dependent Material Property Databases for Marine Steels—Part 4: HSLA-100

  • Technical Article
  • Published:
Integrating Materials and Manufacturing Innovation Aims and scope Submit manuscript

Abstract

Integrated Computational Materials Engineering (ICME)-based tools and techniques have been identified as the best path forward for distortion mitigation in thin-plate steel construction at shipyards. ICME tools require temperature-dependent material properties—including specific heat, thermal conductivity, coefficient of thermal expansion, elastic modulus, yield strength, flow stress, and microstructural evolution—to achieve accurate computational results for distortion and residual stress. However, the required temperature-dependent material property databases of U.S. Navy-relevant steels are not available in the literature. Therefore, a comprehensive testing plan for some of the most common marine steels used in the construction of U.S. Naval vessels was completed. This testing plan included DH36, HSLA-65, HSLA-80, HSLA-100, HY-80, and HY-100 steel with a nominal thickness of 4.76 mm (3/16-in.). This report is the fourth part of a seven-part series detailing the pedigreed steel data. The first six reports will report the material properties for each of the individual steel grades, whereas the final report will compare and contrast the measured steel properties across all six steels. This report will focus specifically on the data associated with HSLA-100 steel.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Fig. 27
Fig. 28
Fig. 29
Fig. 30
Fig. 31
Fig. 32
Fig. 33
Fig. 34
Fig. 35
Fig. 36
Fig. 37
Fig. 38
Fig. 39
Fig. 40

Similar content being viewed by others

References

  1. Andersen LF (2000) Residual stresses and deformations in steel structures. Department of Naval Architecture and Offshore Engineering, University of Denmark

    Google Scholar 

  2. MIL-S-22698C (1988) Military specification: steel plate, shapes, and bars, weldable ordinary strength and higher strength: structural

  3. ASTM A945/M-16 (2016) Standard specification for high-strength low-alloy structural steel plate with low carbon and restricted sulfur for improved weldability, formability, and toughness. ASTM International, West Conshohocken, PA

  4. NAVSEA Technical Publication T9074-BD-GIB-010/0300 Rev. 2 (2012) Base materials for critical applications: requirements for low alloy steel plate, forgings, castings, shapes, bars, and heats of HY-80/100/130 and HSLA-80/100"

  5. Bechetti DH, Semple JK, Zhang W, Fisher CR (2020) Temperature-dependent material property database for marine steels – Part 1: DH36. Integr Mater Manuf Innov 9:257–286

    Article  Google Scholar 

  6. Semple JK, Bechetti DH, Zhang W, Fisher CR (2022) Temperature-dependent material property databases for marine steels—Part 2: HSLA-65. Integr Mater Manuf Innov 11:13–40

    Article  Google Scholar 

  7. Semple JK, Bechetti DH, Zhang W, Fisher CR (2022) Temperature-dependent material property databases for marine steels—Part 3: HSLA-80. Integr Mater Manuf Innov 11:648–674

    Article  Google Scholar 

  8. Fisher CR, Semple JK, Bechetti DH and Zhang W (2023) Temperature-dependent material database: HSLA-100. https://doi.org/10.13011/m3-5gh4-n325

  9. ASTM E417-17 (2017) Standard test method for analysis of carbon and low-alloy steel by spark atomic emission spectrometry. ASTM International, West Conshohocken, PA

  10. Eisler GR and Fuerschbach PW (1997) SOAR: an extensible suite of codes for weld analysis and optimal weld schedules. In: Seventh International conference on computer technology in welding, San Francisco, CA

  11. ASTM E1461-13 (2013) Standard test method for thermal diffusivity by the flash method. ASTM International, West Conshohocken, PA

  12. ASTM E1269-11 (2018) Standard test method for determining specific heat capacity by differential scanning calorimetry. ASTM International, West Conshohocken, PA

  13. ASTM A370-18 (2018) Standard test methods and definitions for mechanical testing of steel products. ASTM International, West Conshohocken, PA

  14. ASTM E21-17 (2017) standard test methods for elevated temperature tension tests of metallic materials. ASTM International, West Conshohocken, PA

  15. Huang TD, Harbison M, Scholler S, Rucker H, Hu J, Dong P, Collette M, Chung M, Groden M, Zhang W, Semple J, Kirchain R, Roth R, Bustamante M, Yang Y, Dull R, Gooroochurn Y, Doroudian M, Fisher CF, Sinfield M, Kihl D and Gonzalez A (2016) Robust distortion control methods and implementation for construction of lightweight metallic structures. SNAME Trans

