Abstract
The paper focuses on the behaviour of nonionic surfactants (NISs) for enhanced oil recovery (EOR) processes with special reference to its applicability in the reservoirs of Upper Assam. The present work specifically studies three NISs, viz. Tergitol 15-s-7(Tg7), Tergitol 15-s-9 (Tg9) and Triton X 405(TX), based on their surface tension (ST), dynamic interfacial tension, hydrophilic–lipophilic balance, emulsion stability, aqueous stability, particle size analysis and phase behaviour. Simultaneously, crude oil from an oil field of upper Assam Basin was characterized based on API gravity, kinematic and dynamic viscosities, pour point and acid number. Core flood studies were conducted in the reservoir core to determine the recovery of crude oil during secondary water flood and EOR by NISs. It was observed that Tergitol 15-S-7 when mixed with Triton X-405 (Tg7TX) had the least interfacial tension (IFT) as compared to individual NIS and their mixtures. The recovery was found to be as high as 25.67% after secondary water flood from the original oil in place when Tg7TX followed by chase water was used as an exotic fluid for EOR. This work is an attempt to identify NISs mixtures for EOR for Upper Assam Basin.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Due to the increasing human population, the ever-increasing demand for energy specially hydrocarbon energy cannot be satisfied. The easily extractable volume of crude has already been exhausted, and most of the reservoirs are at their depleting stage of production. Therefore, EOR techniques have been introduced to increase oil production in matured or underperforming reservoirs. At present, the exploration & production industry is putting a lot of emphasis on the development, optimization and implementation of new EOR methods (Gogoi 2014a, b).
Most matured or underperforming reservoirs of Upper Assam Basin are under chemical EOR (Gogoi 2011, 2014a, b). Already slugs comprising of anionic surfactant/surfactants/alkali EOR flooding were attempted in most reservoirs of Upper Assam Basin (Phukan et al. 2018; Hazarika and Gogoi 2014). These slugs reduce IFT between the aqueous and oleic phases which in turn increase the capillary number to overcome the capillary forces increasing the microscopic displacement efficiency of the reservoir.
In this study, various NISs were characterized based on ST, IFT, emulsion properties, HLB, particle size analysis and phase behaviour studies. Since the selection of appropriate surfactant also depends on the subsurface fluid properties, characterization of crude oil was done based on API gravity, kinematic & dynamic viscosities, pour point and acid number. The best-fitted NIS EOR slug was selected based on NIS properties, NIS and reservoir brine interactions and crude oil characterization.
Although anionic surfactants are most widely studied for EOR applications by many authors (Kakoty and Gogoi 2018; Barman et al. 2018; Hazarika et al. 2018; Das and Gogoi 2015), but certain characteristic properties of NIS make it more efficient for instance, its ultra-low IFT, non-volatility and environment friendly surfactant. They have effective solubilization towards water-insoluble or moderately soluble organic compounds and have the capability to alter surface characteristics and are stable at high salinity and temperature (Lawson 1978).
Materials and methods
Material
Three NISs under study Tg7, Tg9 and TX were procured from Sigma-Aldrich, Germany. Sodium chloride (NaCl) of 98% purity was used for the preparation of brine. Distilled water (DW) was obtained from a DW plant. The crude oil sample was collected from an oil field of upper Assam Basin. The other chemicals used were acetone, polyacrylamide (PAM), potassium hydroxide (KOH), phenolphthalein (colour indicator) and ethanol.
Methods
Characterization of crude oil properties
Specific gravity (SG) was measured using hydrometer (range 0.9–0.8 SG). API, kinematic viscosity, pour point and acid number were determined by IP standards of 24/55, Cannon–Fenske Routine Viscometer of size 100, standard IP method (15/67) and standard IP method (1/64), respectively (Gogoi et al. 2018).
Characterization of NIS/NISs
Formulation of the EOR slug
The static STs of three NIS (Tg7, Tg9 and TX) were measured in Kruss Easy Dyne S Tensiometer to determine the Critical Micelle Concentration (CMC). The CMCs were obtained for these three NIS at the lowest STs. CMC of Tg7 was mixed with Tg9, CMC of Tg9 was mixed with TX, CMC of Tg7 was mixed with TX, and CMC of Tg7 was mixed with Tg9 and TX as in Table 1. This was done to determine the lowest ST in case of NISs.
The dynamic IFT was determined for Tg7, TX and Tg7TX as in Table 1 with crude oil as the oleic phase by spinning drop tensiometer of model M6500. This was done to understand the behaviour of NIS/NISs with crude oil in terms of IFT reduction (Li et al. 2007; Nagaranjan and Wasan 1993).
Determination of HLB of the NIS/NISs
The HLB of a NIS is a measure of the degree to which it is hydrophilic or lipophilic. The HLB of the mixture of NISs was calculated as shown below: (Gadhave 2014).
HLB mixture = x HLBA + (1 − x) HLBB
X = xHLBA + HLBB − xHLBB
X = x(HLBA-HLBB) + HLBB
X − HLBB = x(HLBA − HLBB)
x = \(\frac{{X - {\text{HLBB}}}}{{x\left( {{\text{HLBA}} - {\text{HLBB}}} \right)}}\)
where A & B are two individual NIS
-
x & (1 − x) are the HLB fraction of A & B in the NIS mixtures
-
X is the HLB value for combined A & B NIS
-
HLBA & HLBB are the HLB values for the individual NIS (A & B)
Determination of emulsion stability of NIS/NISs
The crude-NISs emulsion stabilities were measured using the conventional bottle test method at 27 °C and 40 °C. Brine salinity of 3500 ppm was prepared and mixed with the seven set of NIS and NISs slugs at their CMC values. Each aqueous solution was mixed thoroughly using magnetic stirrer for 24 h until a homogenous solution was formed. These solutions were added to crude oil in the ratios of 1:9, 2.5:7.5, 5:5, 7.5:2.5 and 9:1. After addition of crude oil, the mixtures were agitated for approximately 30 min using a rotameter until a homogeneous solution was formed. The tubes were first allowed to stand undisturbed for 24 h at ambient temperature. The above process was repeated, the tubes were allowed to stand for 24 h at 40 °C, and the readings were recorded.
Determination of aqueous stability of NIS/NISs
In aqueous stability tests, concentrated stock solutions of NIS/NISs and brine of concentrations 3000, 3500, 4000, 4500, 5000, 5500, 6000 ppm were mixed in a glass vial, agitated and allowed to settle for 1 hour. If the chemicals forming NIS/NISs were unstable in brine at a given salinity and temperature, they will either deposit or separate into distinct dispersed phases. Aqueous stability tests provide an upper value of salinity below which all chemical constituents can coexist in the aqueous phase.
Particle size analysis of Tg7, TX and Tg7TX
The particle size analysis of Tg7, TX and Tg7TX were measured by a laser diffraction method of Zetasizer version 7.11 (Malvern Instruments Ltd.). Size of the droplets was measured based on the best fit between the experimental values and the Mie theory (Bera et al. 2012). The software used a dispersant RI of 1.33 during the measurement. All the experiments were conducted at 26 °C.
Phase behaviour study for Tg7TX
The phase behaviour studies were conducted following Winsor’s Classification of Microemulsion (Liu 2008). The NIS slug for this experiment was Tg7TX selected on the basis of the lowest IFT as obtained in “Formulation of the EOR slug” section. Equal volumes of crude oil (5 ml) and Tg7TX (5 ml) were taken in tarsons and mixed in rotary mixer for 1 h at 10 rpm. These mixtures were transferred into the sealed pipettes and kept undisturbed at oven temperature of 67 °C till stable microemulsions were formed.