  16. Hehemann RF, Kinsman KR, Aaronson HI (1972) A debate on the bainite reaction. Metall Trans 3:1077–1094

    Article  CAS  Google Scholar 

  17. Aaronson HI, Spanos G, Reynolds WT (2002) A progress report on the definitions of bainite. Scripta Mater 47(3):139–144

    Article  CAS  Google Scholar 

  18. Aaronson HI, Enomoto M, Lee JK (2010) Mechanisms of diffusional phase transformations in metals and alloys. CRC Press, Boca Raton, FL

    Google Scholar 

  19. Easterling K (1992) Introduction to the physical metallurgy of welding, 2nd edn. Butterworth-Heinemann, Oxford

    Google Scholar 

  20. Na S-H, Seol J-B, Jafari M, Park C-G (2017) A correlative approach for identifying complex phases by electron backscatter diffraction and transmission electron microscopy. Appl Microsc 47(1):43–49

    Article  Google Scholar 

  21. Das S, Ghosh A, Chatterjee S, Rao PR (2003) Microstructural characterization of controlled forged HSLA-80 steel by transmission electron microscopy. Mater Charact 50(4–5):305–315

    Article  CAS  Google Scholar 

  22. Fonda RW, Spanos G (2000) Microstructural evolution in ultra-low-carbon steel weldments—part i: controlled thermal cycling and continuous cooling transformation diagram of the weld metal. Metall Mater Trans A 31:2145–2153

    Article  Google Scholar 

  23. Fonda RW, Spanos G and Vandermeer RA (1994) Observations of plate martensite in a low carbon steel. Scripta Metall Mater 31(6)

  24. Valencia JJ, Papesch C (2007) thermophysical properties and high temperature tensile properties of HSLA-100 steel plate. Naval Metalworking Center as operated by Concurrent Technologies Corporation, Johnstown, PA

    Google Scholar 

  25. Yurioka N, Oshita S, Tamehiro H (1983) Determination of necessary preheating temperature in steel welding. Weld J 52(6):147–153

    Google Scholar 

  26. Yue X, Lippold JC, Alexandrox BT, Babu SS (2012) Continuous cooling transformatoin behavior in the CGHAZ of naval steels. Weld J 91(3):67–75

    Google Scholar 

  27. ASTM E1382-97 (2015) Standard test methods for determining average grain size using semiautomatic and automatic image analysis. ASTM International, West Conshohocken, PA

  28. Mohanty RR, Fonstein N, Girina O (2011) Effect of heating rate on the austenite formation in low-carbon high-strength steels annealed in the intercricial region. Metall Mater Trans A 42A(12):3680–3690

    Article  Google Scholar 

  29. Oliveira FLG, Andrade MS, Cota AB (2007) Kinetics of austenite formation during continuous heating in a low carbon steel. Mater Charact 58:256–261

    Article  CAS  Google Scholar 

  30. Apple CA, Krauss G (1972) The effect of heating rate on the martensite to austenite transformation in Fe–Ni–C Alloys. Acta Mater 20:849–856

    Article  CAS  Google Scholar 

  31. Heinze C, Pittner A, Rethmeiri M, Babu SS (2013) Dependency of martensite start temperature on prior austenite grain size and its influence on welding-induced residual stress. Comput Mater Sci 69:251–260

    Article  CAS  Google Scholar 

  32. Shome M, Mohanty ON (2006) Continuous cooling transformation diagrams applicable to the heat-affected zone of HSLA-80 and HSLA-100 steels. Metall Mater Trans A 37A:2159–2169

    Article  CAS  Google Scholar 

  33. Taljat B, Radhakrishnan B, Zacharia T (1998) Numerical analysis of GTA welding process with emphasis on post-solidification phase transformation effects on residual stress. Mater Sci Eng A A246:45–54

    Article  CAS  Google Scholar 

  34. Bainite Committee of The Iron and Steel Institute of Japan (1992) Atlas for Bainitic Microstructures, Vol. 1: Continuous-Cooled Microstructures of Low Carbon HSLA Steels, The Iron & Steel Institute of Japan

  35. Bhadeshia HKDH, Honeycombe RWK (2006) Steels: microstructure and properties, 3rd edn. Butterwoth-Heinemann, Oxford, UK