Core flooding
Conventional core sample obtained was cut into core plug of 3.5 inches long and 1.5 inches diameter. The plug was cleaned by extracting oil present in the plug by toluene: methanol ratio of 1:1 in a Soxhlet apparatus. Sonication was done in a Digital Ultrasonic Cleaner [Model no. EI500HI] to remove the loose adhering particles on the plug surface and then dried in the dehumidifier till a constant weight is attained. The plug was then coated in Teflon and then inserted into the Hassler core holder of the core flood apparatus. The core flooding experiments were done as in the literature (Gogoi 2014a). Brine flooding was done to saturate the plug and obtain the absolute permeability (K) of the plug. Liquid paraffin oil of API gravity 36o was used for flooding, as this resemble the API gravity of crude used in this study. There is a limitation of using crude oil in the core flood apparatus as it might block the piping system. Oil flooding was done to obtain the relative permeability of oil w.r.t brine (krw) at initial water saturation Swi. This was followed by secondary brine flooding to obtain the relative permeability of brine w.r.t oil (kro) at residual oil saturation Sor. Finally, the Sor was being flooded by the formulated NISs which was Tg7TX until residual oil saturation after Tg7TX (SorT) flooding attains a constant value.
The interpretation of this displacement phenomenon occurring in the core flooding apparatus is based on the flow of any homogeneous fluid in a porous solid medium and was attributed to the French engineer Henry Darcy, assuming that all fluids flow in a direction perpendicular to the surfaces of constant pressure and in the direction of pressure decrease (Welge 1952).
Results and discussion
Characterization of crude oil properties
The results of characterization of crude oil properties are in Table 2. This was done to select the synthetic oil for core flooding experiments.
Characterization of NIS/NISs
Formulation of the EOR slug
The ST of three single NISs samples Tg7, Tg9 and TX is in Fig. 1 and Table 3. The CMC values of these NISs were mixed as in Table 1, and the STs for four mixed NISs, viz., Tg7Tg9, Tg7TX, Tg9TX and TTT, are shown in Table 4. Similar studies were also done by (Mandal et al. 2012). The lowest value of ST was observed in Tg7TX as in Table 4.
In Table 5, the IFT results of Tg7 and TX and Tg7TX are shown, wherein the least IFT was observed in Tg7TX indicating the best EOR slug. Besides, the IFTs of Tg7 and TX were also done since these are the individual NIS in the formulation of Tg7TX. Previous studies by (Torrealba and Johns 2018b) showed that the CMC values in the presence of crude oil may vary based on both the surfactant partitioning and also the water–oil ratio.
HLB of the NIS/NISs
HLB is an important parameter and is specifically calculated for NISs. The NIS depicts broadest range of properties depending upon the ratio of the HLB. Hence, selection of optimal HLB values of NISs for different applications is mandatory according to (Griffin 1954). It is a measure of per cent ethoxylation of the respective surfactant. Table 6 quantifies the affinity of the NIS’s for water and oil. Higher the HLB value, more desirable it is for EOR applications. From Table 6, the ethoxylation number can be correlated with HLB. It can be seen that an increase in ethoxylation number (EON) also results in the increase in HLB.
Crude and NIS/NISs emulsion stability
Crude-NIS/NISs emulsion stabilities were tested to check whether the NIS/NISs were stable when they were in contact with crude oil. This test enables us to determine the most efficient NIS/NISs (Almohsin et al. 2018). The instability of emulsions leads to floating of droplets to the surface, cohesion between droplets and finally separation as discussed in (Salager et al. 2000). The stability of the emulsions depends on the different forces acting on the interface. These include electrostatic repulsive forces and van der Waals attractive forces (Mileva and Radoev 2004). The NIS/NISs were prepared with distilled water and brine of 3500 ppm and agitated for 1 hour. Crude oil and NIS/NISs were then mixed in different proportions to determine which proportion results in stable emulsions. From the experiment in “Determination of Emulsion Stability of NIS/NISs” section, it was observed that all the NIS/NISs showed the maximum stability at crude oil: NIS/NISs concentration of 9:1 at both 27 °C and 40 °C and the least stable was observed at crude oil: NIS/NISs ratio of 1:9 when kept under 48 h of observation. The results obtained are shown from Table 7.
Determination of aqueous stability of the NIS/NISs
Aqueous stability tests were carried out to test the stability of chemicals in the electrolyte solution at salinities encountered during corefloods. The NIS’s surfactant slug was prepared at 3000, 3500, 4000, 4500, 5000, 5500, 6000 ppm salinity at their CMC concentrations. It was observed that they were stable at all the above brine salinity. There was no separation of phases in the solution. These depict that different range of salinity of the reservoir condition will not affect the stability of the NIS/NISs.
Particle size analysis of Tg7, TX and Tg7TX
Particle size distributions for Tg7, TX and Tg7TX in DW and brine are shown in Fig. 2a–f, respectively. The size of Tg7, TX and Tg7TX droplets was found to be less than 10 nm in all the cases. The nanosize of Tg7, TX and Tg7TX slugs is smaller than the pore throats of the reservoir porous media assisting good injectivity and penetration through the smaller pores and increasing microscopic displacement efficiency (Sajjadian et al. 2016). The curves in each case show % number versus particle size distribution. The Z-average diameter is the mean hydrodynamic diameter and is calculated according to the International Standard on dynamic light scattering ISO13321 (Bera et al. 2012) The Z-average diameter is intensity weighted and is therefore sensitive to the presence of large particles. The results of the particle size analysis of the Tg7, TX and Tg7TX are shown in Table 8. The relation between Tg7, TX and Tg7TX HLB and Z-average diameter of the particle is shown in Fig. 3. From Fig. 3, it can be understood that with increase in HLB, there is a significant decrease in Z-average diameter thereby increasing Tg7, TX and Tg7TX activity and efficiency (Mandal and Bera 2012; Mandal et al. 2012). Again, peak size diameter is also correlated with the dynamic IFT of Tg7, TX and Tg7TX as shown in Fig. 4 (Torrealba and Johns 2017). Z-average diameter corresponds to the mean, with the square root of the polydispersity index (PDI) corresponding to the relative standard deviation of that distribution. However, obtaining a Z-average and PDI does not mean that the distribution is normal distribution, also known as Gaussian distribution as in Figs. 2a–f, although smaller PDI values are a good indication that a Gaussian might be a reasonable approximation of the real size distribution (https://www.materials-talks.com/wp-content/uploads/2014/07/FAQ-What-is-z-average.pdf).
a Particle size distribution of Tergitol 15-S-7 + TX-405 in DW. b Particle size distribution of Tergitol 15-S-7 + TX-405 in 2000 ppm brine. c Particle size distribution of Tergitol 15-S-7 in DW. d Particle size distribution of Tergitol 15-S-7 in 2000 ppm brine. e Particle size distribution of TX-405 in DW. f Particle size distribution of TX-405 in 2000 ppm brine
The Z-average is maximum for Tg7-DW and minimum in TX-DW. Peak size diameter is maximum in case of Tg7TX-DW and minimum in case of Tg7-brine, indicating that better nano-sized particles are in Tg7-brine. With respect to particle size distribution characterization, a parameter used to define the size range of Tg7, TX and Tg7TX in brine is called the “polydispersity index” (PDI). The term “polydispersity” (or “dispersity” as recommended by IUPAC) is used to describe the degree of non-uniformity of a size distribution of particles (Nobbmann 2014; Bera 2015). Polydispersity index is also known as heterogeneity index, which is a measure of the distribution of molecular mass in a given test sample. This index is dimensionless and scaled such that values smaller than 0.05 are mainly seen with highly monodisperse standards. PDI values bigger than 0.7 indicate that the sample has a very broad particle size distribution and is heterogeneous. The calculations used for the determination of size and PDI parameters are defined in the ISO standard documents 13321:1996 E and ISO 22412:2008 (Worldwide 2011). In this case, the particle size analysis of Tg7, TX and Tg7TX is in the range of 0.264–0.561, and the least was for Tg7 in brine, while the highest was for TX-brine and the average was 0.434, indicating polydisperse inclined towards heterogeneity as it is closer to 0.7 than to 0.05.