    Google Scholar 

  36. Sinha AK (1989) Ferrous physical metallurgy. Butterworth Publishers, Stoneham, MA

    Google Scholar 

  37. Thewlis G (2004) Classification and quantification of microstructures in steels. Mater Sci Technol 20:143–160

    Article  CAS  Google Scholar 

  38. International Institute of Welding (1985) Compendium of weld metal microstructures and properties: submerged-arc welds in ferritic steel. Woodhead Publishing, Cambridge, UK

    Google Scholar 

  39. Bhadeshia H (2019), Bainite in steels: theory and practice, 3rd edn. CRC Press, Boca Raton, FL

  40. Bhagat A, Pabi S, Ranganathan S, Mohanty O (2004) Aging behaviour in copper bearing high strength low alloy steels. ISIJ Int 44(1):115–122

    Article  CAS  Google Scholar 

  41. Sun M, Xu Y, Wang J (2020) Effect of aging time on microstructure and mechanical properties in a Cu-bearing marine engineering steel. Materials 13(16):1–12

    Article  CAS  Google Scholar 

  42. Valencia JJ, Papesch C (2005) Automated thermal plate forming: apparent specific heat and thermal expansion during heating of HSLA-80 and DH-36 steel plates. Naval Metalworking Center as operated by Concurrent Technologies Corporation, Johnstown, PA

    Google Scholar 

  43. Andersson JO, Herlander T, Hoglund L, Shi PF, Sundman B (2002) Thermo-Calc & DICTRA, computational tools for materials science. Calphad 26:92–101

    Article  Google Scholar 

  44. Spanos G, Fonda R, Vandermeer R, Matuszeski A (1995) Microstructural changes in HSLA-100 steel thermally cycled to simulate the heat-affected zone during welding. Metall Mater Trans A 26A:3277–3293

    Article  CAS  Google Scholar 

  45. Peet M (2014) Prediction of martensite start temperature. Mater Sci Technol 31(11):1370–1375

    Article  Google Scholar 

  46. Kang S, Yoon S, Lee S-J (2014) Prediction of bainite start temperature in alloy steels with difference grain sizes. ISIJ Int 54(4):997–999

    Article  CAS  Google Scholar 

  47. Capdevilla C, Caballero FG, Garcia de Andres C (2002) Determination of Ms temperature in steels: a bayesian neural network model. ISIJ Int 42:894–902

    Article  Google Scholar 

  48. Kirkaldy JS and Venugopalan D (1984) Phase transformations in ferrous alloys. In: Phase transformations in ferrous alloys: proceedings of an international conference, Philadelphia, PA

  49. ASTM E111-17 (2017) Standard test method for young's modulus, tangent modulus, and chord modulus. ASTM International, West Conshohocken, PA

  50. E. 1993-1-1 (2005) Eurocode 3: Design of steel structures - Part 1–1: General rules and rules for buildings

  51. E. 1993-1-2 (2005) Eurocode 3: Design of steel structures - Part 1–2: General rules - Structural fire design

Download references

Acknowledgements

The work was funded by the Office of Naval Research (ONR) in support of the Lightweight Innovations for Tomorrow (LIFT) Institute’s program entitled, Robust Distortion Control Methods and Implementation for Construction of Lightweight Metallic Structures – ICME Extension to Advanced Alloys. The authors would like to thank Huntington Ingalls Industries – Ingalls Shipbuilding for supplying the steel material tested for this program, as well as all team members who worked on the LIFT Joining-R4-3 program.

Author information

Authors and Affiliations

  1. Naval Surface Warfare Center, Carderock Division (NSWCCD), West Bethesda, MD, USA

    Jennifer K. Semple, Daniel H. Bechetti & Charles R. Fisher

  2. The Ohio State University (OSU), Columbus, OH, USA

    Wei Zhang

Authors
  1. Jennifer K. Semple
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Daniel H. Bechetti
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Wei Zhang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Charles R. Fisher
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Charles R. Fisher.

Ethics declarations

Conflict of interest

On behalf of all authors, the corresponding author states that there is no conflict of interest.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Semple, J.K., Bechetti, D.H., Zhang, W. et al. Temperature-Dependent Material Property Databases for Marine Steels—Part 4: HSLA-100. Integr Mater Manuf Innov 12, 130–156 (2023). https://doi.org/10.1007/s40192-023-00299-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40192-023-00299-2

Keywords

Search

Navigation