Phase behaviour study for Tg7TX
The phase behaviour of microemulsions is important to EOR because it can be used as an indicator of ultra-low IFT. Winsor in 1954 first described the phase behaviour of microemulsions for surfactant, oil and brine system. The phase behaviour of a microemulsion system is a function of types and concentration of surfactants, cosurfactants, oil, brine, alcohol, temperature (Bera et al. 2012). With increase in salinity, the phase behaviour of crude oil NIS/NISs mixtures changes from Winsor type I to III to II (Torrealba and Johns 2018a, b) . The ideal situation to achieve ultra-low IFT is during Winsor type III formation, and the salinity at which it is formed is called optimal salinity. The salinity where the two tensions are equal is called the optimum salinity, which is one of the most significant quantities in the surfactant EOR. At optimum salinity, the amount of oil and brine solubilized in the surfactant phase is approximately equal (Riswati et al. 2019).
The oil solubilization ratio is the volume of oil present in the microemulsion phase to volume of total active Tg7TX, whereas water solubilization ratio is the volume of water present in a microemulsion to volume of Tg7TX present in the sample. At optimum solubilization ratio, the oil and water solubilization ratios are equal and corresponding salinity at the optimum solubilization ratio is referred to as optimal salinity. Microemulsion at the optimum salinity is in the middle of the Winsor Type III microemulsion. From Fig. 5, optimum solubilizing ratio or optimum salinity for the Tg7TX was observed at 4250 ppm.
Core flooding
Core flooding of the NIS’s was done to determine their recovery efficiencies. It was completed in four stages, firstly saturating the core with a brine salinity of 2000 ppm to determine the absolute permeability, secondly drainage process where the fully saturated core was flooded with liquid paraffin, followed by 1st imbibition process where secondary recovery commences and fourthly, 2nd imbibition process where NIS’s slug was injected to determine the additional recovery. During the 1st imbibition process, Swi and Soi for the four sets of experiment are shown in Table 9. Approximately 37.30%, 38.47%, 39.42 and 42.44% of oil from the original oil in place [OOIP] were recovered in 1st imbibition process or water flooding as in Fig. 6. So, a systematic investigation has been done for recovering remaining oil using Tg7, TX, Tg7TX and chase water assisted Tg7TX.
Conclusion
The research work attempts to identify NISs to be used as an exotic fluid for EOR in upper Assam Basin. From the results obtained, following conclusion can be made:
- 1.
The crude oil was characterized with an attempt to determine the feasibility of the use of NISs for EOR. Accordingly, the crude oil was found to be light, low viscous and of low acidity which supports surfactant EOR.
- 2.
The increase in ethoxylation number increases the CMC concentration of the NIS.
- 3.
Of all the NISs, the mixture of Tg7TX showed the lowest ST & IFT.
- 4.
NISs were characterized, and the most effective NISs mixture was Tg7TX. The HLB number of Tg7TX also showed emulsification and detergency properties, thus formed stable emulsion. The Z-average diameter of Tg7TX was also found to be less.
- 5.
Crude-NISs emulsion stability was observed at a ratio of 9:1. The same was also observed at 40 °C.
- 6.
Proper synergy between the NIS/NISs was observed owing to their aqueous stability and crude oil emulsion stability.
- 7.
NISs droplet size was found to be less than 10 nm, thus assisting mobilization of oil in pore throats and consequently increasing recovery efficiency.
- 8.
The phase behaviour experiments of the selected NISs, Tg7TX, the optimal salinity was observed at 4250 ppm, and the Winsor type III was observed at this particular brine concentration.
- 9.
From the core flood experiment, the amount of residual oil that can be recovered by the NIS’s was calculated and found to be 21%, 23.2%, 24%, 25.67% of OOIP for the NIS’s of Tg7, TX, Tg7TX and Tg7TX followed by chase water. The latter results in the maximum recovery efficiency that improves both microscopic and sweep efficiencies.
References
Almohsin AM, Alabdulmohsen Z, Bai B (2018) Experimental study of crude oil emulsion stability by surfactants and nanoparticles. In: Missouri University of Science and Technology. SPE EOR conference at Oil and Gas West Asia, Muscat, Oman. https://doi.org/10.2118/190440-MS
Barman J, Gogoi SB,Viswanathan J, Konwar D (2018) Formulation of chemical slug for EOR application of moran oil field of upper Assam Basin. In: Sustainability issues in environmental geotechnics, Springer Nature, proceedings of the 2nd GeoMEast: international congress and exhibition, pp 137–150. https://link.springer.com/chapter/10.1007/978-3-030-01929-7_10
Bera A (2015) Nanoporous silicon prepared by vapour phase strain etch and sacrificial technique. In Proceedings of the international conference on microelectronic circuit and system (Micro), Kolkata, India. pp 42–45. https://pdfs.semanticscholar.org/90d7/5357faa004f0cf15abf2ad458f8e1253f15d.pdf
Bera A, Kumar S, Mandal A (2012) Temperature-dependent phase behavior, particle size and conductivity of middle-phase microemulsions stabilized by ethoxylated nonionic surfactants. J Chem Eng Data 57(12):3617–3623. https://doi.org/10.1021/je300845q
Das BM, Gogoi SB (2015) Relating IFT with Oil recovery with special reference to bhogpara porous media of upper Assam Basin. J Pet Eng Technol 5(1):1–8
Gadhave A (2014) Determination of hydrophilic–lipophilic balance value. Int J Sci Res (IJSR) 3(4):573–574
Gogoi SB (2011) Adsorption—desorption of surfactant for enhanced oil recovery. Transp Porous Media 90(2):589–604. https://doi.org/10.1007/s11242-011-9805-y
Gogoi SB (2014a) Effluent as surfactant for enhanced oil recovery. Innovative energy policies. J Innov Energy Policies 3(1):40–50. https://doi.org/10.4172/2090-5009.1000109
Gogoi SB (2014b) Petroleum technology—enhanced oil recovery techniques. Oxford & IBH, New Delhi, pp 45–64. ISBN 978-81-204-1778-6
Gogoi TJ, Gogoi SB, Sarmah S (2018) A Green Approach for Oil Field Produced waters of upper Assam Basin. In: Sustainability issues in environmental geotechnics, Springer Nature, Proceedings of the 2nd GeoMEast: international congress and exhibition, pp 151–171. https://doi.org/10.1007/978-3-030-01929-7
Griffin WC (1954) Calculation of HLB values of non-ionic surfactants. J Soc Cosmet Chem 5:249–256
Hazarika K, Gogoi SB (2014) Comparative study of an enhanced oil recovery process with various chemicals for Naharkatiya oil field. Int J Appl Sci Biotechnol 2(4):432–436. https://doi.org/10.3126/ijasbt.v2i4.11047
Hazarika K, Yadav R, Gogoi SB, Bhui U (2018) Characterization of crude oil for enhanced oil recovery: a study with anionic surfactant. Int J Ambient Energy 39(2):1–12. https://doi.org/10.1080/01430750.2017.1421573
https://www.materials-talks.com/wp-content/uploads/2014/07/FAQ-What-is-z-average.pdf
http://www.biophysics.bioc.cam.ac.uk/wp-content/uploads/2011/02/DLS_Terms_defined_Malvern.pdf
Kakoty M, Gogoi SB (2018) Evaluation of surfactant formulation for EOR in some depleted oil fields of upper Assam. In: Sustainability issues in environmental geotechnics, Springer Nature, proceedings of the 2nd GeoMEast: international congress and exhibition, pp 57–75. https://link.springer.com/chapter/10.1007/978-3-030-01929-7_5
Lawson JB (1978) The adsorption of non-ionic and anionic surfactants on sandstone and carbonate. In: SPE symposium on improved methods of oil recovery. SPE Journal. https://doi.org/10.2118/7052-MS
Li G, Prasad S, Dhinojwala A (2007) Dynamic interfacial tension at the oil/surfactant-water interface. Langmuir 23(20):9929–9932. https://doi.org/10.1021/la7014463
Liu S (2008) Alkaline surfactant polymer enhanced oil recovery process. Diss., Rice University. https://hdl.handle.net/1911/22224. Accessed Jan 2008
Mandal A, Bera A (2012) Surfactant stabilized nanoemulsion: characterization and application in enhanced oil recovery. In: World academy of science, engineering and technology, vol 6, pp 7. https://waset.org/publications/10032/surfactant-stabilized-nanoemulsion-characterization-and-application-in-enhanced-oil-recovery. Accessed 25 July 2012
Mandal A, Bera A, Ojha K and Kumar T (2012) Characterization of surfactant stabilized Nanoemulsion and its use in EOR. In: SPE international oilfield nanotechnology conference held in Noordwijk, The Netherlands. https://doi.org/10.2118/155406-MS
Mileva E, Radoev B (2004) Emulsions: structure stability and Interactions. In: Interface science and technology, Elsevier, vol 4, pp 215–258 https://www.elsevier.com/books/emulsions-structure-stability-and-interactions/petsev/978-0-12-088499-5. Accessed 14 Oct 2004
Nagaranjan R, Wasan DT (1993) Measurement of dynamic interfacial tension by an expanding drop tensiometer. J Colloid Interface Sci 159(1):164–173. https://doi.org/10.1006/jcis.1993.1308
Nobbmann UL (2014) Polydispersity–what does it mean for DLS and chromatography. http://www.materials-talks.com/blog/2014/10/23/polydispersity-what-does-it-mean-for-dls-and-chromatography. Accessed 10 July 2014
Phukan R, Gogoi SB, Tiwari P (2018) Alkaline-surfactant-alternated-gas/CO2 flooding: effects of key parameters. J Pet Sci Eng 173(2019):547–557. https://doi.org/10.1016/j.petrol.2018.10.043
Riswati Shabrina S, Bae Wisup, Park Changhyun, Permadi Asep K, Efriza Ivan, Min Byungun (2019) Experimental analysis to design optimum phase type and salinity gradient of alkaline surfactant polymer flooding at low saline reservoir. J Pet Sci Eng 173:1005–1019. https://doi.org/10.1016/j.petrol.2018.09.087
Sajjadian M, Sajjadianand V, Daya AA (2016) experimental investigation of using nano fluid to improve productivity index on enhancing oil recovery. Int J Min Sci (IJMS) 2(2):13–19. https://doi.org/10.20431/2454-9460.0202003
Salager JL, Marquez N, Graciaa A, Lachaise J (2000) Partitioning of ethoxylated octylphenol surfactants in microemulsion–oil–water systems: influence of temperature and relation between partitioning coefficient and physicochemical formulation. Langmuir 16(13):5534–5539. https://doi.org/10.1021/la9905517
Torrealba VA, Johns RT (2017) Coupled interfacial tension and phase behavior model based on micellar curvatures. Langmuir 33(47):13604–13614. https://doi.org/10.1021/acs.langmuir.7b03372
Torrealba VA, Johns RT (2018a) Microemulsion phase-behavior equation-of-state model using empirical trends in chemical potentials. SPE J 23(03):819–830. https://doi.org/10.2118/184555-PA
Torrealba VA, Johns RT (2018b) Partition-coefficient relations for improved equation-of-state description of microemulsion-phase behavior. SPE J. https://doi.org/10.2118/179845-PA
Welge Henry J (1952) A simplified method for computing oil recovery by gas or water drive. J Pet Technol SPE. https://doi.org/10.2118/124-G
Worldwide MI (2011) Dynamic light scattering common terms defined; inform white paper. Malvern Instruments Limited, Malvern, pp 1–6
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Sarmah, S., Gogoi, S.B., Xianfeng, F. et al. Characterization and identification of the most appropriate nonionic surfactant for enhanced oil recovery. J Petrol Explor Prod Technol 10, 115–123 (2020). https://doi.org/10.1007/s13202-019-0682-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13202-019-0682-1